Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SOOT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 991 records · Page 55

Properties and Autoignition Reactivity of Diesel Boiling Range Ethers Produced from Guerbet Alcohols

We examine the properties of diesel boiling range ethers made from coupling of alcohols produced by oligomerization of ethanol (Guerbet alcohols) for their utility as low-carbon liquid fuel blendstocks. Basic properties of boiling point, flash point, freezing point, density and viscosity are well suited for blending into diesel fuels. For the mixture of ethers the lightest component, di-n-butyl ether, can be present at up to 20 vol% while still having adequately high flashpoint for safe handling. Soot formation tendency (as yield sooting index) is well below that of conventional diesel. The ethers have similar compatibility with elastomers as conventional diesel, based on Hansen solubility parameter analysis. Oxidation stability was assessed for 30 vol% blends of individual ethers in a conventional diesel fuel using a long-term storage test. Over 6 weeks we observed no formation of peroxides or degradation. n-alkyl ethers with carbon number of 8 or higher have cetane number over 100, which is outside the defined range of cetane number, while branched ethers are over 70. The ethers also blend antagonistically into conventional diesel for cetane number, meaning that the blend cetane value is lower than predicted based on a linear by volume, mass, or mole model. We show that aromatics and naphthenes likely act as radical scavengers to slow or shut down autoignition of the highly reactive ethers at low to medium blend levels. Overall, diesel boiling range ethers show significant promise as high quality low-net carbon diesel blendstocks.

09 BIOMASS FUELS↗

Synthesis and catalytic properties of microemulsion-derived cerium oxide nanoparticles

The synthesis of cerium dioxide nanoparticles using an inverse microemulsion technique and precipitation method was investigated. Cerium hydroxide nanoparticles were synthesized by adding diluted ammonia to n-heptane-surfactant-cerium nitrate system. The micelle and particle size in the range of 5-12 nm were controlled by varying the molar water to surfactant ratio and analyzed by dynamic light scattering (DLS), small angle X-ray scattering (SAXS) and high-resolution transmission electron microscopy (HRTEM). Cerium hydroxide nanoparticles were isolated and subsequently treated at 100-600 deg. C to obtain nanoscale ceria. Crystallite sizes of cerium dioxide in the range of 6-16 nm were estimated by Scherrer analysis by X-ray diffraction (XRD) and HRTEM. The catalytic activity of particles annealed at 400 and 600 deg. C in soot combustion reactions was characterized by temperature-programmed oxidation (TPO) indicating a size-dependant activity. Crystallite sizes and catalytic stability of elevated ceria systems were tested in second combustion cycles. - Graphical abstract: The synthesis of cerium dioxide nanoparticles using an inverse microemulsion technique and precipitation method was investigated using small angle X-ray scattering, dynamic light scattering and high-resolution transmission electron microscopy. Catalytic activity of ceria nanoparticles was tested in soot combustion reaction indicating size-dependent reactivity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Synthesis of carbon-coated iron nanoparticles by detonation technique

Carbon-coated iron nanoparticles were synthesized by detonating a mixture of ferrocene, naphthalene and hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX) in an explosion vessel under low vacuum conditions (8.1 kPa). The RDX functioned as an energy source for the decomposition of ferrocene and naphthalene. The carbon-coated iron nanoparticles were formed as soot-like deposits on the inner surface of the reactor, which were characterized by XRD, TEM, HRTEM, Raman spectroscopy and vibrating sample magnetometer. And a portion of the detonation soot was treated with hydrochloric acid. The product was carbon-coated nanoparticles in perfect core-shell structures with graphitic shells and bcc-Fe cores. The detonation technique offers an energy-saving route to the synthesis of carbon-coated nanomaterials.

36 MATERIALS SCIENCE↗

Synthesis and catalytic application of nanofibrous La{sub 0.9}A{sub 0.1}MnO{sub 3} (A = Ca, Cu, Ag) with macroscopic shapes

Graphical abstract: Fabrication of nanofibrous La{sub 0.9}A{sub 0.1}MnO{sub 3} (A = Ca, Cu, Ag) perovskite-type oxides with macroscopic shapes was successfully obtained using carbon nanofibers (CNFs) as templates. Furthermore, their application for the combustion of carbon black (CB), which is a model of particulate matter exhausted from diesel engines, was demonstrated. - Highlights: • Nanofibrous La{sub 0.9}A{sub 0.1}MnO{sub 3} with macroscopic shapes was successfully obtained. • CNFs template method used here is facile, effective and reproducible. • The obtained materials show superior catalytic activity in soot combustion. • The catalytic order is La{sub 0.9}Ag{sub 0.1}MnO{sub 3} > La{sub 0.9}Cu{sub 0.1}MnO{sub 3} > La{sub 0.9}Ca{sub 0.1}MnO{sub 3}. - Abstract: Fabrication of nanofibrous La{sub 0.9}A{sub 0.1}MnO{sub 3} (A = Ca, Cu, Ag) perovskite-type oxides with macroscopic shapes can be successfully obtained by using CNFs as templates. Field emission scanning electron microscopy (FE-SEM) and X-ray diffraction (XRD) analysis confirmed the template effect and formation of nanofibrous perovskite-type oxides on macroscopic silica fiber. It turned out that it is reliable to control the desired single-phase La{sub 0.9}A{sub 0.1}MnO{sub 3} (A = Ca, Cu, Ag) perovskite-type oxides formation by tuning the corresponding metal ratio during preparation process. Furthermore, it showed that the as-prepared nanofibrous La{sub 0.9}A{sub 0.1}MnO{sub 3} (A = Ca, Cu, Ag) perovskite-type oxides can greatly decrease the combustion temperature of nanosized carbon black particles, and follows the order of La{sub 0.9}Ag{sub 0.1}MnO{sub 3} > La{sub 0.9}Cu{sub 0.1}MnO{sub 3} > La{sub 0.9}Ca{sub 0.1}MnO{sub 3}, indicating their high potential application prospects in diesel soot particles treatment.

36 MATERIALS SCIENCE↗

Fabrication of nanofibrous A- or B-sites substituted LaCoO{sub 3} perovskites with macroscopic structures and their catalytic applications

Graphical abstract: Fabrication of nanofibrous La{sub 1−x}Ce{sub x}CoO{sub 3} (x = 0.05, 0.1, 0.2) and LaMn{sub x}Co{sub 1−x}O{sub 3} (x = 0.2, 0.5, 0.8) perovskite-type oxides with macroscopic structures can be successfully achieved by using carbon nanofibers (CNFs) as templates. Furthermore, their application for the combustion of carbon black (CB), which is a model of particulate matter exhausted from diesel engines, was demonstrated. - Highlights: • Nanofibrous perovskites with macroscopic shapes were successfully obtained. • CNFs template method used here is facile, effective and reproducible. • This method might be applicable to other novel material fabrication. • The obtained materials show superior catalytic activity in soot combustion. - Abstract: Fabrication of nanofibrous La{sub 1−x}Ce{sub x}CoO{sub 3} (x = 0.05, 0.1, 0.2) and LaMn{sub x}Co{sub 1−x}O{sub 3} (x = 0.2, 0.5, 0.8) perovskite-type oxides with macroscopic structures can be successfully achieved by using carbon nanofibers (CNFs) as templates. Field emission scanning electron microscopy (FE-SEM), coupled with X-ray diffraction (XRD) analysis confirmed the template effect and formation of the perovskite-type oxides on the macroscopic substrate. It turned out that this facile method can ensure the desired single-phase perovskite-type oxides formation by controlling the corresponding metal ratio during the preparation procedure. In addition, the immobilized nanofibrous La{sub 1−x}Ce{sub x}CoO{sub 3} (x = 0.05) and LaMn{sub x}Co{sub 1−x}O{sub 3} (x = 0.5) perovskite-type oxides can greatly decrease the combustion temperature of nanosized carbon black particles, which has the high potential application prospects in the treatment of diesel soot particles.

36 MATERIALS SCIENCE↗

Impact of coolant temperature on piston wall-wetting and smoke generation in a stratified-charge DISI engine operated on E30 fuel

A late-injection strategy is typically adopted in stratified-charge direct injection spark ignition (DISI) engines to improve combustion stability for lean operation, but this may induce wall wetting on the piston surface and result in high soot emissions. E30 fuel, i.e., gasoline with 30% ethanol, is a potential alternative fuel that can offer a high Research Octane Number. However, the relatively high ethanol content increases the heat of vaporization, potentially exacerbating wall-wetting issues in DISI engines. In this study, the Refractive Index Matching (RIM) technique is used to measure fuel wall films in the piston bowl. The RIM implementation uses a novel LED illumination, integrated in the piston assembly and providing side illumination of the piston-bowl window. This RIM diagnostics in combination with high-speed imaging was used to investigate the impact of coolant temperature on the characteristics of wall wetting and combustion in an optical DISI engine fueled with E30. The experiments reveal that the smoke emissions increase drastically from 0.068 FSN to 1.14 FSN when the coolant temperature is reduced from 90 °C to 45 °C. Consistent with this finding, natural flame luminosity imaging reveals elevated soot incandescence with a reduction of the coolant temperature, indicative of pool fires. Further, the RIM diagnostics show that a lower coolant temperature also leads to increased fuel film thickness, area, and volume, explaining the onset of pool fires and smoke.

42 ENGINEERING↗

A simplified CFD model for spectral radiative heat transfer in high-pressure hydrocarbon–air combustion systems

Detailed radiation modeling in piston engines has received relatively little attention to date. Recently, it is being revisited in light of current trends towards higher operating pressures and higher levels of exhaust-gas recirculation (EGR), both of which enhance molecular gas radiation. Advanced high-efficiency engines also are expected to function closer to the limits of stable operation, where even small perturbations to the energy balance can have a large influence on system behavior. Detailed radiation modeling using sophisticated tools like photon Monte Carlo/line-by-line (PMC/LBL) is computationally expensive. Here, guided by results from PMC/LBL, a simplified stepwise-gray spectral model in combination with a first-order spherical harmonics (P1 method) radiative transfer equation (RTE) solver is proposed and tested for engine-relevant conditions. Radiative emission, reabsorption and radiation reaching the walls are computed for a heavy-duty compression-ignition engine at part-load and full-load operating conditions with different levels of EGR and soot. The results are compared with those from PMC/LBL, P1/FSK (P1 with a full-spectrum k-distribution spectral model) and P1/Gray radiation models to assess the proposed model’s accuracy and computational cost. The results show that the proposed P1/StepwiseGray model can calculate reabsorption locally and globally with less than 10% error (with respect to PMC/LBL) at a small fraction of the computational cost of PMC/LBL (a factor of 30) and P1/FSK (a factor of 15). In contrast, error in computed reabsorption by the P1/Gray model is as high as 60%. Finally, it is expected that the simplified model should be broadly applicable to high-pressure hydrocarbon–air combustion systems, with or without soot.

42 ENGINEERING↗

Experimental and numerical investigation of ester droplet combustion: Application to butyl acetate

This paper presents an experimental and numerical study of the combustion of isolated n–butyl acetate droplets in the standard atmosphere. Numerical simulations are reported using a model that incorporates unsteady gas and liquid transport, variable properties, and radiation. Three skeletal mechanisms of n-butyl acetate, derived from a large detailed mechanism comprised of 819 species and 52,698 reactions, were used in the numerical simulations to evaluate the influence of the kinetic mechanism on burning. The reduced mechanisms comprised 212 species and 5413 reactions, 157 species and 3089 reactions, and 105 species and 1035 reactions. The numerical model did not include soot formation, though qualitatively mild sooting was noted only for droplets larger than 0.7 mm. The numerical predictions were in good agreement with experimental measurements of droplet and flame diameters. Flame extinction was numerically predicted which was attributed to a decrease of the characteristic diffusion time relative to the chemical time as droplet burned. Effects of initial droplet diameter on the evolution of maximum gas temperature (T max ) and peak mole fractions of CO 2 and CO are also examined numerically.

09 BIOMASS FUELS↗

Camphorane as a Renewable Diesel Blendstock Produced by Cyclodimerization of Myrcene

Camphorene was synthesized by the thermal Diels–Alder cyclodimerization of myrcene and subsequently hydrogenated to produce camphorane. On the basis of common fuel metrics (density, lower heating value, cetane, and viscosity) the prepared camphorane fuel exhibits appropriate physicochemical properties for its implementation in compression ignition engines. The high viscosity of camphorane necessitates its blending with petroleum diesel, which offers a final fuel within the ASTM specification for diesel. Soot production measurements of camphorane and its blends with diesel demonstrate a potential to significantly reduce soot emissions. The physicochemical and combustion properties of camphorane are further compared to those of other terpene biofuels along with biodiesel.

09 BIOMASS FUELS↗

Overcoming Variability: A Reproducible Approach to SERS Detection of Nanodiamonds

Detonation nanodiamonds (DNDs) are formed at specific pressures and temperatures during explosions. Different explosives produce varied yields of DNDs within their detonation soot, with Composition B producing the highest yield. Raman spectroscopy (RS) is often used for the characterization of sp 2 - and sp 3 -hybridized carbon allotropes in carbonaceous materials because of distinct disorder and graphitic bands. Bulk diamond also gives a distinct Raman peak at 1332 cm –1 . Furthermore, as bulk diamond decreases in size to nanometer-sized species, the peak red-shifts and broadens, becoming increasingly difficult to detect with RS using visible excitations. Therefore, surface-enhanced Raman spectroscopy (SERS) was used to enhance the diamond peak of DNDs, enabling better detection and faster examination of DNDs within detonation soot. Previous literature of the SERS of DNDs delivered inconsistent results in spectral signatures and SERS substrates. Herein, refining of the methodology for the acquisition of SERS spectra of DNDs was achieved. Before any SERS experiments, the DNDs were first characterized with normal Raman (NR) and scanning electron microscopy. Two routes for SERS enhancement were evaluated: colloidal noble metal nanoparticles and evaporated silver films. Silver films produced the best signal enhancement of DNDs with the best signal-to-noise and peak enhancements observed at 20–30 nm thick silver films at 5% (∼300 μW) laser power. Consistent, reproducible SERS spectra were acquired of small aggregates of DNDs down to ∼500 nm. NR and SERS mapping analysis of DNDs before and after evaporation of silver films revealed the improvements in the detection capabilities of SERS compared with NR.

Carbon↗

Synthesis of Butyl-Exchanged Polyoxymethylene Ethers as Renewable Diesel Blendstocks with Improved Fuel Properties

Methyl-terminated polyoxymethylene ethers (MM-POMEs), having the formula CH3O–(CH2O)n–CH3 (n = 3–5), are a high-cetane, low-sooting group of oxygenates that have recently attracted attention as potential diesel blendstocks. Despite these attractive fuel properties, MM-POMEs have shortcomings due to their low energy density and high water solubility. Guided by a computational fuel property assessment for POMEs with longer end-groups, the most promising improvements in the desired compression ignition fuel properties were observed for butyl-terminated POMEs. Here, an acid-catalyzed transacetalization reaction was developed to exchange the methyl end-groups of MM-POMEs (n = 3–6) with butyl end-groups. The reaction utilizes an ion-exchange resin as the acid catalyst at mild reaction conditions of 60 °C and atmospheric pressure. Approximately 100 mL of butyl-exchanged POMEs in the diesel boiling range were produced, enabling laboratory-scale fuel property testing. The butyl-terminated POME mixture possesses the advantaged fuel properties of the parent MM-POMEs (low-soot, high-cetane) while exhibiting improved energy density (lower heating value (LHV) of 30 MJ/kg) and substantially reduced water solubility (7.3 g/L) compared to the parent MM-POME mixture (LHV of 19 MJ/kg , water solubility of 258 g/L).

09 BIOMASS FUELS↗

Effects of Low-Carbon Energy Adoption on Airborne Particulate Matter Concentrations With Feedbacks to Future Climate Over California

California plans to reduce emissions of long-lived greenhouse gases (GHGs) through adoption of new energy systems that will also lower concentrations of short-lived absorbing soot contained in airborne particulate matter (PM). Here we examine the direct and indirect effects of reduced PM concentrations under a low-carbon energy (GHG-Step) scenario on radiative forcing in California. Simulations were carried out using the source-oriented WRF/Chem (SOWC) model with 12 km spatial resolution for the year 2054. Furthermore, the avoided aerosol emissions due to technology advances in the GHG-Step scenario reduce ground level PM concentrations by ~8.85% over land compared to the Business-as-Usual (BAU) scenario, but changes to meteorological parameters are more modest. Top-of-atmospheric forcing predicted by the SOWC model increased by 0.15 W m -2 , surface temperature warmed by 0.001 K, and planetary boundary layer height (PBLH) increased by 2.20 cm in the GHG-Step scenario compared to the BAU scenario. PM climate feedbacks are small because the significant changes in ground level PM concentrations associated with the GHG-Step scenario are limited to the first few hundred meters of the atmosphere, with little change for the majority of the vertical column above that level. As an order-of-magnitude comparison, the long-term effects of global reductions in GHG emissions (RCP8.5–RCP4.5) lowered average surface temperature over the California study domain by approximately 0.76 K. The effects of long-lived climate pollutants such as CO 2 are much stronger than the effects of short-lived climate pollutants such as PM soot over California in the year 2054.

54 ENVIRONMENTAL SCIENCES↗

Sediment Cores from White Pond, South Carolina, contain a Platinum Anomaly, Pyrogenic Carbon Peak, and Coprophilous Spore Decline at 12.8 ka

A widespread platinum (Pt) anomaly was recently documented in Greenland ice and 11 North American sedimentary sequences at the onset of the Younger Dryas (YD) event (~12,800calyr BP), consistent with the YD Impact Hypothesis. We report high-resolution analyses of a 1-meter section of a lake core from White Pond, South Carolina, USA. After developing a Bayesian age-depth model that brackets the late Pleistocene through early Holocene, we analyzed and quantifed the following: (1) Pt and palladium (Pd) abundance, (2) geochemistry of 58 elements, (3) coprophilous spores, (4) sedimentary organic matter (OC and sedaDNA), (5) stable isotopes of C (δ13C) and N (δ15N), (6) soot, (7) aciniform carbon, (8) cryptotephra, (9) mercury (Hg), and (10) magnetic susceptibility. We identifed large Pt and Pt/Pd anomalies within a 2-cm section dated to the YD onset (12,785±58calyr BP). These anomalies precede a decline in coprophilous spores and correlate with an abrupt peak in soot and C/OC ratios, indicative of large-scale regional biomass burning. We also observed a relatively large excursion in δ15N values, indicating rapid climatic and environmental/hydrological changes at the YD onset. Our results are consistent with the YD Impact Hypothesis and impact-related environmental and ecological changes.

54 ENVIRONMENTAL SCIENCES↗

Cleavage of an aromatic ring and radical migration

The present study undertakes a theoretical evaluation of thermal decomposition of aromatic-ring radicals. Potential energy surfaces and associated reaction rate coefficients were calculated for 1- and 2-naphthalenyl, acetanaphthylenyl, and pyrenyl radicals. Kinetic Monte-Carlo simulations were performed to examine the rates of ring cleavage in two sooting laminar premixed flames of ethylene. The simulations showed that the thermal aromatic-ring cleavage is comparable in rate to oxyradical decomposition in a heavier-sooting flame. The simulation also revealed, unexpectedly, fast internal ring radical migration, comparable in frequency to reaction events of aromatic growth.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Chemical imaging of individual stratospheric particles sampled over North America

The increasing size, severity, and frequency of wildfires have led to dramatic increases in particulate matter concentrations in the troposphere. Severe wildfires can generate intense convective systems capable of transporting large quantities of biomass burning organic aerosols (BBOA) to the upper troposphere and lower stratosphere (UTLS). Chemically complex organic matter and light-absorbing carbonaceous material is introduced into stratospheric regions that were historically isolated from direct surface emissions. In this study, stratospheric particles were sampled over North America during the Dynamics and Chemistry of the Summer Stratosphere (DCOTSS) campaign, an aircraft-based research project designed to characterize convective perturbation in the UTLS. Particle samples collected from six research flights during summer 2022 were analyzed using Computer-Controlled Scanning Electron Microscopy and Scanning Transmission X-ray Microscopy to investigate particle size distributions, morphology, chemical composition, and mixing state of stratospheric particles along transects across the continental United States and adjacent Pacific Ocean airspace. Analysis revealed that all sampled particles contained detectable levels of carbon, with most exhibiting organic volume fractions of 0.37 ± 0.20. Notably, about 5% of the particles also contained soot inclusions, which indicates the presence of refractory black carbon transported to stratospheric altitudes and provides direct evidence of wildfire-derived black carbon reaching the UTLS. Typical particle morphology exhibits organic shells over soot and inorganic cores and suggests secondary processing and aging of BBOA during transport to and within the UTLS. These findings provide compelling evidence that wildfire emissions play a critical role in affecting the long-term composition and radiative properties of stratospheric particles.

Sharpe, Steven [Purdue Univ., West Lafayette, IN (↗

Density functional theory study of the interaction of vinyl radical, ethyne, and ethene with benzene, aimed to define an affordable computational level to investigate stability trends in large van der Waals complexes

Our purpose is to identify a computational level sufficiently dependable and affordable to assess trends in the interaction of a variety of radical or closed shell unsaturated hydro-carbons A adsorbed on soot platelet models B. These systems, of environmental interest, would unavoidably have rather large sizes, thus prompting to explore in this paper the performances of relatively low-level computational methods and compare them with higher-level reference results. To this end, the interaction of three complexes between non-polar species, vinyl radical, ethyne, or ethene (A) with benzene (B) is studied, since these species, involved themselves in growth processes of polycyclic aromatic hydrocarbons (PAHs) and soot particles, are small enough to allow high-level reference calculations of the interaction energy ΔE{sub AB}. Counterpoise-corrected interaction energies ΔE{sub AB} are used at all stages. (1) Density Functional Theory (DFT) unconstrained optimizations of the A−B complexes are carried out, using the B3LYP-D, ωB97X-D, and M06-2X functionals, with six basis sets: 6-31G(d), 6-311 (2d,p), and 6-311++G(3df,3pd); aug-cc-pVDZ and aug-cc-pVTZ; N07T. (2) Then, unconstrained optimizations by Møller-Plesset second order Perturbation Theory (MP2), with each basis set, allow subsequent single point Coupled Cluster Singles Doubles and perturbative estimate of the Triples energy computations with the same basis sets [CCSD(T)//MP2]. (3) Based on an additivity assumption of (i) the estimated MP2 energy at the complete basis set limit [E{sub MP2/CBS}] and (ii) the higher-order correlation energy effects in passing from MP2 to CCSD(T) at the aug-cc-pVTZ basis set, ΔE{sub CC-MP}, a CCSD(T)/CBS estimate is obtained and taken as a computational energy reference. At DFT, variations in ΔE{sub AB} with basis set are not large for the title molecules, and the three functionals perform rather satisfactorily even with rather small basis sets [6-31G(d) and N07T], exhibiting deviation from the computational reference of less than 1 kcal mol{sup −1}. The zero-point vibrational energy corrected estimates Δ(E{sub AB}+ZPE), obtained with the three functionals and the 6-31G(d) and N07T basis sets, are compared with experimental D{sub 0} measures, when available. In particular, this comparison is finally extended to the naphthalene and coronene dimers and to three π−π associations of different PAHs (R, made by 10, 16, or 24 C atoms) and P (80 C atoms)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Predicting large-scale pool fire dynamics using an unsteady flamelet- and large-eddy simulation-based model suite

A low-Mach, unstructured, large-eddy-simulation-based, unsteady flamelet approach with a generalized heat loss combustion methodology (including soot generation and consumption mechanisms) is deployed to support a large-scale, quiescent, 5-m JP-8 pool fire validation study. The quiescent pool fire validation study deploys solution sensitivity procedures, i.e., the effect of mesh and time step refinement on capturing key fire dynamics such as fingering and puffing, as mesh resolutions approach O(1) cm. A novel design-order, discrete-ordinate-method discretization methodology is established by use of an analytical thermal/participating media radiation solution on both low-order hexahedral and tetrahedral mesh topologies in addition to quadratic hexahedral elements. Here, the coupling between heat losses and the flamelet thermochemical state is achieved by augmenting the unsteady flamelet equation set with a heat loss source term. Soot and radiation source terms are determined using flamelet approaches for the full range of heat losses experienced in fire applications including radiative extinction. The proposed modeling and simulation paradigm are validated using pool surface radiative heat flux, maximum centerline temperature location, and puffing frequency data, all of which are predicted within 10% accuracy. Simulations demonstrate that under-resolved meshes predict an overly conservative radiative heat flux magnitude with improved comparisons as compared to a previously deployed hybrid Reynolds-averaged Navier–Stokes/eddy dissipation concept-based methodology.

42 ENGINEERING↗

Slag monitoring system for combustion chambers of steam boilers

The computer-based boiler performance system presented in this article has been developed to provide a direct and quantitative assessment of furnace and convective surface cleanliness. Temperature, pressure, and flow measurements and gas analysis data are used to perform heat transfer analysis in the boiler furnace and evaporator. Power boiler efficiency is calculated using an indirect method. The on-line calculation of the exit flue gas temperature in a combustion chamber allows for an on-line heat flow rate determination, which is transferred to the boiler evaporator. Based on the energy balance for the boiler evaporator, the superheated steam mass flow rate is calculated taking into the account water flow rate in attemperators. Comparing the calculated and the measured superheated steam mass flow rate, the effectiveness of the combustion chamber water walls is determined in an on-line mode. Soot-blower sequencing can be optimized based on actual cleaning requirements rather than on fixed time cycles contributing to lowering of the medium usage in soot blowers and increasing of the water-wall lifetime.

20 FOSSIL-FUELED POWER PLANTS↗