SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Explore the source record for details and available documents.
The objective of this paper is to compare the results of several simulations performed to determine the worst-case location for a foam impact on the Space Shuttle wing leading edge. The simulations were performed using the commercial non-linear transient dynamic finite element code, LS-DYNA. These simulations represent the first in a series of parametric studies performed to support the selection of the worst-case impact scenario. Panel 9 was selected for this study to enable comparisons with previous simulations performed during the Columbia Accident Investigation. The projectile for this study is a 5.5-in cube of typical external tank foam weighing 0.23 lb. Seven locations spanning the panel surface were impacted with the foam cube. For each of these cases, the foam was traveling at 1000 ft/s directly aft, along the orbiter X-axis. Results compared from the parametric studies included strains, contact forces, and material energies for various simulations. The results show that the worst case impact location was on the top surface, near the apex.
Segregation of alloying elements to a prismatic dislocation loop under irradiation is an important phenomenon in understanding the role of loops in radiation effects in alloys. In this work, various segregation sequences of Cr and Al atoms to a $\langle$100$\rangle$ and a 1/2 $\langle$111$\rangle$ prismatic dislocation loop in a Fe-Cr-Al alloy are explored using molecular dynamics method and ab initio energy calculation. Here, the results reveal that Cr can readily segregate to the loops while Al atoms cannot by themselves, but the segregated Cr atoms are able to promote Al segregation at the loops, defined as a coupled segregation of Cr and Al. After interacting with Cr and Al, a previously mobile 1/2 $\langle$111$\rangle$ loop becomes sessile. Al segregation through the coupled segregation process can further affect the pinning behavior of a dislocation loop to an edge dislocation motion. By varying the Al fraction in the segregated solutes, a nonlinear dependence of the pinning effect on dislocation motion is determined. At lower fractions, the pinning strength increases with the increasing Al fraction until Al fraction reaches a critical value of about 19%, above which the pinning strength decreases with further increase of Al fraction. All these results suggest that, in addition to the effect of Al on the surface resistance to oxidation, Al effect on the dislocation loop behavior is important to optimize the composition of Fe-Cr-Al alloys for their applications in accident tolerant fuel concepts.
Six wing models were tested in the Langley Unitary Plan Wind Tunnel to identify and study leading-edge thrust at supersonic speeds. The tests were conducted at Mach numbers of 1.6, 1.8, 2.0, and 2.16, at a stagnation temperature of 125.0 F, and at Reynolds numbers per foot of 2.0 x 10 to the 6th power and 5.0 x 10 the 6th power. Test results showed that significant benefits from leading-edge thrust and nonlinear thickness effects can be obtained with very little airfoil bluntness, that these benefits were lost when the airfoil was severely blunted, and that such benefits seem to be found on wings with supersonic as well as subsonic leading edges.
A wind-tunnel investigation was made to determine the effects of ejecting high-velocity air near the leading edge of plain trailing-edge flaps on a 35 degree sweptback wing. The tests were made with flap deflections from 45 degrees to 85 degrees and with pressure ratios across the flap nozzles from sub-critical up to 2.9. A limited study of the effects of nozzle location and configuration on the efficiency of the flap was made. Measurements of the lift, drag, and pitching moment were made for Reynolds numbers from 5.8 to 10.1x10(6). Measurements were also made of the weight rate of flow, pressure, and temperature of the air supplied to the flap nozzles.The results show that blowing on the deflected flap produced large flap lift increments. The amount of air required to prevent flow separation on the flap was significantly less than that estimated from published two-dimensional data. When the amount of air ejected over the flap was just sufficient to prevent flow separation, the lift increment obtained agreed well with linear inviscid fluid theory up to flap deflections of 60 degrees. The flap lift increment at 85 degrees flap deflection was about 80 percent of that predicted theoretically.With larger amounts of air blown over the flap, these lift increments could be significantly increased. It was found that the performance of the flap was relatively insensitive to the location of the flap nozzle, to spacers in the nozzle, and to flow disturbances such as those caused by leading-edge slats or discontinuities on the wing or flap surfaces. Analysis of the results indicated that installation of this system on an F-86 airplane is feasible.
The goal set forth here is to continue the work started by Braun et al. (1984-1985) and present an integrated analysis of the behavior of the two row, 20 staggered pockets, hydrostatic cryogenic bearing used by the turbopumps of the Space Shuttle main engine. The variable properties Reynolds equation is fully coupled with the two-dimensional fluid film energy equation. The three-dimensional equations of the shaft and bushing model the boundary conditions of the fluid film energy equation. The effects of shaft eccentricity, angular velocity, and inertia pressure drops at pocket edge are incorporated in the model. Their effects on the bearing fluid properties, load carrying capacity, mass flow, pressure, velocity, and temperature form the ultimate object of this paper.
The valence of Cu and Au in YBa2Au0.3Cu2.7O7-delta was investigated using x-ray absorption near edge structure (XANES). X-ray and neutron diffraction studies indicate that Au goes on the Cu(1) site and Cu K-edge XANES shows that this has little effect on the oxidation state of the remaining copper. The Au L3 edge develops a white line feature whose position lies between that of trivalent gold oxide and monovalent potassium gold cyanide, and whose height relative to the edge step is smaller than in the two reference compounds. The appearance of the Au L3 edge suggests that fewer Au 3d states are involved in forming the Au-O bond in YBa2Au0.3Cu2.7O7-delta than in trivalent gold oxide.
The valence of Cu and Au in YBa2Au0.3Cu2.7O7-delta was investigated using X-ray absorption near edge structure (XANES). X-ray and neutron diffraction studies indicate that Au goes on the Cu(1) site and Cu K-edge XANES shows that this has little effect on the oxidation state of the remaining copper. The Au L3 edge develops a white line feature whose position lies between that of trivalent gold oxide and monovalent potassium gold cyanide, and whose height relative to the edge step is smaller than in the two reference compounds. The appearance of the Au L3 edge suggests that fewer Au 3d states are involved in forming the Au-O bond in YBa2Au0.3Cu2.7O7-delta than in trivalent gold oxide.
The observed discrepancy at supersonic speeds between theoretical and apparent experimental average flat plate friction-drag coefficients calculated from boundary layer total-pressure surveys was investigated. Effects of the total-pressure probe, heat transfer through the leading edge region, change in leading-edge radius and strength of the leading-edge wave, possible early transition to turbulent flow or “bursts of turbulence,” and the slight stream-wise pressure gradient inherent in flat plate flow were investigated for plates with very sharp leading edges. Only one of these factors, the effect of the total-pressure probe, was found to be significant. Total-pressure probes of different tip heights, when placed in laminar boundary layers developing under identical conditions, were found to yield different values of friction drag coefficient. Extrapolation of these measurements indicates that a probe of vanishing size would yield the theoretical predicted values of average flat plate friction-drag coefficients. A correlation describing the relation between the friction-drag discrepancy and the probe tip height is presented.
A wind-tunnel investigation of horn balances on a 45 degree sweptback, semispan, horizontal tail surface was made to determine the effects of horn size and inboard-edge fairing at a Mach number of 0.30 and to determine the effects of compressibility up to a Mach number of 0.89. Presented are lift, drag, pitching-moment, and hinge-moment data and lift and hinge-moment parameters.
Freely suspended smectic films of sub-micrometer thickness and lateral extensions of several millimeters are used to study thermally driven convection and diffusion in the film plane. The experiments were performed during a six minute microgravity phase of a TEXUS suborbital rocket flight (Texus 52, launched April 27, 2015). The project served as a preliminary test for a planned ISS Experiment with liquid crystal films (OASIS), and in addition it provided new experimental data on smectic films exposed to in-plane thermal gradients.We find an attraction of the smectic material towards the cold edge of the film in a temperature gradient, similar to a Soret effect. This process is reversed when this edge is heated up again. Thermal convection driven by two thermocontacts in the film is practically absent, even at temperature gradients up to 10 Kmm, thermally driven convection sets in when the hot post reaches the transition temperature to the nematic phase.An additional experiment was performed under microgravity conditions to test the stability of liquid crystal bridges in different smectic phases.
Abstract It is determined that while heat flux differences between hydrogen and deuterium isotope experiments result from natural differences in carbon impurity content at DIII-D, it is not the origin of the low to high confinement mode (L-H) transition isotope effect. More specifically, a two times larger edge radial electric field in hydrogen compared to deuterium is uncovered and believed to play an important role. The origin of this radial electric field difference is determined to have two possible origins: differences in poloidal rotation and turbulent Reynolds stress in the closed field line region, and increased outer strike point temperatures and space potentials on open field lines. Experimental observations from both profile and turbulence diagnostics are supported by nonlinear gyrokinetic simulations using the code CGYRO. Simulations illustrated heat transport isotope effects in the plasma edge and shear layer resulting from differences in impurity content, electron non-adiabaticity, and main ion mass dependent E × B shear stabilization. Turbulence prediction comparisons from flux-matched CGYRO simulations to experimental measurements including electron temperature, density and velocity fluctuations are found to be in good agreement with available data. A dedicated DIII-D experiment in hydrogen was performed to seed more carbon than naturally occurring, to match deuterium experiments, and possibly reduce the L-H power threshold based on gyro-kinetic predictions. To our surprise, while ion temperature gradient (ITG) turbulence was stabilized, nodiscernible change in L-H power threshold were observed in these special hydrogen experiments. In particular, it is noticed that the edge radial electric field and Reynolds stress were observed as nearly unchanging in the presence of ITG stabilization. These experimental data have enabled a more comprehensive picture of the multitude of isotope effects at play in fusion experiments, and the important potential connection between the confined and unconfined plasma regions in regulating L-H transition dynamics.
Gapless helical edge modes are a hallmark of the quantum spin Hall effect. Protected by time-reversal symmetry, each edge contributes a quantized zero-temperature conductance quantum G 0 ≡ e 2 /h. However, the experimentally observed conductance in WT e2 decreases below G 0 per edge already at edge lengths around 100 nm, even in the absence of explicit time-reversal breaking due to an external field or magnetic impurities. Here we show how a time-reversal breaking excitonic condensate with a spin-spiral order that can form in WT e2 leads to the breakdown of conductance quantization. We perform Hartree-Fock calculations to compare time-reversal breaking and preserving excitonic insulators. Using these mean-field models we demonstrate via quantum transport simulations that weak nonmagnetic disorder reproduces the edge length scaling of resistance observed in the experiments. We complement this by analysis in the Luttinger liquid picture, shedding additional light on the mechanism behind the quantization breakdown.
It is shown that the shock wave intensity can be decreased by using modified trailing edge configurations to reduce or even completely compensate for the effect of the finite thickness of the trailing edge. A theoretical analysis is presented together with numerical results for two supersonic streams flowing off the trailing edge at different velocities. The analysis is based on an ideal gas model.
The characteristics of a parasitic microstrip antenna array with a center-fed patch are experimentally investigated. The parasitic array is composed of identical parasitic patches which are symmetrically arranged and electromagnetically coupled to a center-fed patch. The shape and dimensions of the parasitic patches and their positions relative to the center-fed patch are parameters in the study. To show mutual coupling effects between radiating and nonradiating edges of adjacent patches, the impedance and radiation characteristics of a three-element parasitic array excited with (0.1) mode are examined, and compared to that of a single patch. Experimental data indicate that the presence of parasitic patches has significant effects upon the gain, resonant frequency, and impedance bandwidth of the array.
Tests have been conducted in the Langley 8-foot transonic tunnel on a 0.04956-scale model of the Convair F-102A airplane which employed an indented and extended fuselage, cambered wing leading edges, and deflected wing tips. Force and moment characteristics were obtained for Mach numbers from 0.60 to 1.135 at angles of attack up to 20 . In addition, tests were made over a limited angle-of-attack range to determine the effects of the cambered leading edges, deflected tips, and a nose section with a smooth area distribution. Fuselage modifications employed on the F-102A were responsible for a 25.percent reduction in the minimum drag-coefficient rise between the Mach numbers of 0.85 and 1.075 when compared with that for the earlier versions of the F-102. Although the wing modifications increased the F-102A subsonic minimum drag-coefficient level approximately 0.0020, they produced large decreases in drag at lifting conditions over that for the original (plane-wing) F-102. The F-102A had 15 to 25 percent higher maximum lift-drag ratios than did the original F-102. The F-102A had about 15 percent lower maximum lift-drag ratios at Mach numbers below 0.95 and slightly higher maximum lift-drag ratios at supersonic speeds when compared with those ratios for sn earlier modified-wing version of the F-102. Chordwise wing fences which provided suitable longitudinal stability for the original F-102 were not adequate for the cambered-wing F-102A The pitching-moment curves indicated a region of near neutral stability with possible pitch-up tendencies for the F-102A at high subsonic Mach numbers for lift coefficients between about 0.4 and 0.5.
Hybrid wing planforms are studied for adoption on supersonic transport and fighter aircraft. The free vortex sheet method is used to determine effects of the leading-edge sweep angles on the aerodynamic performance of a double arrow wing with a strake. Results show lift and drag increase with the increase of the inboard and outboard leading-edge sweep angles. However, the lift-to-drag ratio is little influenced by the changes in these sweep angles. Spanwise surface pressure distributions on the aft region are influenced by the inboard sweep angle while the outboard sweep angle has no effect on these pressures. Finally, the experimental data and predicted results are compared to show good agreement.
An investigation has been conducted in the Langley full-scale tunnel to determine the effects of a blowing boundary-layer-control lift-augmentation system on the aerodynamic characteristics of a large-scale model of a fighter-type airplane. The wing was unswept at the 70-percent- chord station, had an aspect ratio of 2.86, a taper ratio of 0.40, and 4-percent-thick biconvex airfoil sections parallel to the plane of symmetry. The tests were conducted over a range of angles of attack from approximately -4 deg to 23 deg for a Reynolds number of approximately 5.2 x 10(exp 6) which corresponds to a Mach number of 0.08. Blowing rates were normally restricted to values just sufficient to control air-flow separation. The results of this investigation showed that wing leading-edge blowing in combination with large values of wing leading-edge-flap deflection was a very effective leading-edge flow-control device for wings having highly loaded trailing-edge flaps. With leading-edge blowing there was no hysteresis of the lift, drag, and pitching-moment characteristics upon recovery from stall. End plates were found to improve the lift and drag characteristics of the test configuration in the moderate angle-of-attack range, and blockage to one-quarter of the blowing-slot area was not detrimental to the aerodynamic characteristics. Blowing boundary-layer control resulted in a considerably reduced landing speed and reduced landing and take-off distances. The ailerons were very effective lateral-control devices when used with blowing flaps.