Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “boundary layer”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 991 records · Page 55
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

Diffusion processes in the magnetopause boundary layer

A quantitative estimate is calculated for the effect of wave-particle scattering on the structure of the magnetopause boundary layer. It is assumed that large cross-B electric fields are absent in the observed penetration of magnetosheath plasma into the magnetopause boundary layer, thus allowing for cross-field transport comparable to 10% of the Bohm diffusion. It is shown that magnetosheath ions, resonant with low frequency electrostatic waves, can account for the typical boundary layer thickness when transported at 10% of the diffusion rate 1000 sq km/sec. The conditions are required to occur at all local times and under all interplanetary conditions. Significant mass and momentum transfer are then possible across the magnetopause when field merging is not occurring.

Tsurutani, B. T.↗
NASA NTRS1986

Wall layer models for the calculation of velocity and heat transfer in turbulent boundary layers

In the computation of turbulent boundary-layer flows and internal flows, a substantial amount of mesh points and computational effort is required to adequately resolve the intense temperature and velocity profile variations in the near wall region. In this study, analytical profile approximations are obtained for the mean velocity and temperature distribution in the wall layer; these profiles are based upon consideration of the observed coherent structure of the time-dependent wall-layer flow. The profile approximations are relatively simple analytical formulae which satisfy all the required compatibility conditions at the wall and the logarithmic behavior at the edge of the wall layer. The Reynolds analogy for heat transfer is not used in the present theory. A general method for utilizing the present wall-layer profile models in a prediction method is indicated.

Walker, J. D. A.↗
NASA NTRS1974

An eddy-viscosity treatment of the unsteady turbulent boundary layer on a flat plate in an expansion tube

An analysis is presented for the relaxation of a turbulent boundary layer on a semiinfinite flat plate after passage of a shock wave and a trailing driver gas-driven gas interface. The problem has special application to expansion tube flows. The flow-governing equations have been transformed into the Lamcrocco variables. The numerical results indicate that a fully turbulent boundary layer relaxes faster to the final steady-state values of heat transfer and skin-friction than a fully laminar boundary layer.

Gupta, R. N.↗
NASA NTRS1983

A study of non-unique solutions of the two-dimensional boundary layer equations at laminar separation and reattachment points

Nonunique laminar boundary layer equation solutions in direct problem calculations are identified for the case of accelerating flow. As a separation or reattachment point is approached, the multiple solutions approach each other and become identical. The computer code used to generate these results was developed for the solution of compressible, laminar or turbulent boundary layer, and free wake problems, in either direct or inverse mode. Similarity solutions in either a primitive variable or a stream function form are possible, and the resulting equations are solved by means of a modified Keller's Box scheme in which the energy equation and turbulence modeling equations are solved simultaneously with the continuity and momentum equations. Examples illustrating the nature of the solutions at the separation and reattachment points are presented.

Drela, M.↗
NASA NTRS1994

The Arctic Boundary Layer Expedition (ABLE-3B): July - August 1990

The Arctic Boundary Layer Expedition (ABLE) 3B used data from ground-based, aircraft, and satellite platforms to characterize the chemistry and dynamics of the troposphere in subarctic and Arctic regions of midcontinent and eastern Canada during July - August 1990. This paper reports the experimental design for ABLE 3B and a brief overview of results. The detailed results are presented in a series of papers in this issue. The chemical composition of the atmospheric mixed layer over remote tundra, boreal wetland, and forested environments was influenced by emissions of CH4 and nonmethane hydrocarbons from biogenic sources, emissions of gases and aerosols from local biomass burning, and transport of pollutants into the study areas from urban/industrial sources. Minimum concentrations of both trace gas and aerosol species in boundary layer air were associated with Arctic source areas. In the free troposphere the biospheric influence was undetectable, and major sources of chemical variability were related to long-range transport of pollutants into the study areas from biomass burning and industrial sources in Alaska and the Great Lakes regions, respectively. Minimum concentrations of both trace gas and aerosol species in the free troposphere were associated with a persistent, widespread air mass which both chemistry and air mass trajectory analyses suggested had originated in the tropical Pacific. Subsidence of air from the upper troposphere and lower stratosphere frequently enhanced ozone and influenced other trace gas and aerosol species at midtropospheric altitudes. The North American Arctic is a complex dynamical and chemical environment with considerable spatial and temporal variability in aerosol and trace gas concentrations. The use of atmospheric chemical indicators for climate change detection will require a much more comprehensive Arctic monitoring program than currently exists.

Harriss, R. C.↗
NASA NTRS1998

Numerical Modeling Studies of Wake Vortex Transport and Evolution Within the Planetary Boundary Layer

In support of the wake vortex effect of the Terminal Area Productivity program, we have put forward four tasks to be accomplished in our proposal. The first task is validation of two-dimensional wake vortex-turbulence interaction. The second task is investigation of three-dimensional interaction between wake vortices and atmospheric boundary layer (ABL) turbulence. The third task is ABL studies. The, fourth task is addition of a Klemp-Durran condition at the top boundary for TASS model. The accomplishment of these tasks will increase our understanding of the dynamics of wake vortex and improve forecasting systems responsible for air safety and efficiency. The first two tasks include following three parts: (a) Determine significant length scale for vortex decay and transport, especially the length scales associated with the onset of Crow instability (Crow, 1970); (b) Study the effects of atmospheric turbulence on the decay of the wake vortices; and (c) Determine the relationships between decay rate, transport properties and atmospheric parameters based on large eddy simulation (LES) results and the observational data. These parameters may include turbulence kinetic energy, dissipation rate, wind shear and atmospheric stratification. The ABL studies cover LES modeling of turbulence structure within planetary boundary layer under transition and stable stratification conditions. Evidences have shown that the turbulence in the stable boundary layer can be highly intermittent and the length scales of eddies are very small compared to those in convective case. We proposed to develop a nesting grid mesh scheme and a modified Klemp-Durran conditions (Klemp and Wilhelmson, 1978) at the top boundary for TASS model to simulate planetary boundary layer under stable stratification conditions. During the past year, our group has made great efforts to carry out the above mentioned four tasks simultaneously. The work accomplished in the last year will be described in the next section.

Lin, Yuh-Lang↗
NASA NTRS2007

On an Asymptotically Consistent Unsteady Interacting Boundary Layer

This paper develops the asymptotic matching of an unsteady compressible boundary layer to an inviscid flow. Of particular importance is the velocity injection or transpiration boundary condition derived by this theory. It is found that in general the transpiration will contain a slope of the displacement thickness and a time derivative of a density integral. The conditions under which the second term may be neglected, and its consistency with the established results of interacting boundary layer are discussed.

Bartels, Robert E.↗
NASA NTRS2013

Numerical Study of Pressure Fluctuations due to a Mach 6 Turbulent Boundary Layer

Direct numerical simulations (DNS) are used to examine the pressure fluctuations generated by a Mach 6 turbulent boundary layer with nominal freestream Mach number of 6 and Reynolds number of Re(sub t) approx. =. 464. The emphasis is on comparing the primarily vortical pressure signal at the wall with the acoustic freestream signal under higher Mach number conditions. Moreover, the Mach-number dependence of pressure signals is demonstrated by comparing the current results with those of a supersonic boundary layer at Mach 2.5 and Re(sub t) approx. = 510. It is found that the freestream pressure intensity exhibits a strong Mach number dependence, irrespective of whether it is normalized by the mean wall shear stress or by the mean pressure, with the normalized fluctuation amplitude being significantly larger for the Mach 6 case. Spectral analysis shows that both the wall and freestream pressure fluctuations of the Mach 6 boundary layer have enhanced energy content at high frequencies, with the peak of the premultiplied frequency spectrum of freestream pressure fluctuations being at a frequency of omega(delta)/U(sub infinity) approx. = 3.1, which is more than twice the corresponding frequency in the Mach 2.5 case. The space-time correlations indicate that the pressure-carrying eddies for the higher Mach number case are of smaller size, less elongated in the spanwise direction, and convect with higher convection speeds relative to the Mach 2.5 case. The demonstrated Mach-number dependence of the pressure field, including radiation intensity, directionality, and convection speed, is consistent with the trend exhibited in experimental data and can be qualitatively explained by the notion of "eddy Mach wave" radiation.

Duan, Lian↗
NASA NTRS1989

Performance of the active sidewall boundary-layer removal system for the Langley 0.3-meter Transonic Cryogenic Tunnel

A performance evaluation of an active sidewall boundary-layer removal system for the Langley 0.3-m Transonic Cryogenic Tunnel (TCT) was evaluated in 1988. This system uses a compressor and two throttling digital valves to control the boundary-layer mass flow removal from the tunnel. The compressor operates near the maximum pressure ratio for all conditions. The system uses a surge prevention and flow recirculation scheme. A microprocessor based controller is used to provide the necessary mass flow and compressor pressure ratio control. Initial tests on the system indicated problems in realizing smooth mass flow control while running the compressor at high speed and high pressure ratios. An alternate method has been conceived to realize boundary-layer mass flow control which avoids the recirculation of the compressor mass flow and operation near the compressor surge point. This scheme is based on varying the speed of the compressor for a sufficient pressure ratio to provide needed mass flow removal. The system has a mass flow removal capability of about 10 percent of test section flow at M = 0.3 and 4 percent at M = 0.8. The system performance has been evaluated in the form of the compressor map, and compressor tunnel interface characteristics covering most of the 0.3-m TCT operational envelope.

Balakrishna, S.↗
NASA NTRS2001

An Innovative Flow-Measuring Device: Thermocouple Boundary Layer Rake

An innovative flow-measuring device, a thermocouple boundary layer rake, was developed. The sensor detects the flow by using a thin-film thermocouple (TC) array to measure the temperature difference across a heater strip. The heater and TC arrays are microfabricated on a constant-thickness quartz strut with low heat conductivity. The device can measure the velocity profile well into the boundary layer, about 65 gm from the surface, which is almost four times closer to the surface than has been possible with the previously used total pressure tube.

Hwang, Danny P.↗
NASA NTRS1977

Boundary layer integral matrix procedure: Verification of models

The three turbulent models currently available in the JANNAF version of the Aerotherm Boundary Layer Integral Matrix Procedure (BLIMP-J) code were studied. The BLIMP-J program is the standard prediction method for boundary layer effects in liquid rocket engine thrust chambers. Experimental data from flow fields with large edge-to-wall temperature ratios are compared to the predictions of the three turbulence models contained in BLIMP-J. In addition, test conditions necessary to generate additional data on a flat plate or in a nozzle are given. It is concluded that the Cebeci-Smith turbulence model be the recommended model for the prediction of boundary layer effects in liquid rocket engines. In addition, the effects of homogeneous chemical reaction kinetics were examined for a hydrogen/oxygen system. Results show that for most flows, kinetics are probably only significant for stoichiometric mixture ratios.

Bonnett, W. S.↗
NASA NTRS2007

From Disturbances to Instabilities, to Breakdown to Turbulence: The Physics of Transition in Boundary Layers

In order to understand the end-stages of boundary layer transition in low as well as high disturbance environments it is desirable to establish a unified view of the sequences of physico-mathematical phenomena that lead from laminar flow to self-sustained "bursting" in wall turbulence. The dominant driving disturbances: oncoming free turbulence, unsteady pressure fields, inhomogeneous density fields, inhomogeneities in wall geometry, all force disturbed motions within the boundary layer via multiple competitive receptivity mechanisms. For small disturbances, a sequence of instabilities then leads to sporadic local bursting very near the wall which can sustain turbulence. The local seeds of turbulence then somehow propagate to engulf quite rapidly the surrounding disturbed but still laminar regions.

Morkovia, Mark V.↗
NASA NTRS2022

Hypersonic Boundary-Layer Instabilities over Ogive-Cylinder Models

Computational investigations of an ogive-cylinder geometry with varying nosetips at zero degrees angle of attack are presented. The model geometry and conditions are selected to match experiments conducted in the Air Force Research Laboratory (AFRL) Mach 6 Ludwieg Tube. Five nosetips of interest were selected for the computational studies herein: two sharp ogives, two blunt ogives, and one hemispherical nosetip. Computations are performed at a freestream Reynolds number of 7.01 × 10 6 m -1 . Each sharp and blunt tip ogives had a 14 and 28 degree version for the tip angles. A cylindrical section follows the nosetip, resulting in a meter long model such as in the experiments. The laminar flow solutions are analyzed. The boundary-layer-edge properties and the velocity and temperature profiles are compared across streamwise locations aft of the ogive-cylinder junction. The blunt nosetips induce an entropy layer that envelopes the boundary-layer profiles. Modal stability analysis identifies most amplified frequencies corresponding to Mack’s second modes that agree with experimental results for the sharp tips. Similar to the experimental measurements based on wall-mounted pressure sensors, no unstable modes are found for the blunt models. Nonmodal analysis revealed a broadband set of disturbances present for the blunter tips, in agreement with experimental observations. Flow perturbation contours of most amplified planar and oblique disturbances are shown to qualitatively match wind tunnel Schlieren images, with a switch from rope-like to elongated structures, i.e., from high frequency Mack’s second modes to low frequency Mack’s first modes, as the nosetip angle is increased for the sharp tip, and from boundary-layer to entropy-layer disturbances as the bluntness is increased.

Boundary layer transition↗
NASA NTRS1979

Boundary layer thermal stresses in angle-ply composite laminates

Boundary-layer thermal stress singularities and distributions of angle-ply composite laminates under uniform thermal loading are investigated through a system of sixth-order governing partial differential equations developed with the aid of the anisotropic elasticity field equations and Lekhnitskii's complex stress functions. Results are presented for cases of various angle-ply graphite/epoxy laminates, and it is shown that the boundary-layer thickness depends on the degree of anisotropy of each individual lamina, thermomechanical properties of each ply, and the relative thickness of adjacent layers.

Wang, S. S.↗
NASA NTRS2021

Hypersonic Boundary-Layer Instabilities over Ogive-Cylinder Models

Computational investigations of an ogive-cylinder geometry with varying nosetips at zero degrees angle of attack are presented. The model geometry and conditions are selected to match experiments conducted in the Air Force Research Laboratory (AFRL) Mach 6 Ludwieg Tube. Five nosetips of interest were selected for the computational studies herein: two sharp ogives, two blunt ogives, and one hemispherical nosetip. Computations are performed at a freestream Reynolds number of 7.01 × 10 6 m -1 . Each sharp and blunt tip ogives had a 14 and 28 degree version for the tip angles. A cylindrical section follows the nosetip, resulting in a meter long model such as in the experiments. The laminar flow solutions are analyzed. The boundary-layer-edge properties and the velocity and temperature profiles are compared across streamwise locations aft of the ogive-cylinder junction. The blunt nosetips induce an entropy layer that envelopes the boundary-layer profiles. Modal stability analysis identifies most amplified frequencies corresponding to Mack’s second modes that agree with experimental results for the sharp tips. Similar to the experimental measurements based on wall-mounted pressure sensors, no unstable modes are found for the blunt models. Nonmodal analysis revealed a broadband set of disturbances present for the blunter tips, in agreement with experimental observations. Flow perturbation contours of most amplified planar and oblique disturbances are shown to qualitatively match wind tunnel Schlieren images, with a switch from rope-like to elongated structures, i.e., from high frequency Mack’s second modes to low frequency Mack’s first modes, as the nosetip angle is increased for the sharp tip, and from boundary-layer to entropy-layer disturbances as the bluntness is increased.

Boundary layer transition↗
NASA NTRS1984

Simulation of blunt-fin-induced shock wave and turbulent boundary-layer interaction

A supersonic flow over a blunt fin mounted on a flat plate is numerically simulated. The fin shock causes the boundary layer to separate and results in a complicated, three-dimensional shockwave and boundary-layer interaction. The computed result is in good agreement with the measured pressure on the fin and the flat plate. The main features, such as peak pressure on the fin leading edge and a double peak pressure on the plate, are closely predicted. The role of the horseshoe vortex is discussed. The vortex leads to the development of high-speed flow, and, hence, low-pressure regions on the fin and the plate. Different thicknesses of the incoming boundary layer have been studied. Varying the thicknesses by an order of magnitude shows that the size of the horseshoe vortex and therefore the spatial extent of the interaction are inviscid-dominated, and are weakly dependent on the Reynolds number. Colored graphics are used to show details of the interaction flow field.

Hung, C.-M.↗
NASA NTRS2014

A Vortical Dawn Flank Boundary Layer for Near-Radial IMF: Wind Observations on 24 October 2001

We present an example of a boundary layer tailward of the dawn terminator which is entirely populated by rolled-up flow vortices. Observations were made by Wind on 24 October 2001 as the spacecraft moved across the region at the X plane approximately equal to −13 Earth radii. Interplanetary conditions were steady with a near-radial interplanetary magnetic field (IMF). Approximately 15 vortices were observed over the 1.5 hours duration of Wind's crossing, each lasting approximately 5 min. The rolling up is inferred from the presence of a hot tenuous plasma being accelerated to speeds higher than in the adjoining magnetosheath, a circumstance which has been shown to be a reliable signature of this in single-spacecraft observations. A blob of cold dense plasma was entrained in each vortex, at whose leading edge abrupt polarity changes of field and velocity components at current sheets were regularly observed. In the frame of the average boundary layer velocity, the dense blobs were moving predominantly sunward and their scale size along the X plane was approximately 7.4 Earth radii. Inquiring into the generation mechanism of the vortices, we analyze the stability of the boundary layer to sheared flows using compressible magnetohydrodynamic Kelvin-Helmholtz theory with continuous profiles for the physical quantities. We input parameters from (i) the exact theory of magnetosheath flow under aligned solar wind field and flow vectors near the terminator and (ii) the Wind data. It is shown that the configuration is indeed Kelvin-Helmholtz (KH) unstable. This is the first reported example of KH-unstable waves at the magnetopause under a radial IMF.

Magnetosheath↗
NASA NTRS1992

A compressible boundary layer algorithm for use with SINDA '85

It is useful to interface a high-speed-flow solution and SINDA to analyze the thermal behavior of systems that include both conduction and high speed flows. When interfacing a high-speed-flow solution to SINDA, it may be necessary to include the viscous effects in the energy equations. Boundary layer effects of interest include heat transfer coefficients (including convection and viscous dissipation) and friction coefficients. To meet this need, a fast, uncoupled, compressible, two-dimensional, boundary layer algorithm was developed that can model flows with and without separation. This algorithm was used as a subroutine with SINDA. Given the core flow properties and the wall heat flux from SINDA, the boundary layer algorithm returns a wall temperature to SINDA and boundary layer algorithm are iterated until they predict the same wall temperature.

Sakowski, Barbara↗