Evaluation of breaking performance of a light, twin-engine airplane on grooved and ungrooved pavements
Evaluation of braking performance of light, twin engine airplane on grooved and ungrooved runway surfaces
SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Evaluation of braking performance of light, twin engine airplane on grooved and ungrooved runway surfaces
The test was a conventional stability and control test except for two aspects. One was the very high angles of attack at which the delta wing configurations were tested (up to 60 degrees) at Mach numbers of 3 and 4.96. The other was the installation of the orbiter and twin boosters in a manner that caused the support system to induce normal forces and side forces on the aft portion of the boosters at all Mach numbers; i.e., the support and the booster bodies were close together, side by side.
Representative state-of-the-art analytical procedures and design data for predicting the longitudinal static and dynamic stability and control characteristics of light, propeller-driven airplanes are presented. Procedures for predicting drag characteristics are also included. The procedures are applied to a twin-engine, propeller-driven airplane in the clean configuration from zero lift to stall conditions. The calculated characteristics are compared with wind-tunnel and flight data. Included in the comparisons are level-flight trim characteristics, period and damping of the short-period oscillatory mode, and windup-turn characteristics. All calculations are documented.
An investigation was conducted in the Langley full-scale tunnel to determine the dynamic stability derivatives in pitch, roll, and yaw over an angle-of-attack range of -5 deg to 90 deg for a variable-sweep fighter configuration with twin vertical tails. The study consisted of forced-oscillation tests of a 1/10-scale model of the airplane at a Reynolds number of 0.4 million based on the reference wing mean aerodynamic chord. Tests were conducted for wing sweep angles of 22 deg, 35 deg, 50 deg, and 68 deg, and the effects of the vertical and horizontal tails, wing leading-edge slats, nose-mounted canards, and frequency of the oscillation were also evaluated.
An investigation has been conducted with a free-flying radio-controlled 0.15-scale model of a twin-jet swept-wing fighter airplane to determine the tendency of this design to enter spins and to evaluate the nature of the spin obtained from post-stall motions. The test results indicate that it may be difficult to obtain a developed spin on the airplane, particularly the flat-type spin. Two types of erect developed spins will be possible; one will be flat and fast rotating from which recovery may not be obtained and the other will be steeper and oscillatory from which recoveries will be satisfactory. Controls will be effective for satisfactory termination of the post-stall gyrations obtained. The recommended recovery technique from both post-stall gyrations and developed spins will be movement of the rudder to oppose the yawing rotation and simultaneous movement of the ailerons to with the rotation (stick right when turning to the right). When recovery is imminent, the stick should be moved longitudinally to neutral. It is recommended that the spin not be allowed to develop fully on this airplane. The developed-spin results obtained in the investigation were in good agreement with spin-tunnel results.
Twin-jet afterbody models were investigated by using two balances to measure the thrust-minus-total drag and the afterbody drag, separately, at static conditions and at Mach numbers up to 2.2 for an angle of attack of 0 deg. Hinged-flap convergent-divergent nozzles were tested at subsonic-cruise- and maximum-afterburning-power settings with a high-pressure air system used to provide jet-total-pressure ratios up to 20. Two nozzle lateral spacings were studied, using afterbodies with similar interfairing shapes but with different longitudinal cross-sectional area distributions. Alternate, blunter, interfairings with different shapes for the two spacings, which produced afterbodies having identical cross-sectional area progressions corresponding to an axisymmetric minimum wave-drag configuration, were also tested. The results indicate that the wide-spaced configurations improved the flow field around the nozzles, thereby reducing drag on the cruise nozzles; however, the increased surface and projected cross-sectional areas caused an increase in afterbody drag. Except for a slight advantage with cruise nozzles at subsonic speeds, the wide-spaced configurations had the higher total drag at all other test conditions.
Twin-jet afterbody models were investigated by using two balances to measure separately the thrust minus total drag and the afterbody drag at Mach numbers of 0.0 and 0.50 to 2.20 for a constant angle of attack of 0. Translating shroud cone plug nozzles were tested at dry and maximum afterburning power settings with a high-pressure air system used to provide jet total-pressure ratios up to 20.0. Two nozzle lateral spacings were studied by using afterbodies with several interfairing shapes. The close- and wide-spaced afterbodies had identical cross-sectional area distributions when similar interfairings were installed on each. Nozzle cant angles of -5, 0, and 5 degrees were investigated. The results show that the highest overall performance was generally obtained with the close-spaced afterbody, basic interfairings (no base), and uncanted nozzles.
An investigation has been conducted at Mach numbers ranging from 0.06 to 0.94 to determine the effects of various combinations of leading-edge slat devices on the static aerodynamic characteristics of a twin-jet swept-wing fighter model. The study also included a determination of the effects of wing leading-edge droop, trailing-edge chord-extensions, wing fences, and wing-planform and camber modifications. The angle-of-attack range generally extended from about minus 2 deg to 24 deg and the sideslip angles ranged from about minus 6 deg to 13 deg.
Wind tunnel tests of a full-scale model of a light twin engine aircraft were conducted. The angle of attack was varied from minus 4 degrees to plus 20 degrees. The sideslip range was plus or minus 8 degrees. Thrust coefficients were 0, 0.20, and 0.44. Tests were made with various nacelle configurations, modes of propeller rotation, orientation of the thrust axis, and airfoil section at Reynolds numbers of 2.96 times one million amd 2.05 times one million.
Experimental results of terminal shock and restart control system tests of a two-dimensional, twin-duct mixed compression inlet are presented. High-response (110-Hz bandwidth) overboard bypass doors were used, both as the variable to control shock position and as the means of disturbing the inlet airflow. An inherent instability in inlet shock position resulted in noisy feedback signals and thus restricted the terminal shock position control performance that was achieved. Proportional-plus-integral type controllers using either throat exit static pressure or shock position sensor feedback gave adequate low-frequency control. The inlet restart control system kept the terminal shock control loop closed throughout the unstart-restart transient. The capability to restart the inlet was non limited by the inlet instability.
Twin-jet afterbody models were investigated by using two balances to measure separately the thrust minus total axial force and the afterbody drag at Mach numbers from 0 to 1.3. Angle of attack was varied from minus 2 deg to 8.5 deg. Translating shroud cone plug nozzles were tested at dry-power and maximum-afterburning-power settings with a high-pressure air system used to provide jet total-pressure ratios up to 9.0. Two nozzle lateral spacings were studied by using afterbodies with several interfairing shapes. The close- and wide-spaced afterbodies had identical cross-sectional area distributions when similar interfairings were installed on each. The results show that the highest overall performance was obtained with the close-spaced afterbody and basic interfairings. Increasing angle of attack decreased performance for all configurations and conditions investigated.
A wind-tunnel investigation has been conducted to determine the effects of slot spoilers on the longitudinal and lateral aerodynamic characteristics of a full-scale mockup of a light twin-engine airplane. The slots were located along the leading edge of the flaps and were used to modulate the flap-induced lift as a possible means of achieving direct lift control. The data showed that the slots were effective in spoiling up to 61 percent of the flap-induced lift, but that an adverse pitching-moment change (nose up) accompanied opening the slots. Opening the slots was found to decrease slightly the downwash angle at the tail and to increase slightly the longitudinal stability of the model.
The investigation was made on a 1/18-scale model of a twin-engine light airplane. Static longitudinal, lateral, and directional characteristics were obtained at 0 deg and plus or minus 5 deg sideslip at a Mach number of about 0.2. The angle of attack varied from about 20 deg at a Reynolds number of 0.39 times one million to 13 deg at a Reynolds number of 3.7 times one million, based on the reference chord. The effect of fixed transition, vertical and horizontal tails, and nacelle fillets was studied.
An investigation has been conducted by means of wind-tunnel tests of a full-scale mockup of a light twin-engine airplane configuration to determine the effects of outboard partial-span slots and of auxiliary airfoils ahead of the leading edge of the wing in improving aerodynamic characteristics at high angles of attack. Both of the stall-control devices gave considerable improvement in high angle-of-attack characteristics with the auxiliary airfoil giving the more favorable results, but neither device performed as well as might have been expected.
A wind-tunnel investigation has been conducted to determine the exhaust-nozzle aerodynamic and propulsive characteristics for a twin-jet variable-wing-sweep fighter airplane model. The powered model was tested in the Langley 16-foot transonic tunnel and in the Langley 4-foot supersonic pressure tunnel at Mach numbers to 2.2 and at angles of attack from about minus 2 to 6 deg. Compressed air was used to simulate the nozzle exhaust flow at values of jet total-pressure ratio from approximately 1 (jet off) to about 21. Effects of configuration variables such as speed-brake deflection, store installation, and boundary-layer thickness on the the nozzle characteristics were also investigated.
An investigation was conducted to determine the low-speed yawing stability derivatives of a twin-jet fighter airplane model at high angles of attack. Tests were performed in a low-speed tunnel utilizing variable-curvature walls to simulate pure yawing motion. The results of the study showed that at angles of attack below the stall the yawing derivatives were essentially independent of the yawing velocity and sideslip angle. However, at angles of attack above the stall some nonlinear variations were present and the derivatives were strongly dependent upon sideslip angle. The results also showed that the rolling moment due to yawing was primarily due to the wing-fuselage combination, and that at angles of attack below the stall both the vertical and horizontal tails produced significant contributions to the damping in yaw. Additionally, the tests showed that the use of the forced-oscillation data to represent the yawing stability derivatives is questionable, at high angles of attack, due to large effects arising from the acceleration in sideslip derivatives.
A 1/10-scale powered model of a twin-engine attack airplane was investigated in the Langley high-speed 7- by 10-foot tunnel. The study was made at several Mach numbers between 0.225 and 0.75 which correspond to Reynolds numbers, based on the mean aerodynamic chord, of 1.35 million and 3.34 million. Unheated compressed air was used for jet simulation in the nonmetric engine nacelles which were located ahead of and above the horizontal stabilizer.
An investigation was conducted in a full scale wind tunnel to determine the performance and aerodynamic characteristics of a twin engine, straight wing, upper surface blown jet flap configuration. The model had two simulated high bypass ratio turbofan engines with rectangular nozzles exhausting onto the upper surface of the wing at the 35 percent chord station. The model was tested with an aspect ratio 8.2 wing and with the wingtips removed to give an aspect ratio of 6.0.