Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “STAINLESS STEELS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 991 records · Page 55

High temperature oxidation behavior of a high Al-containing ferritic heat-resistant stainless steel

Highlights: • Oxidation kinetics has been analyzed by discontinuous weighing. • Microstructure and phase composition of oxide films were investigated by SEM, EDS and XRD analysis. • The oxidation resistance of 1000 °C is obviously deteriorated comparing with that at 800 °C and 900 °C. • The oxidation mechanism has been discussed. - Abstract: The high temperature oxidation behavior of a high Al-containing ferritic heat-resistant stainless steel at temperatures of 800, 900, and 1000 °C in air were studied in isothermal oxidation tests. The results showed that the isothermal oxidation kinetic curves obtained at different temperatures followed the parabolic law, and the weight gain per unit at 1000 °C was significantly higher than that at 800 and 900 °C. The oxidation rate at 1000 °C was about three times faster than that at 800 and 900 °C. Continuous and compact multicomponent oxide films mainly composed of Cr{sub 2}O{sub 3}, Al{sub 2}O{sub 3}, spinel MnFe{sub 2}O{sub 4}, and MnCr{sub 2}O{sub 4} were obtained at 800 and 900 °C. The oxide film started delaminating at 1000 °C; the outer layer was composed of Cr{sub 2}O{sub 3}, spinel MnCr{sub 2}O{sub 4}, and MnFe{sub 2}O{sub 4}, the middle layer was composed of Fe{sub 2}O{sub 3} and Fe-Cr matrix, and the inner layer was composed of Al{sub 2}O{sub 3} and SiO{sub 2}. Oxidation resistance at 1000 °C was reduced mainly because of porous Fe{sub 2}O{sub 3} and inner oxidation of Al and Si. In addition, the oxidation mechanism was discussed based on kinetic and morphological observations.

36 MATERIALS SCIENCE↗

Surface Preparation of Additively Manufactured 316H Stainless Steel for Molten Salt Applications

Additive manufacturing (AM) has the potential to revolutionize the manufacturing process and speed up deployment of advance nuclear reactors. However, more information is needed on preparing AM materials for extreme reactor environments to qualify AM materials for nuclear applications. This project studies the surface preparation of AM 316H stainless steel using acid pickling and reports a successful procedure for descaling heat-treated AM material.

316H Stainless Steel↗

XRD and EBSD analysis of anisotropic microstructure development in cold rolled F138 stainless steel

The microstructural characteristics of deformation-processed materials highly influence their mechanical properties. For a complete characterization of a microstructure both local and global information must be gathered, which requires the combination of different analysis techniques. X-ray and Electron Backscatter Diffraction were used in the present paper to characterize the deformation induced in a cold rolled F138 austenitic stainless steel sample. The results obtained using laboratory and synchrotron X-ray sources were compared and combined with EBSD quantitative results, allowing the global and local characterization and orientation dependence of the deformation microstructure. A particular behavior was observed in the XRD data corresponding to the planes with < 220 >∥ ND, likely due to a smaller amount of defects accumulated in the crystals with that particular orientation. EBSD was used to separate the scans data into partitions and to calculate misorientation variables and parameters, showing that this behavior can be attributed to a combination of larger grain sizes, lower local boundary misorientations and dislocation densities for crystals having < 220 >∥ ND. Several conclusions, of general validity for the evaluation of microstructure anisotropy, can be extracted from the results. - Highlights: •Combined XRD and EBSD for studying microstructure gave a superb insight on anisotropic accumulation of defects. •W-H and CMWP methods were applied for checking consistency of results. •XRD showed that a smaller accumulation of defects occurred in crystals with < 220 >∥ ND. •High brilliance X-ray beam allowed to study the anisotropy of defect accumulation.

36 MATERIALS SCIENCE↗

Characterization of Defocused Electron Beams and Welds in Stainless Steel and Refractory Metals using the Enhanced Modified Faraday Cup Diagnostic

As the first part of a project to compare new generation, continuous wave, laser welding technology to traditional electron beam welding technology, electron beam welds were made on commercially pure vanadium refractory metal and 21-6-9 austenitic stainless steel. The electron beam welds were made while employing EB diagnostics to fully characterize the beams so that direct comparisons could be made between electron beam and laser beams and the welds that each process produces.

36 MATERIALS SCIENCE↗

Investigation of AISI 441 Ferritic Stainless Steel and Development of Spinel Coatings for SOFC Interconnect Applications

As part of an effort to develop cost-effective ferritic stainless steel-based interconnects for solid oxide fuel cell (SOFC) stacks, both bare and spinel coated AISI 441 were studied in terms of metallurgical characteristics, oxidation behavior, and electrical performance. The conventional melt metallurgy used for the bulk alloy fabrication leads to significant processing cost reduction and the alloy chemistry with the presence of minor alloying additions of Nb and Ti facilitate the strengthening by precipitation and formation of Laves phase both inside grains and along grain boundaries during exposure in the intermediate SOFC operating temperature range. The Laves phase formed along the grain boundaries also ties up Si and prevents the formation of an insulating silica layer at the scale/metal interface during prolonged exposure. The substantial increase in ASR during long term oxidation due to oxide scale growth suggested the need for a conductive protection layer, which could also minimize Cr evaporation. In particular, Mn1.5Co1.5O4 based surface coatings on planar coupons drastically improved the electrical performance of the 441, yielding stable ASR values at 800ºC for over 5,000 hours. Ce-modified spinel coatings retained the advantages of the unmodified spinel coatings, and also appeared to alter the scale growth behavior beneath the coating, leading to a more adherent scale. The spinel protection layers appeared also to improve the surface stability of 441 against the anomalous oxidation that has been observed for ferritic stainless steels exposed to dual atmosphere conditions similar to SOFC interconnect environments. Hence, it is anticipated that, compared to unmodified spinel coatings, the Ce-modified coatings may lead to superior structural stability and electrical performance.

30 DIRECT ENERGY CONVERSION↗

Investigation of Deformation Behavior of Additively Manufactured AISI 316L Stainless Steel with In Situ Micro-Compression Testing

Additive manufacturing techniques are being used more and more to perform the precise fabrication of engineering components with complex geometries. The heterogeneity of additively manufactured microstructures deteriorates the mechanical integrity of products. In this paper, we printed AISI 316L stainless steel using the additive manufacturing technique of laser metal deposition. Both single-phase and dual-phase substructures were formed in the grain interiors. Electron backscatter diffraction and energy-dispersive X-ray spectroscopy indicate that Si, Mo, S, Cr were enriched, while Fe was depleted along the substructure boundaries. In situ micro-compression testing was performed at room temperature along the [001] orientation. The dual-phase substructures exhibited lower yield strength and higher Young’s modulus compared with single-phase substructures. Our research provides a fundamental understanding of the relationship between the microstructure and mechanical properties of additively manufactured metallic materials. The results suggest that the uneven heat treatment in the printing process could have negative impacts on the mechanical properties due to elemental segregation.

36 MATERIALS SCIENCE↗

Wet oxidation of stainless steels: New insights into hydrogen ingress

detrimental effect. However, the complexities of tracking hydrogen in these materials have prevented the direct profiling of hydrogen ingress needed to understand these phenomena. Here we report hydrogen profiles in industrially-relevant alumina- and chromia-forming steels correlated with the local oxidemetal nano/microstructure by use of SIMS D2O tracer studies and experimental protocols to optimize D retention. The D profiles unexpectedly varied markedly among the alloys examined, which indicates mechanistic complexity but also the potential to mitigate detrimental water vapor effects by manipulation of alloy chemistry.

08 HYDROGEN↗

Aluminum nanocomposites having wear resistance better than stainless steel

Tribological behavior of alumina-particle-reinforced aluminum composites made by powder metallurgy process has been investigated. The nanocomposite containing 15 vol% of Al2O3 nanoparticles exhibits excellent wear resistance by showing significantly low wear rate and abrasive wear mode. The wear rate of the nanocomposite is even lower than stainless steel. We have also demonstrated that such excellent wear resistance only occurred in the composite reinforced with the high volume fraction of nanosized reinforcing particles. The results were discussed in terms of the microstructure of the nanocomposite.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Quantification of solution annealing effects on microstructure and property in a laser powder bed fusion 316H stainless steel

Solution annealing (SA) is an effective way to mitigate microstructural heterogeneity and to optimize mechanical performance of alloys manufactured by laser powder bed fusion (LPBF). In this study, a comprehensive and quantitative understanding of the recovery and recrystallization processes in the SA temperature range of LPBF 316H stainless steel is provided using results from analytical electron microscopy and in-situ high-energy synchrotron x-ray scattering. The profound effect of dislocation structures and secondary phase particles on mechanical performance, particularly under tension and creep conditions, is rationalized using deformation models that incorporate microstructural inputs. This study, for the first time, quantifies the broad effect of nano oxide inclusions on dislocation recovery kinetics, on grain growth and recrystallization kinetics, and on tension strength and creep resistance. The fundamental differences between the LPBF and the conventional wrought materials are revealed. The findings address critical questions in post-build processing of AM materials and pave the way for their rapid qualification for high temperature applications.

In-situ X-ray diffraction↗

Improved Accident Tolerance of Austenitic Stainless Steel Cladding through Colossal Supersaturation with Interstitial Solutes

We proposed a program-supporting research project in the area of fuel-cycle R&D, specifically on the topic of advanced fuels. Our goal was to investigate whether SECIS (surface engineering by concentrated interstitial solute – carbon, nitrogen) can improve the properties of austenitic stainless steels and related structural alloys such that they can be used for nuclear fuel cladding in LWRs (light-water reactors) and significantly excel currently used alloys with regard to performance, safety, service life, and accident tolerance. We intended to demonstrate that SECIS can be adapted for post-processing of clad tubing to significantly enhance mechanical properties (hardness, wear resistance, and fatigue life), corrosion resistance, resistance to stress–corrosion cracking (hydrogen-induced embrittlement), and – potentially – radiation resistance (against electron-, neutron-, or ion-radiation damage). To test this hypothesis, we measured various relevant properties of the surface-engineered alloys and compared them with corresponding properties of the non–treated, as-received alloys. In particular, we studied the impact of heat exposure corresponding to BWR (boiling-water reactor) working and accident (loss-of-coolant) conditions and the effect of ion irradiation.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Use of in-situ TEM to characterize the deformation-induced martensitic transformation in 304 stainless steel at cryogenic temperature

Highlights: • Unique experimental visualization of DIM transformation in 304SS in-situ in a TEM at cryogenic temperatures. • Three cases of DIM were captured in situ showing how stress and temperature are both effective on the transformation. • (i) formation of ε- martensite through overlapping/bundling of SFs (γ →SFs →ε), • (ii) direct (γ→ α’) transformation with interface migration upon pulling the sample at constant temperature, • (iii) direct γ→ α’ transformation upon cooling, without further pulling the sample. - Abstract: Tensile tests are conducted in-situ in a TEM at cryogenic temperatures (from − 100 °C to 0 °C) using a cooling TEM straining-stage with the goal of capturing the growth of the martensitic phase as it develops under stress in the material. The in-situ technique is used to explore the mechanism of deformation induced martensitic transformation in 304 and 304L austenitic stainless steels. The formation of stacking faults is captured, as well as the subsequent formation of ε-martensite, confirming the role played by Stacking faults (SFs) as intermediate step during the transformation from γ-austenite to ε-martensite. In addition, direct transformation from γ-austenite to α′-martensite is captured (i) upon straining at a fixed temperature and (ii) upon cooling after pulling on the sample, indicating how straining and temperature are both effective on the transformation.

36 MATERIALS SCIENCE↗

Plastic deformation and creep damage evaluations of type 316 austenitic stainless steels by EBSD

The inspection method of plastic and/or creep deformations has been required as the quantitative damage estimation procedure for structural components especially used in electric power plants. In this study, the method using electron backscatter diffraction (EBSD) was applied to the deformation and damage evaluation of austenitic stainless steels strained by tension or compression at room temperature and also tested in creep at high temperature. It was found that the value of Grain Average Misorientation (GAM) which showed the average misorientation for the whole observed area including over several dozen grains, was a very useful parameter for quantifying the microstructural change as either the plastic or creep strain increased. The unique linear correlation was obtained between GAM and plastic strain in tension and compression. For creep damage evaluation, the difference of grain average misorientation from the value of the unstrained specimen ({Delta}GAM) showed an excellent correlation with the inelastic strain below strain at which the tertiary creep began.

36 MATERIALS SCIENCE↗

The effect of secondary phases on microstructure and irradiation damage in an as-built additively manufactured 316 L stainless steel with a hafnium compositional gradient

Additive manufacturing (AM) or rapid prototyping has become a crucial tool for reducing both cost and time while increasing efficiency in qualifying structural materials for reactor use. In this study, directed energy deposition (DED) was used to develop an as-built 316 L stainless steel sample with three regions of increasing Hf-dopant to study the effects of Hf on the irradiation response of the material. Morphological and microstructural changes were analyzed before and after 2 MeV proton irradiation at 360 °C to a damage of 2.5 dpa at ~ 10 µm below the surface. The addition of Hf effectively suppressed radiation-induced damage (dislocation loops, radiation-induced segregation) due to enhanced point defect recombination. The radiation damage seen in the as-built sample was further compared to a thermo-mechanically treated counterpart of the same fabrication and irradiation parameters which was found to behave superiorly. In conclusion, the increased radiation resistance of this material may be attributed to the as-built microstructure, which includes undissolved Hf particles, delta ferrite grains and cellular sub-grain boundaries that can hinder defect motion.

316L Stainless Steel↗

Simulation of Drawing of Small Stainless Steel Platinum Medical Tubes--Influence of the Tool Parameters on the Forming Limit

Tube cold drawing processes are used to reduce tube diameters and thickness, while pulling them through a conical converging die with or without inner plug. An accurate modelling of the material deformation and friction behaviour is required in order to well describe these processes.The study concerns a stainless steel platinum alloy. The material behaviour is characterised through tensile tests at strain rates as close as possible to the high strain rates reached during the drawing process. The results are fitted with an isotropic temperature-independent Johnson Cook constitutive equation. The modelling of floating plug drawing is performed on a ABAQUS/Explicit model. Friction coefficient is difficult to estimate with mechanical experimental tests, thus an inverse analysis is carried out to fit this parameter thanks to finite element simulation and experimental drawing tests. Drawing force measurements are recorded during the forming process. The Cockroft-Latham criterion is applied to understand the different process parameters influence on tube drawing and its accuracy for drawing process is evaluated.

42 ENGINEERING↗

Pulsed TIG Welding–Brazing of Aluminum–Stainless Steel with an Al-Cu Twin Hot Wire

A TIG welding–brazing process with a twin aluminum hot wire technique was utilized to control the heat input, improve the joint formation, suppress the interfacial intermetallic compounds (IMCs) and increase the joint strength, thereby creating reliable joints between an aluminum alloy and stainless steel with an ER2319 filler. Twin wires with reasonable diameters and filling modes led to a satisfactory weld of parent metals with varying thicknesses. By the hot wire technique, the reasonable range of the welding current was extended and the thickness of the interfacial IMC at the seam bottom was reduced. In addition, both the tensile strength and stability of the joints increased compared with a cold wire. The IMC consisted of θ-(Fe,Cu){sub 4}Al{sub 13} and minor Cr{sub 0.7}Fe{sub 0.3}Al{sub 6}, and the precipitated phases in the weld were Al{sub 2}Cu and Al{sub 2}CuMg. With an increasing welding current, the IMC thickness significantly increased, while the joint strength decreased. The fracture positions of the joints varied with the corresponding welding currents.

36 MATERIALS SCIENCE↗

In Situ Neutron Diffraction Study of the Influence of Microstructure on the Mechanical Response of Additively Manufactured 304L Stainless Steel

In situ neutron diffraction measurements were completed for this study during tensile and compressive deformation of stainless steel 304L additively manufactured (AM) using a high power directed energy deposition process. Traditionally produced wrought 304L material was also studied for comparison. The AM material exhibited roughly 200 MPa higher flow stress relative to the wrought material. Crystallite size, crystallographic texture, dislocation density, and lattice strains were all characterized to understand the differences in the macroscopic mechanical behavior. The AM material’s initial dislocation density was about 10 times that of the wrought material, and the flow strength of both materials obeyed the Taylor equation, indicating that the AM material’s increased yield strength was primarily due to greater dislocation density. Finally, a ~50 MPa flow strength tension/compression asymmetry was observed in the AM material, and several potential causes were examined.

36 MATERIALS SCIENCE↗

Radiation response of a Fe–20Cr–25Ni austenitic stainless steel under Fe 2+ irradiation at 500 °C

The radiation response of a Fe–20Cr–25Ni austenitic stainless steel under self-ion irradiation at 500 °C was systematically investigated. The steel was irradiated at 500 °C by 3.5 MeV Fe 2+ ions to 10, 50, and 150 peak dpa, respectively. In the 200–400 nm depth region, radiation-induced Frank loops were relatively stable in both size and number density from 10 to 150 peak dpa. Anisotropic distribution of Frank loops was observed in the 50 and 150 peak dpa specimens, possibly due to interaction of Frank loops and network dislocations with preferred orientations. Coarse voids were found only in the 50 and 150 peak dpa specimens in depths less than 750 nm, suggesting that injected interstitials at deeper regions suppressed the void nucleation. The peak swelling was very low (~0.4%) for both 50 and 150 peak dpa irradiation. Radiation also led to the formation of intragranular plate-like Cr-rich carbides. Radiation-induced segregation of Ni and Si was found at various sinks: dislocation loops, void surfaces, and carbide-matrix interfaces. Finally, irradiation hardening was measured by nanoindentation and the results are consistent with microstructure-based calculations using the dispersed barrier hardening model. The major contributor to irradiation hardening changed from Frank loops at the lowest dose to network dislocations at the highest dose.

dislocation loops↗

Fatigue damage evaluation of austenitic stainless steel using nonlinear ultrasonic waves in low cycle regime

The interrupted low cycle fatigue test of austenitic stainless steel was conducted and the dislocation structure and fatigue damage was evaluated subsequently by using both transmission electron microscope and nonlinear ultrasonic wave techniques. A “mountain shape” correlation between the nonlinear acoustic parameter and the fatigue life fraction was achieved. This was ascribed to the generation and evolution of planar dislocation structure and nonplanar dislocation structure such as veins, walls, and cells. The “mountain shape” correlation was interpreted successfully by the combined contribution of dislocation monopole and dipole with an internal-stress dependent term of acoustic nonlinearity.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗