Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “TIP SPEED”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 991 records · Page 55
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Aerodynamic and mechanical design of an 8:1 pressure ratio centrifugal compressor

A high-pressure-ratio, low-mass-flow centrifugal compressor stage was designed, fabricated, and tested. The design followed specifications that the stage be representative of state-of-the-art performance and that the stage is to be used as a workhorse compressor for planned experiments using laser Doppler velocimeter equipment. The final design is a 75,000-RPM, 19-blade impeller with an axial inducer and 30 degrees of backward leaning at the impeller tip. The compressor design was tested for two- and/or quasi-three-dimensional aerodynamic and stress characteristics. Critical speed analyses were performed for the high speed rotating impeller assembly. An optimally matched, 17-channel vane island diffuser was also designed and built.

Osborne, C.↗
NASA NTRS1982

Vortex lift augmentation by suction on a 60 deg swept Gothic wing

An experimental investigation was conducted in the Langley high-speed 7- by 10-foot wind tunnel to determine the aerodynamic performance of suction applied near the wing tips above the trailing edge of a 60 deg swept Gothic wing. Moveable suction inlets were symmetrically mounted in the proximity of the trailing edge, and the amount of suction was varied to maximize wing lift. Tests were conducted at Mach 0.15, 0.30, and 0.45, and the angle of attack was varied from -4 to 50 deg. The suction augmentation increases the lift coefficient over the entire range of angle of attack. The lift improvement exceeds the unaugmented wing lift by over 20%. Moreover, the augmented lift exceeds the lift predicted by vortex lattice theory to 30 deg angle of attack. Suction augmentation is postulated to strengthen the vortex system by increasing its velocity and making it more concentrated. This causes the vortex breakdown to be delayed to a higher angle of attack

Taylor, A. H.↗
NASA NTRS2010

Minnowbrook VI: 2009 Workshop on Flow Physics and Control for Internal and External Aerodynamics

Topics covered include: Flow Physics and control for Internal and External Aerodynamics (not in TOC...starts on pg13); Breaking CFD Bottlenecks in Gas-Turbine Flow-Path Design; Streamwise Vortices on the Convex Surfaces of Circular Cylinders and Turbomachinery Blading; DNS and Embedded DNS as Tools for Investigating Unsteady Heat Transfer Phenomena in Turbines; Cavitation, Flow Structure and Turbulence in the Tip Region of a Rotor Blade; Development and Application of Plasma Actuators for Active Control of High-Speed and High Reynolds Number Flows; Active Flow Control of Lifting Surface With Flap-Current Activities and Future Directions; Closed-Loop Control of Vortex Formation in Separated Flows; Global Instability on Laminar Separation Bubbles-Revisited; Very Large-Scale Motions in Smooth and Rough Wall Boundary Layers; Instability of a Supersonic Boundary-Layer With Localized Roughness; Active Control of Open Cavities; Amplitude Scaling of Active Separation Control; U.S. Air Force Research Laboratory's Need for Flow Physics and Control With Applications Involving Aero-Optics and Weapon Bay Cavities; Some Issues Related to Integrating Active Flow Control With Flight Control; Active Flow Control Strategies Using Surface Pressure Measurements; Reduction of Unsteady Forcing in a Vaned, Contra-Rotating Transonic Turbine Configuration; Active Flow Control Stator With Coanda Surface; Controlling Separation in Turbomachines; Flow Control on Low-Pressure Turbine Airfoils Using Vortex Generator Jets; Reduced Order Modeling Incompressible Flows; Study and Control of Flow Past Disk, and Circular and Rectangular Cylinders Aligned in the Flow; Periodic Forcing of a Turbulent Axisymmetric Wake; Control of Vortex Breakdown in Critical Swirl Regime Using Azimuthal Forcing; External and Turbomachinery Flow Control Working Group; Boundary Layers, Transitions and Separation; Efficiency Considerations in Low Pressure Turbines; Summary of Conference; and Final Plenary Session Transcript.

LaGraff, John E.↗
NASA NTRS2016

Experimental Study of Tip Vortex Flow from a Periodically Pitched Airfoil Section

An experimental investigation of tip vortex flow from a NACA0012 airfoil, pitched periodically at various frequencies, is conducted in a low-speed wind tunnel. Initially, data for stationary airfoil held fixed at various angles-of-attack are gathered. Flow visualization pictures as well as detailed cross-sectional properties areobtained at various streamwise locations using hot-wire anemometry. Data include mean velocity, streamwise vorticity as well as various turbulent stresses. Preliminary data are also acquired for periodically pitched airfoil. These results are briefly presented in this extended abstract.

wing aerodynamics↗
NASA NTRS1994

Measurements of Supersonic Wing Tip Vortices

An experimental survey of supersonic wing tip vortices has been conducted at Mach 2.5 using small performed 2.25 chords down-stream of a semi-span rectangular wing at angle of attack of 5 and 10 degrees. The main objective of the experiments was to determine the Mach number, flow angularity and total pressure distribution in the core region of supersonic wing tip vortices. A secondary aim was to demonstrate the feasibility of using cone probes calibrated with a numerical flow solver to measure flow characteristics at supersonic speeds. Results showed that the numerically generated calibration curves can be used for 4-hole cone probes, but were not sufficiently accurate for conventional 5-hole probes due to nose bluntness effects. Combination of 4-hole cone probe measurements with independent pitot pressure measurements indicated a significant Mach number and total pressure deficit in the core regions of supersonic wing tip vortices, combined with an asymmetric 'Burger like' swirl distribution.

Smart, Michael K.↗
DOE OSTI2023

New insights on wind turbine wakes from large‐eddy simulation: Wake contraction, dual nature, and temperature effects

Abstract Large‐eddy simulation (LES) has been adopted to study wind turbine wakes because it can capture fine‐scale details of turbulent wind flows and interactions with wind turbines. Here, we use the LES version of the Weather Research and Forecasting (WRF) model with an actuator disk model to gain insights on several wake effects that have been traditionally difficult to measure. The first finding is that the wake has a “dual nature,” meaning that the wind speed deficit behaves differently from the added turbulent kinetic energy (TKE) and the two are not co‐located in space. For example, the wind speed deficit peaks at hub height and reaches the ground within 8D (D is the rotor diameter), but added TKE peaks near the rotor tip and generally remains aloft. Second, temperature changes near the ground are driven by the added TKE in the rotor area and by atmospheric stability. The combination of these two factors determines the sign and intensity of the vertical heat flux divergence below the rotor, with convergence and warming associated with stable conditions and weak divergence and modest cooling with unstable conditions. Third, wakes do not expand indefinitely, as suggested by similarity theory applied to the wind speed deficit, but eventually stop expanding and actually contract, at different rates depending on atmospheric stability. The implication of these findings is that, in order to study wakes, it is not sufficient to focus on wind speed deficit alone, because TKE is also important and yet behaves differently from the wind speed deficit.

17 WIND ENERGY↗
NASA NTRS1984

Analytic investigation of helicopter rotor blade appended aeroelastic devices

Analytic evaluations of four different passive aeroelastic devices appended to helicopter rotor blades are presented. The devices consist of a passive tuned tab, a control coupled tab, an all-flying tip and a harmonic dilational airfoil tip. Each device was conceived for improving either aerodynamic performance or reducing vibratory control loads or hub shears. The evaluation was performed using a comprehensive rotor aeroelastic analysis (the G400PA code with appropriate modifications), together with data for a realistic helicopter rotor blade (the UH-60A Blackhawk), in high speed flight (90 m/s, 175 kts). The results of this study show that significant performance (L/(D sub e)) gains can be achieved with the all-flying free tip. Results from the harmonic dilational airfoil tip show the potential for moderate improvements in L/(D sub e). Finally, the results for the passive tuned tab and the control coupled tab, as configured for this study, show these devices to be impractical. Sections are included which describe the operation of each device, the required G400PA modifications, and the detailed results obtained for each device.

Bielawa, Richard L.↗
NASA NTRS1980

Full scale visualization of the wing tip vortices generated by a typical agricultural aircraft

The trajectories of the wing tip vortices of a typical agricultural aircraft were experimentally determined by flight test. A flow visualization method, similar to the vapor screen method used in wind tunnels, was used to obtain trajectory data for a range of flight speeds, airplane configurations, and wing loadings. Detailed measurements of the spanwise surface pressure distribution were made for all test points. Further, a powered 1/8 scale model of the aircraft was designed, built, and used to obtain tip vortex trajectory data under conditions similar to that of the full scale test. The effects of light wind on the vortices were demonstrated, and the interaction of the flap vortex and the tip vortex was clearly shown in photographs and plotted trajectory data.

Cross, E. J., Jr.↗
NASA NTRS1980

Full scale visualization of the wing tip vortices generated by a typical agricultural aircraft

The trajectories of the wing tip vortices of a typical agricultural aircraft were experimentally determined by flight test. A flow visualization method, similar to the vapor screen method used in wind tunnels, was used to obtain trajectory data for a range of flight speeds, airplane configurations, and wing loadings. Detailed measurements of the spanwise surface pressure distribution were made for all test points. Further, a powered 1/8 scale model of the aircraft was designed, built, and used to obtain tip vortex trajectory data under conditions similar to that of the full-scale test. The effects of light wind on the vortices were demonstrated, and the interaction of the flap vortex and the tip vortex was clearly shown in photographs and plotted trajectory data.

Cross, E. J., Jr.↗
NASA NTRS2005

TRMM Re-Entry Planning: Attitude Determination and Control During Thruster Modes

The Tropical Rainfall Measuring Mission (TRMM) spacecraft has been undergoing design for a controlled re-entry to Earth. During simulation of the re-entry plan, there was evidence of errors in the attitude determination algorithms during thruster modes. These errors affected the bum efficiency, and thus planning, during re-entry. During thruster modes, the spacecraft attitude is controlled off of integrated Gyro Error Angles that were designed to closely follow the nominal spacecraft pointing frame (Tip Frame). These angles, however, were not exactly mapped to the Tip Frame from the Body Frame. Additionally, in the initial formulation of the thruster mode attitude determination algorithms, several assumptions and approximations were made to conserve processor speed. These errors became noticeable and significant when simulating bums of much longer duration (-10 times) than had been produced in flight. A solution is proposed that uses attitude determination information from a propagated extended Kalman filter that already exists in the TRMM thruster modes. This attitude information is then used to rotate the Gyro Error Angles into the Tip Frame. An error analysis is presented that compares the two formulations. The new algorithm is tested using the TRMM High-Fidelity Simulator and verified with the TRMM Software Testing and Training Facility. Simulation results for both configurations are also presented.

DeWeese, Keith↗
NASA NTRS1991

Nonlinear Aerodynamics and the Design of Wing Tips

The analysis and design of wing tips for fixed wing and rotary wing aircraft still remains part art, part science. Although the design of airfoil sections and basic planform geometry is well developed, the tip regions require more detailed consideration. This is important because of the strong impact of wing tip flow on wing drag; although the tip region constitutes a small portion of the wing, its effect on the drag can be significant. The induced drag of a wing is, for a given lift and speed, inversely proportional to the square of the wing span. Concepts are proposed as a means of reducing drag. Modern computational methods provide a tool for studying these issues in greater detail. The purpose of the current research program is to improve the understanding of the fundamental issues involved in the design of wing tips and to develop the range of computational and experimental tools needed for further study of these ideas.

Kroo, Ilan↗
DOE OSTI2020

Combined visualisation of cavitation and vortical structures in a real-size optical diesel injector

A high-speed flow visualisation set-up comprising of combined diffuse backlight illumination (DBI) and schlieren imaging has been developed to illustrate the highly transient, two-phase flow arising in a real-size optical fuel injector. The different illumination nature of the two techniques, diffuse and parallel light respectively, allows for the capturing of refractive-index gradients due to the presence of both interfaces and density gradients within the orifice. Hence, the onset of cavitation and secondary-flow motion within the sac and injector hole can be concurrently visualised. Experiments were conducted utilising a diesel injector fitted with a single-hole transparent tip (ECN spray D) at injection pressures of 700–900 bar and ambient pressures in the range of 1–20 bar. High-speed DBI images obtained at 100,000 fps revealed that the orifice, due to its tapered layout, is mildly cavitating with relatively constant cavity sheets arising mainly in regions of manufacturing imperfections. Nevertheless, schlieren images obtained at the same frame rate demonstrated that a multitude of vortices with short lifetimes arise at different scales in the sac and nozzle regions during the entire duration of the injection cycle but the vortices do not necessarily result in phase change. The magnitude and exact location of coherent vortical structures have a measurable influence on the dynamics of the spray emerging downstream the injector outlet, leading to distinct differences in the variation of its cone angle depending on the injection and ambient pressures examined.

42 ENGINEERING↗
NASA NTRS1977

Operating characteristics of an inlet model tested with a 0.5m powered fan at high angles of attack

An inlet model designed for high angle of attack capability, coupled to a .508 m tip diameter turbofan simulator, was tested in the NASA-Lewis Research Center's 9-by 15-ft low speed wind tunnel. The test variables were: tunnel velocity, 0 to 75 m/s; inlet angle of attack, 0 to 120 deg; and fan face corrected airflow per unit area, 75 to 200 kg/s sqm. The inlet flow separation boundaries, the fan face total pressure recovery and distortion characteristics, and the fan blade vibratory stresses were determined. The recovery, distortion, and stress levels showed no abrupt changes at the onset of separation, but became gradually more unfavorable as the size and intensity of the separation increased as induced by increasingly severe operating conditions. Performance characteristics for a large scale model of the inlet were estimated from these test results.

Koncsek, J. L.↗
NASA NTRS1992

Exploratory investigation of a spanwise blowing concept for tip-stall control on cranked-arrow wings

A novel blowing concept aimed at controlling the tip-panel stall of 'cranked-arrow' type wings was experimentally investigated. A spanwise-directed jet sheet tangential to the upper surface, blown from a chordwise slot located at the crank, interacts obliquely with the external flow to generate a powerful and highly controllable vortex, substantially covering the tip panel. The incremental suction due to this jet vortex, coupled with its flow stabilization effect improves the tip-panel maximum lift and stall characteristics, leading to pitch-up alleviation and lateral control augmentation. Low-speed wind tunnel flow visualizations, pressure measurements and force/moment results are presented validating the flow-control concept and illustrating its potential on a generic crank-arrow wing model.

Rao, Dhanvada M.↗
NASA NTRS1993

A macro-micro robot for precise force applications

This paper describes an 8 degree-of-freedom macro-micro robot capable of performing tasks which require accurate force control. Applications such as polishing, finishing, grinding, deburring, and cleaning are a few examples of tasks which need this capability. Currently these tasks are either performed manually or with dedicated machinery because of the lack of a flexible and cost effective tool, such as a programmable force-controlled robot. The basic design and control of the macro-micro robot is described in this paper. A modular high-performance multiprocessor control system was designed to provide sufficient compute power for executing advanced control methods. An 8 degree of freedom macro-micro mechanism was constructed to enable accurate tip forces. Control algorithms based on the impedance control method were derived, coded, and load balanced for maximum execution speed on the multiprocessor system.

Marzwell, Neville I.↗
NASA NTRS1950

The effect of torsional flexibility on the rolling characteristics at supersonic speeds of tapered unswept wings

An analysis is presented of the effect of torsional flexibility on the rolling characteristics at supersonic speeds of tapered unswept wings with partial-span constant-percent-chord ailerons extending inboard from the wing tip. The geometric variables considered are aspect ratio, taper ratio, aileron span, and aileron chord. The shape of the wing-torsional-stiffness curve is assumed and the twisting moment is considered to result solely from the pressure distribution caused by aileron deflection, so that the necessity of using a successive-approximation method is avoided. Because of the complexity of the equations resulting from the analysis, numerical calculations from the equations are presented in a series of figures. A computational form is provided to be used in conjunction with these figures so that calculations can be made without reference to the analysis.

Tucker, Warren A↗
NASA NTRS1993

Design and control of a macro-micro robot for precise force applications

Creating a robot which can delicately interact with its environment has been the goal of much research. Primarily two difficulties have made this goal hard to attain. The execution of control strategies which enable precise force manipulations are difficult to implement in real time because such algorithms have been too computationally complex for available controllers. Also, a robot mechanism which can quickly and precisely execute a force command is difficult to design. Actuation joints must be sufficiently stiff, frictionless, and lightweight so that desired torques can be accurately applied. This paper describes a robotic system which is capable of delicate manipulations. A modular high-performance multiprocessor control system was designed to provide sufficient compute power for executing advanced control methods. An 8 degree of freedom macro-micro mechanism was constructed to enable accurate tip forces. Control algorithms based on the impedance control method were derived, coded, and load balanced for maximum execution speed on the multiprocessor system. Delicate force tasks such as polishing, finishing, cleaning, and deburring, are the target applications of the robot.

Wang, Yulun↗
NASA NTRS1993

Studies of blade-vortex interaction noise reduction by rotor blade modification

Blade-vortex interaction (BVI) noise is one of the most objectionable types of helicopter noise. This impulsive blade-slap noise can be particularly intense during low-speed landing approach and maneuvers. Over the years, a number of flight and model rotor tests have examined blade tip modification and other blade design changes to reduce this noise. Many times these tests have produced conflicting results. In the present paper, a number of these studies are reviewed in light of the current understanding of the BVI noise problem. Results from one study in particular are used to help establish the noise reduction potential and to shed light on the role of blade design. Current blade studies and some new concepts under development are also described.

Brooks, Thomas F.↗