Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “backing layers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 991 records · Page 55

Charge collection efficiency in back-illuminated Charge-Coupled Devices

Low noise CCDs fully-depleted up to 675 micrometers have been identified as a unique tool for Dark Matter searches and low energy neutrino physics. The charge collection efficiency (CCE) for these detectors is a critical parameter for the performance of future experiments. We present here a new technique to characterize CCE in back-illuminated CCDs based on soft X-rays. This technique is used to characterize two different detector designs. The results demonstrate the importance of the backside processing for detection near threshold, showing that a recombination layer of a few microns significantly distorts the low energy spectrum. The studies demonstrate that the region of partial charge collection can be reduced to less than 1 micrometer thickness with adequate backside processing.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Full-range electrical characteristics of WS{sub 2} transistors

We fabricated transistors formed by few layers to bulk single crystal WS{sub 2} to quantify the factors governing charge transport. We established a capacitor network to analyze the full-range electrical characteristics of the channel, highlighting the role of quantum capacitance and interface trap density. We find that the transfer characteristics are mainly determined by the interplay between quantum and oxide capacitances. In the OFF-state, the interface trap density (<10{sup 12} cm{sup –2}) is a limiting factor for the subthreshold swing. Furthermore, the superior crystalline quality and the low interface trap density enabled the subthreshold swing to approach the theoretical limit on a back-gated device on SiO{sub 2}/Si substrate.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Characterizing Differences in the Aerosol Plume and Cloud Structure over Ascension Island During the 2016 and 2017 Biomass Burning Seasons

Marine boundary layer clouds, including the transition from stratocumulus to cumulus, are poorly represented in numerical weather prediction and general circulation models. In many cases, the complex physical relationships between marine boundary cloud morphology and the environmental conditions in which the clouds exist are not well understood. Such uncertainties arise in the presence of biomass burning carbonaceous aerosol, as is the case over the southeast Atlantic Ocean. It is likely that the absorbing and heating properties of these aerosols influence the microphysical composition and macrophysical arrangement of marine stratocumulus and trade cumulus in this region; however, this has yet to be quantified. The deployment of the Atmospheric Radiation Measurement Mobile Facility #1 (AMF1) in support of LASIC (Layered Atlantic Smoke Interactions with Clouds) provided a unique opportunity to collect observations of cloud and aerosol properties during two consecutive biomass burning seasons during July through October of 2016 and 2017 over Ascension Island (7.96 S, 14.35 W). Through the use of AMF1 observations, the Modern Era Retrospective Analysis for Research and Applications, version 2 (MERRA-2), and back trajectories from the Hybrid Single-Particle Lagrangian Integrated Trajectory model (HYSPLIT), it will be demonstrated that differences in the atmospheric circulation during the two years result in varying aerosol conditions over Ascension Island. When the aerosol plume is overhead, the aerosol loading is higher during the 2016 season as a result of a weaker subtropical high-pressure system. Furthermore, the aerosol plume originates from central Africa in 2016, but further south in 2017. Contrasts in the season-to-season and day-to-day aerosol loading are used to categorize boundary layer cloud and sub-cloud turbulence measurements above Ascension Island using the AMF1 Doppler lidar and cloud radar.

Collow, Allison B. Marquardt↗

Photoinduced Reconfiguration Cycle in a Molecular Adsorbate Layer Studied by Femtosecond Inner-Shell Photoelectron Spectroscopy

A time-resolved study of core-level chemical shifts in a monolayer of aromatic molecules reveals complex photoinduced reaction dynamics. The combination of electron spectroscopy for chemical analysis and ultrashort pulse excitation in the extreme ultraviolet allows performing time-correlated 4d-core-level spectroscopy of iodine atoms that probe the local chemical environment in the adsorbate molecule. The selectivity of the method unveils metastable molecular configurations that appear about 50 ps after the excitation and are efficiently quenched back to the ground state.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

LaCrO3 heteroepitaxy on SrTiO3(001) by molecular beam epitaxy

Stoichiometric, epitaxial LaCrO3 films have been grown on TiO2-terminated SrTiO3(001) substrates by molecular beam epitaxy using O2 as the oxidant. Film growth occurred in a layer-by-layer fashion, giving rise to structurally excellent films and surfaces which preserve the step-terrace structure of the substrate. The critical thickness is in excess of 500 Å. Near-surface Cr(III) is highly susceptible to further oxidation to Cr(V), leading to the formation of a disordered phase upon exposure to atomic oxygen. Recovery of the original epitaxial LaCrO3 phase is readily achieved by vacuum annealing.

36 MATERIALS SCIENCE↗

Moisture Corrosion of LiH: A Kinetic Investigation by DRIFT Spectroscopy

Lithium hydride (LiH) is a unique, ionic compound with applications in a variety of industries. Unfortunately, LiH is very reactive toward H 2 O even at ppm levels, forming oxide (Li 2 O) and hydroxide (LiOH) corrosion layers while outgassing H 2 . An effective means to eliminate unwanted outgassing is vacuum-heating to convert LiOH into Li 2 O, although subsequent re-exposure to moisture during transport/handling reconverts some Li 2 O back to LiOH. A corrosion growth model for previously vacuum-baked LiH is necessary for long-term prediction of the hydrolysis of LiH. In this work, a para-linear hydroxide corrosion growth model is proposed for the reaction of previously vacuum-baked LiH samples with moisture. This model, composed of two competing diffusion reaction fronts at the LiOH/Li 2 O and Li 2 O/LiH interfaces, is validated experimentally by subjecting a previously vacuum-baked polycrystalline LiH sample to 35 ppm of H 2 O at room temperature while monitoring the corrosion growth as a function of time with diffuse-reflectance infrared Fourier transform (DRIFT) spectroscopy. The para-linear growth model for the hydrolysis of previously vacuum-baked LiH proposed in this report can also serve as a template for the hydrolysis of other hygroscopic oxides grown on metal or metal hydride substrates.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Evaluation of Hanford Supernatant Waste Evaporation

Storage space within Hanford’s double shell tanks is running low, with only an approximate 4.1 Mgal of space remaining. Construction of additional storage space is not a pursuable option, but treatment of the waste via vacuum evaporation may be used to reduce the waste volume and increase the available amount of free space. However, without proper care and consideration, concentrating the waste may lead to harmful effects such as excessive solids generation, growth in liquid density and ionic concentration, and development of aggressive properties in the solution. OLI Studio was used to simulate a subset of DSTs using BBI ionic concentrations to generate recipes of every tank’s supernatant layer. Vacuum evaporation was performed by taking each simulated solution and bringing it to 50°C under a pressure of 60 Torr, after which the vapor phase was removed from the simulation, and the solution was brought back to ambient temperature and pressure. Several million gallons of space were created, and only about 100-200 kgal of solids were precipitated during evaporation. Minimal changes to the solution’s pitting factor occurred, and no solution is expected to develop aggressive characteristics due to evaporation. Although a theoretical result is provided, it is unique to the specific temperature and pressure value chosen for the simulation, and future transfers of waste are expected to cause changes in waste properties, which would cause the OLI recipes to lose accuracy. Though the results are not anticipated to be used as a target value or a guide, as an exercise, they show that the extent of volume gains could be equivalent to the construction of new DSTs.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Particle distributions in a two-dimensional reconnection field geometry

In order to understand space phase density variations near the magnetopause and in the geomagnetic tail, particle trajectories in a two-dimensional steady state reconnection field geometry are studied by tracing particles from a spacecraft position back in time. The distribution function at the spacecraft is calculated using Liouville's theorem and known distribution functions in the source regions. It is found, in particular, that multiple ion beams in the plasma sheet boundary layer are a natural consequence of reconnection. In the center of the central plasma sheet, the omnidirectional flux of keV ions should be at a minimum. The depth of this minimum is very large near the neutral point but decreases as the distance from the neutral point increases.

Gurran, D. B.↗

Is the Venusian lithosphere subducting?

Using data collected by the Magellan spacecraft, we are exploring the hypothesis that the cooler and more rigid outer layer of Venus (i.e., the lithosphere) is sinking (subducting) into the interior of Venus. If this process is occurring, it provides a mechanism for cooling the interior of Venus and also for recycling the lighter crustal rocks back into the interior. In addition, since subduction zones drive the plate tectonic motion on the Earth, evidence for lithospheric subduction on Venus raises the possibility of limited plate tectonic-like activity on Venus.

Sandwell, David T.↗

Pilot protection for the X-15 aircraft

The MC-2 pressure suit described in this paper is a lightweight, nonrigid omnienvironmental garment. It consists of a number of integrated layers, each performing a specific function in the complete assembly. The suit assembly to be used in the X-15 research vehicle includes a modified MA-3 helmet and a suit-helmet controller in a back-pack configuration.

Vail, Edwin G↗

Heating and Cooling Efficiency for Homes

Over 40 years ago, NASA developed Radiant Barrier technology to protect astronauts in the Apollo Program from temperatures that ranged from 250 F above to 400 F below zero Fahrenheit. This feat in temperature control technology enabled the astronauts to work inside the Apollo Command Module wearing short-sleeve shirts, with temperatures similar to those of a regular business office. The Radiant Barrier has been applied to virtually all spacecraft since then, including unmanned spacecraft with delicate instruments that need protection from temperature extremes. It is also applied to the astronauts space suits, protecting them during space walks. Made of aluminized polymer film, the Radiant Barrier both bars and lets in heat to maintain a consistent temperature in an environment where ordinary insulation methods will not suffice. The aluminization of the material provides a reflective surface that keeps more than 95 percent of the radiated energy in space from reaching the spacecraft s interior. In space suits, the thin and flexible material reflects the astronauts body heat back to them for warmth, while at the same time reflecting the sun s radiation away from them to keep them cool. Using conventional insulation, a space suit would have required a 7-foot-thick protective layer.

Source record↗

Low temperature recovery of OFF-state stress induced degradation of AlGaN/GaN high electron mobility transistors

Thermal annealing is a widely used strategy to enhance semiconductor device performance. However, the process is complex for multi-material multi-layered semiconductor devices, where thermoelastic stresses from lattice constant and thermal expansion coefficient mismatch may create more defects than those annealed. We propose an alternate low temperature annealing technique, which utilizes the electron wind force (EWF) induced by small duty cycle high density pulsed current. To demonstrate its effectiveness, we intentionally degrade AlGaN/GaN high electron mobility transistors (HEMTs) with accelerated OFF-state stressing to increase ON-resistance ∼182.08% and reduce drain saturation current ∼85.82% of pristine condition at a gate voltage of 0 V. We then performed the EWF annealing to recover the corresponding values back to ∼122.21% and ∼93.10%, respectively. The peak transconductance, degraded to ∼76.58% of pristine at the drain voltage of 3 V, was also recovered back to ∼92.38%. This recovery of previously degraded transport properties is attributed to approximately 80% recovery of carrier mobility, which occurs during EWF annealing. We performed synchrotron differential aperture x-ray microscopy measurements to correlate these annealing effects with the lattice structural changes. We found a reduction of lattice plane spacing of (001) planes and stress within the GaN layer under the gate region after EWF annealing, suggesting a corresponding decrease in defect density. Application of this low-temperature annealing technique for in-operando recovery of degraded electronic devices is discussed.

Physics↗

Carbon and nitrogen abundance determinations from transition layer lines

For red giants a smooth increase in the nitrogen to carbon abundance ratio for increasing B-V as is expected for the first dredge up phase when the outer convection zone deepens is found. An average increase in the nitrogen to silicon ratio for B-V = 0.6 which goes back to almost solar values for cool giants with B - V approximately 1.0 is reported. It looks as if Si would be enriched for deeper mixing contrary to expectations from standard evolution theory.

Boehm-Vitense, Erika↗

Ultrasonic Monitoring of Ply Crack and Delamination Formation in Composite Tube Under Torsion Load

As a simple model of a rotor spar, a circular graphite-epoxy composite laminate cylinder was subjected to cyclic torsional load. The test section of the cylindrical specimen varied from four to six plies of plus or minus 45 degree fibers, due to intentional ply overlaps and gaps. A layer of 13-micrometer Teflon film was inserted between plies at three locations to serve as delamination initiators. A commercial X-Y scanner was mounted to the load frame to enable ultrasonic inspection without removing the specimen. A focused immersion probe was mounted in a captive water column with a rugged Nitrile membrane tip, which was coupled to the cylinder using a mist of soapy water. The transducer was aligned normal to the cylinder surface using the X-axis. Scanning was performed along the length of the specimen with the Y-axis and the specimen was incrementally rotated by the torsion head of the load frame. After 350k cycles of torsion, several linear 45 degree diagonal indications appeared as 5-40% attenuation of the back wall echo, with no apparent echoes from the interior of the composite, suggesting through-ply cracks in the innermost ply. Crack indications grew and new cracks appeared as torsion cycling continued. Internal reflections from delaminations associated with the growing ply cracks appeared after 500k cycles. Three areas of extensive multi-layer delaminations appeared after 1150k cycles. Failure of the specimen occurred at 1600k cycles. The observed progressive damage was not associated with the Teflon inclusions. Concurrent thermographic measurements provided lower resolution confirmation of the damage observed.

Johnston, P. H.↗

Hybrid Active/Passive Control of Sound Radiation from Panels with Constrained Layer Damping and Model Predictive Feedback Control

There has been considerable interest over the past several years in applying feedback control methods to problems of structural acoustics. One problem of particular interest is the control of sound radiation from aircraft panels excited on one side by a turbulent boundary layer (TBL). TBL excitation appears as many uncorrelated sources acting on the panel, which makes it difficult to find a single reference signal that is coherent with the excitation. Feedback methods have no need for a reference signal, and are thus suited to this problem. Some important considerations for the structural acoustics problem include the fact that the required controller bandwidth can easily extend to several hundred Hertz, so a digital controller would have to operate at a few kilohertz. In addition, aircraft panel structures have a reasonably high modal density over this frequency range. A model based controller must therefore handle the modally dense system, or have some way to reduce the bandwidth of the problem. Further complicating the problem is the fact that the stiffness and dynamic properties of an aircraft panel can vary considerably during flight due to altitude changes resulting in significant resonant frequency shifts. These considerations make the tradeoff between robustness to changes in the system being controlled and controller performance especially important. Recent papers concerning the design and implementation of robust controllers for structural acoustic problems highlight the need to consider both performance and robustness when designing the controller. While robust control methods such as H1 can be used to balance performance and robustness, their implementation is not easy and requires assumptions about the types of uncertainties in the plant being controlled. Achieving a useful controller design may require many tradeoff studies of different types of parametric uncertainties in the system. Another approach to achieving robustness to plant changes is to make the controller adaptive. For example, a mathematical model of the plant could be periodically updated as the plant changes, and the feedback gains recomputed from the updated model. To be practical, this approach requires a simple plant model that can be updated quickly with reasonable computational requirements. A recent paper by the authors discussed one way to simplify a feedback controller, by reducing the number of actuators and sensors needed for good performance. The work was done on a tensioned aircraft-style panel excited on one side by TBL flow in a low speed wind tunnel. Actuation was provided by a piezoelectric (PZT) actuator mounted on the center of the panel. For sensing, the responses of four accelerometers, positioned to approximate the response of the first radiation mode of the panel, were summed and fed back through the controller. This single input-single output topology was found to have nearly the same noise reduction performance as a controller with fifteen accelerometers and three PZT patches. This paper extends the previous results by looking at how constrained layer damping (CLD) on a panel can be used to enhance the performance of the feedback controller thus providing a more robust and efficient hybrid active/passive system. The eventual goal is to use the CLD to reduce sound radiation at high frequencies, then implement a very simple, reduced order, low sample rate adaptive controller to attenuate sound radiation at low frequencies. Additionally this added damping smoothes phase transitions over the bandwidth which promotes robustness to natural frequency shifts. Experiments were conducted in a transmission loss facility on a clamped-clamped aluminum panel driven on one side by a loudspeaker. A generalized predictive control (GPC) algorithm, which is suited to online adaptation of its parameters, was used in single input-single output and multiple input-single output configurations. Because this was a preliminary look at the potential constrained layer damping for adaptive control, static feedback control with no online adaptation was used. Two configurations of CLD in addition to a bare panel configuration were studied. For each CLD configuration, two sensor arrangements for the feedback controller were compared. The first arrangement used fifteen accelerometers on the panel to estimate the responses of the first six radiation modes of the panel. The second sensor arrangement was simpler, using the summed responses of only four accelerometers to approximate the response of the first radiation mode of the panel. In all cases a PZT patch was mounted at the center of the panel for control input. The performance of the controller was quantified using the responses of the fifteen accelerometers on the panel to estimate radiated sound power. The paper begins with a brief discussion of the GPC algorithm and the experimental setup. The experimental results are discussed next, comparing the CLD and sensor configurations, followed by discussion and conclusions.

Cabell, Randolph H.↗

The circulation of the Dead Sea brine in the regional aquifer

It is known that Ca-chloride brines have circulated between the lakes and the adjacent aquifers throughout the history of the Dead Sea lacustrine-hydrology system. Here, the Ein-Qedem (EQ) hydrothermal saline springs system discharging at the western shores of the modern Dead Sea is the modern manifestation of this essential and continuous process. The EQ springs comprise the most significant source of Ca-chloride brine that currently discharges into the lake. The chemical composition of EQ brine has remained virtually uniform during the past ca. 40 yr, indicating that the brine represents a large groundwater reservoir. The EQ brine evolved from ancient Ca-chloride brine that occupied the tectonic depression of the Dead Sea Basin during the Quaternary. During this period, the composition of lake's brine was affected by mixing with freshwater and formation of primary minerals. Based on chronological and geochemical data, we argue that the EQ brine comprises the epilimnetic solution of last glacial Lake Lisan that penetrated and circulated through the adjacent Judea Group aquifer. 14 C and 81 Kr dating indicates recharge ages spanning the time interval of similar to 40-20 ka, coinciding with the period when the lake reached its highest stand (of similar to 200 +/- 30 m below msl, at similar to 31-17.4 ka) and maintained a stable layered (stratified) configuration for a period of several ten thousand years. The presented evidence suggests that the circulation of the Ca-chloride brine involves penetration into the aquifer during high stands (EQ brine recharge) and its discharge back into the lake during the modern low stands (similar to 400 to 430 m below msl). Accordingly, the mechanism of brine circulation between the lake and the marginal aquifers is related to the long-term hydro-climate history of the Dead Sea basin and its vicinity.

58 GEOSCIENCES↗

Giant energy storage and power density negative capacitance superlattices

Dielectric electrostatic capacitors, because of their ultrafast charge-discharge, are desirable for high-power energy storage applications. Along with ultrafast operation, on-chip integration can enable miniaturized energy storage devices for emerging autonomous microelectronics and microsystems. Moreover, state-of-the-art miniaturized electrochemical energy storage systems-microsupercapacitors and microbatteries-currently face safety, packaging, materials and microfabrication challenges preventing on-chip technological readiness, leaving an opportunity for electrostatic microcapacitors. Here, in this study, we report record-high electrostatic energy storage density (ESD) and power density, to our knowledge, in HfO 2 -ZrO 2 -based thin film microcapacitors integrated into silicon, through a three-pronged approach. First, to increase intrinsic energy storage, atomic-layer-deposited antiferroelectric HfO 2 -ZrO 2 films are engineered near a field-driven ferroelectric phase transition to exhibit amplified charge storage by the negative capacitance effect, which enhances volumetric ESD beyond the best-known back-end-of-the-line-compatible dielectrics (115 J cm -3 ). Second, to increase total energy storage, antiferroelectric superlattice engineering scales the energy storage performance beyond the conventional thickness limitations of HfO 2 -ZrO 2 -based (anti)ferroelectricity (100-nm regime). Third, to increase the storage per footprint, the superlattices are conformally integrated into three-dimensional capacitors, which boosts the areal ESD nine times and the areal power density 170 times that of the best-known electrostatic capacitors: 80 mJ cm -2 and 300 kW cm -2 , respectively. This simultaneous demonstration of ultrahigh energy density and power density overcomes the traditional capacity-speed trade-off across the electrostatic-electrochemical energy storage hierarchy. Furthermore, the integration of ultrahigh-density and ultrafast-charging thin films within a back-end-of-the-line-compatible process enables monolithic integration of on-chip microcapacitors, which can unlock substantial energy storage and power delivery performance for electronic microsystems.

25 ENERGY STORAGE↗