Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Waveform Data”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 991 records · Page 55

Comparison of analysis and experiment for dynamics of low-contact-ratio spur gears

Low-contact-ratio spur gears were tested in NASA gear-noise-rig to study gear dynamics including dynamic load, tooth bending stress, vibration, and noise. The experimental results were compared with a NASA gear dynamics code to validate the code as a design tool for predicting transmission vibration and noise. Analytical predictions and experimental data for gear-tooth dynamic loads and tooth-root bending stress were compared at 28 operating conditions. Strain gage data were used to compute the normal load between meshing teeth and the bending stress at the tooth root for direct comparison with the analysis. The computed and measured waveforms for dynamic load and stress were compared for several test conditions. These are very similar in shape, which means the analysis successfully simulates the physical behavior of the test gears. The predicted peak value of the dynamic load agrees with the measurement results within an average error of 4.9 percent except at low-torque, high-speed conditions. Predictions of peak dynamic root stress are generally within 10 to 15 percent of the measured values.

Oswald, Fred B.↗

A Software Platform for Post-Processing Waveform-Based NDE

Ultrasonic, microwave, and terahertz nondestructive evaluation imaging systems generally require the acquisition of waveforms at each scan point to form an image. For such systems, signal and image processing methods are commonly needed to extract information from the waves and improve resolution of, and highlight, defects in the image. Since some similarity exists for all waveform-based NDE methods, it would seem a common software platform containing multiple signal and image processing techniques to process the waveforms and images makes sense where multiple techniques, scientists, engineers, and organizations are involved. This presentation describes NASA Glenn Research Center's approach in developing a common software platform for processing waveform-based NDE signals and images. This platform is currently in use at NASA Glenn and at Lockheed Martin Michoud Assembly Facility for processing of pulsed terahertz and ultrasonic data. Highlights of the software operation will be given. A case study will be shown for use with terahertz data. The authors also request scientists and engineers who are interested in sharing customized signal and image processing algorithms to contribute to this effort by letting the authors code up and include these algorithms in future releases.

Roth, Donald J.↗

Bandwidth-Efficient Communication through 225 MHz Ka-band Relay Satellite Channel

The communications and navigation space infrastructure of the National Aeronautics and Space Administration (NASA) consists of a constellation of relay satellites (called Tracking and Data Relay Satellites (TDRS)) and a global set of ground stations to receive and deliver data to researchers around the world from mission spacecraft throughout the solar system. Planning is underway to enhance and transform the infrastructure over the coming decade. Key to the upgrade will be the simultaneous and efficient use of relay transponders to minimize cost and operations while supporting science and exploration spacecraft. Efficient use of transponders necessitates bandwidth efficient communications to best use and maximize data throughput within the allocated spectrum. Experiments conducted with NASA's Space Communication and Navigation (SCaN) Testbed on the International Space Station provides a unique opportunity to evaluate advanced communication techniques, such as bandwidth-efficient modulations, in an operational flight system. Demonstrations of these new techniques in realistic flight conditions provides critical experience and reduces the risk of using these techniques in future missions. Efficient use of spectrum is enabled by using high-order modulations coupled with efficient forward error correction codes. This paper presents a high-rate, bandwidth-efficient waveform operating over the 225 MHz Ka-band service of the TDRS System (TDRSS). The testing explores the application of Gaussian Minimum Shift Keying (GMSK), 248-phase shift keying (PSK) and 1632- amplitude PSK (APSK) providing over three bits-per-second-per-Hertz (3 bsHz) modulation combined with various LDPC encoding rates to maximize throughput. With a symbol rate of 200 Mbaud, coded data rates of 1000 Mbps were tested in the laboratory and up to 800 Mbps over the TDRS 225 MHz channel. This paper will present on the high-rate waveform design, channel characteristics, performance results, compensation techniques for filtering and equalization, and architecture considerations going forward for efficient use of NASA's infrastructure.

space communications↗

Inherent secure communications using lattice based waveform design

The wireless communications channel is innately insecure due to the broadcast nature of the electromagnetic medium. Many techniques have been developed and implemented in order to combat insecurities and ensure the privacy of transmitted messages. Traditional methods include encrypting the data via cryptographic methods, hiding the data in the noise floor as in wideband communications, or nulling the signal in the spatial direction of the adversary using array processing techniques. This work analyzes the design of signaling constellations, i.e. modulation formats, to combat eavesdroppers from correctly decoding transmitted messages. It has been shown that in certain channel models the ability of an adversary to decode the transmitted messages can be degraded by a clever signaling constellation based on lattice theory. This work attempts to optimize certain lattice parameters in order to maximize the security of the data transmission. These techniques are of interest because they are orthogonal to, and can be used in conjunction with, traditional security techniques to create a more secure communication channel.

97 MATHEMATICS AND COMPUTING↗

A new MicroTCA-based waveform digitizer for the Muon g-2 experiment

We present the design of a new $\mu$TCA-based waveform digitizer, which will be deployed in the Muon g-2 experiment at Fermilab and will allow our pileup identification requirement to be met. This digitizer features five independent channels, each with 12-bit, 800-MSPS digitization and a 1-Gbit memory buffer. The data storage and readout along with configuration are handled by six Xilinx Kintex-7 FPGAs. In addition, the digitizer is equipped with a mezzanine card for analog signal conditioning prior to digitization, further widening its range of possible applications. The performance results of this design are also presented, highlighting its $0.51 \pm 0.13$ mV intrinsic noise level and $< 22$ ps intrinsic timing resolution between channels. We believe that its performance, together with its flexible design, could be of interest to future experiments in search of a cost-effective waveform digitizer.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Bandwidth-Efficient Communication through 225 MHz Ka-band Relay Satellite Channel

The communications and navigation space infrastructure of the National Aeronautics and Space Administration (NASA) consists of a constellation of relay satellites (called Tracking and Data Relay Satellites (TDRS)) and a global set of ground stations to receive and deliver data to researchers around the world from mission spacecraft throughout the solar system. Planning is underway to enhance and transform the infrastructure over the coming decade. Key to the upgrade will be the simultaneous and efficient use of relay transponders to minimize cost and operations while supporting science and exploration spacecraft. Efficient use of transponders necessitates bandwidth efficient communications to best use and maximize data throughput within the allocated spectrum. Experiments conducted with NASA's Space Communication and Navigation (SCaN) Testbed on the International Space Station provides a unique opportunity to evaluate advanced communication techniques, such as bandwidth-efficient modulations, in an operational flight system. Demonstrations of these new techniques in realistic flight conditions provides critical experience and reduces the risk of using these techniques in future missions. Efficient use of spectrum is enabled by using high-order modulations coupled with efficient forward error correction codes. This paper presents a high-rate, bandwidth-efficient waveform operating over the 225 MHz Ka-band service of the TDRS System (TDRSS). The testing explores the application of Gaussian Minimum Shift Keying (GMSK), 2/4/8-phase shift keying (PSK) and 16/32- amplitude PSK (APSK) providing over three bits-per-second-per-Hertz (3 b/s/Hz) modulation combined with various LDPC encoding rates to maximize through- put. With a symbol rate of 200 M-band, coded data rates of 1000 Mbps were tested in the laboratory and up to 800 Mbps over the TDRS 225 MHz channel. This paper will present on the high-rate waveform design, channel characteristics, performance results, compensation techniques for filtering and equalization, and architecture considerations going forward for efficient use of NASA's infrastructure.

transmitters receivers↗

Challenges and Opportunities in Turning Large U.S. Archives of Analog Seismograms into a Modern Usable Resource

Abstract Quantitative seismology is based firmly on the analysis of actual ground motions, and the transition to digital recording in the 1980s enabled sophisticated new capabilities to extract useful results from waveforms. With some effort, these tools can also be applied to analog records. Focusing on assets available within U.S. institutions, we review the necessary steps and the challenges in enabling “data rescue”—that is, preserving the scientific information latent in large analog seismogram archives and making it usable. They include: determining what assets are available (the analog seismogram archives held by various institutions, with associated metadata on instrument responses, station locations, and timing information); developing a consensus on the top level of a triage process (which analog records most definitely should be rescued?); deciding the level of quality needed in copying original seismograms to media suitable for digitizing; assessing the relative merits of scanning and digitizing; and, the need for a community service in distributing scans and digital records, as they accumulate. The necessary level of effort can benefit from practical experience. For example, specific studies have used digitized versions of analog recordings to model earthquake sources and assess seismic hazard. Other studies have used them to gain experience with nuclear explosion signals recorded at regional distances, noting that regional signals enable explosions to be monitored down to levels much lower than those attainable teleseismically. The opportunities presented by large archives of analog seismograms include the insights they present to current and future seismologists studying earthquakes and explosions, into the practical areas of assessing seismic hazard, monitoring for test ban compliance down to low explosion yields—and prompt characterization of actual explosions should they occur, as well the traditional academic pursuit of a better understanding of earthquake physics.

Geochemistry & Geophysics↗

Soft x-ray shock loading and momentum coupling in meteorite and planetary materials.

X-ray momentum coupling coefficients, C{sub M}, were determined by measuring stress waveforms in planetary materials subjected to impulsive radiation loading from the Sandia National Laboratories Z-machine. Results from the velocity interferometry (VISAR) diagnostic provided limited equation-of-state data as well. Targets were iron and stone meteorites, magnesium rich olivine (dunite) solid and powder ({approx}5--300 {mu}m), and Si, Al, and Fe calibration targets. All samples were {approx}1 mm thick and, except for Si, backed by LiF single-crystal windows. The x-ray spectrum included a combination of thermal radiation (blackbody 170--237 eV) and line emissions from the pinch material (Cu, Ni, Al, or stainless steel). Target fluences 0.4--1.7 kJ/cm{sup 2} at intensities 43--260 GW/cm{sup 2} produced front surface plasma pressures 2.6--12.4 GPa. Stress waves driven into the samples were attenuating due to the short ({approx}5 ns) duration of the drive pulse. Attenuating wave impulse is constant allowing accurate C{sub M} measurements provided mechanical impedance mismatch between samples and the window are known. Impedance-corrected C{sub M} determined from rear-surface motion was 1.9--3.1 x 10{sup -5} s/m for stony meteorites, 2.7 and 0.5 x 10{sup -5} s/m for solid and powdered dunite, 0.8--1.4 x 10{sup -5}.

36 MATERIALS SCIENCE↗

Rock Valley Accelerated Weight Drop Seismic Data Processing and Picking of P-wave and S-wave Arrival Times

Rock Valley, in the southern end of the Nevada National Security Site, hosts a fault system that was responsible for a shallow (< 3 km below surface ) magnitude 3.7 earthquake in May 1993. In order to better understand this system, seismic properties of the shallow subsurface need to be better constrained. In April and May of 2021, accelerated weight drop (AWD) active-source seismic data were recorded in order to measure P- and S-wave travel-times for the area. This report describes the processing and phase picking of the recorded seismic waveforms. In total, we picked 7,982 P-wave arrivals at offsets up to ~2500 m, and 4,369 S-wave arrivals at offsets up to ~2200 m. These travel-time picks can be inverted for shallow P-wave and S-wave velocity structure in future studies.

58 GEOSCIENCES↗

Skylab altimeter observations over terrain

The author has identified the following significant results. Data obtained by Skylab radar altimeter (S193) over the continental U.S.A. for pass 1 of SL-3 were analyzed to relate radar return signal parameters such as range, power, and waveform to ground track terrain features. The altimeter, which was originally designed for ocean observations, performed predictably well over terrain with moderate to low relief. The maximum return from more complex areas corresponded usually to the lower flatter regions within the seven kilometer diameter footprint. Altimeter measured heights correlated with map topography with an rms deviation of + or - 30 m for terrain topography with large height dispersion (passes 1 and 28) and + or - 5 m for slowly varying terrain (passes 16, 17, and 18). Analysis of the waveform and statistical characteristics of the individual signals indicated that larger signal power was usually related to dominantly specular reflections from patches 100 m or larger. Results established the capability of a spacecraft altimeter system to observe characteristic radar signatures for different types of terrain within the bandwidth restrictions of the AGC and range tracker loops.

Shapiro, A.↗

The critical satellite technical issues of future pervasive broadband low-cost communication networks

The critical technical issues of signal waveform design, projected spacecraft technology, satellite launch options, and satellite cost are discussed for future pervasive broadband communication networks. With DPCM video signal encoding, 32 Mb/s user-to-user data rate per channel, 10% overhead, two orthogonal polarizations, and crosstalk loss limited to 1 dB, TFM permits about 75 channels/GHz of frequency allocation. The BOM (beginning of mission) weight and power of a baseline 400-channel multibeam satellite is about 1800 kg and 5000 W. Each 35 Mb/s channel can support 1 to 10 video channels. The weight and power estimates assume hardened digital logic, composite materials for a multibeam antenna structure, high-efficiency solar cells, batteries, and amplifiers. Based on a cost model for large communication satellites, the total space segment cost of two active satellites and one spare would be about $485 M.

Harvey, R. L.↗

The payload/shuttle-data-communication-link handbook

Communication links between the Orbiter, payloads, and ground are described: end-to-end, hardline, S-band, Ku-band, TDRSS relay, waveforms, premodulation, subcarrier modulation, carrier modulation, transmitter power, antennas, the RF channel, system noise, received signal-to-noise spectral density, carrier-tracking loop, carrier demodulation, subcarrier demodulation, digital data detection, digital data decoding, and tandem link considerations.

Source record↗

Review of measurements of the RF spectrum of radiation from lightning

A review is presented of the measurements reported in the literature of the spectrum of electromagnetic radiation from lightning in the frequency range from 1 kHz to 1 GHz. Measurements have been made either by monitoring the power received at individual frequencies using a narrow bandwidth recording device tuned to the frequencies under investigation or by recording the transient (time dependent) radiation with a wide bandwidth device and then Fourier transforming the waveform to obtain a spectrum. Measurements of the first type were made extensively in the 1950’s and 1960’s and several composite spectra have been deduced by normalizing the data of different investigators to common units of bandwidth and distance. The composite spectra tend to peak near 5 kHz and then decrease roughly as (frequency).’ upto nearly 100 MHz where scatter in the data make the behaviour uncertain. Measurements of the second type have been reported for return strokes, the stepped leader and for some intracloud processes. The spectrum of first return strokes obtained in this manner is very similar to the composite spectra obtained from the narrowband measurements.

Lightning Spectrum↗

Review of measurements of the RF spectrum of radiation from lightning

A review is presented of the measurements reported in the literature of the spectrum of electromagnetic radiation from lightning in the frequency range from 1 kHz to 1 GHz. Measurements have been made either by monitoring the power received at individual frequencies using a narrow bandwidth recording device or by recording the transient (time dependent) radiation with a wide bandwidth device and then Fourier transforming the waveform to obtain a spectrum. Measurements of the first type were made extensively in the 1950's and 1960's and several composite spectra have been deduced by normalizing the data of different investigators to common units of bandwidth and distance. The composite spectra tend to peak near 5 kHz and then decrease roughly as 1/(frequency) up to nearly 100 MHz where scatter in the data make the behaviour uncertain. The spectrum obtained with measurements of the second type is similar. Recent experiments have extended the frequency range covered to several 10's of MHz and include spectra for return strokes, the stepped leader and for some intracloud processes. The spectrum of first return strokes obtained in this manner is very similar to the spectrum of the composite flash obtained from the narrowband measurements.

Radiation↗

Blade surface pressure measurement on a pusher propeller in flight

Unsteady aerodynamics of a pusher propeller operating in the wake of a pylon is investigated through analysis of flight test data. Twenty-two surface-mounted miniature pressure transducers were installed at the 75 and 90 percent radius locations on a propeller blade on a test-bed aircraft. Twenty-six different flight conditions were flown to cover the range of speeds, rpm, altitudes, and flap positions encountered by an advanced turboprop general aviation aircraft. Preliminary analysis of the flight test data indicate a strong three-dimensionality to the perturbed flow at the 75 and 90 percent radii due to pylon wake encounter. Time-history of the pressure transducer waveforms recorded for 700 revolutions exhibit a one-per-cycle wave oscillation on the wake signature. No explanation is found for this behavior yet.

Farokhi, S.↗

Pulsed response of a TWT

The consequence of frequency domain multiple access channelization in a satellite communications system is that the ground- and space-based components often are required to operate in a linear region to prevent the generation of distortion signals. Components of a time division multiple access (TDMA) satellite system, such as a traveling-wave tube (TWT), can operate in the highest output power state because the channelization technique is relatively insensitive to the distortions resulting from saturated operation. A 30 GHz TWT was tested to determine the suitability of such a device in a TDMA system. Testing was focused on the ability of the TWT's output signal to rise up to full power at the leading edge of TDMA bursts, simulated by a pulse train. A peak power meter was used to display and measure the pulsed signal waveform. Measurements on the TWT output pulse rise time indicate that the TWT lengthened the rise time by 10 to 20 ns. Imposing modulator turn on timing that precedes the data burst by the TWT rise time is a logical approach to coordination of the two subsystem specification.

May, Brian D.↗

Electromagnetic Chirps from Neutron Star-Black Hole Mergers

We calculate the electromagnetic signal of a gamma-ray flare coming from the surface of a neutron star shortly before merger with a black hole companion. Using a new version of the Monte Carlo radiation transport code Pandurata that incorporates dynamic spacetimes, we integrate photon geodesics from the neutron star surface until they reach a distant observer or are captured by the black hole. The gamma-ray light curve is modulated by a number of relativistic effects, including Doppler beaming and gravitational lensing. Because the photons originate from the inspiraling neutron star, the light curve closely resembles the corresponding gravitational waveform: a chirp signal characterized by a steadily increasing frequency and amplitude. We propose to search for these electromagnetic chirps using matched filtering algorithms similar to those used in LIGO data analysis.

gamma-ray burst↗

Frequency–wavenumber spectral analysis of spatio-temporal flows

We propose a fully spatio-temporal approach for identifying spatially varying modes of oscillation in fluid dynamics simulation output by means of multitaper frequency–wavenumber spectral analysis. One-dimensional spectrum estimation has proven to be a valuable tool in the analysis of turbulence data applied spatially to determine the rate of energy transport between spatial scales, or temporally to determine frequencies of oscillatory flows. It also allows for the quantitative comparison of flow characteristics between two scenarios using a standard basis. It has the limitation, however, that it neglects coupling between spatial and temporal structures. Two-dimensional frequency–wavenumber spectral analysis allows one to decompose waveforms into standing or travelling variety. The extended higher-dimensional multitaper method proposed here is shown to have improved statistical properties over conventional non-parametric spectral estimators, and is accompanied by confidence intervals which estimate their uncertainty. Multitaper frequency–wavenumber analysis is applied to a canonical benchmark problem, namely, a direct numerical simulation of von Kármán vortex shedding off a square wall-mounted cylinder with two inflow scenarios with matching momentum-thickness Reynolds numbers $Re_{\unicode[STIX]{x1D703}}\approx 1000$ at the obstacle. Frequency–wavenumber analysis of a two-dimensional section of these data reveals that although both the laminar and turbulent inflow scenarios show a turbulent $-5/3$ cascade in wavenumber ( $\unicode[STIX]{x1D708}$ ) and frequency ( $f$ ), the flow characteristics differ in that there is a significantly more prominent discrete harmonic oscillation near $(f,\unicode[STIX]{x1D708})=(0.2,0.21)$ in wavenumber and frequency in the laminar inflow scenario than the turbulent scenario. This frequency–wavenumber pair corresponds to a travelling wave with velocity near one near the centre path of the vortex street.

Geoga, Christopher J. (ORCID:0000000250604799)↗