Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “heterogeneous materials”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 991 records · Page 55
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

In-situ re-crystallization of heavily-irradiated Gd 2 Ti 2 O 7

Gadolinium titanate (Gd 2 Ti 2 O 7 , or GTO) and other lanthanide pyrochlores are interesting candidates for actinide waste disposal and fast ion conduction because the relevant material properties are intimately dependent on local cation structure. Therefore, a deep understanding of the kinetics associated with cation ordering and disordering is required if such material properties are to be tuned for specific device designs. To this end, single crystals of GTO were irradiated with 190 keV helium ions to a total fluence of 1 × 10 17 ions/cm 2 , amorphizing the sample surface to a depth of ~1 μm and resulting in significant He bubble accumulation. FIB lamellae lifted out from the irradiated sections were examined during heat treatment in the (scanning) transmission electron microscope. Two distinct stages of the re-crystallization of the amorphized material were observed. The material near the end of the ions’ range transformed first and with the same orientation as the pristine material. This was due to the close proximity of the pristine material and the presence of small defect fluorite seeds, but the propagation of this growth front was frustrated by the large pores (formerly bubbles) in the He accumulation layer. This was followed by heterogeneous nucleation of new crystallites at random orientations at the top of the He accumulation layer, which is attributed to the high surface area associated with the many small He bubbles in that region. Finally, it is inferred that the kinetics of grain growth in this material are significantly faster than the kinetics of grain nucleation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Two-Factor Phase Separations in Mixed-Halide Quasi-2D Perovskite LEDs: Dimensionality and Halide Segregations

Quasi-2D halide perovskites have attracted much interest as a promising material for light-emitting diodes (LEDs) due to their tunability in quantum confinement and halide alloy formation to modulate the energy bandgap and emission color. However, two-factor phase separations with respect to heterogeneous quantum-well thicknesses and halide segregation are still crucial issues in quasi-2D perovskite LEDs, leading to low external quantum efficiencies (EQEs) and color shifts. In this work, we compare quasi-2D perovskite films using different cations to unveil the key contributions from the chemical design of organic cations. While mixing halide ions in conventional quasi-2D perovskite films induces micrometer-scale heterogeneity, new extended and twisted conjugated cations suppress the two-factor phase separations, leading to high EQEs of over 25% and controllable emission wavelengths across red and near-infrared regions. The fundamental insights in this work will provide guidance for advancing materials design and device performance in the future.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1979

Heterogeneous atmospheric reactions - Sulfuric acid aerosols as tropospheric sinks

The reaction probabilities of various atmospheric species incident on a bulk sulfuric acid surface are measured in order to determine the role of sulfuric acid aerosols as pollutant sinks. Reaction products and unreacted starting materials leaving a Knudsen cell flow reactor after collision at 300 K with a H2SO4 surface or a soot surface were detected by mass spectrometry. Significant collision reaction probabilities are observed on a H2SO4 surface for H2O2, HNO3, HO2NO2, ClONO2, N2O5, H2O and NH3, and on soot for NH3. Estimates of the contribution of heterogeneous reactions to pollutant removal under atmospheric conditions indicate that while aerosol removal in the stratosphere is insignificant (loss rate constants approximately 10 to the -10th/sec), heterogeneous reactions may be the dominant loss process for several tropospheric species (loss rate constant approximately 10 to the -5th/sec, comparable to photolysis rate constants).

Baldwin, A. C.↗
DOE OSTI2025

Measuring the flatband potential in 2D semiconductors: Pitfalls and a possible SECCM solution

The flatband potential (V fb ) is a critical parameter in semiconductor electrochemistry, defining the potential at which no excess charge exists at the semiconductor/electrolyte interface. It serves as a key reference for interpreting charge transfer kinetics and current–voltage behavior. However, conventional methods like Mott–Schottky analysis fail for atomically thin 2D materials due to the breakdown of the depletion approximation. This perspective examines the limitations of traditional V fb measurements for 2D semiconductors and the experimental challenges that arise. To address these issues, we propose using scanning electrochemical cell microscopy (SECCM) to spatially resolve the potential of zero charge (V pzc ), equivalent to V fb . This approach mitigates sample heterogeneity issues, such as pinholes or multilayer defects, and offers a pathway to more accurate electrochemical characterization. Ultimately, this method will enhance understanding of current–potential behavior in 2D materials, supporting the design of advanced systems for photoelectrocatalysis, energy conversion, and sensing.

2D semiconductors↗
DOE OSTI2022

Critical length scales for chemical heterogeneity at Cu/Nb 3D interfaces by atom probe tomography

Cu/Nb nanocomposites containing sharp, two-dimensional (2D) interfaces have outstanding strength but limited deformability. In contrast, Cu/Nb with three dimensional (3D) biphase interfaces exhibiting crystallographic, topological, and chemical variations in all spatial dimensions overcomes this limitation by simultaneously enhancing material strength and deformability. Here, while structural characterization of 3D interfaces has been performed to understand their mechanical behavior, three dimensional chemical characterization of such interfaces is lacking. In this work we quantify the local chemistry of 3D interfaces in Cu/Nb nanocomposites using atom probe tomography (APT). Our analysis demonstrates chemical heterogeneities along all spatial dimensions in 3D interfaces, establishes the length scale of such features, and quantifies the morphology of 3D interfaces. 3D interface heterogeneities form by surface diffusion during physical vapor deposition (PVD), suggesting that deposition parameters can be used to control interface structure and provide unique ways to explore processing-structure-property relationships in interface-dominated nanocomposites.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Probing Dopant Redistribution, Phase Propagation, and Local Chemical Changes in the Synthesis of Layered Oxide Battery Cathodes

Achieving the targeted control of layered oxide properties calls for more fundamental studies to mechanistically probe their evolution during their synthesis. Herein, dopant distribution, phase propagation, and local chemical changes as well as their interplay in multielement-doped LiNiO 2 materials are investigated using spectroscopic, imaging, and scattering techniques. It is shown that dopants undergo dynamic redistribution in the Ni(OH) 2 host lattice at the early stage of calcination (below 300 °C). Such redistribution behavior exhibits strong dopant-dependent characteristics, allowing for targeted surface and bulk doping control. The Ni oxidation process exhibits depth-dependent characteristics and the most rapid Ni oxidation takes place between 300 and 700 °C. Using Ni oxidation state as the proxy for the phase transformation, the buildup of heterogenous phase propagation in the early stage of calcination is shown, especially along the radial direction of secondary particles. Furthermore, the radial heterogenous phase distribution gradually decreases upon completing the calcination. However, a high degree of mosaic-like heterogeneity may still be present in the final product, departing from the perfect layered oxide. Overall, the present study offers fundamental insights into manipulating multiscale materials properties during calcination for obtaining stable, high-energy layered oxide cathodes.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Chemical composition of material extractives influences microbial growth and dynamics on wetted wood materials

The impact of material chemical composition on microbial growth on building materials remains relatively poorly understood. We investigate the influence of the chemical composition of material extractives on microbial growth and community dynamics on 30 different wood species that were naturally inoculated, wetted, and held at high humidity for several weeks. Microbial growth was assessed by visual assessment and molecular sequencing. Unwetted material powders and microbial swab samples were analyzed using reverse phase liquid chromatography with tandem mass spectrometry. Different wood species demonstrated varying susceptibility to microbial growth after 3 weeks and visible coverage and fungal qPCR concentrations were correlated (R 2 = 0.55). Aspergillaceae was most abundant across all samples; Meruliaceae was more prevalent on 8 materials with the highest visible microbial growth. A larger and more diverse set of compounds was detected from the wood shavings compared to the microbial swabs, indicating a complex and heterogeneous chemical composition within wood types. Several individual compounds putatively identified in wood samples showed statistically significant, near-monotonic associations with microbial growth, including C 11 H 16 O 4 , C 18 H 34 O 4 , and C 6 H 15 NO. A pilot experiment confirmed the inhibitory effects of dosing a sample of wood materials with varying concentrations of liquid C 6 H 15 NO (assuming it presented as Diethylethanolamine).

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2021

Study of an Integration Platform Based on an Adiabatic Active-Layer Waveguide Connection for InP Photonic Device Integration Mirroring That of Heterogeneous Integration on Silicon

In this work, a photonic device integration platform capable of integration of active-passive InP-based photonic devices without the use of material regrowth is introduced. The platform makes use of an adiabatic active-layer waveguide connection (ALWC) to move an optical beam between active and passive devices. The performance of this platform is analyzed using an example made up of four main sections: (1) a fiber coupling section for enabling vertical beam coupling from optical fiber into the photonic chip using a mode-matched surface grating with apodized duty cycles; (2) a transparent waveguide section for realizing passive photonic devices; (3) an adiabatic mode connection structure for moving the optical beam between passive and active device sections; and (4) an active device section for realizing active photonic devices. It is shown that the coupled surface grating, when added with a bottom gold reflector, can achieve a high chip-to-fiber coupling efficiency (CE) of 88.3% at 1550 nm. The adiabatic active-layer mode connection structure has an optical loss of lower than 1% (CE > 99%). The active device section can achieve an optical gain of 20 dB/mm with the use of only 3 quantum wells. The optimized structural parameters of the entire waveguide module are analyzed and discussed.

42 ENGINEERING↗
NASA NTRS1984

Velocities of guided ultrasonic waves in heterogeneous medium

Experimental and theoretical examinations were performed of the longitudinal velocity characteristics of waves in trilaminar and encapsulated waveguides. The study was confined to waveguides with core material that featured transverse wave velocities much worse than the longitudinal wave velocities. The velocities were obtained using a dispersion equation, with consideration given to both the core and encapsulant. Asymptotic velocities were also calculated for bending and twisting in trilaminar waveguides. Trials were run with bimetallic waveguides for comparison with the theoretical predictions. Good agreement was found between the predicted velocity of the propagation of the fundamental mode and the measured velocities. The method was calculated valid for modes above four, confirming that the data were contained in either the core or outer layer, and were unsensitive to the encapsulant.

Touratier, M.↗
DOE OSTI2024

Tuning Exciton Emission via Ferroelectric Polarization at a Heterogeneous Interface between a Monolayer Transition Metal Dichalcogenide and a Perovskite Oxide Membrane

Here we demonstrate the integration of a thin BaTiO 3 (BTO) membrane with monolayer MoSe 2 in a dual gate device that enables in-situ manipulation of the BTO ferroelectric polarization with a voltage pulse. While two-dimensional (2D) transition metal dichalcogenides (TMDs) offer remarkable adaptability, their hybrid integration with other families of functional materials beyond the realm of 2D materials has been challenging. Released functional oxide membranes offer a solution for 2D/3D integration via stacking. 2D TMD excitons can serve as a local probe of the ferroelectric polarization in BTO at a heterogeneous interface. Using photoluminescence (PL) of MoSe 2 excitons to optically readout the doping level, we find that the relative population of charge carriers in MoSe 2 depends sensitively on the ferroelectric polarization. This finding points to a promising avenue for future-generations versatile sensing devices with high sensitivity, fast read-out, and diverse applicability for advanced signal processing.

42 ENGINEERING↗
DOE OSTI2021

Plasma-catalyst modeling for materials selection: challenges and opportunities in nitrogen oxidation

Reliable kinetic models are essential to rationalize observations and to guide the selection of appropriate plasma-catalyst combinations. Kinetic models coupling plasma- and heterogeneous-catalytic-chemistries, however, are primitive. Here, we combine reduced plasma chemistries and density functional theory parameterized surface reactions to model NO formation from N2 oxidation, an alternative nitrogen fixation process. We first show plasma excited species can enhance turnover frequencies of both Pt and Au. The enhancing potential is a function of plasma species and their densities. We then compare NO production between plasma/Pt and plasma/Au with an integral reactor model and explore the dependence of NO production as a function of plasma conditions, reactor configurations and chemical compositions. Plasma/Pt generates more NO than plasma/Au under most thermal and plasma parametric conditions. Plasma/Au outperforms plasma/Pt under high plasma excitations at low temperatures. Furthermore, these results highlight that selection of plasma-catalyst combinations should consider the properties of plasmas, materials and the coupling of the two.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Corrosion Testing Of Additively Manufactured Stainless Steel 316H In Molten Salt Environments

The development of a new ASTM standard for evaluating the corrosion resistance of additive manufactured (AM) stainless steel (SS) 316H in chloride molten salts is critical for the use of these materials in extreme environments such as molten salt reactors (MSRs). This report pertains to a work package of the Advaned Materials and Manufacturing Technologies (AMMT) developing a systematic methodology to link changes in AM fabrication parameters, namely surface finishing, porosity, microstructure, and chemical heterogeneity, to corrosion performance in NaCl-MgCl2 salt, a proposed secondary coolant for MSRs. During Fiscal Year 2024, Idaho National Laboratory investigators in the AMMT program, utilized SS316H bars, fabricated with laser bed powder fusion at Los Alamos National Laboratory, to establish and optimize the workflow for evaluating these process-to-performance relationships. Standard practices for specimen preparation were established using these specimens, with particular focus on descaling and sectioning methods that align with ASTM guidelines. A comprehensive experimental design for static corrosion testing was developed, with pre- and post-exposure analysis utilizing optical microscopy and scanning electron microscopy. So far standard descaling techniques were optimized, one static corrosion test was conducted on the LANL AM SS316H specimens, and pre- and post-corrosion practices were established. In addition, the work package yielded a review paper on corrosion testing gaps for AM materials in nuclear applications and submitted a proposal for a rapid-turnaround experiment to the Nuclear Science User Facilities Program to investigate the combined effects of proton irradiation and corrosion on AM SS316H. This work package establishes a foundation for evaluating processing-to-performance relationships for AM SS316H in harsh conditions, contributing to the safe and efficient design of components for next-generation nuclear reactors. The creation of a standardized methodology and the generation of relevant publications and future research pathways represent significant strides towards integrating AM materials into critical applications where corrosion resistance is paramount.

36 MATERIALS SCIENCE↗
DOE OSTI2024

UQ4QM: Uncertainty Quantification for Quantum Materials (Chemical Dynamics Initiative Final Report)

The Uncertainty Quantification for Quantum Materials (UQ4QM) LDRD project focused on developing solutions for strategic two project areas the Chemical Dynamics Initiative (CDi) Use Case 3. This included data-driven approaches toward understanding heterogeneous data, such as multi-fidelity data or data with unknown spatial or temporal perturbations. The applications were varied but the project aims pursued solutions which were amenable to common UQ approaches in order to maximize impact.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Advanced Materials for Energy-Water Systems: The Central Role of Water/Solid Interfaces in Adsorption, Reactivity, and Transport

The structure, chemistry, and charge of interfaces between materials and aqueous fluids play a central role in determining properties and performance of numerous water systems. Sensors, membranes, sorbents, and heterogeneous catalysts almost uniformly rely on specific interactions between their surfaces and components dissolved or suspended in the water-and often the water molecules themselves-to detect and mitigate contaminants. Deleterious processes in these systems such as fouling, scaling (inorganic deposits), and corrosion are also governed by interfacial phenomena. Despite the importance of these interfaces, much remains to be learned about their multiscale interactions. Developing a deeper understanding of the molecular- and mesoscale phenomena at water/solid interfaces will be essential to driving innovation to address grand challenges in supplying sufficient fit-for-purpose water in the future. In this Review, we examine the current state of knowledge surrounding adsorption, reactivity, and transport in several key classes of water/solid interfaces, drawing on a synergistic combination of theory, simulation, and experiments, and finally, provide an outlook for prioritizing strategic research directions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

A heterogeneously integrated silicon photonic/lithium niobate travelling wave electro-optic modulator

Silicon photonics is a platform that enables densely integrated photonic components and systems and integration with electronic circuits. Depletion mode modulators designed on this platform suffer from a fundamental frequency response limit due to the mobility of carriers in silicon. Lithium niobate-based modulators have demonstrated high performance, but the material is difficult to process and cannot be easily integrated with other photonic components and electronics. In this manuscript, we simultaneously take advantage of the benefits of silicon photonics and the Pockels effect in lithium niobate by heterogeneously integrating silicon photonic-integrated circuits with thin-film lithium niobate samples. We demonstrate the most CMOS-compatible thin-film lithium niobate modulator to date, which has electro-optic 3 dB bandwidths of 30.6 GHz and half-wave voltages of 6.7 V×cm. These modulators are fabricated entirely in CMOS facilities, with the exception of the bonding of a thin-film lithium niobate sample post fabrication, and require no etching of lithium niobate.

42 ENGINEERING↗
DOE OSTI2023

Nanoscale mapping of point defect concentrations with $\mathrm{4D-STEM}$

Vacancies are missing atoms in a crystalline material, and occur both at equilibrium (varying with temperature) and out of equilibrium such as when crystalline materials are damaged with radiation or corrosion. While we know of their importance, particularly regarding diffusive mechanisms, it is not straightforward to experimentally measure their concentration or to visualize them directly. Traditionally, measurements such as positron annihilation spectroscopy and to some degree X-ray diffraction can measure average concentrations, but generally lack the ability to visualize or quantify a heterogenous concentration of vacancies that can occur at the level of individual defects and microstructural features. Here, we present a method to map vacancy concentrations and their distribution using local lattice parameter measurements with a high-resolution electron microscope. Our method utilizes a Au thin film as a model to demonstrate the method via four-dimensional scanning transmission electron microscopy (4D-STEM) by correlating the differences between changes in lattice parameter and the volumetric thermal expansion during in situ heating experiments. The vacancy mapping methodology is also applied to non-equilibrium defects accumulated in pure Al via knock-on electron beam irradiation. Our method demonstrates the ability to map point defect concentrations in heterogeneous systems in situ with nanometer spatial resolution. The result is a technique that can provide direct measurements of vacancy concentrations at the level of individual defects in studies of materials in and out of equilibrium.

36 MATERIALS SCIENCE↗