Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SLURRIES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 991 records · Page 55

SALTSTONE PROCESSING FACILITY TRANSFER SAMPLE

On May 19, 2010, the Saltstone Production Facility inadvertently transferred 1800 gallons of untreated waste from the salt feed tank to Vault 4. During shut down, approximately 70 gallons of the material was left in the Saltstone hopper. A sample of the slurry in the hopper was sent to Savannah River National Laboratory (SRNL) to analyze the density, pH and the eight Resource Conservation and Recovery Act (RCRA) metals. The sample was hazardous for chromium, mercury and pH. The sample received from the Saltstone hopper was analyzed visually while obtaining sample aliquots and while the sample was allowed to settle. It was observed that the sample contains solids that settle in approximately 20 minutes (Figure 3-1). There is a floating layer on top of the supernate during settling and disperses when the sample is agitated (Figure 3-2). The untreated waste inadvertently transferred from the SFT to Vault 4 was toxic for chromium and mercury. In addition, the pH of the sample is at the regulatory limit. Visually inspecting the sample indicates solids present in the sample.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Sublimation Protection Coatings for Thermoelectric Materials for Space Power Applications

The compounds such as Yb14MnSb11 are relatively new p-type thermoelectric materials, respectively. NASA's interest in these material are to replace the state-of-the-art Si-Ge legs of the current radioisotope thermoelectric generators (RTGs). Ideally, the hot end of this leg would operate at 1000 degrees C in the vacuum of space. These materials, however, suffer from a high sublimation rate at elevated temperatures and would require a coating in order to survive the required RTG lifetime of 14 years. The purpose of present work is to develop sublimation protection coatings for Yb14MnSb11 at temperatures up to 1000 degrees C. Coatings for Yb14MnSb11 present many challenges. The coating must not significantly react or interdiffuse with the substrate thereby degrading the substrate or consuming the coating, must remain intact and not crack or spall during thermal cycling prior to launch, and must be a good insulator both electrically and thermally so as not to provide a short circuit for either electron flow or heat through the coating rather than through the leg. Based on these requirements, several oxides have been selected as possible coating candidates. This paper discusses the development of slurry processes to deposit these oxides coatings on thermoelectric materials.

Sublimation↗

Towards a fully printable battery : robocast deposition of separators.

The development of thin batteries has presented several interesting problems which are not seen in traditional battery sizes. As the size of a battery reaches a minimum, the usable capacity of the battery decreases due to the fact that the major constituent of the battery becomes the package and separator. As the size decreases, the volumetric contribution from the package and separator increases. This can result in a reduction of capacity from these types of batteries of nearly all of the available power. The development of a method for directly printing the battery layers, including the package, in place would help to alleviate this problem. The technology used in this paper to directly print battery components is known as robocasting and is capable of direct writing of slurries in complex geometries. This method is also capable of conformally printing on three dimensional surfaces, opening up the possibility of novel batteries based on tailoring battery footprints to conform to the available substrate geometry. Interfacial resistance can also be reduced by using the direct write method. Each layer is printed in place on the battery stack instead of being stacked one at a time. This ensures an intimate contact and seal at every interface within the cell. By limiting the resistance at these interfaces, we effectively help increase the useable capacity of our battery through increase transport capability. We have developed methodology for printing several different separator materials for use in a lithium cell. When combined with a printable cathode comprised of LiFePO{sub 4} (as seen in Figure 1) and a lithium anode, our battery is capable of delivering a theoretical capacity of 170 mAh g{sup -1}. This capacity is diminished by transport phenomena within the cell which limit the transport rate of the lithium ions during the discharge cycle. The material set chosen for the printable separator closely resemble those used in commercially available separators in order to keep the transport rates high within the cell during charge and discharge. In order to evaluate the effect of each layer being printed using the robocasting technique, coin cells using printed separator materials were assembled and cycled vs. Li/Li{sup +}. This allows for the standardization of a test procedure in order to evaluate each layer of a printed cell one layer at a time. A typical charge/discharge curve can be seen in Figure 2 using a printed LiFePO{sub 4} cathode and a printed separator with a commercial Celgard separator. This experiment was run to evaluate the loss in capacity and slowdown of transport within the cell due to the addition of the printed separator. This cell was cycled multiple times and showed a capacity of 75 mAh/g. The ability for this cell to cycle with good capacity indicates that a fully printable separator material is viable for use in a full lithium cell due to the retention of capacity. Most of the fully printed cathode and separator cells exhibit working capacities between 65 and 95 mAh/g up to this point. This capacity should increase as the efficiency of the printed separator increases. The ability to deposit each layer within the cell allows for intimate contact of each layer and ensures for a reduction of interfacial impedance of each layer within the cell. The overall effect of printing multiple layers within the cell will be an overall increase in the ionic conductivity during charge and discharge cycles. Several different polymer membranes have been investigated for use as a printed separator. The disadvantage of using polymer separators or solid electrolyte batteries is that they have relatively low conductivities at room temperature (10{sup -6} - 10{sup -8} S cm{sup -1}). This is orders of magnitude lower than the typically accepted 10{sup -3} S cm{sup -1} needed for proper ionic transport during battery discharge Because of their low conductivity, typical polymer separators such as polyethylene oxide (PEO) have a normal operational temperature well above ambient. At elevated temperature the conductivity of these polymers increases. These polymer membranes are, however, ideal for printable applications due to their ease of fabrication using the robocasting process and their ability to conform to surfaces uniformly. While the ability to print cathodes and separators is advantageous as a technology, several of the components still need to be fully optimized. The overall design for the full printed lithium cell can be seen in Figure 3. The printed cathode and separator will interface with a printed anode and current collector, using the LiFePO{sub 4} cycling to plate out a metallic lithium anode on the current collector during cycling. The ability to print every layer of the cell conformally using the robocasting technique will allow for ultimate flexibility in the application of a printed battery.

74 ATOMIC AND MOLECULAR PHYSICS↗

Donor-dependent Extent of Uranium Reduction for Bioremediation of Contaminated Sediment Microcosms

Bioremediation of uranium was investigated in microcosm experiments containing contaminated sediments from Oak Ridge, Tennessee to explore the importance of electron donor selection for uranium reduction rate and extent. In these experiments, all of the electron donors, including ethanol, glucose, methanol, and methanol with added humic acids, stimulated the reduction and immobilization of aqueous uranium by the indigenous microbial community. Uranium loss from solution began after the completion of nitrate reduction but essentially concurrent with sulfate reduction. When electron donor concentrations were normalized for their equivalent electron donor potential yield, the rates of uranium reduction were nearly equivalent for all treatments (0.55-0.95 {micro}mol L{sup -1} d{sup -1}). Uranium reduction with methanol proceeded after a 15-d longer lag time relative to that of ethanol or glucose. Significant differences were not found with the inclusion of humic acids. The extent of U reduction in sediment slurries measured by XANES at various time periods after the start of the experiment increased in the order of ethanol (5-7% reduced at 77 and 153 d), glucose (49% reduced at 53 d), and methanol (93% reduced at 90 d). The microbial diversity of ethanol- and methanol-amended microcosms in their late stage of U reduction was analyzed with 16S rRNA gene amplification. Members of the Geobacteraceae were found in all microcosms as well as other potential uranium-reducing organisms, such as Clostridium and Desulfosporosinus. The effectiveness of methanol relative to ethanol at reducing aqueous and sediment-hosted uranium suggests that bioremediation strategies that encourage fermentative poising of the subsurface to a lower redox potential may be more effective for long-term uranium immobilization as compared with selecting an electron donor that is efficiently metabolized by known uranium-reducing microorganisms.

10 SYNTHETIC FUELS↗

Commercial Submersible Mixing Pump For SRS Tank Waste Removal - 15223

The Savannah River Site Tank Farms have 45 active underground waste tanks used to store and process nuclear waste materials. There are 4 different tank types, ranging in capacity from 2839 m 3 to 4921 m 3 (750,000 to 1,300,000 gallons). Eighteen of the tanks are older style and do not meet all current federal standards for secondary containment. The older style tanks are the initial focus of waste removal efforts for tank closure and are referred to as closure tanks. Of the original 51 underground waste tanks, six of the original 24 older style tanks have completed waste removal and are filled with grout. The insoluble waste fraction that resides within most waste tanks at SRS requires vigorous agitation to suspend the solids within the waste liquid in order to transfer this material for eventual processing into glass filled canisters at the Defense Waste Processing Facility (DWPF). SRS suspends the solid waste by use of recirculating mixing pumps. Older style tanks generally have limited riser openings which will not support larger mixing pumps, since the riser access is typically 58.4 cm (23 inches) in diameter. Agitation for these tanks has been provided by four long shafted standard slurry pumps (SLP) powered by an above tank 112KW (150 HP) electric motor. The pump shaft is lubricated and cooled in a pressurized water column that is sealed from the surrounding waste in the tank. Closure of four waste tanks has been accomplished utilizing long shafted pump technology combined with heel removal using multiple technologies. Newer style waste tanks at SRS have larger riser openings, allowing the processing of waste solids to be accomplished with four large diameter SLPs equipped with 224KW (300 HP) motors. These tanks are used to process the waste from closure tanks for DWPF. In addition to the SLPs, a 224KW (300 HP) submersible mixer pump (SMP) has also been developed and deployed within older style tanks. The SMPs are product cooled and product lubricated canned motor pumps designed to fit within available risers and have significant agitation capabilities to suspend waste solids. Waste removal and closure of two tanks has been accomplished with agitation provided by 3 SMPs installed within the tanks. In 2012, a team was assembled to investigate alternative solids removal technologies to support waste removal for closing tanks. The goal of the team was to find a more cost effective approach that could be used to replace the current mixing pump technology. This team was unable to identify an alternative technology outside of mixing pumps to support waste agitation and removal from SRS waste tanks. However, the team did identify a potentially lower cost mixing pump compared to the baseline SLPs and SMPs. Rather than using the traditional procurement using an engineering specification, the team proposed to seek commercially available submersible mixer pumps (CSMP) as alternatives to SLPs and SMPs. SLPs and SMPs have a high procurement cost and the actual cost of moving pumps between tanks has shown to be significantly higher than the original estimates that justified the reuse of SMPs and SLPs. The team recommended procurement of “off-the-shelf” industry pumps which may be available for significant savings, but at an increased risk of failure and reduced operating life in the waste tank. The goal of the CSMP program is to obtain mixing pumps that could mix from bulk waste removal through tank closure and then be abandoned in place as part of tank closure. This paper will present the development, progress and relative advantages of the CSMP.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Final Scientific Report

Project 1: We have created a 3D optical research and design software platform for simulation and optimization, geared toward asymmetric, folded optical systems and new, enabling freeform surfaces. The software, Eikonal+, targets both institutional researchers and leading optical surface fabricators. With a modular design and the source code available to the development team at the University of Rochester, custom modules can be created for specific research interests and is accelerating the work on freeform optics currently being carried out at the Institute of Optics. With a research-based optical design environment, the fabrication, assembly, and testing industries can anticipate, innovate, and retool for the future of optical systems. Targeted proposals for science and innovation in freeform optics spanning design to fabrication, assembly, and testing can proceed with a level of technical transparency that has been unachievable in this field since the 1960’s, when optics design code was commercialized and became unavailable to the research community for competitive reasons. Project 2: The University of Rochester Laboratory for Laser Energetics (LLE) with personnel from Flint Creek Resources (FCR) collaborated to develop technologies for the reclamation and reuse of cerium oxide based slurries intended for the polishing of optical components. The pilot process was evaluated and modifications were made to improve the collection of spent glass polish, to improve the efficiency and capacity of the recycling equipment, and to expand the customer base. A portable, self-contained system was developed and fabricated to recycle glass polishing compounds where the spent materials are produced.

36 MATERIALS SCIENCE↗

Controlling the oriented growth of Ti{sub 2}SnC grains with carbon fiber as a reactive template in the Ti-Sn-C system

Carbon short fibers with a length of {approx}3 mm used as a reactive template were mixed with Ti and Sn powders. The mixture was pressurelessly sintered at 1200 deg. C for 2 h in a vacuum atmosphere. The microstructure shows that Ti{sub 2}SnC grains with a plate-like shape grow along a preferred direction, forming a 'string' structure in which Ti{sub 2}SnC platelets pack themselves closely with a top-bottom-top-bottom sequence. With increasing the length of the C fibers, the length of the 'string' structures increases. A large amount of long and aligned 'string' structures have formed after sintering the samples prepared by infiltration of the carbon short fibers with a length of {approx}50 mm in a Ti-Sn slurry and then stacking and cold pressing. X-ray diffraction and scanning electron microscopy, respectively were used to analyze and observe the phase composition and microstructure.

36 MATERIALS SCIENCE↗

Modeling analysis for grout hopper waste tank

The Saltstone facility at Savannah River Site (SRS) has a grout hopper tank to provide agitator stirring of the Saltstone feed materials. The tank has about 300 gallon capacity to provide a larger working volume for the grout nuclear waste slurry to be held in case of a process upset, and it is equipped with a mechanical agitator, which is intended to keep the grout in motion and agitated so that it won't start to set up. The primary objective of the work was to evaluate the flow performance for mechanical agitators to keep an adequate stirring of the feed materials and to estimate an agitator speed which provides acceptable flow performance with a 45 deg. pitched four-blade agitator. In addition, the power consumption required for the agitator operation was estimated. The modeling calculations were performed by taking two steps of the Computational Fluid Dynamics (CFD) modeling approach. A series of sensitivity calculations for different designs of agitators and operating conditions have been performed to investigate the impact of key parameters on the grout hydraulic performance in a 300-gallon hopper tank. Recommended operational guidance was developed by using the basic concept that local shear rates and flow patterns can be used as a measure of hydraulic performance and spatial stirring. Flow patterns and fluid residence time were estimated by a Lagrangian integration technique along the flow paths from the material feed inlet. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Determination of Radioisotope Content by Measurement of Waste Package Dose Rates - 13394

The objective of this communication is to report the observed correlation between the calculated air kerma rates produced by radioactive waste drums containing untreated ion-exchange resin and activated charcoal slurries with the measured radiation field of each package. Air kerma rates at different distances from the drum surface were calculated with the activity concentrations previously determined by gamma spectrometry of waste samples and the estimated mass, volume and geometry of solid and liquid phases of each waste package. The water content of each waste drum varies widely between different packages. Results will allow determining the total activity of wastes and are intended to complete the previous steps taken to characterize the radioisotope content of wastes packages. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Blending of Radioactive Salt Solutions in Million Gallon Tanks - 13002

Research was completed at Savannah River National Laboratory (SRNL) to investigate processes related to the blending of radioactive, liquid waste, salt solutions in 4920 cubic meter, 25.9 meter diameter storage tanks. One process was the blending of large salt solution batches (up to 1135 - 3028 cubic meters), using submerged centrifugal pumps. A second process was the disturbance of a settled layer of solids, or sludge, on the tank bottom. And a third investigated process was the settling rate of sludge solids if suspended into slurries by the blending pump. To investigate these processes, experiments, CFD models (computational fluid dynamics), and theory were applied. Experiments were performed using simulated, non-radioactive, salt solutions referred to as supernates, and a layer of settled solids referred to as sludge. Blending experiments were performed in a 2.44 meter diameter pilot scale tank, and flow rate measurements and settling tests were performed at both pilot scale and full scale. A summary of the research is presented here to demonstrate the adage that, 'One good experiment fixes a lot of good theory'. Experimental testing was required to benchmark CFD models, or the models would have been incorrectly used. In fact, CFD safety factors were established by this research to predict full-scale blending performance. CFD models were used to determine pump design requirements, predict blending times, and cut costs several million dollars by reducing the number of required blending pumps. This research contributed to DOE missions to permanently close the remaining 47 of 51 SRS waste storage tanks. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Removal of Historic Low-Level Radioactive Sediment from the Port Hope Harbour - 13314

At the Port Hope Harbour, located on the north shore of Lake Ontario, the presence of low-level radioactive sediment, resulting from a former radium and uranium refinery that operated alongside the Harbour, currently limits redevelopment and revitalization opportunities. These waste materials contain radium-226, uranium, arsenic and other contaminants. Several other on-land locations within the community of Port Hope are also affected by the low-level radioactive waste management practices of the past. The Port Hope Project is a community initiated undertaking that will result in the consolidation of an estimated 1.2 million cubic metres of the low-level radioactive waste from the various sites in Port Hope into a new engineered above ground long-term waste management facility. The remediation of the estimated 120,000 m{sup 3} of contaminated sediments from the Port Hope Harbour is one of the more challenging components of the Port Hope Project. Following a thorough review of various options, the proposed method of contaminated sediment removal is by dredging. The sediment from the dredge will then be pumped as a sediment-water slurry mixture into geo-synthetic containment tubes for dewatering. Due to the hard substrate below the contaminated sediment, the challenge has been to set performance standards in terms of low residual surface concentrations that are attainable in an operationally efficient manner. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

A practical solution to Hanford's tank waste problem

The main characteristics of the Hanford radwaste are: -) it is extremely dilute and generates little heat, -) it is comprised of materials incompatible with high loading in borosilicate glass, and -) it is already situated at a good geological repository site. We propose that Hanford's radwaste should be homogenized (not separated), converted to an iron phosphate (Fe-P) glass 'aggregate' (marbles, gems, or cullet), that is then slurried up with a cementitious grout and pumped into Hanford's 'best preserved' tanks for disposal. This proposal is efficient, safe and cheap.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Production of LEU fully ceramic microencapsulated fuel for irradiation testing

The Advanced Fuels Campaign of the US DOE Fuel Cycle Research/Development program is currently engaged in production of FCM fuel for irradiation testing in the Advanced Test Reactor (ATR) at Idaho National Laboratory (INL). FCM fuel production is a serial process with 3 major steps namely kernel, TRISO, and compact production. The first step in the kernel process is production of air-dried UO{sub 3} gel spheres with suspended carbon particles. These spheres, roughly 2 mm in size, are then calcined to produce a mixture of UO{sub 2} and carbon. This calcination step may be performed in either argon, hydrogen, or mixtures of these gases. Once the calcination step is complete, temperature is increased (>1400 Celsius degrees) to convert this mixture to UO{sub 2} + UC{sub x}. Once dense oxide-carbide kernels are available, the inert environment is switched to a nitrogen containing one to facilitate carbothermic reduction of kernels and production of UN. Essentially, the oxygen and carbon in the oxide-carbide kernels react with one another to produce CO and are replaced with nitrogen inside the lattice. The TRISO step in fuel production is incorporation of a porous carbon buffer layer, a dense inner pyrolytic carbon layer (IPyC), a SiC layer, and finally and outer pyrolytic carbon layer (OPyC) onto the UN kernels. The coating layer deposition step is carried out inside a graphite furnace using a fluidized bed chemical vapor deposition (CVD) process. In essence, a mixture of reactant and inert gasses flow from the bottom through a bed of particles that are in turn fluidized by the gas stream. The particles undergo CVD and once a different coating layer is to be incorporated, the furnace temperature is adjusted and the reactant gases are changed. The final step in the series of fuel production activities is the consolidation of UN TRISO particles inside the SiC matrix to produce cylindrical pellets. It entails 3 critical areas: SiC powder mixing, over-coating of particles, and high-temperature densification. Optimal execution of the powder mixing step is vital to achieve a fully dense SiC matrix at the end of the process. The SiC matrix is consolidated using a special form of liquid phase sintering (LPS) involving nano-powder feedstock that is designated as the NITE process. The SiC nano-powder slurry is sprayed directly onto the particle surface using a piezoelectric nozzle. Once the over-coated particles are available, final consolidation step at high temperatures (1875 Celsius degrees) is carried out.

36 MATERIALS SCIENCE↗

Development of a nuclear mixing process for high performance cementation - 15064

In the CEA Project 'Cementation of LLW/ILW Slurry' EIRICH and CEA developed together a high performance mixing process matching the French security regulations for nuclear facilities. Since 2010 mixing tests had been carried out by CEA to develop and verify a new cementation process. In 2012 EIRICH started the development of the mixing equipment for the cementation plant together with CEA. This new cementation plant will be put into operation in 2016 at the CEA site in Marcoule. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Cold-cap temperature profile comparison between the laboratory and mathematical model - 15591

The rate of waste vitrification in an electric melter is connected to the feed-to-glass conversion process, which occurs in the cold cap, a layer of reacting feed on top of molten glass. The cold cap consists of two layers: a low-temperature (∼100 deg. C - ∼800 deg. C) region of unconnected, reacting feed and a high-temperature (∼800 deg. C - ∼1100 deg. C) region of molten glass with gas bubbles and cavities. A recently developed mathematical model describes the effect of the cold cap on glass production. For verification of the mathematical model, a cold cap produced in a laboratory-scale melter was subsequently analyzed by correlating structural features of a polished region with those obtained in heat-treated feed samples to determine the temperature profile as a function of cold-cap position. After corrections were made for the diminished volume of bubbles and collapsed cavities that occurred in the cold-cap sample during cooling, the temperature gradients were alike in the model and the laboratory cold cap through the range from ∼500 deg. C to ∼1100 deg. C. The temperature profiles were different in the upper region of the cold cap because the radiant heat from the molten glass in the laboratory-scale melter resulted in dry and hot (∼400 deg. C) surface conditions whereas the model assumed a surface covered by boiling slurry. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗