Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Selection pressure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 991 records · Page 55
All sourcesNASA NTRSDOE OSTI
NASA NTRS2003

Solar Array in Simulated LEO Plasma Environment

Six different types of solar arrays have been tested in large vacuum chambers. The low earth orbit plasma environment was simulated in plasma vacuum chambers, where the parameters could be controlled precisely. Diagnostic equipment included spherical Langmuir probes, mass spectrometer, low-noise CCD camera with optical spectrometer, video camera, very sensitive current probe to measure arc current, and a voltage probe to register variations in a conductor potential. All data (except video) were obtained in digital form that allowed us to study the correlation between external parameters (plasma density, additional capacitance, bias voltage, etc) and arc characteristics (arc rate, arc current pulse width and amplitude, gas species partial pressures, and intensities of spectral lines). Arc inception voltages, arc rates, and current selections are measured for samples with different coverglass materials and thickness, interconnect designs, and cell sizes. It is shown that the array with wrapthrough interconnects have the highest arc threshold and the lowest current collection. Coverglass design with overhang results in decrease of current collection and increase of arc threshold. Doubling coverglass thickness cases the increase in arc inception voltage. Both arc inception voltage and current collection increase significantly with increasing a sample temperature to 80 C. Sustained discharges are initiated between adjacent cells with potential differences of 40 V for the sample with 300 micron coverglass thickness and 60 V for the sample with 150 micron coverglass thickness. Installation of cryogenic pump in large vacuum chamber provided the possibility of considerable outgassing of array surfaces which resulted in significant decrease of arc rate. Arc sites were determined by employing a video-camera, and it is shown that the most probable sites for arc inception are triple-junctions, even though some arcs were initiated in gaps between cells. It is also shown that the arc rate increases with increasing of ion collection current. The analysis of optical spectra (240-800 nm) reveals intensive narrow atomic lines (Ag, H) and wide molecular bands (OH, CH, SiH, SiN) that confirms a complicated mechanism of arc plasma generation. The results obtained seem to be important for the understanding of the arc inception mechanism, which is absolutely essential for progress toward the design of high-voltage solar array for space application.

Vayner, Boris↗
NASA NTRS1999

Customized Hermetic Feedthrough Developed to Isolate Fluids

A common problem occurs when refrigerant fluids wick inside the insulation of thermocouple wires through a compressor's casing feedthrough and then leak into the adjacent disconnect box outside the casing. Leaking fluids create an unfavorable situation inside the disconnect box and may contaminate the fluids. To address this problem, NASA Lewis Research Center s Manufacturing Engineering Division developed a customized hermetic feedthrough for a bank of Worthington compressors. In these compressors, bearing temperatures are measured by internal thermocouples embedded in bearings located inside the compressor casings. The thermocouple wires need to be routed outside the casing and read at another location. These wires are short and are terminated to a disconnect strip inside the casing. The bearings operate at about 170 F, but because the casing is filled with R12 refrigerant oil, the casing has a maximum temperature of about 100 F. The operating conditions of these compressors permit the use of an epoxy that is compatible with the R12 fluid. The desired finished product is a stainless steel tube that has been filled solid with epoxy after thermocouple wires bonded and sealed by epoxy have been inserted through its length. Shrink tubing extends from both ends of the tube. The process that was developed to isolate the thermocouple wires from the R12 fluid follows. For this application, use an 8-in.-long piece of 0.500-in. 304 stainless steel tube with six pairs of 24-gauge stranded, PTFE-insulated (polytetrafluoroethylene) type "T" thermocouple wires for each feedthrough. Use shrink tubing to strain relief the insulated wires at their exit from the stainless steel tube. Cut the wire to length and identify the location of the stainless steel tube sleeve with masking tape. Then, remove the outer insulation from a 2-in. section of wire that will be inside the tube, and carefully strip to bare wire a 1-in. section in the middle of the section with the outer insulation removed. For an effective seal, the epoxy must penetrate between the strands when stranded conductors are used. Make the seal with epoxy bond on the bare wire. The bare wire must be encapsulated with a thin layer of the epoxy that leaves only a very low profile. These encapsulated wires must cure before the assembly can be continued. Then, inspect the cured wires for complete encapsulation before going to the next step. Insert the wires in the stainless steel tube and orient them so that the epoxied stripped sections are staggered within the tube; then, apply shrink tubing to one end of the cleaned wires, positioning it inside the edge of the tube. The small gaps between the wires on the other end will be used to inject the epoxy into the tube. Let the epoxy cure inside the tube, free of any voids. Then, continue to fill the tube until the entire 8-in. length is nearly filled, allowing room for the other strain-relieving shrink tubing. Since this first design, the process has been adjusted to fit many needs and situations. Customized feedthroughs have been assembled from various wire types, wire gauges, and/or stainless steel tube passages. The fittings selected to mount these feedthroughs allow their use in other areas, such as pressure or vacuum systems.

Meredith, Roger D.↗
NASA NTRS2007

The Impact of Atmospheric InfraRed Sounder (AIRS) Profiles on Short-term Weather Forecasts

The Atmospheric Infrared Sounder (AIRS), together with the Advanced Microwave Sounding Unit (AMSU), represents one of the most advanced spacebased atmospheric sounding systems. The combined AlRS/AMSU system provides radiance measurements used to retrieve temperature profiles with an accuracy of 1 K over 1 km layers under both clear and partly cloudy conditions, while the accuracy of the derived humidity profiles is 15% in 2 km layers. Critical to the successful use of AIRS profiles for weather and climate studies is the use of profile quality indicators and error estimates provided with each profile Aside form monitoring changes in Earth's climate, one of the objectives of AIRS is to provide sounding information of sufficient accuracy such that the assimilation of the new observations, especially in data sparse region, will lead to an improvement in weather forecasts. The purpose of this paper is to describe a procedure to optimally assimilate highresolution AIRS profile data in a regional analysis/forecast model. The paper will focus on the impact of AIRS profiles on a rapidly developing east coast storm and will also discuss preliminary results for a 30-day forecast period, simulating a quasi-operation environment. Temperature and moisture profiles were obtained from the prototype version 5.0 EOS science team retrieval algorithm which includes explicit error information for each profile. The error profile information was used to select the highest quality temperature and moisture data for every profile location and pressure level for assimilation into the ARPS Data Analysis System (ADAS). The AIRS-enhanced analyses were used as initial fields for the Weather Research and Forecast (WRF) system used by the SPORT project for regional weather forecast studies. The ADASWRF system will be run on CONUS domain with an emphasis on the east coast. The preliminary assessment of the impact of the AIRS profiles will focus on quality control issues associated with AIRS, intelligent use of the quality indicators, and forecast verification.

Chou, Shih-Hung↗
NASA NTRS2009

Improving Regional Forecast by Assimilating Atmospheric InfraRed Sounder (AIRS) Profiles into WRF Model

In data sparse regions, remotely-sensed observations can be used to improve analyses and produce improved forecasts. One such source comes from the Atmospheric InfraRed Sounder (AIRS), which together with the Advanced Microwave Sounding Unit (AMSU), represents one of the most advanced space-based atmospheric sounding systems. The purpose of this paper is to describe a procedure to optimally assimilate high resolution AIRS profile data into a regional configuration of the Advanced Research WRF (ARW) version 2.2 using WRF-Var. The paper focuses on development of background error covariances for the regional domain and background type, and an optimal methodology for ingesting AIRS temperature and moisture profiles as separate overland and overwater retrievals with different error characteristics. The AIRS thermodynamic profiles are derived from the version 5.0 Earth Observing System (EOS) science team retrieval algorithm and contain information about the quality of each temperature layer. The quality indicators were used to select the highest quality temperature and moisture data for each profile location and pressure level. The analyses were then used to conduct a month-long series of regional forecasts over the continental U.S. The long-term impacts of AIRS profiles on forecast were assessed against verifying NAM analyses and stage IV precipitation data.

Chou, Shih-Hung↗
NASA NTRS2009

Dynamic Self-Locking of an OEO Containing a VCSEL

A method of dynamic self-locking has been demonstrated to be effective as a means of stabilizing the wavelength of light emitted by a vertical-cavity surface-emitting laser (VCSEL) that is an active element in the frequency-control loop of an optoelectronic oscillator (OEO) designed to implement an atomic clock based on an electromagnetically- induced-transparency (EIT) resonance. This scheme can be considered an alternative to the one described in Optical Injection Locking of a VCSEL in an OEO (NPO-43454), NASA Tech Briefs, Vol. 33, No. 7 (July 2009), page 33. Both schemes are expected to enable the development of small, low-power, high-stability atomic clocks that would be suitable for use in applications involving precise navigation and/or communication. To recapitulate from the cited prior article: In one essential aspect of operation of an OEO of the type described above, a microwave modulation signal is coupled into the VCSEL. Heretofore, it has been well known that the wavelength of light emitted by a VCSEL depends on its temperature and drive current, necessitating thorough stabilization of these operational parameters. Recently, it was discovered that the wavelength also depends on the microwave power coupled into the VCSEL. This concludes the background information. From the perspective that led to the conception of the optical injection-locking scheme described in the cited prior article, the variation of the VCSEL wavelength with the microwave power circulating in the frequency-control loop is regarded as a disadvantage and optical injection locking is a solution of the problem of stabilizing the wavelength in the presence of uncontrolled fluctuations in the microwave power. The present scheme for dynamic self-locking emerges from a different perspective, in which the dependence of VCSEL wavelength on microwave power is regarded as an advantageous phenomenon that can be exploited as a means of controlling the wavelength. The figure schematically depicts an atomic-clock OEO of the type in question, wherein (1) the light from the VCSEL is used to excite an EIT resonance in selected atoms in a gas cell (e.g., 87Rb atoms in a low-pressure mixture of Ar and Ne) and (2) the power supplied to the VCSEL is modulated by a microwave signal that includes components at beat frequencies among the VCSEL wavelength and modulation sidebands. As the VCSEL wavelength changes, it moves closer to or farther from a nearby absorption spectral line, and the optical power transmitted through the cell (and thus the loop gain) changes accordingly. A change in the loop gain causes a change in the microwave power and, thus, in the VCSEL wavelength. It is possible to choose a set of design and operational parameters (most importantly, the electronic part of the loop gain) such that the OEO stabilizes itself in the sense that an increase in circulating microwave power causes the VCSEL wavelength to change in a direction that results in an increase in optical absorption and thus a decrease in circulating microwave power. Typically, such an appropriate choice of operational parameters involves setting the nominal VCSEL wavelength to a point on the shorter-wavelength wing of an absorption spectral line.

Strekalov, Dmitry↗
NASA NTRS2010

Free-Piston Stirling Power Conversion Unit for Fission Surface Power, Phase I Final Report

This report summarizes the design of a 12 kW dual opposed free-piston Stirling convertor and controller for potential future use in space missions. The convertor is heated via a pumped NaK loop and cooling is provided by a pumped water circuit. Convertor efficiency is projected at 27 percent (AC electrical out/heat in). The controller converts the AC electrical output to 120 Vdc and is projected at 91 percent efficiency. A mechanically simple arrangement, based on proven technology, was selected in which the piston is resonated almost entirely by the working space pressure swing, while the displacer is resonated by planar mechanical springs in the bounce space.

Wood, J. Gary↗
NASA NTRS2011

Combustor Computations for CO2-Neutral Aviation

Knowing the pure component C(sub p)(sup 0) or mixture C(sub p) (sup 0) as computed by a flexible code such as NIST-STRAPP or McBride-Gordon, one can, within reasonable accuracy, determine the thermophysical properties necessary to predict the combustion characteristics when there are no tabulated or computed data for those fluid mixtures 3or limited results for lower temperatures. (Note: C(sub p) (sup 0) is molar heat capacity at constant pressure.) The method can be used in the determination of synthetic and biological fuels and blends using the NIST code to compute the C(sub p) (sup 0) of the mixture. In this work, the values of the heat capacity were set at zero pressure, which provided the basis for integration to determine the required combustor properties from the injector to the combustor exit plane. The McBride-Gordon code was used to determine the heat capacity at zero pressure over a wide range of temperatures (room to 6,000 K). The selected fluids were Jet-A, 224TMP (octane), and C12. It was found that each heat capacity loci were form-similar. It was then determined that the results [near 400 to 3,000 K] could be represented to within acceptable engineering accuracy with the simplified equation C(sub p) (sup 0) = A/T + B, where A and B are fluid-dependent constants and T is temperature (K).

Hendricks, Robert C.↗
NASA NTRSDate not supplied

Status of the Development of 3MDCP, the 3-D Woven TPS enabling the Mars Sample Return Earth Entry System

- The Mars Sample Return Earth Entry System is being designed to withstand entry environments of: - Peak Heat Flux of > 3000 W/cm2 - Peak Dynamic Pressure of > 2 atmospheres - Peak Shear of > 3000 Pa. - The TPS Material System Selected to support MSR EES is “3MDCP”, 3D Mid Density Carbon Phenolic. 3MDCP is a derivative of the HEEET material system, using the “Insulation Layer” only. - Implementation of 3MDCP on EES is monolithic instead of a tile architecture in order to meet MSR reliability demands. - The EES TPS Team has recently completed a number of major engineering development milestones in support of delivering the flight 3MDCP TPS hardware: - Weaving Scale-Up completed, > 80” width woven preform production underway - Full Scale Forming & Manufacturing Attrition completed to verify delivered thickness capabilities. - Recent Design Change: EES design has been changed from a 45 degree sphere cone to a 52.5 degree sphere cone to allow for additional system mass.

Z. Young↗
NASA NTRS2024

Enstatite Chondrite Outgassing and Condensate Formation: Implications for Early Atmosphere Development

Early atmospheres on rocky planets where life may develop form through outgassing of their original starting blocks, likely a mixture of chondritic material (carbonaceous chondrites (CC), ordinary chondrites (OC), and enstatite chondrites (EC)). However, there is limited experimental data to inform models connecting a planet’s bulk composition to its early atmospheric properties and thus its possibility for life. Thompson et al. (2021) took a major step for-ward in exploring this knowledge gap by measuring outgassing of 3 volatile-rich CCs, providing important experimental constraints on the initial chemical com-position of early rocky planet atmospheres. These data provided novel insights into the gas chemistry released into evolving atmospheres early in a rocky planet’s history and differed from those currently assumed by many theoretical models of rocky planet atmosphere formation. In this study, we focused on the outgassing and condensation reactions of a primitive EC3, which has a lower intrinsic oxygen fugacity ( ƒ O 2 ) and lower volatile content than the CCC meteorites investigated by. We selected the EC to explore differences between EC and CC in low-pressure, high-temperature outgassing and condensation including S, Cl, Na, and C species.

B A Anzures↗
DOE OSTI2025

Design and Demonstration of a NH3-Fueled Two-Stroke Uniflow Engine for Greenhouse Gas Reduction

The maritime shipping industry is growing increasingly interested in both low and non-carbon-containing fuels to meet future greenhouse gas emission targets. Specifically of interest is ammonia, as it has a relatively high volumetric energy density compared to other future fuels, such as hydrogen, making it more economical to transport. The robust engine architecture of low-speed two-stroke marine engines makes them an ideal candidate for ammonia fuel, overcoming many of the issues surrounding its poor ignitability and low flame speed. If emissions and fueling system challenges can be addressed, retrofits of current low-speed two-stroke dual-fuel engines represent a viable pathway for bringing ammonia engines to market. This study explores these technical hurdles by describing the design, analysis, and experimental validation of a single cylinder research engine converted to operate on ammonia fuel. The engine is a reduced-scale uniflow two-stroke marine engine with two previous hardware configurations available – diesel and high-pressure CNG dual-fuel. A concept study was used to evaluate possible ammonia-fueled engine architectures and the associated tradeoffs and design considerations. With the chosen architecture, low-pressure dual fuel, 1D and 3D analysis tools were used to inform hardware selection and to determine hardware configurations which minimized ammonia-slip. In addition to these considerations the hardware and engine configuration were designed to provide a versatile and robust testing platform. This includes options to test both gaseous and liquid ammonia injection, as well as a wide range of performance parameters such as AFR, swirl, valve timing, SOI, and many others. Design constraints imposed by the existing engine hardware necessitated an iterative loop between design and analysis toolsets, ultimately converging on a final design for the ammonia-conversion hardware. The engine was rebuilt with the new hardware and evaluated in an engine test cell. A new control strategy developed and flashed onto a prototyping electronic control unit allowed for full control over all engine parameters. An initial calibration was developed, providing test data for validation of the engine 1D and 3D models. The impact of the design choices on engine operability and the ability to meet program targets is discussed as well as opportunities for further optimization of the ammonia-conversion hardware, informed by the validated models.

Kaul, Brian [ORNL] (ORCID:0000000184813620)↗
DOE OSTI2022

Kinetics and Reaction Mechanisms of Acetic Acid Hydrodeoxygenation over Pt and Pt–Mo Catalysts

In this work, kinetic measurements for silica-supported Pt and Pt-Mo catalysts were collected in vapor-phase acetic acid hydrodeoxygenation by varying the hydrogen partial pressure between 18 and 72 kPa and acetic acid partial pressure between 7 and 18 kPa at 423-473 K. At all testing conditions, the Pt-Mo catalyst was more active and selective. In addition, the apparent activation energy for Pt-Mo of 76±3 kJ/mol was lower than that of 84±4 kJ/mol for Pt. The apparent reaction orders were also different. The order in hydrogen of 0.8±0.1 for Pt-Mo changed to zero at higher hydrogen partial pressures while that for Pt remained constant at 0.6±0.1. A near-zero order in acetic acid for Pt-Mo changed to -2.1 at higher acetic acid pressures while that for Pt remained constant at -2.9±0.3. These differences in reaction kinetics as well as in selectivity trends with changes in temperature and feed composition indicated a change in the reaction mechanism for Pt-Mo. The catalysts were characterized with hydrogen temperature programmed desorption, oxygen temperature programmed oxidation and transmission electron microscopy with energy-dispersed X-ray spectroscopy elemental mapping. Mo was present in the form of subnanometer-size clusters on the surface of Pt nanoparticles. Both Pt and Pt-Mo catalysts were stable under the reaction conditions for 10 h, and the size and structure of Pt and Pt-Mo particles remained mostly unchanged, without coke accumulation. Density functional theory calculations show that surface acetate is not a major reaction intermediate on both Pt and Pt-Mo and, instead, C-OH bond splitting with the formation of acetyl is the first reaction step in hydrodeoxygenation. The activation energy for this step is dramatically lower on Pt-Mo. Furthermore, the activity of acetyl on Pt-Mo is different. Unlike on pure Pt, the reaction of C-O bond splitting becomes exothermic with a lower activation energy on Pt-Mo, and the reaction of C-C bond splitting, in contrast, becomes endothermic with a higher activation energy, explaining the experimentally observed higher activities and selectivities of Pt-Mo. In addition, the calculations demonstrate that a pair of Pt-Mo surface atoms acts as a single active site where Mo serves as a preferential binding anchor for O atoms. The presence of Mo atoms changes the structure and energy of adsorbed and reacting surface species.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Thermal Property Modeling and Assessment of the Physical Properties of FLiNaK

Here, the thermodynamic properties of the LiF–NaF–KF system and its subsystems were re-evaluated using the CALPHAD method, focusing on the deviations from ideality in the heat capacity [C p (T)] of mixtures, temperature-dependence of mixing enthalpies (Δ mix H), vapor pressures of mixtures, and enthalpies of fusion (ΔH fus ) using reported values and measurements. The results of this work confirmed a pseudoternary eutectic at 732.9 K and 46.5LiF–11.5NaF–42KF mol % (FLiNaK) with determined Cp(T) = 69.822 + 0.000679T + 2,137,152T –2 J mol –1 K –1 (732.9 < T < 1200 K) and ΔH fus = 18,051 J mol –1 in good agreement to the experimental values. The resulting accurate thermodynamic representation can be used to find relevant excess thermochemical properties in the whole pseudoternary space and provide insights into their composition and temperature dependence. A detailed evaluation of select thermophysical properties was also conducted to determine recommended density, thermal diffusivity, thermal conductivity, vapor pressures, and boiling point with calculated uncertainties over the temperature range of interest for FLiNaK–salt energy applications.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
NASA NTRS1974

System for stabilizing cable phase delay utilizing a coaxial cable under pressure

Stabilizing the phase delay of signals passing through a pressurizable coaxial cable is disclosed. Signals from an appropriate source at a selected frequency, e.g., 100 MHz, are sent through the controlled cable from a first cable end to a second cable end which, electrically, is open or heavily mismatched at 100 MHz, thereby reflecting 100 MHz signals back to the first cable end. Thereat, the phase difference between the reflected-back signals and the signals from the source is detected by a phase detector. The output of the latter is used to control the flow of gas to or from the cable, thereby controlling the cable pressure, which in turn affects the cable phase delay.

Clements, P. A.↗
NASA NTRS1992

A satellite anemometer

We present the conceptual design of an instrument that can provide a continuous analog measure of the pitch and yaw angles of a low altitude satellite in the frame of the neutral atmosphere. The device, which uses pressure sensor orientation to provide its signal, can function in an attitude control loop and/or be used to measure atmospheric winds or wave motions. Any arbitrary angle of attack (pitch and yaw) less than +/- 45 deg can be selected for a heading. The sensitivity of the device is 0.1 deg but this would be limited by low ambient pressure at high altitudes and by multiple particle collisions in and below the slip flow region. The development of a prototype flight unit is in progress.

Hanson, W. B.↗
NASA NTRS2016

Active Flow Control Using Sweeping Jet Actuators on a Semi-Span Wing Model

Wind tunnel experiments were performed using active flow control on an unswept semispan wing model with a 30% chord trailing edge flap to aid in the selection of actuators for a planned high Reynolds number experiment. Two sweeping jet actuator sizes were investigated to determine the influence of actuator size on the active flow control system efficiency. Sweeping jet actuators with orifice sizes of 1 mm x 2 mm and 2 mm x 4 mm were selected because of the differences in actuator jet sweep angle. The parameters that were varied include actuator momentum, freestream velocity, and trailing edge flap deflection angle. Steady and unsteady pressure data, Particle Image Velocimetry data, and force and moment data were acquired to assess the performance of the two actuators. In addition to the wind tunnel experiments, benchtop studies of the actuators were performed to characterize the jets produced by each actuator. Benchtop investigations of the smaller actuator reveal that the jet exiting the actuator has a reduced sweep angle compared to published data for larger versions of this type of actuator. The larger actuator produces an oscillating jet that attaches to the external di↵user walls at low supply pressures and produces the expected sweep angles. The AFC results using the smaller actuators show that while the actuators can control flow separation, the selected spacing of 3.3 cm may be too large due to the reduced sweep angle. In comparison, the spacing for the larger actuators, 6.6 cm, appears to be optimal for the Mach numbers investigated. Particle Image Velocimetry results are presented and show how the wall jets produced by the actuators cause the flow to attach to the flap surface.

Melton, LaTunia Pack↗
NASA NTRS1993

Space Shuttle Main Engine performance analysis

For a number of years, NASA has relied primarily upon periodically updated versions of Rocketdyne's power balance model (PBM) to provide space shuttle main engine (SSME) steady-state performance prediction. A recent computational study indicated that PBM predictions do not satisfy fundamental energy conservation principles. More recently, SSME test results provided by the Technology Test Bed (TTB) program have indicated significant discrepancies between PBM flow and temperature predictions and TTB observations. Results of these investigations have diminished confidence in the predictions provided by PBM, and motivated the development of new computational tools for supporting SSME performance analysis. A multivariate least squares regression algorithm was developed and implemented during this effort in order to efficiently characterize TTB data. This procedure, called the 'gains model,' was used to approximate the variation of SSME performance parameters such as flow rate, pressure, temperature, speed, and assorted hardware characteristics in terms of six assumed independent influences. These six influences were engine power level, mixture ratio, fuel inlet pressure and temperature, and oxidizer inlet pressure and temperature. A BFGS optimization algorithm provided the base procedure for determining regression coefficients for both linear and full quadratic approximations of parameter variation. Statistical information relative to data deviation from regression derived relations was also computed. A new strategy for integrating test data with theoretical performance prediction was also investigated. The current integration procedure employed by PBM treats test data as pristine and adjusts hardware characteristics in a heuristic manner to achieve engine balance. Within PBM, this integration procedure is called 'data reduction.' By contrast, the new data integration procedure, termed 'reconciliation,' uses mathematical optimization techniques, and requires both measurement and balance uncertainty estimates. The reconciler attempts to select operational parameters that minimize the difference between theoretical prediction and observation. Selected values are further constrained to fall within measurement uncertainty limits and to satisfy fundamental physical relations (mass conservation, energy conservation, pressure drop relations, etc.) within uncertainty estimates for all SSME subsystems. The parameter selection problem described above is a traditional nonlinear programming problem. The reconciler employs a mixed penalty method to determine optimum values of SSME operating parameters associated with this problem formulation.

Santi, L. Michael↗
DOE OSTI2022

Orbital selective Kondo effect in heavy fermion superconductor UTe2

Abstract Heavy fermion systems emerge from the collective Kondo effect, and their superconductivity can serve as a promising platform for realizing next-generation quantum technologies. However, it has been a great challenge to explore many-body effects in heavy fermion systems with ab-initio approaches. We computed the electronic structure of UTe 2 without purposive judgements, such as intentional selection of on-site Coulomb interaction and disregarding spin-orbit coupling. We show that U-5 f electrons are highly localized in the paramagnetic normal state, giving rise to the Kondo effect. It is also found that the hybridization between U-5 f and U-6 d predominantly in the orthorhombic a b -plane is responsible for the high-temperature Kondo effect. In contrast, the hybridization between U-5 f and Te-5 p along the c -axis manifests the Kondo scattering at a much lower temperature, which could be responsible for the low-temperature upturn of the c -axis resistivity. Our results show that the electron correlation in UTe 2 is orbital selective, which naturally elucidates the recent experimental observations of anomalous temperature dependence of resistivity. Furthermore, we suggest that the Kondo effect is suppressed at high pressure owing to weak localization of magnetic moments, which results from enhanced U-5 f electron hopping. Our discovery provides significant insight toward understanding anisotropic quantum behavior including selective re-entrant superconductivity in heavy fermion UTe 2 .

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗