Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “kinetic parameters”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 991 records · Page 55
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Operability of a Natural Gas–Air Rotating Detonation Engine

A combustor was developed to operate with natural gas and air as the primary propellants at elevated chamber pressures and air preheat temperatures representative of land-based power generation gas turbine engines. Detonation dynamics were studied to characterize the operability of rotating detonation-based pressure gain combustion systems for this application. Measurements of chamber wave dynamics were performed using high-frequency pressure transducers and high-speed imaging of broadband combustion chemiluminescence. The rotating detonation engine was tested with two injector configurations across a broad range of mass flux (200–500 kg/m 2 /s), equivalence ratio (0.85–1.2), and oxygen mass fraction (23.2–35%) conditions to determine the effect of operating parameters on the propagation of detonation waves in the combustor. Wave propagation speeds of up to 70% of the mixture Chapman–Jouguet detonation velocity and chamber pressure fluctuations greater than 4 times the mean chamber pressure were observed. Supplementing the air with additional oxygen, varying the equivalence ratio, and enriching the fuel with hydrogen revealed that combustor operability is sensitive to the chemical kinetics of the propellant mixture. Comparing the operational trends of the two injector configurations suggests that one design mixes the incoming propellants more effectively. Although most test conditions exhibited counter-rotating detonation waves within the chamber, the injector design with superior mixing characteristics was able to support single-wave propagation.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2023

In situ probing of interfacial roughness and transient phases during ceramic cold sintering process

The ceramic cold sintering process (CSP) offers an eco-friendly approach to producing fully dense ceramics at low temperatures. However, an incomplete mechanistic understanding hinders its optimization and widespread adoption. In this study, we analyze the microstructural and structural changes in ZnO, a model CSP system, using in situ synchrotron-based high-energy small-angle X-ray scattering and X-ray diffraction techniques. Our results reveal the time evolution of ZnO particles' surface area and roughness, reflecting the dissolution and re precipitation processes that enable densification. The in situ measurements supply valuable kinetic data for these stages of CSP. Alongside microstructural changes and densification, we observed the evolution of secondary phases representing reaction products between ZnO and acetic acid, the solvent used. The initial ZnO/solvent mixture's dominant secondary phase is attributed to zinc acetate, which is gradually replaced by a zinc soap-type structure during CSP. This structure has a large (≈ 21 Å) lattice parameter and is assumed to have a layered nature. The formation of this soap phase, which is retained in the sintered product as an intergranular component, appears to be a signature of successful cold sintering as it facilitates mass transport, leading to densification. Here, our study underscores the potential of in situ synchrotron characterization for revealing microstructural and phase-evolution details during CSP. These findings, which would be challenging to obtain through ex situ measurements, provide crucial data to guide and validate theoretical models, ultimately enhancing CSP's effectiveness and adoption.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Dark dimension and decaying dark matter gravitons

We explore the cosmology of the dark-dimension scenario taking into account perturbations in the linear regime. In the context of the dark-dimension scenario, a natural candidate for dark matter in our Universe is the excitations of a tower of massive spin-2 Kaluza-Klein (KK) gravitons. These dark gravitons are produced in the early Universe and decay to lighter KK gravitons during the course of cosmological evolution. The decay causes the average dark matter mass to decrease as the Universe evolves. In addition, the kinetic energy liberated in each decay leads to a kick velocity for the dark matter particles, leading to a suppression of structure formation. Using current cosmic microwave background (), baryon acoustic oscillation, and cosmic shear (KiDS-1000) data, we put a bound on the dark matter kick velocity today v today ≤ 2.2 × 10 − 4 c at 95% CL. This leads to rather specific regions of parameter space for the dark-dimension scenario. The combination of the experimental bounds from cosmology, astrophysics, and table-top experiments leads to the range l 5 ∼ 1 – 10 μ m for the size of the dark dimension. The dark-dimension scenario is found to be remarkably consistent with current observations and provides signatures that are within reach of near-future experiments. Published by the American Physical Society 2024

Astronomy & Astrophysics↗
DOE OSTI2024

Once-in-a-lifetime encounter models for neutrino media: From coherent oscillations to flavor equilibration

Collective neutrino oscillations are typically studied using the lowest-order quantum kinetic equation, also known as the mean-field approximation. However, some recent quantum many-body simulations suggest that quantum entanglement among neutrinos may be important and may result in flavor equilibration of the neutrino gas. In this work, we develop new quantum models for neutrino gases in which any pair of neutrinos can interact at most once in their lifetimes. A key parameter of our models is γ = μ Δ z , where μ is the neutrino coupling strength, which is proportional to the neutrino density, and Δ z is the duration over which a pair of neutrinos can interact each time. Our models reduce to the mean-field approach in the limit γ → 0 and achieve flavor equilibration in time t ≫ ( γ μ ) − 1 . These models demonstrate the emergence of coherent flavor oscillations from the particle perspective and may help elucidate the role of quantum entanglement in collective neutrino oscillations. Published by the American Physical Society 2024

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2024

A Physical Metric for Inertial Confinement Fusion Capsules

The performance of fusion capsules on the National Ignition Facility (NIF) is strongly affected by the physical properties of the hot deuterium–tritium (DT) fuel, such as the mass, areal density, and pressure of the hot spot at the stagnation time. All of these critical quantities depend on one measured quantity, which is the ratio of the specific peak implosion energy to the specific internal energy of the hot spot. This unique physical quantity not only can measure the incremental progress of the inertial confinement fusion capsules towards ignition but also measures the conversion of the peak implosion kinetic energy of the pusher shell into the internal energy of the hot fuel in a capsule. Analysis of existing NIF shots to date are performed. The ratio metric is compared quantitatively with the ignition criterion. Results provide new perspectives on the NIF experiments by which the performance of the burning plasma can be determined and controlled through the fine tune of the implosion parameters, which improves future designs and predictions of the ignition capsules.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Symbolic regression development of empirical equations for diffusion in Lennard-Jones fluids

Symbolic regression (SR) with a multi-gene genetic program has been used to elucidate new empirical equations describing diffusion in Lennard-Jones (LJ) fluids. Some examples include equations to predict self-diffusion in pure LJ fluids and equations describing the finite-size correction for self-diffusion in binary LJ fluids. The performance of the SR-obtained equations was compared to that of both the existing empirical equations in the literature and to the results from artificial neural net (ANN) models recently reported. It is found that the SR equations have improved predictive performance in comparison to the existing empirical equations, even though employing a smaller number of adjustable parameters, but show an overall reduced performance in comparison to more extensive ANNs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

A nanosecond pulsed discharge circuit model for engine applications

Non-equilibrium plasma discharges in spark gaps have been an increasingly studied method for alleviating cycle to cycle variation in lean and dilute combustion environments. However, ignition models that account for streamer propagation, cathode fall, and transmission line amplification over nanosecond time scales have so far not been developed. The present study develops such a model, with emphasis on the energy delivered from circuit to cylinder. Here, key pieces of the relevant physics and chemistry are summarized, simplified, and systematically coupled to one another. The set of parameters is limited to a handful of key observables and modeled using Modelica. Results show non-trivial behavior in the energy delivery characteristics of such discharges with important implications for ignition.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

AN ACID BAKING APPROACH TO ENHANCE RARE EARTH ELEMENT RECOVERY FROM BITUMINOUS COAL SOURCES

Rare earth elements (REE) are a group of 17 elements typically classified as light and heavy rare earth elements, which play a crucial role in developing the latest technologies for energy, defense, and medical sectors. Even though REEs have been found in more than 200 minerals, only bastnaesite, monazite and xenotime are commercially exploited for REE extraction. However, the recent exponential increase in REE demand has spurred countries such as the United States into research for the extraction of REEs from secondary sources such as coal, acid mine drainage, and coal ash. Several coal sources (e.g., Fire Clay seam coal) across the United States have been identified to contain elevated concentrations of rare earth elements (>600 ppm), and various researchers have investigated the feasibility of both physical and hydrometallurgical extraction techniques for rare earth concentration and subsequent extraction. However, both physical and direct leaching were concluded to be inefficient for RE beneficiation and extraction due to low recoveries. Alternatively, thermal treatment provides promising means for RE recovery from bituminous coal sources. The positive impact of thermal treatment/calcination was established to be due to the decarbonization and dehydroxylation of the clays, which released entrapped rare earth elements within the dominant minerals and converted them into an acid-soluble form. Nonetheless, the improvement in recovery was limited to the light REEs (LREEs) with an insignificant increase in the heavy REEs (HREE). It was demonstrated that the light and heavy REEs in the material were associated with difficult-to-leach minerals such as monazite, xenotime, and zircon, which were not decomposed by simple calcination due to their high thermal stability. Hence, roasting in the presence of chemicals was necessary to ensure the decomposition of those REE-containing minerals. As such, this study was focused on the acid baking treatment of bituminous coals with an aim to enhance REE recovery, especially HREEs. Based on the presence of REE minerals like monazite and xenotime, three pre-leach treatment methods, i.e., 1) roasting, 2) direct acid baking, and 3) acid baking after roasting were investigated. Roasting tests at 600 ⁰C revealed that the recovery of light REEs (LREEs) was enhanced while the recovery of HREEs remained relatively unaffected. LREE and HREE recovery values of 38.3% and 21.3%, respectively, were achieved using a 50 g/L sulfuric acid solution at 5% solid concentration and a solution temperature of 75 ⁰C for 2 hours. Comparatively, direct acid baking at 250 °C provided substantial increased LREE and HREE recovery values to approximately 49.4% and 53.0%, respectively, using an equivalent acid dosage. Recoveries were maximized to 77.0% and 79.6% for LREE and HREE, respectively, by roasting followed by acid baking. Similar results were obtained from the treatment of a second bituminous coal source. Due to strong correlations between REE and Al recovery values, tests were performed on kaolinite and illite, which were prominent clay minerals within the source coals. These experiments revealed that the REE recovery improvements were likely a result of dehydroxylation of clays and subsequent release and decomposition of REE-bearing minerals such as monazite, xenotime and zircon. Subsequently, a parametric study was conducted to identify the impact of acid baking parameters on rare earth element recovery. The factors investigated using a three-level statistical experimental program were acid baking time, acid solution concentration, baking temperature, and acid solution-to-solids ratio which were found to significantly impact REE and contaminant element (Al, Fe, and Ca) recovery. An increase in baking temperature up to around 250 ⁰C improved the light and heavy REE recovery values by more than 50 absolute percentage points relative to performances achieved when direct leaching. As aforementioned, acid baking was needed to both decompose the clay minerals and liberate the REE minerals, which allowed access for the acid to solubilize the REEs. Acid concentration of the solution used for acid baking was studied as a means of minimizing the amount of acid needed to achieve a target REE recovery. However, thermo-gravimetric and differential scanning calorimetry analysis (TGA-DSC) of sulfuric acid under oxidizing atmosphere revealed that the addition of water decreased the evaporation temperature, which explains the lower REE recovery values obtained when using acid concentrations less than 100%. Using pure sulfuric acid at an acid-to-solid ratio of 0.8:1 resulted in recovery values of around 70% for both LREEs and HREEs. The decomposition reaction time was relatively quick with 65% of the TREEs recovered within the first 10 minutes. Following the identification of optimum operating conditions through the parametric study, a systematic leaching study was carried out to examine the impact of leaching parameters, such as solid-to-liquid (S/L) ratio, temperature, and time, on REE recovery using acid baking conditions of 1:1 acid to solids ratio at 250 °C for 30 minutes. The solid-to-liquid ratio was varied from 1-20% by weight at 25 °C, 50 °C, and 75 °C solution temperatures. The results indicated that reaction time and solution temperature considerably impacted the recovery of heavy and light REEs. Interestingly, LREE recovery reduced from 68% at 5% S/L to 58% at 20%S/L, whereas HREE recovery of 78% remained unaffected. The decrease in the LREE recovery was determined to be due to La and Ce precipitation, likely through isomorphic substitution with calcium in gypsum. The kinetic data indicated that 67% LREE and 77% HREE recovery could be obtained within the first 15 minutes of the reaction, suggesting fast reaction kinetics. Furthermore, raising the solution temperature from 25 °C to 75 °C increased the LREE and HREE recovery from 60% and 32% to 67% and 79%, respectively. The kinetic modeling results demonstrated that the rate-limiting step in the LREE dissolution was diffusion and chemical reaction, whereas the HREE extraction was controlled by only chemical reaction. The leaching study concluded that using 20% S/L at 75 °C for 15 minutes maximized LREE and HREE recovery. The lab-scale precipitation study showed that Fe and Al in solution could be removed at pH 4.5 followed by REE precipitation at pH 6.0 using 6 mol/L NaOH. Finally, the bench-scale data was used to develop a process flowsheet for REE recovery from low-grade bituminous coal sources using acid baking. Finally, based on the proposed flowsheet, a concentrated RE-cake obtained through selective precipitation at pH 6.5 was re-leached using HCl at pH 1.5. The resultant leachate was used to identify the impact of various operating parameters on REE recovery and purity with an aim to maximize REE precipitation efficiency while minimizing the oxalic acid dosage. The operating parameters for this investigation were oxalic acid dosage, iron (III) contamination, solution pH and temperature. The resultant model suggested that oxalic acid dosage and reaction pH are the most significant factors for the REE precipitation efficiency, followed by the interaction of oxalic dosage and Fe concentration. Test results indicated that increasing the oxalic acid concentration from 0g/L to 80g/L improved the REE precipitation efficiency from approximately 4.2% to 95.0%. Furthermore, raising the solution pH from 0.5 to 2.5 considerably enhanced the precipitation efficiency from 0.0% to 98.9%. A solution temperature elevation decreased REE recovery, which indicated an exothermic reaction between REEs and oxalate anions. Finally, a high level of Fe contamination adversely impacted REE precipitation efficiency. The speciation analysis revealed that the dominant iron species in the solution system were Fe-(C₂O₄)₃³⁻, Fe-(C₂O₄)²⁻, and Fe-(C₂O₄)⁺, which consumed the majority of the oxalate anions

rare earth elements, acid baking, high-temperature↗
DOE OSTI2022

Multiple electron beam generation with different energies and comparable currents from a single cathode potential for high power traveling wave tubes (TWTs)

We present a technique for generating multiple electron beams with different energies and comparable currents from a single cathode stalk at a single potential using nested magnetically insulated coaxial diodes (MICDs). The application is for a multi-stream traveling wave tube. Particle-in-cell simulations are performed for an experimental parameter-based geometry where two thin-walled intense relativistic electron beams immersed in a strong uniform magnetic field propagate through a cylindrical vacuum channel. The analytically derived results are obtained by extending Fedosov’s solution for generating a hollow electron beam from an MICD on a cathode stalk in an infinite magnetic field. Two electron beams are generated and accelerated downstream assuming zero initial kinetic energy of the electrons from the cathodes. Results show both electron beam currents ranging from 66 to 2.8 kA with an energy difference ranging from 6% to 27% depending on voltages applied from 100 to 600 kV and the geometry of the two MICDs. An optimal geometry is a crucial factor in achieving the maximum energy difference between the electron beams for comparable currents. The analytical and numerical simulation results show good agreement. We are currently in the process of planning experiments using the electron beam accelerator (SINUS-6 at UNM) to validate the analytical and simulation results.

Islam, K. N. (ORCID:0000000214397710)↗
DOE OSTI2024

Simulating the Phonon Collection Efficiency in KIPMDs

Kinetic inductance phonon-mediated (KIPM) detectors use microwave kinetic inductance detectors (MKIDs) to read out phonon signals in the substrate. They are a promising class of detectors to be used in light dark matter (DM) searches due to their potential eV-scale sensitivity and native frequency-domain multiplexability. In order to improve upon the design of these detectors, simulations are needed to understand the effects of detector design on measurable physical parameters including the phonon collection efficiency, $\eta_{ph}$, which is defined as the ratio of phonon energy detected by the sensitive target element to the incident energy deposited in the substrate. This work simulates the phonon collection efficiency for a KIPMD currently operated at the Northwestern EXperimental Underground Site (NEXUS).

Dang, Stella Q.↗
DOE OSTI2024

Simulating the Phonon Collection Efficiency in Kinetic Inductance Phonon-Mediated Detectors

Kinetic inductance phonon-mediated (KIPM) detectors use microwave kinetic inductance detectors (MKIDs) to read out phonon signals in the substrate. They are a promising class of detectors to be used in light dark matter (DM) searches due to their potential eV-scale sensitivity and native frequency-domain multiplexability. In order to improve upon the design of these detectors, simulations are needed to understand the effects of detector design on measurable physical parameters including the phonon collection efficiency, $\eta_{ph}$, which is defined as the ratio of phonon energy detected by the sensitive target element to the incident energy deposited in the substrate. This work simulates the phonon collection efficiency for two existing detector architectures to study phonon absorption at substrate-sensor interfaces and phonon loss to non-sensitive detector elements.

Dang, Stella Q.↗
DOE OSTI2025

Statistical distributions for transient transport

Here, this paper introduces the use of statistical distributions based on transport differential equations for clear distinction of transport modes within transient kinetic experiments. More specifically, novel techniques are developed for the transient data obtained through the Temporal Analysis of Products (TAP) reactor and are applicable to experiments where pulse response into a gas flow is used. The methodology allows distinguishing between two domains of diffusion transport in heterogeneous catalytic systems, i.e., Knudsen and non-Knudsen diffusion, using statistical fingerprints, and finding the transition domain. Two distribution parameters were obtained that directly result in coefficients that correspond to the concentration and the rate of transport. Using a linear relationship between the rate and concentration coefficients, Knudsen diffusion is revealed when the rate of transport is constant and non-Knudsen diffusion is confirmed when the rate of transport coefficient is a function of the concentration coefficient. As a result, accurate transport information can be extracted from experimental data even in the presence of comprising instrument drift or noise particularly when analyzing higher pressure pulse responses with complex transport. This enables more direct investigation of experiments influenced by gas-phase reactions.

TAP reactor↗
DOE OSTI2021

Implicit highly-coupled single-ion Hall-MHD formulation for hybrid particle-in-cell codes

The rudiments of a particle-based single-fluid two-temperature magnetohydrodynamic (MHD) algorithm have been outlined in Thoma et al. (2013). The extension of this algorithm to include the effect of Hall physics is described in this paper. An implicit leapfrog version of the algorithm, which allows timesteps large compared to the resistive decay time and other relevant timescales, has recently been added to a hybrid particle-in-cell code. In standard MHD the Hall term in the generalized Ohm’s law can often be neglected when the Hall parameter is small. This term must, however, be retained in regimes where it is non-negligible. The retention of displacement current in Maxwell’s equations avoids the numerical difficulties associated with the whistler mode, which are encountered in standard explicit Hall-MHD codes, and allows the algorithm to be incorporated into hybrid particle-in-cell codes, for which particles may migrate from a kinetic to fluid to MHD description based upon local ambient plasma conditions. A highly-coupled implicit Hall-MHD formalism is presented, in which displacement current can either be retained or neglected. Even when displacement current is neglected, the highly-coupled implicit formalism avoids the restrictive timesteps for the whistler mode in explicit Hall-MHD codes. A comparison of numerical and analytic dispersion analysis demonstrates the feasibility of this approach and establishes relevant constraints to assure numerical stability. The implementation of the algorithm is described, and test simulation results in 1D and 2D in both linear and nonlinear regimes are presented.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2023

Development of a Reactive Force Field for Simulating Photoinitiated Acrylate Polymerization

Light-driven and photo-curable polymer based additive manufacturing (AM) has enormous potential due to its excellent resolution and precision. Acrylated radical chain-growth polymerized resins are widely used in photopolymer AM due to their fast kinetics, and often serve as a departure point for developing other resin materials for photopolymer-based AM technologies. For successful control of the photopolymer resins, the molecular basis of the acrylate free-radical polymerization has to be understood in detail. We present an optimized reactive force field (ReaxFF) for molecular dynamics (MD) simulations of acrylate polymer resins that captures radical polymerization thermodynamics and kinetics. The force field is trained against an extensive training set including density functional theory (DFT) calculations of reaction pathways along the radical polymerization from methyl acrylate to methyl butyrate, bond dissociation energies, and structures and partial charges of several molecules and radicals. We also found that it was critical to train the force field against an incorrect, nonphysical reaction pathway observed in simulations that used parameters not optimized for acrylate polymerization. As a result, the parameterization process utilizes a parallelized search algorithm, and the resulting model can describe polymer resin formation, crosslinking density, conversion rate, and residual monomers of the complex acrylate mixtures.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Bayesian Learning of Adatom Interactions from Atomically Resolved Imaging Data

Atomic structures and adatom geometries of surfaces encode information about the thermodynamics and kinetics of the processes that lead to their formation, and which can be captured by a generative physical model. In this work, we develop a workflow based on a machine-learning-based analysis of scanning tunneling microscopy images to reconstruct the atomic and adatom positions, and a Bayesian optimization procedure to minimize statistical distance between the chosen physical models and experimental observations. We optimize the parameters of a 2- and 3-parameter Ising model describing surface ordering and use the derived generative model to make predictions across the parameter space. For concentration dependence, we compare the predicted morphologies at different adatom concentrations with the dissimilar regions on the sample surfaces that serendipitously had different adatom concentrations. The proposed workflow can be used to reconstruct the thermodynamic models and associated uncertainties from the experimental observations of materials microstructures. The code used in the manuscript is available at https://github.com/saimani5/Adatom_interactions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Time-resolved site-selective imaging of predissociation and charge transfer dynamics: the CH 3 I B-band

The predissociation dynamics of the 6s (B 2 E) Rydberg state of gas-phase CH 3 I were investigated by time-resolved Coulomb-explosion imaging using extreme ultraviolet (XUV) free-electron laser pulses. Inner-shell ionization at the iodine 4d edge was utilized to provide a site-specific probe of the ensuing dynamics. The combination of a velocity-map imaging (VMI) spectrometer coupled with the pixel imaging mass spectrometry (PImMS) camera permitted three-dimensional ionic fragment momenta to be recorded simultaneously for a wide range of iodine charge states. In accord with previous studies, initial excitation at 201.2 nm results in internal conversion and subsequent dissociation on the lower-lying A-state surface on a picosecond time scale. Examination of the time-dependent yield of low kinetic energy iodine fragments yields mechanistic insights into the predissociation and subsequent charge transfer following multiple ionization of the iodine products. The effect of charge transfer was observed through differing delay-dependencies of the various iodine charge states, from which critical internuclear distances for charge transfer could be inferred and compared to a classical over-the-barrier model. Time-dependent photofragment angular anisotropy parameters were extracted from the central slice of the Newton sphere, without Abel inversion, and highlight the effect of rotation of the parent molecule before dissociation, as observed in previous works. Our results demonstrate the ability to perform three-dimensional ion imaging at high event rates and showcase the potential benefits of this approach, particularly in relation to further time-resolved studies at free-electron laser facilities.

74 ATOMIC AND MOLECULAR PHYSICS↗
DOE OSTI2023

High-pressure CO 2 dissociation with nanosecond pulsed discharges

Herein we investigate the conversion of CO 2 into CO and O 2 with nanosecond repetitively pulsed (NRP) discharges in a high-pressure batch reactor. Stable discharges are obtained at up to 12 bar. By-products are measured with gas chromatography. The energy efficiency is determined for a range of processing times, pulse energy, and fill pressures. It is only weakly sensitive to the plasma operating parameters, i.e the extent of CO 2 conversion is almost linearly-dependent on the specific energy invested. A conversion rate as high as 14% is achieved with an energy efficiency of 23%. For long processing times, saturation in the yield and a drop in efficiency are observed, due to the increasing role of three-body recombination reactions, as described by zero-dimensional detailed kinetic modeling. The modeling reveals the presence of three-stage kinetics between NRP pulses, controlled by electron-impact CO 2 dissociation, vibrational relaxation, and neutral elementary kinetics. Transport effects are shown to be important for CO 2 conversion at high pressures. For fill pressures beyond 10 bar, CO 2 may locally transit into supercritical states. The supercritical plasma kinetics may bypass atomic oxygen pathways and directly convert CO 2 into O 2 . This work provides a detailed analysis of plasma-based high-pressure CO 2 conversion, which is of great relevance to future large-scale sustainable carbon capture, utilization, and storage.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Toward UV models of kinetic mixing and portal matter. V. Indirect probes of the new physics scale

Kinetic mixing of the dark photon, the gauge boson of a hidden U ( 1 ) D , with the Standard Model (SM) gauge fields to induce an interaction between ordinary matter and dark matter (DM) at 1-loop requires the existence of portal matter (PM) fields having both dark and SM charges. As discussed in earlier work, these same PM fields can also lead to other loop-level mechanisms besides kinetic mixing that can generate significant interactions between SM fermions and the dark photon in a manner analogous to those that can be generated between a Dirac neutrino and a SM photon, i.e., dark moments. In either case, there are reasons to believe, e.g., due to the renormalization group equation running of the U ( 1 ) D gauge coupling, that PM fields may have ∼ TeV -scale masses that lie at or above those directly accessible to the HL-LHC. If they lie above the reach of the HL-LHC, then the only way to possibly explore the physics at this high scale in the short term is via indirect measurements made at lower energies, e.g., at lepton colliders operating in the m Z to 1 TeV range. In particular, processes such as e + e − → γ + DM or e + e − → f ¯ f , where f is a SM fermion, may be most useful in this regard. Here we explore these possibilities within the framework of a simple toy PM model, introduced in earlier work, based on a non-Abelian dark gauge group completion operating at the PM scale. In the kinetic mixing setup, we show these efforts fail due to the inherently tiny cross sections in the face of substantial SM backgrounds. However, in the case of interactions via induced dark moments, since they necessarily take the form of higher dimensional operators whose influence grows with energy, we show that access to PM-scale information may become possible for certain ranges of the toy model parameters for both of these e + e − processes at a 1 TeV collider. Published by the American Physical Society 2024

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗