Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “WING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 991 records · Page 55

Conical Euler simulation and active suppression of delta wing rocking motion

A conical Euler code was developed to study unsteady vortex-dominated flows about rolling highly-swept delta wings, undergoing either forced or free-to-roll motions including active roll suppression. The flow solver of the code involves a multistage Runge-Kutta time-stepping scheme which uses a finite volume spatial discretization of the Euler equations on an unstructured grid of triangles. The code allows for the additional analysis of the free-to-roll case, by including the rigid-body equation of motion for its simultaneous time integration with the governing flow equations. Results are presented for a 75 deg swept sharp leading edge delta wing at a freestream Mach number of 1.2 and at alpha equal to 10 and 30 deg angle of attack. A forced harmonic analysis indicates that the rolling moment coefficient provides: (1) a positive damping at the lower angle of attack equal to 10 deg, which is verified in a free-to-roll calculation; (2) a negative damping at the higher angle of attack equal to 30 deg at the small roll amplitudes. A free-to-roll calculation for the latter case produces an initially divergent response, but as the amplitude of motion grows with time, the response transitions to a wing-rock type of limit cycle oscillation. The wing rocking motion may be actively suppressed, however, through the use of a rate-feedback control law and antisymmetrically deflected leading edge flaps. The descriptions of the conical Euler flow solver and the free-to-roll analysis are presented. Results are also presented which give insight into the flow physics associated with unsteady vortical flows about forced and free-to-roll delta wings, including the active roll suppression of this wing-rock phenomenon.

Lee, Elizabeth M.↗

Numerical investigation of the flow over a double delta wing at high incidence

The vortical flowfield over a double-delta wing configuration, consisting of a sharp leading edge 76 deg sweep strake and a 40 deg sweep wing section is investigated. The governing equations are solved numerically with a partially upwind, finite-difference, factorized algorithm. The leeward side vortex system resulting from the strake and wing vortices is investigated for subsonic, high-Reynolds-number flow at various angles of incidence. At low angles of attack the strake and wing vortices remain separate over the wing section, while for flows at higher angles of attack the two vortices merge and vortex breakdown develops. Vortex breakdown appears initially at the trailing edge region of the wing section. As the angle of attack increases bursting occurs further upstream closer to the strake section. The effect of numerical grid density is investigated, and the solutions are compared with available experimental data.

Ekaterinaris, John A.↗

Static aeroelastic analysis of a three-dimensional oblique wing

A capability to perform static aeroelastic analyses of an oblique wing at arbitrary skew positions was developed based on the framework of the MSC/NASTRAN static aeroelastic analysis. By means of DMAP alterations, a portion of the subsonic static aeroelastic analysis scheme was modified to insert an aerodynamic influence coefficient matrix created externally by the NASA-Ames aerodynamic panel codes. The modified scheme can cover the subsonic as well as the supersonic range for both symmetric and asymmetric configurations. Static aeroelastic responses of the oblique wing are studied at two skew angles and, in particular, the capability to calculate 3D camber effects on the aerodynamic properties of the wing is investigated. Various aerodynamic coefficients of the rigid oblique wing are computed for two Mach numbers, 0.7 and 1.4, and the angle of attack is varied from -5 through 15 deg. Also, the wing flexibility effects on the aerodynamic coefficients and the displacement are examined at a Mach number of 0.7 for a 45-deg swept wing.

Lee, I.↗

NACA 0015 wing pressure and trailing vortex measurements

A NACA 0015 semispan wing was placed in a low-speed wind tunnel, and measurements were made of the pressure on the upper and lower surface of the wing and of velocity across the vortex trailing downstream from the tip of the wing. Pressure data were obtained for both 2-D and 3-D configurations. These data feature a detailed comparison between wing tips with square and round lateral edges. A two-component laser velocimeter was used to measure velocity profiles across the vortex at numerous stations behind the wing and for various combinations of conditions. These conditions include three aspect ratios, three chord lengths, a square- and a round lateral-tip, presence or absence of a boundary-layer trip, and three image plane positions located opposite the wing tip. Both pressure and velocity measurements were made for the angles of attack 4 deg less than or equal to alpha less than or equal to 12 deg and for Reynolds numbers 1 x 10(exp 6) less than or equal to Re less than or equal to 3 x 10(exp 6).

Mcalister, K. W.↗

Experimental study of an independently deflected wingtip mounted on a semispan wing

The results of a subsonic wind tunnel test of a semispan wing with an independently deflected tip surface are presented and analyzed. The tip surface was deflected about the quarter chord of the rectangular wing and accounted for 17 percent of the wing semispan. The test was conducted to measure the loads on the tip surface and to investigate the nature of aerodynamic interference effects between the wing and the deflected tip. Results are presented for two swept tip surfaces of similar planform but different airfoil distributions. The report contains plots of tip lift, drag, and pitching moment for various Reynolds numbers and tip deflection angles with respect to the inboard wing. Oil flow visualization photographs for a typical Reynolds number are also included. Important aerodynamic parameters such as lift and pitching moment slopes and tip aerodynamic center location are tabulated. A discussion is presented on the relationship between tip experimental data acquired in a steady flow and the prediction of unsteady tip motion at fixed wing angles of attack.

Martin, D. M.↗

A mathematical model of a tilt-wing aircraft for piloted simulation

A mathematical model of a tilt-wing aircraft that was used in a piloted, six-degree-of-freedom flight simulation application is described. Two types of control systems developed for the math model are discussed: a conventional, programmed-flap wing-tilt control system and a geared-flap wing-tilt control system. The primary objective was to develop the capability to study tilt-wing aircraft. Experienced Tilt-wing pilots subjectively evaluated the model using programmed-flap control to assess the quality of the simulation. The math model was then applied to study geared-flap control to investigate the possibility of eliminating the need for auxilary pitch-control devices (such as the horizontal tail rotor or tail jet used in earlier tilt-wing designs). This investigation was performed in the moving-base simulation environment, and the vehicle responses with programmed-flap and geared-flap control were compared. The results of the evaluation of the math model are discussed.

Totah, Joseph J.↗

Nonlinear aerodynamics and the design of wing tips

This report describes results of research conducted from April 1991 through March 1992. The general objective was to improve an existing wing optimization method, and apply the method to specific problems of interest. The method, while a valuable tool for wing tip design studies, can be applied to more general problems, and has been applied to some of these other problems during its development. Specific goals that were accomplished are listed and explained in more detail in the report. First, improvements were made to the portability and control flow of the existing code. The major iteration loop dealing with structural design was sped up and an alternate approach, using the optimizer to do structural sizing, was studied. Second, analysis methods were improved in the areas of structural and high lift modeling. The structural method was revised to give total wing weight and verified against data for particular commercial aircraft. The high lift analysis was improved to provide reasonable estimates of C(sub L max) in the flaps down condition. These improvements enabled making wing area a design variable, where it had been a fixed variable in the original method. Third, the method was applied to the design of wings for a Learjet. Rough studies were done to determine the effects of laminar flow design on wing shape. Finally, studies on wingtip shape were begun.

Kroo, Ilan↗

Analysis of iced wings

A method for computing ice shapes along the leading edge of a wing and a method for predicting its aerodynamic performance degradation due to icing is described. Ice shapes are computed using an extension of the LEWICE code which was developed for airfoils. The aerodynamic properties of the iced wing are determined with an interactive scheme in which the solutions of the inviscid flow equations are obtained from a panel method and the solutions of the viscous flow equations are obtained from an inverse three-dimensional finite-difference boundary-layer method. A new interaction law is used to couple the inviscid and viscous flow solutions. The application of the LEWICE wing code to the calculation of ice shapes on a MS-317 swept wing shows good agreement with measurements. The interactive boundary-layer method is applied to a tapered ice wing in order to study the effect of icing on the aerodynamic properties of the wing at several angles of attack.

Cebeci, T.↗

Analysis of iced wings

A method for computing ice shapes along the leading edge of a wing and a method for predicting its aerodynamic performance degradation due to icing is described. Ice shapes are computed using an extension of the LEWICE code which was developed for airfoils. The aerodynamic properties of the iced wing are determined with an interactive scheme in which the solutions of the inviscid flow equations are obtained from a panel method and the solutions of the viscous flow equations are obtained from an inverse three-dimensional finite-difference boundary-layer method. A new interaction law is used to couple the inviscid and viscous flow solutions. The application of the LEWICE wing code to the calculation of ice shapes on a MS-317 swept wing show good agreement with measurements. The interactive boundary layer method is applied to a tapered iced wing in order to study the effect of icing on the aerodynamic properties of the wing at several angles of attack.

Cebeci, Tuncer↗

Computation of vortex wake flows and control of their effects on trailing wings

The near-vortex-wake flow of a large aspect-ratio rectangular wing is accurately computed by using the thin-layer and full Navier-Stokes (NS) equations. The chordwise section of the wing is a NACA-0012 airfoil and its tip is round. The computations have been carried out on a fine C-O grid using an implicit, upwind, flux-difference splitting, finite-volume scheme. The thin-layer NS results have been obtained with and without flux limiters, and the full NS results have been obtained without flux limiters. Flow transition from laminar to turbulent is mimicked by turning-on the Baldwin-Lomax algebraic model at an experimentally prescribed chord-station location of 0.05. Comparison of computed results and experimental data shows that the full NS results give the best resolution of the near-vortex-wake flow. Next, the strength of the wing-tip vortex has been reduced substantially without reducing the lift coefficient by using flow-injection from a slot along a portion of the wing tip. The flow injection is directed in the wing plane at 45 deg with the wing-tip chord.

Wong, Tin-Chee↗

Investigation at low speeds of the effect of aspect ratio and sweep on rolling stability derivatives of untapered wings

A low scale wind tunnel investigation was conducted in rolling flow to determine the effects of aspect ratio and sweep (when varied independently) on the rolling stability derivatives for a series of untapered wings. Test results indicate that when the aspect ratio was held constant, an increase in the sweepback angle caused a significant reduction in the damping in roll at low lift coefficients for only the higher aspect ratios that were tested. This result was in agreement with available swept wing theory which indicated no effect of sweep for aspect ratios near zero. The result of the linear theory that the damping in roll is independent of lift coefficient and that the yawing moment and lateral force due to rolling are directly proportional to the lift coefficient was found to be valid for only a very limited lift coefficient range when the wings were highly swept. For such wings, the damping was found to increase in magnitude and the yawing moment due to rolling, to change from negative to positive at moderate lift coefficients. The effect of wing tip suction, not acounted for by present theory, was found to be very important with regard to the yawing moment due to rolling, particularly for low aspect ratio swept wings. An empirical means of correcting present theory for the effect of tip suction is suggested.

Goodman, Alex↗

Flight test results from a supercritical mission adaptive wing with smooth variable camber

The mission adaptive wing (MAW) consisted of leading- and trailing-edge variable-camber surfaces that could be deflected in flight to provide a near-ideal wing camber shape for any flight condition. These surfaces featured smooth, flexible upper surfaces and fully enclosed lower surfaces, distinguishing them from conventional flaps that have discontinuous surfaces and exposed or semiexposed mechanisms. Camber shape was controlled by either a manual or automatic flight control system. The wing and aircraft were extensively instrumented to evaluate the local flow characteristics and the total aircraft performance. This paper discusses the interrelationships between the wing pressure, buffet, boundary-layer and flight deflection measurement system analyses and describes the flight maneuvers used to obtain the data. The results are for a wing sweep of 26 deg, a Mach number of 0.85, leading and trailing-edge cambers (delta(sub LE/TE)) of 0/2 and 5/10, and angles of attack from 3.0 deg to 14.0 deg. For the well-behaved flow of the delta(sub LE/TE) = 0/2 camber, a typical cruise camber shape, the local and global data are in good agreement with respect to the flow properties of the wing. For the delta(sub LE/TE) = 5/10 camber, a maneuvering camber shape, the local and global data have similar trends and conclusions, but not the clear-cut agreement observed for cruise camber.

Powers, Sheryll Goecke↗

Navier-Stokes calculation of transonic flow past the NTF 65-deg delta wing

Viscous flow past a wind tunnel model of a 65-degree swept angle Delta wing at transonic speeds is being studied. The model was tested in the 8-foot cryogenic transonic wind tunnel at the National Transonic Facility. Aerodynamic forces and wing surface pressure data were obtained at various angles of attack, Mach numbers, and Reynold's numbers for four different leading edges of the wing. The objectives of the present investigation are: (1) to perform numerical modeling of the flow around the wing; (2) to validate the experimental data with a Navier-Stokes computational fluid dynamics code and vice versa; (3) to investigate the effects of the sting mount of the wing; (4) to evaluate the effects of leading edge radius on the flow; and (5) to explain the Reynold's number effect as indicated by the test data. Several computer programs were developed to define the surfaces of the wing, the four leading edges, and the sting mount. Based on these geometric databases, the surface grids of a single-block computational domain was generated interactively on the IRIS workstation using the GRIDGEN2D module of GRIDGEN. To refine the grids and to avoid excessive loss of grid points due to collapsed edges, a 9-block computational domain containing approximately 750,000 grid points was developed with the GRIDBLOCK module to replace the single-block grid.

Wu, Chivey↗

Construction, wind tunnel testing and data analysis for a 1/5 scale ultra-light wing model

This report documents the construction, wind tunnel testing, and data analysis of a 1/5 scale ultra-light wing section. Wind tunnel testing provided accurate and meaningful lift, drag, and pitching moment data. This data was processed and graphically presented as follows: C(sub L) vs. gamma; C(sub D) vs. gamma; C(sub M) vs. gamma; and C(sub L) vs. C(sub D). The wing fabric flexure was found to be significant and its possible effects on aerodynamic data was discussed. The fabric flexure is directly related to wing angle of attack and airspeed. Different wing section shapes created by fabric flexure are presented with explanations of the types of pressures that act upon the wing surface. This report provides conclusive aerodynamic data for ultra-light wings.

James, Michael D.↗

Flight Test Results From a Supercritical Mission Adaptive Wing With Smooth Variable Camber

The mission adaptive wing (MAW) consisted of leading- and trailing-edge variable-camber surfaces that could be deflected in flight to provide a near-ideal wing camber shape for any flight condition. These surfaces featured smooth, flexible upper surfaces and fully enclosed lower surfaces, distinguishing them from conventional flaps that have discontinuous surfaces and exposed or semiexposed mechanisms. Camber shape was controlled by either a manual or automatic flight control system. The wing and aircraft were extensively instrumented to evaluate the local flow characteristics and the total aircraft performance. This paper discusses the interrelationships between the wing pressure, buffet, boundary-layer and flight deflection measurement system analyses and describes the flight maneuvers used to obtain the data. The results are for a wing sweep of 26°, a Mach number of 0.85, leading and trailing-edge cambers ( δ LE/TE ) of 0/2 and 5/10, and angles of attack from 3.0° to 14.0°. For the well-behaved flow of the δ LE/TE = 0/2 camber, a typical cruise camber shape, the local and global data are in good agreement with respect to the flow properties of the wing. For the δ LE/TE = 5/10 camber, a maneuvering camber shape, the local and global data have similar trends and conclusions, but not the clear-cut agreement observed for cruise camber.

Flight Testing↗

Shock-dependent, thrust wings for supersonic flow

A new wing concept which lowers the inviscid drag of a wing in supersonic flow is described. The thrust-wing concept uses a secondary shock that occurs to the rear of the maximum thickness location to produce a significant aerodynamic thrust force from the rearward portion of the wing, thus reducing the inviscid drag. The evaluation of the thrust-wing concept is conducted on a delta-wing planform of differing sweep angles and thicknesses at Mach 1.60 over a wide range of lifting conditions.

Pittman, James L.↗

Integrated Aerodynamic and Control System Design of Oblique Wing Aircraft

An efficient high speed aircraft design must achieve a high lift to drag ratio at transonic and supersonic speeds. In 1952 Dr. R. T. Jones proved that for any flight Mach number minimum drag at a fixed lift is achieved by an elliptic wing planform with an appropriate oblique sweep angle. Since then, wind tunnel tests and numerical flow models have confirmed that the compressibility drag of oblique wing aircraft is lower than similar symmetrical sweep designs. At oblique sweep angles above thirty degrees the highly asymmetric planform gives rise to aerodynamic and inertia couplings which affect stability and degrade the aircraft's handling qualities. In the case of the NASA-Rockwell Oblique Wing Research Aircraft, attempts to improve the handling qualities by implementing a stability augmentation system have produced unsatisfactory results because of an inherent lack of controllability in the proposed design. The present work focuses on improving the handling qualities of oblique wing aircraft by including aerodynamic configuration parameters as variables in the control system synthesis to provide additional degrees of freedom with which to further decouple the aircraft's response. Handling qualities are measured using a quadratic cost function identical to that considered in optimal control problems, but the controller architecture is not restricted to full state feedback. An optimization procedure is used to simultaneously solve for the aircraft configuration and control gains which maximize a handling qualities measure, while meeting imposed constraints on trim. In some designs wing flexibility is also modeled and reduced order controllers are implemented. Oblique wing aircraft synthesized by this integrated design method show significant improvement in handling qualities when compared to the originally proposed closed loop aircraft. The integrated design synthesis method is then extended to show how handling qualities may be traded for other types of mission performance (drag, weight, etc.). Examples are presented which show how performance can be maximized while maintaining a desired level of handling quality.

Morris, Stephen James↗

The Distribution of Loads Between the Wings of a Biplane Having Decalage

It is known that in a biplane the load is not distributed equally between the wings. The presence of one wing will affect the lift characteristics of the other wings. A designer must know the total load that each wing carries in order that he may design an adequate structure. The purpose here is to determine the distribution of loads between the wings of a biplane at various angles of decalage, when the gap/chord ratio is one, and there is no stagger. The effective lift of each wing was first investigated, using the vortex theory, and later by wind tunnel experiments. The results are given in tabular form.

Mock, Richard M↗