Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “data transport”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 991 records · Page 55
All sourcesNASA NTRSDOE OSTI
NASA NTRS1994

Transportable Payload Operations Control Center reusable software: Building blocks for quality ground data systems

The Mission Operations Division (MOD) at Goddard Space Flight Center builds Mission Operations Centers which are used by Flight Operations Teams to monitor and control satellites. Reducing system life cycle costs through software reuse has always been a priority of the MOD. The MOD's Transportable Payload Operations Control Center development team established an extensive library of 14 subsystems with over 100,000 delivered source instructions of reusable, generic software components. Nine TPOCC-based control centers to date support 11 satellites and achieved an average software reuse level of more than 75 percent. This paper shares experiences of how the TPOCC building blocks were developed and how building block developer's, mission development teams, and users are all part of the process.

Mahmot, Ron↗
NASA NTRS1977

Joint DOD/NASA study: Consolidation of expendable launch vehicles during transition to the space transportation system

A considerable amount of data is presented which was needed to compare consolidation options. The study shows that there is no clean-cut DOD/NASA advantage for consolidation. However, for DOD uses, the technical advantage of using the Titan III/IUS for the Titan IIIC in the transition era, coupled with a possible cost-push in converting to the Titan III/IUS, warrants serious DOD consideration.

Source record↗
NASA NTRS1979

Lateral noise-attenuation results from flyovers of three transport aircraft

Lateral noise-attenuation data have been compiled in a one-third-octave-band analysis from an available set of flyover tests using DC-8, DC-9, and DC-10 aircraft. For an intermediate frequency range of 400 through 2000 Hertz the lateral noise has been approximately separated into its two components - the excess ground attenuation and the aircraft shielding attenuation. Both attenuation factors varied from a maximum at small elevation angles to zero at an elevation angle of approximately 40 degrees. The lateral attenuation in this range generally did not vary with frequency. For frequencies of 80 Hertz and lower, negative lateral attenuation values were obtained. For high frequencies, the data were not complete enough to generate definitive lateral attenuation curves.

Mashita, E. M.↗
NASA NTRS2001

Planning of reach-and-grasp movements: effects of validity and type of object information

Individuals are assumed to plan reach-and-grasp movements by using two separate processes. In 1 of the processes, extrinsic (direction, distance) object information is used in planning the movement of the arm that transports the hand to the target location (transport planning); whereas in the other, intrinsic (shape) object information is used in planning the preshaping of the hand and the grasping of the target object (manipulation planning). In 2 experiments, the authors used primes to provide information to participants (N = 5, Experiment 1; N = 6, Experiment 2) about extrinsic and intrinsic object properties. The validity of the prime information was systematically varied. The primes were succeeded by a cue, which always correctly identified the location and shape of the target object. Reaction times were recorded. Four models of transport and manipulation planning were tested. The only model that was consistent with the data was 1 in which arm transport and object manipulation planning were postulated to be independent processes that operate partially in parallel. The authors suggest that the processes involved in motor planning before execution are primarily concerned with the geometric aspects of the upcoming movement but not with the temporal details of its execution.

Cues↗
NASA NTRS1998

The Aviation Performance Measuring System (APMS): An Integrated Suite of Tools for Measuring Performance and Safety

This is a report of work in progress. In it, I summarize the status of the research and development of the Aviation Performance Measuring System (APMS) for managing, processing, and analyzing digital flight-recorded data, The objectives of the NASA-FAA APMS research project are to establish a sound scientific and technological basis for flight-data analysis, to define an open and flexible architecture for flight-data analysis systems, and to articulate guidelines for a standardized database structure on which to continue to build future flight-data-analysis extensions. APMS offers to the air transport community an open, voluntary standard for flight-data-analysis software; a standard that will help to ensure suitable functionality and data interchangeability among competing software programs. APMS will develop and document the methodologies, algorithms, and procedures for data management and analyses to enable users to easily interpret the implications regarding safety and efficiency of operations. APMS does not entail the implementation of a nationwide flight-data-collection system. It is intended to provide technical tools to ease the large-scale implementation of flight-data analyses at both the air-carrier and the national-airspace levels in support of their Flight Operations and Quality Assurance (FOQA) Programs and Advanced Qualifications Programs (AQP). APMS cannot meet its objectives unless it develops tools that go substantially beyond the capabilities of the current commercially available software and supporting analytic methods that are mainly designed to count special events. These existing capabilities, while of proven value, were created primarily with the needs-of aircrews in mind. APMS tools must serve the needs of the government and air carriers, as well as aircrews, to fully support the FOQA and AQP programs. They must be able to derive knowledge not only through the analysis of single flights (special-event detection), but also through statistical evaluation of the performance of large groups of flights. This paper describes the integrated suite of tools that will assist analysts in evaluating the operational performance and safety of the national air transport system, the air carrier, and the aircrew.

Statler, Irving C.↗
NASA NTRS2017

A Dose of Reality: Radiation Analysis for Realistic Human Spacecraft

INTRODUCTION As with most computational analyses, a tradeoff exists between problem complexity, resource availability and response accuracy when modeling radiation transport from the source to a detector. The largest amount of analyst time for setting up an analysis is often spent ensuring that any simplifications made have minimal impact on the results. The vehicle shield geometry of interest is typically simplified from the original CAD design in order to reduce computation time, but this simplification requires the analyst to "re-draw" the geometry with a limited set of volumes in order to accommodate a specific radiation transport software package. The resulting low-fidelity geometry model cannot be shared with or compared to other radiation transport software packages, and the process can be error prone with increased model complexity. The work presented here demonstrates the use of the DAGMC (Direct Accelerated Geometry for Monte Carlo) Toolkit from the University of Wisconsin, to model the impacts of several space radiation sources on a CAD drawing of the US Lab module. METHODS The DAGMC toolkit workflow begins with the export of an existing CAD geometry from the native CAD to the ACIS format. The ACIS format file is then cleaned using SpaceClaim to remove small holes and component overlaps. Metadata is then assigned to the cleaned geometry file using CUBIT/Trelis from csimsoft (Registered Trademark). The DAGMC plugin script removes duplicate shared surfaces, facets the geometry to a specified tolerance, and ensures that the faceted geometry is water tight. This step also writes the material and scoring information to a standard input file format that the analyst can alter as desired prior to running the radiation transport program. The scoring results can be transformed, via python script, into a 3D format that is viewable in a standard graphics program. RESULTS The CAD model of the US Lab module of the International Space Station, inclusive of all the racks and components, was simplified to remove holes and volume overlaps. Problematic features within the drawing were also removed or repaired to prevent runtime issues. The cleaned drawing was then run through the DAGMC workflow to prepare for analysis. Pilot tests modeling transport of 1GeV proton and 800MeV/A oxygen sources show that reasonable results are converged upon in an acceptable amount of overall computation time from drawing preparation to data analysis. The FLUKA radiation transport code will next be used to model both a GCR and a trapped radiation source. These results will then be compared with measurements that have been made by the radiation instrumentation deployed inside the US Lab module. DISCUSSION Early analyses have indicated that the DAGMC workflow is a promising toolkit for running vehicle geometries of interest to NASA through multiple radiation transport codes. In addition, recent work has shown that a realistic human phantom, provided via a subcontract with the University of Florida, can be placed inside any vehicle geometry for a combinatorial analysis. This added functionality gives the user the ability to score various parameters at the organ level, and the results can then be used as input for cancer risk models.

Barzilla, J. E.↗
NASA NTRS1973

Distribution of surface extremes in the United States

Extreme design environment data are presented for consideration in aerospace vehicle transportation, fabrication, or testing. Values were obtained by using data from weather stations and published meteorological articles. Maps depict snow fall, hail distribution, atmospheric pressure, atmospheric temperature, and surface elevations.

Daniels, G. E.↗
NASA NTRS2012

CO2 Flux Estimation Errors Associated with Moist Atmospheric Processes

Vertical transport by moist sub-grid scale processes such as deep convection is a well-known source of uncertainty in CO2 source/sink inversion. However, a dynamical link between vertical transport, satellite based retrievals of column mole fractions of CO2, and source/sink inversion has not yet been established. By using the same offline transport model with meteorological fields from slightly different data assimilation systems, we examine sensitivity of frontal CO2 transport and retrieved fluxes to different parameterizations of sub-grid vertical transport. We find that frontal transport feeds off background vertical CO2 gradients, which are modulated by sub-grid vertical transport. The implication for source/sink estimation is two-fold. First, CO2 variations contained in moist poleward moving air masses are systematically different from variations in dry equatorward moving air. Moist poleward transport is hidden from orbital sensors on satellites, causing a sampling bias, which leads directly to small but systematic flux retrieval errors in northern mid-latitudes. Second, differences in the representation of moist sub-grid vertical transport in GEOS-4 and GEOS-5 meteorological fields cause differences in vertical gradients of CO2, which leads to systematic differences in moist poleward and dry equatorward CO2 transport and therefore the fraction of CO2 variations hidden in moist air from satellites. As a result, sampling biases are amplified and regional scale flux errors enhanced, most notably in Europe (0.43+/-0.35 PgC /yr). These results, cast from the perspective of moist frontal transport processes, support previous arguments that the vertical gradient of CO2 is a major source of uncertainty in source/sink inversion.

moist atmospheric processes↗
DOE OSTI2025

Intrachain Electron Transport in a Naphthalene Diimide–Bithiophene Copolymer: A Mixed-Valence Approach

The mechanism of electron transport in the polymer P(NDI2OD-T2) (poly(N,N'-bis-2-octyldodecylnaphthalene-1,4,5,8-bis-dicarboximide-2,6-diyl-alt-2,2'-bithiophene-5,5'-diyl), N2200) is investigated. Here, we use spectroelectrochemical measurements on P(NDI2OD-T2), spectroscopic studies of a chemically reduced model compound, 2,2'-(2,2'-bithiophene-5,5'-diyl)-bis(N,N'-di-n-hexylnaphthalene-1,8:4,5-bis(dicarboximide)) (NDI-T2-NDI), and electronic structure calculations to evaluate the microscopic charge-transport parameters. Experimental and computational data suggest that NDI-T2-NDI•– is a class-II mixed-valence compound, strongly supporting the small-polaron hopping model as a charge-transport mechanism for electrons along polymer chains in P(NDI2OD-T2). The electronic coupling between the NDI redox units is at least 21 meV, while the reorganization energy is between 0.45 and 0.56 eV. Using a hopping model, we estimated the mobility and activation energy for electron transport along P(NDI2OD-T2) polymer chains to be 0.15 cm 2 V –1 s –1 and 60 meV, respectively. Our study elucidates a long-standing issue of explaining the coexistence in P(NDI2OD-T2) of localized redox sites with relatively large electron mobilities more usually achieved only in highly conjugated polymers.

36 MATERIALS SCIENCE↗
DOE OSTI2023

How Time Inefficient and Uncertain are Paratransit Trips Compared to Car Trips

The Americans with Disabilities Act (ADA) stipulates that paratransit mobility be comparable to public transit. However, with just under 5% of the population relying on public transportation, transit is not a representative benchmark. To highlight this inequality, we compare trip times by paratransit to counterfactual car-based travel. Using 2.5 years of demand data from the Denver Regional Transportation District's Access-a-Ride service, we compare paratransit trip times to counterfactual car-based trips for the same origin-destination pairs, controlling for various trip characteristics. Compared to car travel, the findings indicate high variability and uncertainty associated with paratransit trip times. For the same origin-destination pairs, the mean paratransit trip time is almost twice that of the mean car travel time, with a standard deviation for paratransit trip time fourfold that of the standard deviation for car trip time. For perspective, traveling an average of 10 mi during the 7-8 a.m. morning peak can take about 16 min by car with almost no variability, while that same trip can take an average of 25 min by paratransit, with 5% of trips being outside the 95% confidence interval and thus unpredictable. Paratransit trip time inefficiency tends to be particularly worse for females; older adults; those making trips between 9 and 11 a.m.; cash-paying customers; those making shorter trips; and those traveling during inclement weather, including cold temperatures. These findings suggest a need to re-assess using public transit as a benchmark for paratransit supply as regulated by the ADA.

accessible transportation and mobility↗
NASA NTRS1977

Variability and transport of ozone at the tropopause from the first year of GASP data

The relationships of ozone near the tropopause with potential vorticity temperature, and distance from the tropopause are examined. Data are also used to estimate the vertical and horizontal fluxes of ozone near the tropopause. The present estimates of the total flux of ozone into the troposphere verify the model results. Although the distribution of flux between mean motions and diffusion is different and thus suggests that models with coarse horizontal resolution must continue to parameterize much vertical transport by diffusion coefficients. Monthly estimates of the horizontal transient eddy flux of ozone are generally smaller than seasonal or yearly results based on ozonesonde data. This is perhaps because the present estimates are made over monthly periods to reduce the influence of correlation between the annual variations in ozone and meridional wind. The available data support the hypothesis that transient eddy fluxes of ozone have large longitudinal variations.

Nastrom, G. D.↗
NASA NTRSDate not supplied

Sherlock Data Warehouse

Technical Interchange Meeting 2 of 2, with two linked events. Overall Purpose of the Technical Interchange Meeting was to facilitate collaboration on NAS data analytics between FAA and NASA teams, leveraging the great tool developed by NASA, Sherlock Data Warehouse. Conducted the two TIM events, next step is for the leadership to meet and discuss potential future collaborations. Purpose for Technical Interchange Meeting #2 (TIM 2o2); NASA presented data science related use-cases and applications where they have leveraged the NASA Sherlock Data Warehouse to address aviation transportation problems, with priority on aviation safety.

Two TIMs↗
DOE OSTI2023

UNF-ST&DARDS Enhancements for RCCA Data in As-loaded Dual Purpose Cask Models

This report summarizes the work performed to enable detailed modeling of rod cluster control assembly (RCCAs) in dual purpose canisters (DPCs) in as-loaded configurations using the Used Nuclear Fuel – Storage, Transportation & Disposal Analysis Resource and Data System (UNF-ST&DARDS). The goal of this project was to evaluate the reactivity impact that RCCAs have on k eff of DPCs with pressurized water reactor (PWR) fuel to potentially use the additional margin in future post-closure criticality safety analysis. This preliminary evaluation determined the number of DPCs that currently require compensatory actions prior to emplacement in a repository because of their high reactivity under post-closure criticality scenarios, which could be made acceptable by including the as-loaded RCCAs as specified in the Unified Database (UDB). This report briefly describes the modeling methods currently used within UNF-ST&DARDS and the modifications made to automate inclusion of the as-loaded RCCAs in the DPCs for post-closure criticality calculations for the loss of neutron absorber (NA) scenarios, or NA models. For the Zion site, the loss of basket scenarios, or degraded basket (DB) models, are also included. Discussion is also provided regarding the UDB data compared to available site-specific loading map data for the sites, which are specifically evaluated herein. This report compares the modifications to a similar evaluation for the Zion by site conducted by Walker as an initial validation. After the partial validation, all existing PWR sites with applicable NA models within the UDB were evaluated.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1973

Thermodynamic and transport properties of cryogenic propellants and related fluids

Significant advances have been made in recent years in the quality and range of thermophysical data for the cryogenic propellants, pressurants, and inertants. A review of recently completed and current data compilation projects for helium, hydrogen, argon, nitrogen, oxygen, fluorine, and methane is given together with recommended references for thermodynamic and transport property data tables for these fluids. Modern techniques in the plotting of thermodynamic charts from tabular data (or from functions such as the equation of state) have greatly improved their precision and value. A list of such charts is included.

Johnson, V. J.↗
DOE OSTI2023

MPACT 4.4 Theory Manual

MPACT is a three-dimensional (3D) full-core neutron transport code capable of calculating subpin power distributions. Calculations are based on the Boltzmann transport equation for neutron fluxes for problems in which the detailed geometrical configuration of fuel components such as the pellet and cladding are explicitly retained. The cross-section data needed for the neutron transport calculation are obtained directly from a multigroup cross section library, which has traditionally been used by lattice physics codes to generate few-group homogenized cross sections for nodal core simulators. Hence, MPACT assumes neither a priori homogenization nor group condensation for the full core spatial solution. The 3D MPACT transport solution can be obtained using the method of characteristics (MOC), which employs discrete ray tracing within each fuel pin. However, for practical reactor applications, the direct application of MOC to 3D core configurations requires an excessive amount of memory and computing time due to the very large number of rays. For practical 3D full-core calculations, MPACT commonly uses an approximate “2D/1D” method that treats the radial (x and y) variables differently from the axial (z) variable. In particular, the radial dependence of the solution is calculated using transport theory, and the axial dependence is calculated using diffusion or P 3 theory. The 2D/1D method requires the core to be divided into a vertical stack of axial slices with a thickness of Δ z ≈ 5–10 cm. Each axial slice is divided radially into coarse spatial cells with boundaries that usually constitute the pin cell boundaries, for which Δ x = Δ y ≈ 1.5 cm. Then, each coarse radial cell (pin cell) is divided into 50–100 fine radial cells, which resolve the angular flux in the fuel, cladding, and moderator regions.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
NASA NTRS1981

Advanced oxygen-hydrocarbon rocket engine study

This study identifies and evaluates promising LO2/HC rocket engine cycles, produces a consistent and reliable data base for vehicle optimization and design studies, demonstrates the significance of propulsion system improvements, and selects the critical technology areas necessary to realize an improved surface to orbit transportation system. Parametric LO2/HC engine data were generated over a range of thrust levels from 890 to 6672 kN (200K to 1.5M 1bF) and chamber pressures from 6890 to 34500 kN (1000 to 5000 psia). Engine coolants included RP-1, refined RP-1, LCH4, LC3H8, LO2, and LH2. LO2/RP-1 G.G. cycles were found to be not acceptable for advanced engines. The highest performing LO2/RP-1 staged combustion engine cycle utilizes LO2 as the coolant and incorporates an oxidizer rich preburner. The highest performing cycle for LO2/LCH4 and LO2/LC3H8 utilizes fuel cooling and incorporates both fuel and oxidizer rich preburners. LO2/HC engine cycles permitting the use of a third fluid LH2 coolant and an LH2 rich gas generator provide higher performance at significantly lower pump discharge pressures. The LO2/HC dual throat engine, because of its high altitude performance, delivers the highest payload for the vehicle configuration that was investigated.

Obrien, C. J.↗
NASA NTRS2002

An Analysis of U.S. Civil Rotorcraft Accidents by Cost and Injury (1990-1996)

A study of rotorcraft accidents was conducted to identify safety issues and research areas that might lead to a reduction in rotorcraft accidents and fatalities. The primary source of data was summaries of National Transportation Safety Board (NTSB) accident reports. From 1990 to 1996, the NTSB documented 1396 civil rotorcraft accidents in the United States in which 491 people were killed. The rotorcraft data were compared to airline and general aviation data to determine the relative safety of rotorcraft compared to other segments of the aviation industry. In depth analysis of the rotorcraft data addressed demographics, mission, and operational factors. Rotorcraft were found to have an accident rate about ten times that of commercial airliners and about the same as that of general aviation. The likelihood that an accident would be fatal was about equal for all three classes of operation. The most dramatic division in rotorcraft accidents is between flights flown by private pilots versus professional pilots. Private pilots, flying low cost aircraft in benign environments, have accidents that are due, in large part, to their own errors. Professional pilots, in contrast, are more likely to have accidents that are a result of exacting missions or use of specialized equipment. For both groups judgement error is more likely to lead to a fatal accident than are other types of causes. Several approaches to improving the rotorcraft accident rate are recommended. These mostly address improvement in the training of new pilots and improving the safety awareness of private pilots.

Iseler, Laura↗
NASA NTRS1980

Normal mode analysis of the IUS/TDRS payload in a payload canister/transporter environment

Special modeling techniques were developed to simulate an accurate mathematical model of the transporter/canister/payload system during ground transport of the Inertial Upper Stage/Tracking and Data Relay Satellite (IUS/TDRS) payload. The three finite element models - the transporter, the canister, and the IUS/TDRS payload - were merged into one model and used along with the NASTRAN normal mode analysis. Deficiencies were found in the NASTRAN program that make a total analysis using modal transient response impractical. It was also discovered that inaccuracies may exist for NASTRAN rigid body modes on large models when Given's method for eigenvalue extraction is employed. The deficiencies as well as recommendations for improving the NASTRAN program are discussed.

Meyer, K. A.↗