Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SPUTTERING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 991 records · Page 55

Magnetron-sputter deposition of high-indium-content n-AlInN thin film on p-Si(001) substrate for photovoltaic applications

Al{sub 0.278}In{sub 0.722}N thin films have been grown on p-type Si(001) and c-plane sapphire substrates by employing radio-frequency magnetron-sputter deposition at elevated temperatures. High-resolution x-ray diffraction, as well as pole-figure measurements, reveals no phase separation of the thin films. The Al{sub 0.278}In{sub 0.722}N film grown on p-Si(001) substrate is a typical fiber-texture with AlInN(0001)//Si(001) while that on the c-sapphire exhibits the onset of epitaxy. Microscopic studies reveal that the growth is dominated by a columnar mechanism and the average columnar grain diameter is about 31.5 and 50.8 nm on p-Si(001) and c-sapphire substrates, respectively. Photoluminescence at room-temperature exhibits a strong emission peak at 1.875 eV, smaller than the optical absorption edge (2.102 eV) but larger than the theoretical bandgap energy (1.70 eV), which is attributable to the band-filling effect, as is supported by the high electron density of 4.5 Multiplication-Sign 10{sup 20} cm{sup -3}. The n-Al{sub 0.278}In{sub 0.722}N/p-Si(001) heterostructure is tested for solar cells and the results are discussed based on the I-V characteristics and their fittings.

36 MATERIALS SCIENCE↗

Electric field assisted sputtering of Fe{sub 3}O{sub 4} thin films and reduction in anti-phase boundaries

Fe{sub 3}O{sub 4} thin films have been prepared by a new approach of in-situ electric field assisted sputtering. Raman shift, {rho}(T), and M(T) measurements reveal a reduction in anti-phase boundaries (APBs), which is explained by the electric field induced surface diffusion favouring [111] oriented growth with lesser defects. Early magnetization saturation (4 kOe) and its higher value (441 emu/cm{sup 3}), low electron phonon coupling constant (0.48), sharp Verwey transition {Delta}T{sub V} = 12 K, Arrhenius law of conduction via delocalized states above T{sub V} and lower value of localization radius (1.5 nm) below T{sub V} compared to that observed in un-assisted films confirmed that the electric field assisted grown films are nearly free from anti-phase boundaries.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Electrical and optical properties of Ta-Si-N thin films deposited by reactive magnetron sputtering

The electrical and optical properties of Ta{sub x}Si{sub y}N{sub z} thin films deposited by reactive magnetron sputtering from individual Ta and Si targets were studied in order to investigate the effects of nitrogen and silicon contents on both properties and their correlation to the film microstructure. Three sets of fcc-Ta{sub x}Si{sub y}N{sub z} thin films were prepared: sub-stoichiometric Ta{sub x}Si{sub y}N{sub 0.44}, nearly stoichiometric Ta{sub x}Si{sub y}N{sub 0.5}, and over-stoichiometric Ta{sub x}Si{sub y}N{sub 0.56}. The optical properties were investigated by near-normal-incidence reflectivity and ellipsometric measurements in the optical energy range from 0.375 eV to 6.8 eV, while the d.c. electrical resistivity was measured in the van der Pauw configuration from 20 K to 300 K. The optical and electrical measurements were interpreted using the standard Drude-Lorentz model and the so-called grain boundary scattering model, respectively. The electronic properties were closely correlated with the compositional and structural modifications of the Ta{sub x}Si{sub y}N{sub z} films due to variations in the stoichiometry of the fcc-TaN{sub z} system and the addition of Si atoms. According to the nitrogen and silicon contents, fcc-Ta{sub x}Si{sub y}N{sub z} films can exhibit room temperature resistivity values ranging from 10{sup 2} {mu}{Omega} cm to about 6 Multiplication-Sign 10{sup 4} {mu}{Omega} cm. The interpretation of the experimental temperature-dependent resistivity data within the Grain Boundary Scattering model, combined with the results from optical investigations, showed that the mean electron transmission probability G and the free carriers concentration, N, are the main parameters that control the transport properties of these films. The results indicated that the correlation between electrical and optical measurements with the chemical composition and the nanostructure of the Ta{sub x}Si{sub y}N{sub z} thin films provides a pertinent and consistent description of the evolution of the Ta-Si-N system from a solid solution to a nanocomposite material due to the addition of Si atoms.

36 MATERIALS SCIENCE↗

Impact of the surface-near silicon substrate properties on the microstructure of sputter-deposited AlN thin films

In micro-/nanomachined devices and systems, aluminum nitride (AlN) thin films are widely used due to their piezoelectric properties. This work evaluates the potential of modifying the interface between the AlN thin film and the silicon (Si) wafer serving as bottom electrode for optimized crystallographic orientation and, hence, improved electrical and piezoelectric properties. The films were analyzed using temperature-dependant leakage current measurements, transmission electron microscopy, and x-ray diffraction. By preconditioning of the Si substrate surface applying sputter etching prior to film deposition, leakage current levels are substantially decreased and an increased (002) orientation of the AlN grains is observed.

36 MATERIALS SCIENCE↗

Structural and optical properties of zinc oxide film using RF-sputtering technique

This paper reports the fabrication of zinc oxide (ZnO) film using RF-sputtering technique. Determination of the structural properties using High Resolution X-ray Diffraction (HRXRD) confirmed that ZnO film deposited on silicon (Si) substrate has a high quality. This result is in line with the Scanning Electron Microscopy (SEM) and Atomic Force Microscopy (AFM) which were used to image the morphology of the film, in which a rough surface was demonstrated. Photoluminescence (PL) emission is included to study the optical properties of ZnO film that shows two PL peak in the UV region at 371 nm and in visible region at 530 nm respectively.

36 MATERIALS SCIENCE↗

The effect of native oxide on ion-sputtering-induced nanostructure formation on GaSb surfaces

We have investigated the influence of native oxides on ion-sputtering-induced nanostructure formation on GaSb using in situ low energy ion scattering spectroscopy (LEISS) and X-ray photoelectron spectroscopy (XPS). Comparing an oxygen-free sample with a native oxide sample, LEISS and XPS reveal the effect of oxygen in generating higher surface Ga fractions during early stages (fluences of 1 Multiplication-Sign 10{sup 15}-1 Multiplication-Sign 10{sup 16} cm{sup -2}) of low energy (<100 eV) Ar+ irradiation. Enhanced surface Ga and Ga{sub 2}O{sub 3} fractions were also observed on 'oxide free' samples exposed to air following irradiation. The results suggest preferential Ga oxidation and segregation on the top of the amorphous layer if oxygen is present on the surface. In addition, the native oxide also increases the fluence threshold for nanopatterning of GaSb surfaces by almost a factor of four during low energy irradiation.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Reactive sputter magnetron reactor for preparation of thin films and simultaneous in situ structural study by X-ray diffraction

The purpose of the designed reactor is (i) to obtain polycrystalline and/or amorphous thin films by controlled deposition induced by a reactive sputtering magnetron and (ii) to perform a parallel in situ structural study of the deposited thin films by X-ray diffraction, in real time, during the whole growth process. The designed reactor allows for the control and precise variation of the relevant processing parameters, namely, magnetron target-to-sample distance, dc magnetron voltage, and nature of the gas mixture, gas pressure and temperature of the substrate. On the other hand, the chamber can be used in different X-ray diffraction scanning modes, namely, {theta}-2{theta} scanning, fixed {alpha}-2{theta} scanning, and also low angle techniques such as grazing incidence small angle X-ray scattering and X-ray reflectivity. The chamber was mounted on a standard four-circle diffractometer located in a synchrotron beam line and first used for a preliminary X-ray diffraction analysis of AlN thin films during their growth on the surface of a (100) silicon wafer.

36 MATERIALS SCIENCE↗

Crystal structure and magnetic properties of Zn{sub 0.9}Cu{sub 0.1}O{sub y} rf-sputtered thin films

Zn{sub 0.9}Cu{sub 0.01}O thin films were deposited on quartz substrates by rf-magnetron sputtering using ceramic target in pure argon gas environment. The X-ray diffraction show the polycrystalline wurtzite structure of the films. The average grain size increases from 40-100nm as thickness of the film increases. The room temperature magnetization studies show the films to be ferromagnetic. The saturation magnetization decreases with increase in film thickness.

36 MATERIALS SCIENCE↗

Preparation and characterization of Gd{sub 2}O{sub 3} thin films by RF magnetron sputtering

Gd{sub 2}O{sub 3} films were deposited on to glass substrates held at room temperature using radio frequency (RF) magnetron sputtering, at a RF power of 63 W and argon pressure maintained at 1 Multiplication-Sign 10{sup -2}mbar. The morphology was studied by field emission scanning electron microscopy (FESEM) and atomic force microscopy (AFM). The band gaps obtained from optical absorption studies are in the range of 3.4 and 4.02 eV, after annealing in air at 380 Degree-Sign C for 1 hour.

36 MATERIALS SCIENCE↗

Oxygen partial pressure influenced structural and optical properties of DC magnetron sputtered ZrO{sub 2} films

Thin films of zirconium oxide (ZrO{sub 2}) were deposited on (100) p-silicon and quartz substrates by sputtering of metallic zirconium target under different oxygen partial pressures in the range 8 Multiplication-Sign 10{sup -3}-6 Multiplication-Sign 10{sup -2}Pa. The effect of oxygen partial pressure on the structural and optical properties of the deposited films was systematically investigated. The deposition rate of the films decreased from 3.3 to 1.83 nm/min with the increase of oxygen partial pressure from 8 Multiplication-Sign 10{sup -3}-6 Multiplication-Sign 10{sup -2}Pa respectively. The X-ray diffraction profiles revealed that the films exhibit (111) refection of zirconium oxide in monoclinic phase. The optical band gap of the films increased from 5.62 to 5.80 eV and refractive index increased from 2.01 to 2.08 with the increase of oxygen partial pressure from 8 Multiplication-Sign 10{sup -3}-6 Multiplication-Sign 10{sup -2}Pa respectively.

36 MATERIALS SCIENCE↗

Electrochemical properties of magnetron sputtered WO{sub 3} thin films

Thin films of tungsten oxide (WO{sub 3}) were deposited on ITO substrates by using RF magnetron sputtering at oxygen and argon atmospheres of 6 Multiplication-Sign 10{sup -2}Pa and 4 Pa respectively. The chemical composition and surface morphology of the WO{sub 3} thin films have been studied by X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM) respectively. The results indicate that the deposited WO{sub 3} thin films are nearly stoichiometric. The electrochemical performances of the WO{sub 3} thin films have been evaluated by galvonostatic charging/discharging method. The discharge capacity was 15{mu}Ah/cm{sup 2}{mu}m at the initial cycle and faded rapidly in the first few cycles and stabilized at a lesser stage.

36 MATERIALS SCIENCE↗

Influence of RF power on magnetron sputtered AZO films

Al-doped Zinc Oxide (AZO) transparent conducting films are prepared on glass substrate by RF magnetron sputtering under different RF power with a 3 inch diameter target of 2 wt%Al{sub 2}O{sub 3} in zinc oxide. The effect of RF power on the structural, optical and electrical properties of AZO films was investigated by X-ray Diffraction (XRD), Hall measurement and UV-Visible spectrophotometry. The XRD data indicates a preferential c-axis orientation for all the films. All films exhibit high transmittance (<90%) in visible region. Films deposited at 60 W power exhibit lowest resistivity of 5.7 Multiplication-Sign 10{sup -4}{omega}cm. Such low-resistivity and high-transmittance AZO films when prepared using low RF power at room temperature could find important applications in flexible electronics.

36 MATERIALS SCIENCE↗

Studies of thin films of Ti- Zr -V as non-evaporable getter films prepared by RF sputtering

Non-Evaporable Getter (NEG) films of the Ti-Zr-V prepared on stainless steel substrates by Radio Frequency sputtering. To observe its getter behavior at the lowest activation temperature, the sample is heated continuously at different temperatures (100 Degree-Sign C, 150 Degree-Sign C, 200 Degree-Sign C and 250 Degree-Sign C) for 2 hours. The changes of the surface chemical composition at different temperaturesare analyzed by using XPS and SEM (Scanning Electron Microscopy) techniques. The volume elemental composition of the film has been measured by energy dispersive X-ray spectroscopy (EDX). The in-situ XPS measurements of the activated getter films show the disappearance of the superficial oxide layer through the variation in the oxygen stoichiometry during thermal activation. Results of these studies show that the deposited films of Ti-Zr-V could be used as NEG to produce extreme high vacuum.

36 MATERIALS SCIENCE↗

Controlled polarity of sputter-deposited aluminum nitride on metals observed by aberration corrected scanning transmission electron microscopy

The polarity determination process of sputter-deposited aluminum nitride (AlN) on metals has been analyzed using aberration corrected atomic resolution scanning transmission electron microscope. Direct growth of c-axis orientated AlN on face centered cubic metals (fcc) (111) with the local epitaxy has been observed, and the polarity was determined at the AlN/metal interface. We found that the AlN polarity can be controlled by the base metal layer: N-polarity AlN grows on Pt(111) while Al-polarity AlN forms on Al(111). Based on these results, the growth mechanism of AlN on metals is discussed.

36 MATERIALS SCIENCE↗

Low substrate temperature fabrication of high-performance metal oxide thin-film by magnetron sputtering with target self-heating

Al-doped ZnO (AZO) films with high transmittance and low resistivity were achieved on low temperature substrates by radio frequency magnetron sputtering using a high temperature target. By investigating the effect of target temperature (T{sub G}) on electrical and optical properties, the origin of electrical conduction is verified as the effect of the high T{sub G}, which enhances crystal quality that provides higher mobility of electrons as well as more effective activation for the Al dopants. The optical bandgap increases from 3.30 eV for insulating ZnO to 3.77 eV for conducting AZO grown at high T{sub G}, and is associated with conduction-band filling up to 1.13 eV due to the Burstein-Moss effect.

36 MATERIALS SCIENCE↗

Quasi-two-dimensional conducting layer on TiO{sub 2} (110) introduced by sputtering as a template for resistive switching

The insulator-to-metal transformation in the surface layer of TiO{sub 2} (110) induced by the Ar{sup +} ion sputtering process is analyzed on the nanoscale. Local conductivity atomic force microscopy and photoelectron spectroscopy allow the changes in the valence of the Ti ions in the surface layer to be linked to the formation of its grain-like structure. The investigation of the cleavage plane of the crystal allowed us to estimate the thickness of the quasi-two-dimensional conducting layer generated by ion bombardment as 30 nm. The conducting layer is a template where the resistive switching of each single grain can be carried out.

36 MATERIALS SCIENCE↗

Hydrogen incorporation induced metal-semiconductor transition in ZnO:H thin films sputtered at room temperature

The room temperature deposited ZnO:H thin films having high conductivity of 500 Ohm-Sign {sup -1} cm{sup -1} and carrier concentration reaching 1.23 Multiplication-Sign 10{sup 20} cm{sup -3} were reactively sputter deposited on glass substrates in the presence of O{sub 2} and 5% H{sub 2} in Ar. A metal-semiconductor transition at 165 K is induced by the increasing hydrogen incorporation in the films. Hydrogen forms shallow donor complex with activation energy of {approx}10-20 meV at oxygen vacancies (V{sub O}) leading to increase in carrier concentration. Hydrogen also passivates V{sub O} and V{sub Zn} causing {approx}4 times enhancement of mobility to 25.4 cm{sup 2}/V s. These films have potential for use in transparent flexible electronics.

36 MATERIALS SCIENCE↗

The role of the (111) texture on the exchange bias and interlayer coupling effects observed in sputtered NiFe/IrMn/Co trilayers

Magnetic properties of sputtered NiFe/IrMn/Co trilayers grown on different seed layers (Cu or Ta) deposited on Si (100) substrates were investigated by magnetometry and ferromagnetic resonance measurements. Exchange bias effect and magnetic spring behavior have been studied by changing the IrMn thickness. As shown by X-ray diffraction, Ta and Cu seed layers provoke different degrees of (111) fcc-texture that directly affect the exchange bias and indirectly modify the exchange spring coupling behavior. Increasing the IrMn thickness, it was observed that the coupling angle between the Co and NiFe ferromagnetic layers increases for the Cu seed system, but it reduces for the Ta case. The results were explained considering (i) different anisotropies of the Co and IrMn layers induced by the different degree of the (111) texture and (ii) the distinct exchange bias set at the NiFe/IrMn and IrMn/Co interfaces in both systems. The NiFe and Co interlayer coupling angle is strongly correlated with both exchange bias and exchange magnetic spring phenomena. It was also shown that the highest exchange bias field occurs when an unstressed L1{sub 2} IrMn structure is stabilized.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗