SEARCH · Engineering Papers

Results for “RESIDUES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 991 records · Page 55

All sources NASA NTRS DOE OSTI

NASA NTRS1993

Method and apparatus for determination of material residual stress

A device for the determination of residual stress in a material sample consisting of a sensor coil, adjacent to the material sample, whose resistance varies according to the amount of stress within the material sample, a mechanical push-pull machine for imparting a gradually increasing compressional and tensional force on the material sample, and an impedance gain/phase analyzer and personal computer (PC) for sending an input signal to and receiving an input signal from the sensor coil is presented. The PC will measure and record the change in resistance of the sensor coil and the corresponding amount of strain of the sample. The PC will then determine, from the measurements of change of resistance and corresponding strain of the sample, the point at which the resistance of the sensor coil is at a minimum and the corresponding value and type of strain of the sample at that minimum resistance point, thereby, enabling a calculation of the residual stress in the sample.

Chern, Engmin J.↗

NASA NTRS1993

Scanning electron microscope/energy dispersive x ray analysis of impact residues in LDEF tray clamps

Detailed optical scanning of tray clamps is being conducted in the Facility for the Optical Inspection of Large Surfaces at JSC to locate and document impacts as small as 40 microns in diameter. Residues from selected impacts are then being characterized by Scanning Electron Microscopy/Energy Dispersive X-ray Analysis at CNES. Results from this analysis will be the initial step to classifying projectile residues into specific sources.

Bernhard, Ronald P.↗

NASA NTRS1993

Surface roughness due to residual ice in the use of low power deicing systems

Thicknesses of residual ice are presented to provide information on surface contamination and associated roughness during deicing events. Data was obtained from low power ice protection systems tests conducted in the Icing Research Tunnel at NASA Lewis Research Center (LeRC) with nine different deicing systems. Results show that roughness associated with residual ice is not characterized by uniformly distributed roughness. Results also show that deicing systems require a critical mass of ice to generate a sufficient expelling force to remove the ice.

Shin, Jaiwon↗

NASA NTRS1992

An extension of command shaping methods for controlling residual vibration using frequency sampling

The authors present an extension to the impulse shaping technique for commanding machines to move with reduced residual vibration. The extension, called frequency sampling, is a method for generating constraints that are used to obtain shaping sequences which minimize residual vibration in systems such as robots whose resonant frequencies change during motion. The authors present a review of impulse shaping methods, a development of the proposed extension, and a comparison of results of tests conducted on a simple model of the space shuttle robot arm. Frequency shaping provides a method for minimizing the impulse sequence duration required to give the desired insensitivity.

Singer, Neil C.↗

NASA NTRS1993

Residual strain gradient determination in metal matrix composites by synchrotron X-ray energy dispersive diffraction

An X-ray technique for the measurement of internal residual strain gradients near the continuous reinforcements of metal matrix composites has been investigated. The technique utilizes high intensity white X-ray radiation from a synchrotron radiation source to obtain energy spectra from small (0.001 cu mm) volumes deep within composite samples. The viability of the technique was tested using a model system with 800 micron Al203 fibers and a commercial purity titanium matrix. Good agreement was observed between the measured residual radial and hoop strain gradients and those estimated from a simple elastic concentric cylinders model. The technique was then used to assess the strains near (SCS-6) silicon carbide fibers in a Ti-14Al-21Nb matrix after consolidation processing. Reasonable agreement between measured and calculated strains was seen provided the probe volume was located 50 microns or more from the fiber/matrix interface.

Kuntz, Todd A.↗

NASA NTRS1992

Nonenzymatic template-directed synthesis on hairpin oligonucleotides. II - Templates containing cytidine and guanosine residues

Hairpin oligonucleotides were prepared with 5-prime-terminal single-stranded sequments containing cytidylate (C) and guanylate (G) residues. It was found that incubation of these hairpin oligonucleotides with a mixutre of cytidine and guanosine 5-prime-phosphoro (2-methyl)imidazolides results in sequence-specific addition of C and G residues to the 3-prime terminus of the hairpin.

Wu, Taifeng↗

NASA NTRS1993

Estimates of the stratospheric residual circulation using the downward control principle

The transformed Eulerian-mean momentum and continuity equations are used to calculate the residual mean meridional circulations for the lower stratosphere and troposphere. Momentum and temperature fluxes required for the computation are estimated from U.K. Meteorological Office (UKMO) analyzed geopotential heights. National Center for Atmospheric Research (NCAR) CCM2 model output is used to assess the errors associated with the calculation. The model comparisons showed that the method works reasonably well for solstice seasons, but is inadequate for equinox seasons. In addition, it is found that some parameterization of gravity wave drag needs to be included with the planetary wave forcing to accurately estimate the residual mean circulation using this method.

Rosenlof, Karen H.↗

NASA NTRS1993

Estimation of Kalman filter gain from output residuals

This paper presents a procedure to estimate the Kalman filter gain from input-output measurement data with a given system model. The system model can be a finite element model or an experimental model from any identification method. The procedure consists of three basic steps. First, the stochastic portion related to the residuals of the response is computed. Second, the coefficients of a linear difference model for the stochastic portion are estimated by a least-squares solution that minimizes the filter residual. Third, the Kalman filter gain is computed from these model coefficients. Experimental results are presented to illustrate the usefulness of the developed procedure.

Juang, Jer-Nan↗

NASA NTRS1992

The effect of fiber microstructure on evolution of residual stresses in silicon carbide/titanium aluminide composites

This paper examines the effect of the morphology of the SCS6 silicon carbide fiber on the evolution of residual stresses in SiC/Ti composites. A micromechanics model based on the concentric cylinder concept is presented which is used to calculate residual stresses in a SiC/Ti composite during axisymmetric cooling by a spatially uniform temperature change. The silicon carbide fiber is modeled as a layered material with five distinct transversely isotropic and orthotropic, elastic layers, whereas the titanium matrix is taken to be isotropic, with temperature-dependent elastoplastic properties. The results arc compared with those obtained based on the assumption that the silicon carbide fiber is isotropic and homogeneous.

Pindera, Marek-Jerzy↗

NASA NTRS1992

Scanning electron acoustic microscopy of residual stresses in ceramics - Theory and experiment

The paper presents a three-dimensional mathematical model of signal generation and contrast in brittle materials and uses the model to simulate the effect of residual stress fields on the scanning electron acoustic microscopy (SEAM)-generated electron acoustic signal. According to the model, a positive (tensile) strain produces an increase in the output signal, whereas a negative (compressive) strain produces a decrease in the ouput signal. Dark field contrast conditions occur at a chopping frequency at which V2 - V1 is greater than 0 (where V2 = V is the SEAM output in a region of residual stresses, and V1 is the output in a stress-free region of the sample). Under ideal conditions (maximum contrast) V1 approaches zero. It was found that tensile strains of the order 0.2-0.3 percent, possible in brittle materials, would produce a variation of the acoustic output signal of the order 10 nV (about 1 percent), well within the image contrast and signal processing capability of the SEAM electronics.

Cantrell, John H.↗

NASA NTRS1941

Relief of Residual Stress in Streamline Tie Rods by Heat Treatment

About two-thirds of the residual stress in cold-worked SAE 1050 steel tie rods was relieved by heating 30 minutes at 600 degrees Fahrenheit. Cold-worked austenitic stainless-steel tie rods could be heated at temperatures up to 1000 degrees Fahrenheit without lowering the important physical properties. The corrosion resistance, in laboratory corrosion test, of straight 18:8 and titanium-treated 18:8 materials appeared to be impaired after heating at temperatures above 800 degrees or 900 degrees fahrenheit. Columbium-treated and molybdenum-treated 18:8 steel exhibited improved stability over a wide range of temperatures. Tie rods of either material could be heated 30 minutes with safety at any temperature up to 1000 degrees Fahrenheit. At this temperature most of the residual stress would be relieved.

Pollard, R E↗

NASA NTRS1993

Low-latency digital frequency synthesizer using the residue number system

A low-latency frequency synthesizer using the Direct Digital Synthesis (DDS) technique has been designed. Called the Residue Assisted Frequency Synthesizer (RAFS), it exhibits frequency switching times which are reduced by more than 50 percent below previously published designs. The switching speed advantage is made possible by the use of the Residue Number System, which allows the pipeline lengths in the Phase Accumulator and other circuitry to be reduced significantly.

Chren, William A., Jr.↗

NASA NTRS1994

Stochastic model of the residual acceleration environment in microgravity

We describe a theoretical investigation of the effects that stochastic residual accelerations (g-jitter) onboard spacecraft can have on experiments conducted in a microgravity environment. We first introduce a stochastic model of the residual acceleration field, and develop a numerical algorithm to solve the equations governing fluid flow that allow for a stochastic body force. We next summarize our studies of two generic situations: stochastic parametric resonance and the onset of convective flow induced by a fluctuating acceleration field.

Vinals, Jorge↗

NASA NTRS1995

Estimates of effects of residual acceleration on USML-1 experiments

The purpose of this study effort was to develop analytical models to describe the effects of residual accelerations on the experiments to be carried on the first U.S. Microgravity Lab mission (USML-1) and to test the accuracy of these models by comparing the pre-flight predicted effects with the post-flight measured effects. After surveying the experiments to be performed on USML-1, it became evident that the anticipated residual accelerations during the USML-1 mission were well below the threshold for most of the primary experiments and all of the secondary (Glovebox) experiments and that the only set of experiments that could provide quantifiable effects, and thus provide a definitive test of the analytical models, were the three melt growth experiments using the Bridgman-Stockbarger type Crystal Growth Furnace (CGF). This class of experiments is by far the most sensitive to low level quasi-steady accelerations that are unavoidable on space craft operating in low earth orbit. Because of this, they have been the drivers for the acceleration requirements imposed on the Space Station. Therefore, it is appropriate that the models on which these requirements are based are tested experimentally. Also, since solidification proceeds directionally over a long period of time, the solidified ingot provides a more or less continuous record of the effects from acceleration disturbances.

Naumann, Robert J.↗

NASA NTRS1995

Seasonal cycle of the residual mean meridional circulation in the stratosphere

The transformed Eurlerian-mean (TEM) residual circulation is used to study the zonally averaged transport of mass in the stratosphere. The residual circulation is estimated from heating rates computed with a radiative transfer model using data from the Upper Atmosphere Research Satellite (UARS) as inputs. An annual cycle exists in the resulting circulation in the lower stratosphere, with a larger net upward mass flux across a pressure surface in the tropics during northern hemisphere winter than during northern hemisphere summer. The annual cycle in upward tropical mass flux follows the annual cycle in downward mass flux across a pressure surface in the northern hemisphere extratropics. It is argued that the annual cycle in zonal momentum forcing in the northern hemisphere stratosphere is controlling mass flux across a pressure surface in the lower stratosphere both in the tropics and in the northern hemisphere extratropics.

Rosenlof, Karen H.↗

NASA NTRS1992

Scanning electron acoustic microscopy of residual stresses in ceramics: Theory and experiment

Several reviews have highlighted a number of applications of scanning electron acoustic microscopy (SEAM) to metals and semiconductors which show that SEAM can provide new information on surface and near-surface features of such materials, but there have been few studies attempting to determine the capabilities of SEAM for characterizing ceramic materials. We have recently observed image contrast in SEAM from residual stress fields induced in brittle materials by Vickers indentations that is strongly dependent on the electron beam chopping frequency. We have also recently developed a three-dimensional mathematical model of signal generation and contrast in SEAM, appropriate to the brittle materials studied, that we use as a starting point in this paper for modeling the effect of residual stress fields on the generated electron acoustic signal. The influence of the electron beam chopping frequency is also considered under restrictive assumptions.

Cantrell, John H.↗

NASA NTRS1996

Neutron diffraction measurements and modeling of residual strains in metal matrix composites

Neutron diffraction measurements at room temperature are used to characterize the residual strains in tungsten fiber-reinforced copper matrix, tungsten fiber-reinforced Kanthal matrix, and diamond particulate-reinforced copper matrix composites. Results of finite element modeling are compared with the neutron diffraction data. In tungsten/Kanthal composites, the fibers are in compression, the matrix is in tension, and the thermal residual strains are a strong function of the volume fraction of fibers. In copper matrix composites, the matrix is in tension and the stresses are independent of the volume fraction of tungsten fibers or diamond particles and the assumed stress free temperature because of the low yield strength of the matrix phase.

Saigal, A.↗

NASA NTRS1996

Analysis of Residual Acceleration Effects on Transport and Segregation During Directional Solidification of Tin-Bismuth in the MEPHISTO Furnace Facility

The object of this work, started in March of 1995, is to approach the problem of determining the transport conditions (and effects of residual acceleration) during the plane-front directional solidification of a tin-bismuth alloy under low gravity conditions. The work involves using a combination of 2- and 3-D numerical models, scaling analyses, 1-D models and the results of ground-based and low-gravity experiments. The experiments conducted in the MEPHISTO furnace facility during the USMP-3 spaceflight which took place earlier this year (22 Feb. - 6 Mar. 1996). This experiment represents an unprecedented opportunity to make a quantitative correlation between residual accelerations and the response of an actual experimental solidification system

Alexander, J. Iwan D.↗