SEARCH · Engineering Papers

Results for “angle”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 991 records · Page 55

All sources NASA NTRS DOE OSTI

NASA NTRS1992

An aerodynamic design study of a series of lifting bodies at angles of attack from 10 to 53 degrees at Mach numbers from 2.30 to 4.62

The aerodynamic characteristics in the transition from high to low angles of attack at supersonic speeds have been experimentally and theoretically studied for a series of lifting bodies with various upper and lower surface camber designs. The configurations under consideration have a 75-degree swept delta planform with a rounded nose. Data obtained indicate that changes in the camber design cause some distinct changes in the aerodynamic characteristics that shoud be taken into account in the selection of a lifting body shape. The flat bottom designs with upper surface camber are found to provide greater drag for retardation at high angles of attack but are considerably out of trim longitudinally. The flat top designs with lower surface camber provide less drag at high angles of attack but can be more easily trimmed. Calculated results are found to be in good agreement with the experimental data.

Spearman, M. L.↗

NASA NTRS1992

Full-scale high angle-of-attack tests of an F/A-18

This paper presents an overview of high angle-of-attack tests of a full-scale F/A-18 in the 80- by 120-Foot Wind Tunnel of the National Full-Scale Aerodynamic Complex at NASA Ames Research Center at Moffett Field, California. A production aircraft was tested over an angle-of-attack range of 18 to 50 deg and at wind speeds of up to 100 knots. These tests had three primary test objectives. Pneumatic and mechanical forebody flow control devices were tested at full-scale and shown to produce significant yawing moments for lateral control of the aircraft at high angles of attack. Mass flow requirements for the pneumatic system were found to scale with freestream density and speed rather than freestream dynamic pressure. Detailed measurements of the pressures buffeting the vertical tail were made and spatial variations in the buffeting frequency were found. The LEX fence was found to have a significant effect on the frequency distribution on the outboard surface of the vertical fin. In addition to the above measurements, an extensive set of data was acquired for the validation of computational fluid dynamics codes and for comparison with flight test and small-scale wind tunnel test results.

Meyn, Larry A.↗

NASA NTRS1992

Thrust vectoring characteristics of the F-18 high alpha research vehicle at angles of attack from 0 to 70 deg

An investigation was conducted to determine the multiaxis thrust-vectoring characteristics of the F-18 High Alpha Research Vehicle (HARV). A 0.10-scale model was modified with hardware to simulate the three-vane thrust vectoring system of the F-18/HARV. This investigation was conducted at Mach numbers ranging from 0.30 to 0.70, at angles of attack from 0 to 70 deg, and nozzle-pressure ratios from 2.0 to approximately 5.0. Results indicate that the thrust vectoring system of F-18/HARV can successfully generate multiaxis thrust vectoring. During vectoring, resultant thrust-vector angles were always less than the corresponding geometric vane deflection angle and were accompanied by large thrust losses.

Asbury, Scott C.↗

NASA NTRS1992

Physics of pitch angle scattering and velocity diffusion. I - Theory

A general theory for the pitch angle scattering and velocity diffusion of particles in the field of a spectrum of waves in a magnetized plasma is presented. The test particle theory is used to analyze the particle motion. The form of diffusion surfaces is examined, and analytical expressions are given for the resonance width and bounce frequency. The resonance widths are found to vary strongly as a function of harmonic number. The resulting diffusion can be quite asymmetric with respect to pitch angle of 90 deg. The conditions for the onset of pitch angle scattering and energy diffusion are explained in detail. Some of the known shortcomings of the standard quasi-linear theory are also addressed, and ways to overcome them are shown. In particular, the often stated quasi-linear gap at 90 deg is found to exist only under very special cases. For instance, oblique wave propagation can easily remove the gap. The conditions for the existence of the gap are described in great detail. A new diffusion equation which takes into account the finite resonance widths is also discussed. The differences between this new theory and the standard resonance broadening theory is explained.

Karimabadi, H.↗

NASA NTRS1993

Flight and wind-tunnel calibrations of a flush airdata sensor at high angles of attack and sideslip and at supersonic Mach numbers

A nonintrusive airdata-sensing system was calibrated in flight and wind-tunnel experiments to an angle of attack of 70 deg and to angles of sideslip of +/- 15 deg. Flight-calibration data have also been obtained to Mach 1.2. The sensor, known as the flush airdata sensor, was installed on the nosecap of an F-18 aircraft for flight tests and on a full-scale F-18 forebody for wind-tunnel tests. Flight tests occurred at the NASA Dryden Flight Research Facility, Edwards, California, using the F-18 High Alpha Research Vehicle. Wind-tunnel tests were conducted in the 30- by 60-ft wind tunnel at the NASA LaRC, Hampton, Virginia. The sensor consisted of 23 flush-mounted pressure ports arranged in concentric circles and located within 1.75 in. of the tip of the nosecap. An overdetermined mathematical model was used to relate the pressure measurements to the local airdata quantities. The mathematical model was based on potential flow over a sphere and was empirically adjusted based on flight and wind-tunnel data. For quasi-steady maneuvering, the mathematical model worked well throughout the subsonic, transonic, and low supersonic flight regimes. The model also worked well throughout the angles-of-attack and -sideslip regions studied.

Moes, Timothy R.↗

NASA NTRS1993

Hypervelocity impact study: The effect of impact angle on crater morphology

The Space Power Institute (SPI) of Auburn University has conducted preliminary tests on the effects of impact angle on crater morphology for hypervelocity impacts. Copper target plates were set at angles of 30 deg and 60 deg from the particle flight path. For the 30 deg impact, the craters looked almost identical to earlier normal incidence impacts. The only difference found was in the apparent distribution of particle residue within the crater, and further research is needed to verify this. The 60 deg impacts showed marked differences in crater symmetry, crater lip shape, and particle residue distribution. Further research on angle effects is planned, because the particle velocities for these shots were relatively slow (7 km/s or less).

Crawford, Gary↗

NASA NTRS1992

On the distribution of pitch angles in external galactic spirals NGC 1232 and NGC 5457

A numerical method, originally developed to analyze the morphology of global and local structure in prototype galaxies, is modified for analyzing observed disk-shape galaxies. Two digitized spiral galaxies NGC 1232 and NGC 5457 with varying degrees of contrast between arm and interarm regions are analyzed. A synergism of partitioning methods and a geometric mean least-squares regression algorithm serves to isolate local arm segments, spurs, feathers, and secondary features and to measure their pitch angles and lengths. The global arms are actually highly disjointed, with arm segments frequently revealing pitch angles between 30 and 50 deg, certainly greater than those of the parent arms. Prominent spurs tend to exhibit a much greater pitch angle. The automated mathematical algorithm is shown to have negligible numerical biasing and could be applied to any number of spiral galaxies manifesting flocculent structure, either prototype or observed, and could possibly be used as a tool for classification of multiple-armed-type galaxies.

Russell, William S.↗

NASA NTRS1993

Flight and wind-tunnel calibrations of a flush airdata sensor at high angles of attack and sideslip and at supersonic Mach numbers

Moes, Timothy R.↗

NASA NTRS1992

Charge collection at large angles of incidence

Charge collection exhibited by p-n junctions, which have at least one small dimension, deviates from the geometric assumptions commonly used in SEU (single event upset) testing. The amount of charge collected did not increase with the secant of the angle of incidence. The number of events under the peak in the charge collection spectrum did not decrease as the cosine of the angle of incidence. Both the position of the peak and the number of events under the peak measured at a given angle of incidence depended upon which symmetry axis of the device was chosen to be the axis of rotation.

Mcnulty, P. J.↗

NASA NTRS1993

Lateral control at high angles of attack using pneumatic blowing through a chined forebody

Directional control through the use of pneumatic blowing was investigated on a generic subscale model with a chined forebody with blowing through a chine slot in a direction normal to the forebody surface. Comparisons are made with a vertical tail on and off, and with control through rudder deflection. Force and moment data were obtained for various blowing coefficients over a 0-75 deg alpha range, and flow visualization was also conducted in order to see qualitative effects on the flowfield. Blowing through a chined forebody generates yaw moments at large alpha where control surfaces lose their effectiveness; these moments are much larger than obtained by jet thrust alone, since the forebody flowfield is modified through the interaction of the jet with the chine vortices. Directional control increased with angle of attack for a given blowing coefficient until a maximum was reached. Further increases in angle of attack results in a rapid loss of effectiveness. For angles of attack above 60 deg, yaw moments are generated by simple jet thrust effect. The effectiveness of the pneumatic system depended on tail configuration.

Arena, A. S., Jr.↗

NASA NTRS1993

Electron cyclotron maser emission at oblique angles

Possible causes of observations of electron cyclotron maser emissions (ECMEs) at oblique angle (about 60 deg) to the magnetic field are investigated. The paper discusses general concepts of ECME in terms of resonant ellipses and considers electron distributions required to produce ECME at oblique angles, as well as the ways in which the most favorable of these distributions may be produced. A mechanism is proposed that might produce an appropriate 'spiraling beam' distribution, with a peak in velocity space at speed v - v(0) and pitch angle alpha = alpha(0) not equal to 0.

Melrose, D. B.↗

NASA NTRS1933

Wind tunnel research comparing lateral control devices, particularly at high angles of attack XI : various floating tip ailerons on both rectangular and tapered wings

Discussed here are a series of systematic tests being conducted to compare different lateral control devices with particular reference to their effectiveness at high angles of attack. The present tests were made with six different forms of floating tip ailerons of symmetrical section. The tests showed the effect of the various ailerons on the general performance characteristics of the wing, and on the lateral controllability and stability characteristics. In addition, the hinge moments were measured for the most interesting cases. The results are compared with those for a rectangular wing with ordinary ailerons and also with those for a rectangular wing having full-chord floating tip ailerons. Practically all the floating tip ailerons gave satisfactory rolling moments at all angles of attack and at the same time gave no adverse yawing moments of appreciable magnitude. The general performance characteristics with the floating tip ailerons, however, were relatively poor, especially the rate of climb. None of the floating tip ailerons entirely eliminated the auto rotational moments at angles of attack above the stall, but all of them gave lower moments than a plain wing. Some of the floating ailerons fluttered if given sufficiently large deflection, but this could have been eliminated by moving the hinge axis of the ailerons forward. Considering all points including hinge moments, the floating tip ailerons on the wing with 5:1 taper are probably the best of those which were tested.

Weick, Fred E↗

NASA NTRS1954

Airfoil section characteristics at high angles of attack

Information from the literature and from recent investigations is used herein to summarize briefly the effects of airfoil section parameters and flow variables on the aerodynamic characteristics of two-dimensional symmetrical airfoils at high angles of attack. The results presented indicate that airfoil thickness ratio, Reynolds number, Mach number, and surface roughness can all have an important effect on the maximum lift coefficient. The effect of surface roughness seems to be particularly important. Not only can surface roughness cause large decreases in maximum lift coefficient, but also the magnitudes of the effects of Reynolds number, Mach number, and airfoil thickness ratio are much reduced by surface roughness. Beyond the stall, changes in section thickness ratio appear to have little effect on the aerodynamic characteristics of airfoil sections. An investigation of one section through an angle-of-attack range of from 0° to 360° shows that the drag coefficient reaches a value of 2 at an angle of attack of 90°.

Laurence K Loftin, Jr↗

NASA NTRS1952

Experimental Investigation of Flow in an Annular Cascade of Turbine Nozzle Blades of Constant Discharge Angle

The experimental performance of turbine nozzle blades designed for a constant discharge angle was investigated at discharge hub Mach numbers of 1.18, 1.31, and 1.41. Flow characteristics are presented in terms of energy losses, angle gradients, and secondary flow effects. Blade efficiency decreased from 0.983 to 0.978 with increasing Mach number in the range investigated while angle variations in the loss regions became very large, indicating poorer blade performance than efficiency implies.

BOUNDARY LAYER CHARACTERISITCS-INTERNAL AERODYNAMI↗

NASA NTRS1955

Flight Measurements of Horizontal-Tail Loads on the Bell X-5 Research Airplane at a Sweep Angle of 58.7 Deg

A flight investigation was made at altitudes of 40,000, 25,000 and 15,000 feet to determine the horizontal-tail loads of the Bell X-5 research airplane at a sweep angle of 58.7 deg over the lift range of the airplane for Mach numbers from 0.61 to 1.00. The horizontal-tail loads were found to be nonlinear with lift throughout the lift ranges tested at all Mach numbers except at a Mach number of 1.00. The balancing tail loads reflected the changes which occur in the wing characteristics with increasing angle of attack. The nonlinearities were, in general, more pronounced at the higher angles of attack near the pitch-up where the balancing tail loads indicate that the wing-fuselage combination becomes unstable. No apparent effects of altitude on the balancing tail loads were evident over the comparable lift ranges of these tests at altitudes from 40,000 feet to 15,000 feet. Comparisons of balancing tail loads obtained from flight and windtunnel tests indicated discrepancies in absolute magnitudes, but the general trends of the data agree. Some differences in absolute magnitude may be accounted for by the tail load carried inboard of the strain-gage station and the load induced on the fuselage by the presence of the tail. These loads were not measured in flight.

Reed, Robert D↗

NASA NTRS1957

Flight Investigation at Low Angles of Attack to Determine the Longitudinal Stability and Control Characteristics of a Cruciform Canard Missile Configuration with a Low-Aspect-Ratio Wing and Blunt Nose at Mach Numbers from 1.2 to 2.1

A full- scale rocket-powered model of a cruciform canard missile configuration with a low- aspect - ratio wing and blunt nose has been flight tested by the Langley Pilotless Aircraft Research Division. Static and dynamic longitudinal stability and control derivatives of this interdigitated canard-wing missile configuration were determined by using the pulsed- control technique at low angles of attack and for a Mach number range of 1.2 to 2.1. The lift - curve slope showed only small nonlinearities with changes in control deflection or angle of attack but indicated a difference in lift- .curve slope of approximately 7 percent for the two control deflections of delta = 3.0 deg and delta= -0.3 deg . The large tail length of the missile tested was effective in producing damping in pitch throughout the Mach number range tested. The aerodynamic- center location was nearly constant with Mach number for the two control deflections but was shown to be less stable with the larger control deflection. The increment of lift produced by the controls was small and positive throughout the Mach number range tested, whereas the pitching moment produced by the controls exhibited a normal trend of reduced effectiveness with increasing Mach number.The effectiveness of the controls in producing angle of attack, lift, and pitching moment was good at all Mach numbers tested.

Brown, Clarence A , Jr↗

NASA NTRS1921

Angles of Attack and Air Speeds During Maneuvers

In seeking further information as to the nature of maneuvers and as to the maneuverability characteristics of airplanes, continuous measurements of the angles of attack and air speeds at several points along the wings have been made during spins and loops. Very striking results have been obtained with reference to the rolling velocity and the distribution of load in spins and the variation of the angle of attack in loops, a surprisingly large range of angle being experienced during slow loops. The flight tests and results are fully described in this report.

Warner, E P↗

NASA NTRS1933

Wind-tunnel research comparing lateral control devices, particularly at high angles of attack V : spoilers and ailerons on rectangular wings

This report covers the fifth of a series of systematic investigations in which lateral control devices are compared with particular reference to their effectiveness at high angles of attack. The present report deals with tests of spoilers and ordinary ailerons on rectangular Clark y wing models. In an effort to obtain satisfactory control throughout the entire angle-of-attack range that can be maintained in flight, various spoilers were tested in combination with two sizes of previously tested ordinary ailerons - one of average proportions and the other short and wide. In addition, one large spoiler was tested alone. It was found that when ailerons and spoilers are used together the full effect of both is not obtained if the spoilers are located directly in front of the ailerons. With the proper combination of spoiler and aileron, however, it is possible to obtain satisfactory rolling control up to high angles of attack (15 degrees to 20 degrees), together with favorable yawing moments and small control forces. A moderate amount of rolling control with favorable yawing moments and small control forces was obtained with the large spoiler alone.

Weick, Fred E↗