Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “idaho”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 991 records · Page 55
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Flow friction in a wide rectangular duct with a beveled inlet: Informal Notes of Fundamental Fluid Physics Studies

Fundamental streamwise pressure distributions were measured at Idaho State University to address a primary objective of obtaining insight into the apparent evolution of air flow regimes at moderate Reynolds numbers in thin, wide rectangular ducts with converging inlets. Ducts of 3.030 and 4.077 mm spacings s (called three and four mm), having non-dimensional lengths of (L/s) ≈ 500.8 and 372.2 and widths (W/s) ≈ 114.6 and 83.2, respectively, were compared. Flow rates ranged from Reynolds numbers based on hydraulic diameter (Re Dh ) of about 980 to 10,000 and corresponding non-dimensional downstream pressure gradient parameters (-K p ) covered the range 0.038 to 0.0061, respectively.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2024

Assessment of Potential Dose and Environmental Impacts from Proposed Testing at the INL Radiological Response Training Range

This assessment uses screening level models to calculate potential environmental impacts from proposed tests at the Idaho National Laboratory (INL) Radiological Response Training Range (RRTR) site. Proposed tests could be conducted using 11 different radioactive material types that include K 2 O, LaBr 3 , KBr, Cu, Zr, F, Ga, Ga 2 O 3 , NaNO 2 , Ga-68, and Tc-99m. The tests could potentially release radioactive material to the atmosphere and radionuclides and other contaminants to the soil, which could leach into the unsaturated zone and migrate to the aquifer. Atmospheric transport of radionuclides to potential human receptors and time-integrated air concentrations were calculated with a Gaussian plume model and three years of hourly meteorological data. Potential surface-soil impacts were calculated with the computer program Mixing-Cell Model (MCM). Groundwater impacts were calculated with the computer programs MCM and GWSCREEN. Radiological doses from potential atmospheric releases were calculated for public receptors off the INL Site and for workers at nearby INL facilities. Results were compared to regulatory dose limits. Maximum potential groundwater concentrations were estimated in the aquifer below the NSTR site and compared to drinking water standards or risk-based screening levels for resident tap water. Soil concentrations were calculated and compared to risk-based screening levels for workers and potential future residents. All impacts were estimated based on the assumption that 12 tests are conducted annually using all 11 material types for a period of 15 years. This document provides the resources to enable a subject matter expert in the field of environmental assessments to replicate the modeling and calculations. The methodology and parameters are presented in the text. All electronic files, including computer code input, output, executable files, batch files, scripts, and spreadsheet files are contained in a zip file that can be accessed by selecting “Additional Information” (select Native File) in the INL Electronic Document Management System (EDMS).

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2024

Assessment of Potential Dose and Environmental Impacts from Proposed Testing at the INL National Security Test Range

This assessment uses screening level models to calculate potential environmental impacts from proposed tests at two locations at the Idaho National Laboratory (INL) National Security Test Range (NSTR) site. Proposed tests could be conducted using 11 different radioactive material types that include K 2 O, LaBr 3 , KBr, Cu, Zr, F, Ga, Ga 2 O 3 , NaNO 2 , Ga-68, and Tc-99m. The tests could potentially release radioactive material to the atmosphere and radionuclides and other contaminants to the soil, which could leach into the unsaturated zone and migrate to the aquifer. Atmospheric transport of radionuclides to potential human receptors and time-integrated air concentrations were calculated with a Gaussian plume model and three years of hourly meteorological data. Potential surface soil impacts were calculated with the computer program Mixing-Cell Model (MCM). Groundwater impacts were calculated with the computer programs MCM and GWSCREEN. Radiological doses from potential atmospheric releases were calculated for public receptors off the INL Site and for workers at nearby INL facilities. Results were compared to regulatory dose limits. Maximum potential groundwater concentrations were estimated in the aquifer below the NSTR site and compared to drinking water standards or risk-based screening levels for resident tap water. Soil concentrations were calculated and compared to risk-based screening levels for workers and potential future residents. All impacts were estimated based on the assumption that 12 tests are conducted annually using all 11 material types for 15 years. This document provides the resources to enable a subject matter expert in the field of environmental assessments to replicate the modeling and calculations. The methodology and parameters are presented in the text. All electronic files, including computer code input, output, executable files, batch files, scripts, and spreadsheet files, are contained in a zip file that can be accessed by selecting “Additional Information” (select Native File) in the INL Electronic Document Management System (EDMS).

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2024

Sodium-Cooled Fast Reactor Reference Plant Model

This report details the progress of Idaho National Laboratory (INL) in creating a reference plant multiphysics model for the Advanced Burner Test Reactor (ABTR). This model was developed under Task 13 of the U.S. Nuclear Regulatory Commission project “Development and Modeling Support for Advanced Non-Light Water Reactors,” and is an extension of the reference plant model developed in Task 4b, which was improved upon in the following ways. (1) The discrete ordinates method was used in lieu of the super-homogenization (SPH)-corrected diffusion approximation in order to better capture the anisotropic scattering contribution and the neutron leakage change due to thermal expansion. (2) The novel neutronic spatial discretization approach, termed the ring-heterogeneous (RH) approximation, was conceptualized and introduced to capture the differential expansion of the materials in the core. This new technique proved capable of preserving fission rates and maintaining the eigenvalue within 2.5% and 266 pcm with 9 neutron energy groups, respectively. Separating the different materials in the core enables the differential expansion of materials to be explicitly accounted for, eliminating the need for problem-specific cross-section functionalization techniques. (3) The SAM model for the core and system thermal-hydraulics analysis was updated to include 61 channels instead of just four representative ones. This enables users to obtain improved spatial resolution for sodium temperature and density scalar fields. (4) All the mesh files were created via the Multiphysics Object-Oriented Simulation Environment (MOOSE) Reactor module, eliminating all reliance on external tools for mesh creation. (5) Finally, the fuel axial expansion now leverages the HT9 and UPuZr material properties that have been validated against experimental data. The reference plant model was used to perform a full-core unprotected loss of flow (ULOF) transient calculation, including neutronics, thermal and mechanical feedback mechanisms. Future work will be devoted to further enhancements of the model. Potential improvements to the model include the addition of the control rod driveline expansion feedback and the upgrading of the support plate model so as to explicitly include 3D effects. Additionally, a Nuclear Energy Advanced Modeling and Simulation funded parallel effort has completely automated the creation of the ring-heterogeneous (RH) mesh from the fully heterogeneous (FH) geometry, thus maximizing user friendliness for the sodium fast reactor sodium-cooled fast reactor (SFR) workflow and will be incorporated in future work.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2024

Baseline Characterization Database Verification Report - NBG-18 Billet 635-14

The purpose of this Engineering Calculations and Analysis Report is to present the data being collected in the Baseline Graphite Characterization program, which is directly tasked with supporting the Idaho National Laboratory’s (INL’s) research and development efforts on the Next Generation Nuclear Plant (NGNP)/Very High Temperature Reactor (VHTR)/Advanced Reactor Technology (ART). This program is populating a comprehensive database that will reflect the baseline properties of nuclear-grade graphite regarding individual grade, billet, and position within individual billets. The physical and mechanical property information being collected will be transferred to the NGNP Data Management and Analysis System (NDMAS), and from that database will help populate handbook of property data available to member nations of the Generation IV International Forum (GIF).

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Development Plan for Acoustic Emission and Vibration Sensors

This document discusses the need for high temperature, radiation tolerant sensors for monitoring vibration and acoustic emissions in advanced reactors and irradiation experiments. Testing of several commercial sensors using infrastructure available at Idaho National Laboratory was performed to benchmark currently available sensors as well as the test facilities. Finally, a strategy for developing sensors for more extreme environments is presented.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2022

Alternate Methods for Cleaning Zirconium Plate

The United States High Performance Research Reactor Conversion Program identified the need to transition from highly enriched uranium fuel to lowly enriched uranium fuel for high power research and civil reactors. One of the fuel configurations selected for these reactors was a uranium (U) foil alloyed with 10% molybdenum (Mo). The U-10Mo fuel foil was then covered with a zirconium (Zr) interlayer and pressed into an aluminum cladding. Idaho National Laboratory prescribed a need to remove surface oxidation on the Zr prior to bonding it with U-10Mo fuel foil. To determine the best method of oxidation removal, a variety of polishing methods, including hand polishing with a diamond paste or Scotch-Brite™ pads, mechanically wet-polishing with abrasive belts, and chemical etching with hydrofluoric/nitric acid mixtures, were investigated on pre-polished Zircaloy 702 sheets purchased directly from the manufacturer. No change in surface roughness was detected using any of these methods relative to the as-received material. In fact, scanning electron microscopy detected grit from hand polishing with Amplex Grade 30 waste soluble diamond paste and Scotch-Brite™ pads. Visible staining was found, and fluorine detected via X-ray photoelectron spectroscopy on the flash etching samples. These contaminants were not seen on the as-received material. In addition to the need to remove the oxide layer on the Zr prior to co-rolling, there are concerns that the Neolube debonding agent on the co-rolling can may contaminate the Zr surface after co-rolling. The experimental results found that zirconium in contact with Neolube coated steel plates was easily cleaning with ethanol wiping after heat treated and no carbide inclusions remained on the surface. Overall, all cleaning methods tested did not significantly change the surface roughness of the plates or reduce the oxide layer present on the zirconium. Carbon was found on all the samples, before and after cleaning, except for the flash etch samples which detected fluorine instead. The insignificant changes seen in the cleaned plates relative to the as received plates question the need for cleaning prior to rolling. Further investigation in the requirements for cleaning at this step is recommended. Current methods for cleaning the surface after hot rolling with alcohol appear sufficient. After hot rolling, if Neolube does peel off the can and onto the zirconium coated foil surface, a dry abrasive or diamond paste polish is not recommended due to the chance of abrasive being embedded into the surface. However, the ability of an etchant to lift the lubricant off the zirconium surface indicates that a spot etch method could work to clean specific spots where Neolube is present, if the need arises.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

MARVEL Reactor Fuel Performance Report (Rev.2)

The Microreactor Applications Research Validation and EvaLuation (MARVEL) project is producing a high temperature liquid metal-cooled nuclear test bed at Idaho National Laboratory (INL) to ultimately improve the integration of microreactors to end-user applications. This ambitious effort seeks to design, authorize, construct, test, and operate the reactor within five years. In order to construct and operate the MARVEL reactor in a timely manner, the system will utilize materials and component designs which have already been used, qualified, or licensed from previous reactors. The MARVEL reactor will be located at the INL Transient Reactor Test (TREAT) facility in the north high-bay equipment pit and will use the existing 304 stainless steel-clad U-ZrH1.6 pin-type fuel system developed by General Atomics and purchased from TRIGA International. This fuel has been previously qualified under the United States Department of Energy’s (US DOE) Reduced Enrichment for Research and Test Reactors (RERTR) Program. Even though the regulator of the MARVEL reactor is the US DOE, the standards and overall approach recommended by the Nuclear Regulatory Commission is well-defined and utilized here. Following NUREG-1537 regulatory guidance, this report documents the authorization case for the MARVEL fuel system’s application to MARVEL and establishes stable and predictable fuel performance during the most thermophysically unfavorable conditions achievable in the MARVEL reactor. To that end, this report provides a comprehensive survey of the known thermophysical properties, performance, and quantitative relationships associated with the MARVEL reactor fuel element and uses this information to determine its mechanical integrity and risk of reaching unacceptable conditions during the most extreme accident scenarios predicted for the reactor using the most conservative assumptions available. The information contained herein is compiled from a combination of historical reports and peer reviewed scientific publication manuscripts. Known mechanisms under which the fuel is susceptible to failure are highlighted and compared to conditions that could exist in the MARVEL reactor during an unanticipated transient or accident scenario. The two scenarios considered for analysis in this report are (1) an unprotected loss of flow accident and (2) a hypothetical unprotected loss of coolant accident during the loss of flow accident. Preliminary 2D steady-state analyses herein indicate that both fuel-cladding chemical interactions and fuel-cladding mechanical interactions are negligible throughout the fuel’s operational cycle under both normal and high temperature accident scenario conditions. Although higher fidelity 3D time-dependent modeling and simulations are planned, the following may be concluded presently. The MARVEL fuel element maintains its geometric stability and structural integrity during the most extreme accident scenarios predicted for the MARVEL reactor. The hoop stress during the unprotected loss of flow accident reaches about -1.27 MPa; this negative stress indicates that it is compressive rather than tensile. The compressive stress is a result of the NaK pressure on the outside of the fuel element, caused by the restricted thermal expansion of the NaK coolant, exceeding the internal pressures generated inside of the fuel element. The hoop stress generated in the cladding during the unprotected loss of coolant accident reaches a maximum of about approximately 10 MPa, which is nearly an order of magnitude less than the predicted yield strength of the cladding under high-temperature accident scenario conditions. Calculations were compared with results from high performance computational simulations using BISON and are in very close agreement. A conservative MARVEL fuel meat peak temperature limit of 900 °C is recommended presently, which is about 180 °C higher than the peak fuel temperature predicted to occur during the most extreme accident. Based on the known properties and behavior of the MARVEL fuel element, the fuel successfully meets its design and safety requirements under normal and most extreme accident conditions with a large safety margin.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Prioritization of Existing Reactor Materials

The Advanced Materials and Manufacturing Technologies (AMMT) Program is aiming at the faster incorporation of new materials and manufacturing technologies into complex nuclear-related systems. An integrated approach, combining advanced characterization, high-throughput and accelerated testing, modeling and simulation, including machine learning and artificial intelligence, will be employed. Although 316H (Fe–[16–18]Cr–[10–14]Ni–[2–3]Mo–[0.04–0.1]C) has been identified as a key alloy to be integrated into the AMMT accelerated alloy qualification approach because of its relevance for many current and future nuclear energy reactors, many other alloys could be considered for the advanced fabrication of innovative, high-performance nuclear components. Argonne National Laboratory (ANL), Idaho National Laboratory (INL), Oak Ridge National Laboratory (ORNL), and Pacific Northwest National Laboratory (PNNL) are collaborating on identifying the most promising alloy candidates relevant for the AMMT Program. A selection criteria matrix was established to evaluate the alloys considering their relative importance and technological readiness levels for nuclear energy applications, with a focus on laser powder bed fusion (LPBF). Because of the broad range of potential candidate alloys, ORNL and INL focused on nickel-based alloys, and ANL and PNNL mainly evaluated iron-based alloys. PNNL previously published material scorecards reports on several key alloys, and this report provides a broader overview of iron- and nickel-based candidate alloys, expending beyond alloys well-known to the nuclear community.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2023

Interfacial Engineering and Modeling of High Energy Li Batteries

In the past 6 years, the UW team have collaborated extensively with the Battery500 Consortium team members, including The Pacific Northwest National Lab, The Idaho National Lab, Binghamton University, and UT Austin. We have accomplished all milestones and deliverables at the end of the program.

25 ENERGY STORAGE↗
DOE OSTI2024

ORNL Peer Review Summary and Recommendations for: Advanced Reactor Designs Security Analysis, Risk, and Recommendations: Risks, Consequences, and Possible Design Mitigation Approaches Associated with Select Advanced Reactors Study

The purpose of this document is to provide a summary of the peer review conducted for the "Advanced Reactor Designs Security Analysis, Risk, and Recommendations: Risks, Consequences, and Possible Design Mitigation Approaches Associated with Select Advanced Reactors" study prepared by researchers at Idaho National Laboratory (INL), Argonne National Laboratory (ANL), and Oak Ridge National Laboratory (ORNL). The National Nuclear Security Administration (NNSA) International Nuclear Security (INS) program team requested that ORNL perform a peer review of the study report prior to publication as a final peer check before distributing the report to a broader audience.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2024

Outcomes of HPC User Support using a Science Gateway AI Assistant

High Performance Computing (HPC) is a vital resource for nuclear energy research, facilitating advanced simulations and complex modeling of the quantification and qualification of advanced reactor technology. However, a common gap in knowledge exists around utilizing HPC systems, particularly for nuclear energy researchers unfamiliar with specific HPC systems. A researcher may be well-versed in using one HPC system and understanding its associated processes. Yet, they might struggle when faced with a different HPC system and its unique processes. HPC support staff play a crucial role in addressing these challenges by providing educational resources and assisting users. However, they also face the challenge of maintaining these systems and ensuring they run efficiently for all users, a responsibility that can be challenging to scale effectively with the increasing demand and expansion of HPC systems. This paper addresses this knowledge gap with an artificial intelligence (AI) assistant that offers on-demand, site-specific HPC support for researchers. Idaho National Laboratory (INL) has deployed an AI assistant that is intended to supplement expert HPC support staff and assist nuclear energy researchers. This paper reports on a four-and-a-half-month study evaluating the integration of an AI assistant within a science gateway, with the goal of enhancing existing HPC support.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2023

Improved Fast Reactor Capability of Griffin in FY23

Griffin is a MOOSE based reactor multiphysics analysis application jointly developed by Idaho National Laboratory and Argonne National Laboratory under the DOE-NE NEAMS program. In FY23, we enhanced capabilities required for fast reactor analysis. This effort included primarily updating the cross-section generation workflow using MC2-3 for various reactor configurations, such as homogeneous, duct-heterogeneous, ring-heterogeneous, and fully-heterogeneous geometries. In addition, we initiated the implementation of a multi-cycle depletion and shuffling capability. To support fast reactor simulation capabilities, we significantly improved the performance of the DFEM-SN-based R-Z transport solver to efficiently solve ultrafine group (over 1000 groups) transport problems. Additionally, the performance of HFEM-PN was improved by introducing red-black iteration, the cmfd acceleration technique, and various optimizations. We also completed the pin power reconstruction capability to support multiphysics simulations while identifying and addressing issues associated with SPH equivalence parameter approach. These enhanced capabilities for fast reactor core simulations, specially HFEM-PN and pin power reconstruction features, were applied to benchmark problems involving ABTR and ABR-1000. These applications showcased excellent agreement with Monte Carlo and other code solutions in terms of eigenvalue, control rod worth, and assembly and pin powers.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2020

Coupling of Spark Plasma Sintering with Advanced Modeling to Enable Process Scale-Up: Presentation to DOE-NE [Slides]

The research goal of this project is to develop at Idaho National Laboratory (INL) a first-of-its-kind Multiphysics Object-Oriented Simulation Environment (MOOSE)-based, multiscale, multiphysics spark plasma sintering (SPS) modeling and simulation code application, termed “Freya.” Freya will simulate the thermo-mechanical-electrical aspects of the SPS fabrication process and will be paired with lower length scale sub-models, such as phase-field, to predict the resulting microstructure. SPS is an advanced manufacturing process that can be used to solve a variety of material manufacturing challenges; however, this process is an extremely challenging problem for modeling and simulation. The SPS process is inherently multiphysics and multi-scale, with the macroscale electro-thermo-mechanical behavior linked intricately to the microstructure evolution of the part being sintered. Accurate modeling and simulation tools, specifically geared towards the SPS process, are needed to predict the influence of the multiple variables involved in the manufacturing process. Modeling and simulation accuracy is achieved and demonstrated through comparison to multiple validation experiments. The validation efforts for Freya include both separate effects and complete multiphysics SPS process experiments. One of the key benefits this Laboratory Directed Research & Development (LDRD) project offers stems from the emphasis placed on experimental validation of the Freya models, both on the individual length scales and of the final coupled multiscale multiphysics simulations. Experimental validation of Freya’s multiscale coupling capability provides the technical credibility necessary for potential future industry and research partners to accept the simulation predictions.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Fission Battery Initiative Siting and Transportation Workshop (Summary Report)

This document is a summary report on the Fission Battery (FB) Initiative Siting and Transportation workshop held on March 15, 2021. The workshop was developed by Idaho National Laboratory (INL) in collaboration with INL’s National University Consortium (NUC). One of goals of this workshop was to initiate a conversation between various stakeholders on FBs, focusing on FB transportation and siting. Other goals were sharing the current understanding of the FB concept among the shareholders, identifying FB research and development (R&D) needs, and fostering community building. This report summaries the presentations and conversations held by the subject matter experts (SMEs) and discusses the key findings and conclusions. Further, it provides intermediate recommendations to support R&D in successful FB transportation and siting. The following priority research directions (PRDs) were identified: (i) investigations in the FB source term, (ii) investigations in the FB design, and (iii) investigations in the design of a FB transportation packaging.

42 ENGINEERING↗
DOE OSTI2020

Initial Evaluation of Microreactor Disposition Options

The United States Department of Energy is supporting the U.S advanced reactor industry through funding, legislation and regulatory development to actively pursue several microreactor design concepts. The Idaho National Laboratory (INL) is strategically positioned to support demonstration of microreactor technology in the next three to five years. This report provides and initial evaluation of the disposition options for microreactor spent nuclear fuel (SNF) generated as part of the microreactor technology demonstration program. Currently available information constitutes the basis for the options identified and discussions thereof. In the absence of detailed microreactor design information, assumptions were made to facilitate the identification of disposition options Particulars pertaining to any component of an identified disposition pathway are naturally highly microreactor design specific and in general such details are not provided. The diverse nature of potential microreactor SNF is reflected in the diverse nature of DOE owned SNF stored at INL. Therefore, it is anticipated that DOE currently stores and manages fuels that can serve as analogs for most microreactor fuel concepts. As such disposition options for microreactor SNF are expected to be much the same as that for these existing fuels. Two generic microreactor concepts have been selected for the purposes of this options assessment. The selected reactor concepts are a tristructural isotropic (TRISO) fueled high temperature gas reactor concept and a sodium/potassium bonded heat pipe reactor with uranium oxide fuel. Both concepts are assumed to be using high-assay low enriched uranium (HALEU) as the initial fuel composition. Interim storage, treatment and neutralization, material recovery, packaging and extended dry storage options are identified these reactors. The disposition options include existing INL facilities and capabilities and new facilities and capabilities developed as part of the microreactor program or as part of DOE's overall strategy for the eventual transfer of all SNF at INL to a permanent repository.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Characterization of Mk-IV and EBR-II X441A Metallic Fuel Pins for the THOR-C-2 and THOR-M-TOP-1 Experiments: Results from Post-Transient Neutron Tomography of THOR-C-2 Capsule and Pre-transient Non-Destructive and Destructive Examination of DP 36 and DP 40 (Rev.1)

Current interest in sodium-cooled fast reactor designs, such as TerraPower’s Natrium Reactor, has highlighted the need for advanced-reactor fuel technology development. A Fuel Safety Research and Development (FSRD) program for metallic fast reactor fuels has been created to achieve comprehensive safety testing within the re-commissioned Transient Reactor Test (TREAT) facility at the Idaho National Laboratory. Despite over 60 years of metallic fuel irradiation, uncertainties exist in the performance of the fuel system, particularly under anticipated operational occurrences and severe accident scenarios. Throughout historical testing within the Experimental Breeder Reactor (EBR)-II and the Fast Flux Test Facility, fuel behavior has demonstrated benign response to transient reactor conditions; however, accurate predictions of failure thresholds rely heavily on fuel composition and irradiation history. In advancing the FSRD program, two planned transient heating experiments are at various stages of completion. The Temperature Heat sink Overpower Response (THOR)-C-2, fueled with an unirradiated Mk IV U-10Zr pin, has undergone transient irradiation in TREAT and post-transient three-dimensional neutron tomography. Additionally, pre-transient characterization of test and sibling U-19Pu-10Zr pins for THOR-M-TOP-1 was evaluated by both non-destructive and destructive methods. The test and sibling pins were selected from previously irradiated EBR-II experiment X441A. Both pins underwent visual examination, precise gamma spectrometry, two-dimensional neutron radiography, and element contact profilometry while the sibling pin was additionally subjected to sectioning and optical microscopy. THOR-C-2 radiography captured the fuel and cladding relocation during the intermediate transient at the top and bottom of the THOR capsule, allowing key features to be linked to the pin’s measured thermal response. For THOR M TOP 1, a solid baseline for steady-state behavior has been established. No anomalous features were identified in either the test or sibling pin. Defining characteristics and features were recorded for further comparisons.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2024

BISON: A Flexible Code for Advanced Simulation of the Performance of Multiple Nuclear Fuel Forms [Slides]

As fuel vendors and designers pursue the development of advanced reactors or the increase in burnup limits for existing reactors, advanced computational tools are necessary to understand the fuel performance. BISON, a fuel performance code developed primarily at Idaho National Laboratory, which is built upon the Multiphysics Object-Oriented Simulation Environment (MOOSE), provides capabilities to analyze multiple nuclear fuel forms in a wide variety of dimensions. Since its inception, BISON has been used to investigate the performance of light-water reactor fuel rods, accident tolerant fuel concepts, metallic and mixed-oxide (MOX) fuels for fast reactors, plate fuels for research reactors, and tri-structural isotropic (TRISO) fuel particles. This talk will provide a history of BISON, highlights of major development milestones, tributes to key contributors, and applications of its use to various fuel forms in one-, two-, and three-dimensions.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗