A method for predicting the performance of high reaction supersonic compressor blade sections.
Supersonic compressor blade sections performance prediction near maximum pressure ratio and efficiency by analyzing flow processes
Boxer, E.↗
SEARCH · Engineering Papers
Results for “Performance Ratio”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
An adaptive narrow band frequency modulation voice communication system
A narrow band frequency modulation communication system is described which provides for the reception of good quality voice at low carrier-to-noise ratios. The high level of performance is obtained by designing a limiter and phase lock loop combination as a demodulator, so that the bandwidth of the phase lock loop decreases as the carrier level decreases. The system was built for the position location and aircraft communication equipment experiment of the ATS 6 program.
Wishna, S.↗
Wind tunnel investigation of effects of variations in Reynolds number and leading-edge treatment on the aerodynamic characteristics of an externally blown jet-flap configuration
An investigation has been conducted in a full-scale tunnel to determine the effects of variations in Reynolds number and leading-edge treatment on the aerodynamic characteristics of an externally blown jet-flap transport configuration. The model had a double-slotted trailing-edge flap and was powered by four high-bypass-ratio turbofan engines. Tests were performed by using each of three leading-edge devices (a 30-percent-chord flap and 15- and 25-percent-chord slats) at Reynolds numbers from 0.47 x one million to 1.36 x one million thrust coefficients up to 3.5. The use of a 25-percent-chord slat was found to be more effective than a 15-percent-chord slat or a 30-percent-chord flap in extending the stall angle of attack and in minimizing the loss of lift after the stall. The large slat was also effective in reducing the rolling moments that occurred when the engine-out wing stalled first.
Parlett, L. P.↗
Aeroacoustic performance of scale model sonic inlets
A low speed wind tunnel was used to evaluate the inflight aeroacoustic performance of several single- and multiple-passage sonic inlets. Takeoff and approach geometries were tested, and the effects of inlet lip and diffuser design were determined. Results indicate that the single passage geometries, in particular a cylindrical centerbody takeoff geometry and a bulb shaped centerbody approach geometry, provide the highest level of aeroacoustic performance. Increasing inlet lip contraction ratio extends the maximum incidence angle for attached lip flow, while increasing inlet diffuser length results in higher total pressure recovery for a given amount of noise suppression.
Abbott, J. M.↗
High-efficiency solar concentrator
A new type of solar concentrator is presented using liquid lenses and simple translational tracking mechanism. The concentrator achieves a 100:1 nominal concentration ratio and is compared in performance with a flat-plate collector having two sheets of glazing and non-selective coating. The results of the thermal analysis show that higher temperatures can be obtained with the concentrator than is possible with the non-concentrator flat-plate type. Furthermore, the thermal efficiency far exceeds that of the comparative flat-plate type for all operating conditions.
Lansing, F. L.↗
Performance correlations of five solar collectors tested simultaneously outdoors
Collector thermal efficiency, and efficiency degradation with time were measured for 5 flat-plate solar collectors tested simultaneously in an outdoor solar collector test facility. Results indicate that by using collector performance parameters which account for diffuse isolation, outdoor data recorded on cloud days can be used as a measure of performance, as long as the ratio of direct to total insolation exceeds approximately 0.6. These outdoor results also show good agreement with thermal efficiency data obtained indoors in a solar simulator. Significant efficiency degradation occurred on only one of the five collectors exposed to outdoor conditions for a period of one to two years.
Miller, D. R.↗
A review of advanced rotor research
This paper reviews advanced-rotor concepts including the advancing blade concept, the circulation control rotor, the X-wing rotor, the variable diameter rotor, the hingeless tilt rotor, the bearingless main rotor, the composite structures rotor, the variable geometry rotor, the multicyclic controllable pitch rotor, the multicyclic controllable twist rotor, and the live twist rotor. The rotor concepts are discussed in terms of performance (cruise speed, and lift/drag ratio) and dynamic loads and vibration.
Kelly, M. W.↗
Development of a prototype regenerable carbon dioxide absorber for portable life support systems
The design and development of a prototype carbon dioxide absorber using potassium carbonate (K2CO3) is described. Absorbers are constructed of thin, porous sheets of supported K2CO3 that are spirally wound to form a cylindrical reactor. Axial gas passages are formed between the porous sheets by corrugated screen material. Carbon dioxide and water in an enclosed life support system atmosphere react with potassium carbonate to form potassium bicarbonate. The potassium carbonate is regenerated by heating the potassium bicarbonate to 150 C at ambient pressure. The extravehicular mission design conditions are for one man for 8 h. Results are shown for a subunit test module investigating the effects of heat release, length-to-diameter ratio, and active cooling upon performance. The most important effect upon carbon dioxide removal is the temperature of the potassium carbonate.
Onischak, M.↗
Performance correlations of five solar collectors tested simultaneously outdoors
Collector thermal efficiency, and efficiency degradation with time were measured for 5 flat-plate solar collectors tested simultaneously in an outdoor solar collector test facility. Results indicate that by using collector performance parameters which account for diffuse insolation, outdoor data recorded on 'cloudy' days can be used as a measure of performance, as long as the ratio of direct to total insolation exceeds approximately 0.6. These outdoor results also show good agreement with thermal efficiency data obtained indoors in a solar simulator. Significant efficiency degradation occurred on only one of the five collectors exposed to outdoor conditions for a period of one to two years.
Miller, D. R.↗
The practical impact of elastohydrodynamic lubrication
The use of elastohydrodynamics in the analysis of rolling element bearings is discussed. Relationships for minimum film thickness and tractive force were incorporated into computer codes and used for bearing performance prediction. The lambda parameter (ratio of film thickness to composite surface roughness) was shown to be important in predicting bearing life and failure mode. Results indicate that at values of lambda below 3 failure modes other than the classic subsurface initiated fatigue can occur.
Anderson, W. J.↗
Preliminary QCSEE program - Test results
Preliminary results are reported for the Quiet Clean Short-haul Experimental Engine (QCSEE) program initiated by NASA in 1974 to develop propulsion system technology suitable for powered-lift short-range commercial aircraft. The QCSEE technology also has applications to the proposed U.S. Navy V/STOL aircraft. Emphasis in the QCSEE program is placed on developing engines with low noise characteristics; in addition, the power plants are required to conform to EPA 1979 pollutant emissions standards. Thrust performance, fan design, and thrust/weight ratio are discussed for both the over-the-wing and under-the-wing engine configurations under study.
Ciepluch, C. C.↗
On the rational design of compressible flow ejectors
A fluid mechanics review of chemical laser ejectors is presented. The characteristics of ejectors with single and multiple driver nozzles are discussed. Methods to compute an optimized performance map in which secondary Mach number and performance are computed versus mass ratio, to compute the flow distortion at each optimized condition, and to determine the thrust area for the design point to match diffuser impedence are examined.
Ortwerth, P. J.↗
High-efficiency solar concentrator
A new type of solar concentrator is presented using liquid lenses and simple translational tracking mechanism. The concentrator achieves a 100:1 nominal concentration ratio and is compared in performance with a flat-plate collector having two sheets of glazing and non-selective coating. The results of the thermal analysis show that higher temperatures can be obtained with the concentrator than is possible with the non-concentrator flat-plate type. Furthermore, the thermal efficiency far exceeds that of the comparative flat-plate type for all operating conditions.
Lansing, F. L.↗
Development of a preprototype Sabatier CO2 reduction subsystem
A lightweight, quick starting reactor utilizes a highly active and physically durable methanation catalyst composed of ruthenium on alumina. The use of this improved catalyst permits a single straight through plug flow design with an average lean component H2/CO2 conversion efficiency of over 99% over a range of H2/CO2 molar ratios of 1.8 to 5 while operating with flows equivalent to a crew size of one person steadystate to 3 persons cyclical. The reactor requires no heater operation after start-up even during simulated 55 minute lightside/39 minute darkside orbital operation over the above range of molar ratios and crew loadings. Subsystem performance was proven by parametric testing and endurance testing over a wide range of crew sizes and metabolic loadings. The subsystem's operation and performance is controlled by a microprocessor and displayed on a nineteen inch multi-colored cathode ray tube.
Kleiner, G. N.↗
Design optimization of sinusoidal glass honeycomb for flat plate solar collectors
The design of honeycomb made of sinusoidally corrugated glass strips was optimized for use in water-cooled, single-glazed flat plate solar collectors with non-selective black absorbers. Cell diameter (d), cell height (L), and pitch/diameter ratio (P/d) maximizing solar collector performance and cost effectiveness for given cell wall thickness (t sub w) and optical properties of glass were determined from radiative and convective honeycomb characteristics and collector performance all calculated with experimentally validated algorithms. Relative lifetime values were estimated from present materials costs and postulated production methods for corrugated glass honeycomb cover assemblies. A honeycomb with P/d = 1.05, d = 17.4 mm, L = 146 mm and t sub w = 0.15 mm would provide near-optimal performance over the range delta T sub C greater than or equal to 0 C and less than or equal to 80 C and be superior in performance and cost effectiveness to a non-honeycomb collector with a 0.92/0.12 selective black absorber.
Mcmurrin, J. C.↗
Computer modeling of fan-exit-splitter spacing effects on F100 response to distortion
The distortion response of the F100(3) engine was effected by the fan exit splitter configuration. The sensitivity for a proximate splitter fan is calculated to be slightly greater than a remote splitter configuration with identical airfoils. Predicted response was based upon a multiple segment parallel compressor Model modified to include a bypass ratio representation that effects the performance characteristics of the last rotor and intermediate case struts. The predicted distortion response required an accurate definition of row pre- and post-stall undistorted operation.
Shaw, M.↗
Comparison between variable and fixed dwell-time PN acquisition algorithms
Pseudo noise (PN) spread spectrum systems require a very accurate alignment between the PN code epochs at the transmitter and receiver. This synchronism is typically established through a two-step algorithm, including a coarse synchronization procedure and a fine synchronization procedure. A standard approach for the coarse synchronization is a sequential search over all code phases. The measurement of the power in the filtered signal is used to either accept or reject the code phase under test as the phase of the received PN code. This acquisition strategy, called a single dwell-time system, has been analyzed by Holmes and Chen (1977). A synopsis of the field of sequential analysis as it applies to the PN acquisition problem is provided. From this, the implementation of the variable dwell time algorithm as a sequential probability ratio test is developed. The performance of this algorithm is compared to the optimum detection algorithm and to the fixed dwell-time system.
Braun, W. R.↗
Symbol Stream Combining Versus Baseband Combining for Telemetry Arraying
The objectives of this article are to investigate and analyze the problem of combining symbol streams from many Deep Space Network stations to enhance bit signal-to-noise ratio and to compare the performance of this combining technique with baseband combining. Symbol stream combining (SSC) has some advantages and some disadvantages over baseband combining (BBC). The SSC suffers almost no loss in combining the digital data and no loss due to the transmission of the digital data by microwave links between the stations. The BBC suffers 0.2 dB loss due to alignment and combining the IF signals and 0.2 dB loss due to transmission of signals by microwave links. On the other hand, the losses in the subcarrier demodulation assembly (SDA) and in the symbol synchronization assembly (SSA) for SSC are more than the losses in the SDA and SSA for BBC. It is shown that SSC outperforms BBC by about 0.35 dB (in terms of the required bit energy-to-noise spectral density for a bit error rate of 1,000) for an array of three DSN antennas, namely 64 m, 34m(T/R) and 34m(R).
Divsalar, D.↗