Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “grain texture”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 991 records · Page 55

Smyer H-Chondrite Impact-Melt Breccia and Evidence for Sulfur Vaporization

Smyer is an H-chondrite impact-melt breccia containing approx.20 vol% 0.5- to 13-mm-thick silicate-rich melt veins surrounding unmelted subrounded chondritic clasts up to 7 cm in maximum dimension. At the interface between some of the melt veins and chondritic clasts, there are troilite-rich regions consisting of unmelted. crushed 0.2- to 140-micron-size angular silicate grains and chondrule fragments surrounded by troilite and transected by thin troilite veins. Troilite fills every available fracture in the silicates. including some as thin as 0.1 microns. Little metallic Fe-Ni is present in these regions: the FeS/Fe modal ratio ranges from -25: 1 to approx.500: 1, far higher than the eutectic weight ratio of 7.5: 1. The texture of these regions indicates that the sulfide formed from a fluid of very low viscosity. The moderately high viscosity (0.2 poise) and large surface tension of liquid FeS, its inability to wet silicate grain surfaces at low oxygen fugacities. and the supereutectic FeS/Fe ratios in the troilite-rich regions indicate that the fluid was a vapor. It seems likely that during the shock event that melted Smyer, many silicates adjacent to the melt veins were crushed. Upon release of shock pressure. some of the troilite evaporated and dissociated. Molecules of S2 were transported and condensed into fractures and around tiny silicate grains: there, they combined with Fe from small adjacent metallic Fe-Ni grains to form troilite. The Ni content at the edges of some of these metal grains increased significantly; Co from these Ni-rich grains diffused into nearby kamacite. Impact-induced S volatilization may have played a major role in depleting the surface of 433 Eros (and other chondritic asteroids) in S.

Rubin, Alan E.↗

Microstructural Stability During Creep Exposure of 9Cr-1Mo Steel Treated at Different Normalization Temperatures

A modified 9Cr-1Mo steel has been exposed to three separate austenitization temperatures, i.e., at 950, 1025, and 1100 °C for normalization. After subsequent tempering at 750 °C, the normalized and tempered samples were creep-tested at temperatures of 550, 600, and 650 °C. The creep strength of the investigated samples was evaluated in terms of minimum creep strain rate and time to rupture. The effects of microstructure, precipitate and boundary misorientation on the creep behavior of the samples have been studied with TEM and EBSD analyses. Further, the evolution of crystallographic texture after creep tests has also been studied. The presence of an intermediate size of martensitic microstructural units (i.e., prior-austenite grain, martensitic packets, etc.) and combination of fine coherent and incoherent Nb(C,N) precipitates has provided superior creep strength for the samples normalized at 1025 °C, when these are subsequently subjected to low-temperature (i.e., 550 °C) and high-temperature (i.e., 650 °C) creep tests, as compared to other conditions of normalizing heat treatment.

36 MATERIALS SCIENCE↗

Graph neural networks for efficient learning of mechanical properties of polycrystals

Herein we present graph neural networks (GNNs) as an efficient and accurate machine learning approach to predict mechanical properties of polycrystalline materials. Here, a GNN was developed based on graph representation of polycrystals incorporating only fundamental features of grains including their crystallographic orientation, size, and grain neighbor connectivity information. We tested our method on modeling stiffness and yield strength of α -Ti microstructures, varying in their crystallographic texture. We find the GNN predicts both properties with high accuracy with mean relative errors of ~1% for unseen microstructures from a given set of textures and < 2% for microstructures of unseen texture, even when presented with limited training data. This accuracy is comparable to methods that require high-resolution three-dimensional (3D) microstructure data, such as 3D convolutional neural networks (3D-CNNs) and models that depend on the computation of spatial statistics. The present results show that graph-based deep learning is a promising framework for property prediction, especially considering the high cost associated with obtaining high-resolution 3D microstructure data and the general scarcity of experimental materials datasets.

36 MATERIALS SCIENCE↗

The onset of alloying in Cu-Ni powders under high-shear consolidation

Friction consolidation (FC) is a solid phase processing methodology that densifies a material through high-shear deformation and pressure at elevated temperature. The method has garnered interest in the scientific community because of its ability to produce extremely refined and homogeneous microstructures, off-axis texture development, and improved material properties. This manuscript presents an investigation of Cu and Ni material mixing via evaluation of morphological evolution, grain boundary characterization, and compositional analysis to provide insights on the operational alloying mechanisms occurring under high shear and elevated temperature. Using correlative microscopy techniques, we show alloying progresses via a combination of grain boundary diffusion and interfacial roughening at heterophane boundaries. Evidence supporting Cu infiltration along Ni-Ni grain boundaries along with asymmetric diffusion of Cu into Ni grains is highlighted. The resultant, consolidated microstructure was produced directly from a powder compact in ~30 s and exhibited a submicron, equiaxed grain size.

36 MATERIALS SCIENCE↗

Ultrasonic additive manufacturing of zirconium: Pilot results

Ultrasonic additive manufacturing (UAM) was successfully applied to the Zirconium material system to create a three-dimensional component prototype. The UAM process resulted in grain size refinement and significant localized deformation. Electron backscatter diffraction analysis revealed activated slip systems only applicable at high deformation temperatures, while texture analysis showed a decrease in measurable texture of the UAM build in comparison to the initial Zr-foil. Average tensile strengths in the X (sonotrode travel), Y (vibration), and Z (build) directions averaged 435 MPa, 458 MPa, and 359 MPa, respectively, demonstrating the viability of UAM for Zr-based materials. Furthermore, the delamination of some Z specimens along foil boundaries during loading suggests an interplay between interfacial Ti impurities introduced during welding and the spatial dependence of weld quality for this material system.

36 MATERIALS SCIENCE↗

Influence of Sn on Martensitic Beta Ti Alloys

The influence of Sn composition in Ti-17 at.% Nb alloys is studied by cyclic tension and in-situ synchrotron X-ray diffraction. It is essentially found that Sn stabilizes β-phase and effectively suppresses the formation of ω-phase. Along with β-phase stability, we detect lowering of the austenite and martensite transformation temperature by ~ 100 K/at.% and 88 K/at.%, respectively. Increasing Sn decreases the martensitic transformation strain in Ti-Nb alloys by ~ 1.4%/at.%, larger than that in Ti-Zr-Nb-Sn systems. The influence of Sn in martensitic Ti is anisotropic: causing larger reduction in lattice parameter b and higher decreases in elastic moduli of grain families that are aligned close to the b -axis. Lastly, a {013} α'' , {031} α'' ,{122} α'' and {211} α'' quadruple texture was observed in martensitic Ti wire. At the early stage of deformation, detwinning quickly rotated {013} α'' and (211} α'' , towards {031} α'' and {122} α'' components. After that, the strength of {031} α'' continued to increase, while the strength of {122} α'' texture was gradually decreased by dislocation slip as deformation continued.

36 MATERIALS SCIENCE↗

Investigation of deformation mechanisms in an advanced FeCrAl alloy using in-situ SEM-EBSD testing

The deformation mechanisms associated with uniaxial tensile testing are observed by conducting tensile experiments of an FeCrAl alloy using scanning electron microscopy (SEM) coupled with electron backscattered diffraction (EBSD). Prior to the deformation, investigated alloy was consisting grain and precipitate size of ~63.0 μm and ~6.7 μm, respectively. The recorded SEM micrographs and EBSD data at increasing levels of strains revealed the complex phenomena of slip bands’ formation in the presence of surface grain morphology evolution and their (001), (110) and (111) crystallographic planes distortions. The grains with orientation (110)||tensile direction (TD) shows higher shape change; however, (001)||TD and (111)||TD oriented grains show higher lattice gradient formation. Extracted information from the EBSD indicates that the crystallographic rotations drive towards specific, fiber-like texture in relation to the loading direction. Postmortem analysis of the recorded microstructure during the tensile deformation explains the phenomena of crack formation in the hard-intermetallic particles before the ultimate tensile strength (UTS). However, after the UTS, pores were identified in the neck that resulted from extensive plastic deformation. In-depth analysis was carried out to identify the cause of cracks and pores formation phenomena during the tensile test.

36 MATERIALS SCIENCE↗

Quasi-static and dynamic response of a Cu/Nb composite following equal channel angular extrusion

The article presents a study of the plastic properties of a Cu–18%Nb composite following equal channel angular extrusion under both low- and high-strain rate loadings. The microstructures are characterized by optical and scanning electron microscopy as well as electron backscatter diffraction. Comparisons are also made with a Cu–50%Nb laminate made by accumulative roll bonding. Textures obtained within the respective phases in the extruded composite closely mimic those previously reported for the pure components alone (Cu, Nb). Grain sizes of the major phase (Cu) exhibit broad distributions, due largely to partial recrystallization during the extrusion process. Further re-crystallization is obtained within localized deformation bands produced at high strain rates (3 × 10 3 s –1 ). While the degree of anisotropy and the strain rate sensitivity of the composite response are similar to those of pure Cu after extrusion, the strength levels of the composite are somewhat greater, falling broadly between those obtained in the pure components after extrusion to comparable plastic strains. Furthermore, the implications for selection of composite composition and processing for achieving higher strengths are briefly discussed.

36 MATERIALS SCIENCE↗

Microstructural Characterization of FeCrAl C26M Tubes

The present report summarizes the initial nanoindentation characterization of a FeCrAl alloy, C26M. Microstructural analysis using electron backscatter diffraction showed a highly textured system with the axial surface favoring orientations near the [110] and the longitudinal surface near the [111]. A large spread of grain sizes was observed from a few μm’s to 100 μm with an average grain size of ~70 μm. Nanoindentation with a Berkovich tip measured a similar hardness and modulus of ~4.4 GPa and ~240 GPa on the two surfaces, respectively. Mounting specimens in epoxy was found to be the cause of a lower stiffness and, consequently, a lower hardness and modulus value. Spherical nanoindentation was measured on the longitudinal surface of the tube to determine the nanoindentation modulus and nanoindentation yield strength. Using a 10 μm tip, the measured modulus was ~220 GPa and the yield strength was ~1.4 GPa. Indentation with a 100 μm tip resulted in a measured modulus value of ~220 GPa and yield strength of ~1.1 GPa. Some early characterization of the differences in spherical nanoindentation response of the axial and longitudinal surfaces showed a small difference between the two, but a more detailed analysis with a stiffer mounting configuration is needed to draw conclusions.

36 MATERIALS SCIENCE↗

Sample size and sampling errors as the source of dispersion in chemical analyses

The paper describes a Monte Carlo model for simulation of two-dimensional representations of thin sections of some of the more common igneous rock textures. These representations are extrapolated to three dimensions to develop a volume of 'rock'. The model (here applied to a medium-grained high-Ti basalt) can be used to determine a statistically significant sample for a lunar rock or to predict the probable errors in the oxide contents that can occur during the analysis of a sample that is not representative of the parent rock.

Clanton, U. S.↗

Lithification of vitric- and clastic-matrix breccias - SEM petrography

A scanning electron microscope was used in a petrographic investigation of the matrix textures of 41 lunar breccias ranging from very friable soil clods through coherent microbreccias and tough vitric breccias to tough, fine-grained crystalline breccias. It was found that as their coherence increases, the matrices display a gradual increase in the content of glass from 1 or 2% as filaments less than 1 micron across through 5-50% as irregularly shaped patches up to 200 microns across to over 50% as continuous networks.

Phinney, W. C.↗

Evaluation of several schemes for classification of remotely sensed data: Their parameters and performance

The author has identified the following significant results. Data sets for corn, soybeans, winter wheat, and spring wheat were used to evaluate the following schemes for crop identification: (1) per point Gaussian maximum classifier; (2) per point sum of normal densities classifiers; (3) per point linear classifier; (4) per point Gaussian maximum likelihood decision tree classifiers; and (5) texture sensitive per field Gaussian maximum likelihood classifier. Test site location and classifier both had significant effects on classification accuracy of small grains; classifiers did not differ significantly in overall accuracy, with the majority of the difference among classifiers being attributed to training method rather than to the classification algorithm applied. The complexity of use and computer costs for the classifiers varied significantly. A linear classification rule which assigns each pixel to the class whose mean is closest in Euclidean distance was the easiest for the analyst and cost the least per classification.

Scholz, D.↗

Relict grains in chondrules

Attention is given to the fact that a significant fraction of the chondrules from ordinary chondrites contain silicate grains that survived the chondrule formation process without melting. Typically, these grains consist of coarse olivine, rarely orthopyroxene, crystals located in the core of chondrules and displaying a zoning that is inconsistent with crystallization from a silicate melt. It is noted that the relict grains still preserve the imprint of processes that occurred in the solar nebula and, in some cases, may include the isotopic record of interstellar grains. Information is presented on the chondrule precursor materials and the process of chondrule formation which was acquired by a compositional and textural study of three of the most unequilibrated type 3 ordinary chondrites.

Rambaldi, E. R.↗

Grain orientation studies in superconductors

Grain oriented fabrication of ceramics utilizes the presence of some form of anisotropy in the particles of the starting material to obtain textured microstructures. The molten salt, or flux method, a popular technique for growing crystals and particles with anisotropic morphology, is utilized in this study. The formation of Ba2YCu3O(7-x) in the presence of molten salts of Na, K, Li belonging to chloride and sulfate systems does not appear feasible in the temperature range up to 900 C. Researchers also present the results of studies in using BaY2CuO5 as seed crystals in the formation of Ba2YCu3O(7-x) wherein BaY2CuO5 has been observed to have better stability in water and against most of the salts as compared to Ba2YCu3O(7-x). Additional results of molten salt processing of bismuth systems are also presented.

Gopalakrishnan, Sudhakar↗

The Black Pearl mine, Arizona - Wolframite veins and stockscheider pegmatite related to an albitic stock

Wolframite-bearing quartz veins flanked by greisen alteration occur at and near the Black Pearl mine, Yavapai County, Arizona. The veins are genetically related to a small albitite stock, and cut a series of Proterozoic metasedimentary and intrusive rocks. The largest vein, the only one mined, is located at the apex of the stock. Field relations imply that this stock is a late-stage differentiate of time 1.4-Ga anorogenic Lawler Peak batholith, which crops out about 3 km to the south. The albitites are of igneous origin and have suffered only minor deuteric alteration. A thin (1 to 2 m) pegmatite unit ('stockscheider') occurs at the contact of the Black Pearl Albitite stock with the country rocks. Directional indicators and other evidence suggest that the pegmatite was formed in the presence of a volatile-rich fluid phase close to the time of magma emplacement. The sudden change from coarse-grained microcline-rich pegmatite to fine-grained, albite-rich albitite suggests pressure quenching, possibly due to escape of fluids up the Black Pearl vein. Stockscheider-like textures typically occur near the apical contacts of productive plutons. The presence or absence of this texture is a useful guide in prospecting for lithophile metal deposits.

Schmitz, Christopher↗

X-ray thermal diffuse scattering as a texture-robust temperature diagnostic for dynamically compressed solids

We present a model of x-ray thermal diffuse scattering (TDS) from a cubic polycrystal with an arbitrary crystallographic texture, based on the classic approach of Warren [B. E. Warren, Acta Crystallogr. 6, 803 (1953)]. We compare the predictions of our model with femtosecond x-ray diffraction patterns gathered from ambient and dynamically compressed rolled copper foils obtained at the High Energy Density instrument of the European X-Ray Free-Electron Laser facility and find that the texture-aware TDS model yields more accurate results than does the conventional powder model owed to Warren. Nevertheless, we further show: with sufficient angular detector coverage, the TDS signal is largely unchanged by sample orientation and in all cases strongly resembles the signal from a perfectly random powder; shot-to-shot fluctuations in the TDS signal resulting from grain-sampling statistics are at the percent level, in stark contrast to the fluctuations in the Bragg-peak intensities (which are over an order of magnitude greater); and TDS is largely unchanged even following texture evolution caused by compression-induced plastic deformation. We conclude that TDS is robust against texture variation, making it a flexible temperature diagnostic applicable just as well to off-the-shelf commercial foils as to ideal powders.

Crystal lattices↗

Deformation processes in forging ceramics

The deformation processes involved in the forging of refractory ceramic oxides were investigated. A combination of mechanical testing and forging was utilized to investigate both the flow and fracture processes involved. Deformation studies of very fine grain Al203 revealed an apparent transition in behavior, characterized by a shift in the strain rate sensitivity from 0.5 at low stresses to near unity at higher stresses. The behavior is indicative of a shift in control between two dependent mechanisms, one of which is indicated to be cation limited diffusional creep with significant boundary enhancement. The possible contributions of slip, indicated by crystallographic texture, interface control of the diffusional creep and inhomogeneous boundary sliding are also discussed. Additional experiments indicated an independence of deformation behavior on MgO doping and retained hot pressing impurities, at least for ultrafine grained material, and also an independence of test atmosphere.

Cannon, R. M.↗