Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Parallel application”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 991 records · Page 55
All sourcesNASA NTRSDOE OSTI
NASA NTRS1997

Microfabricated Ice-Detection Sensor

Knowledge of ice conditions on important aircraft lift and control surfaces is critical for safe operation. These conditions can be determined with conventional ice-detection sensors, but these sensors are often expensive, require elaborate installation procedures, and interrupt the airflow. A micromachined, silicon-based, flush-mounted sensor which generates no internal heat has been designed, batch fabricated, packaged, and tested. The sensor is capable of distinguishing between an ice-covered and a clean surface. It employs a bulk micromachined wafer with a 7 micrometer-thick, boron-doped, silicon diaphragm which serves as one plate of a parallel-plate capacitor. This is bonded to a second silicon wafer which contains the fixed electrodes, one to drive the diaphragm by application of a voltage, the other to measure the deflection by a change in capacitance. The diaphragm sizes ranged from 1x1 mm to 3x3 mm, and the gap between parallel-plate capacitors is 2 micrometers. A 200 V d.c. was applied to the driving electrode which caused the capacitance to increase approximately 0.6pf, from a nominal capacitance of 0.6pf, when the surface was ice free. After the sensor was cooled below the freezing point of water, the same voltage range was applied to the drive electrode. The capacitance increased by the same amount. Then a drop of water was placed over the diaphragm and allowed to freeze. This created an approximately 2mm-thick ice layer. The applied 200V d.c. produced no change in capacitance, confirming that the diaphragm was locked to the ice layer. Since the sensor uses capacitive actuation, it uses very little power and is an ideal candidate for inclusion in a wireless sensing system.

DeAnna, Russell G.↗
DOE OSTI2025

Fermilab's controls development with virtual accelerator

Control Systems development is often the last thing considered when designing and building new equipment, e.g. a new detector or superconducting RF LINAC; however when the new equipment is installed, it is the first thing desired to be operational for testing. Due to frequent delays in building new equipment and project deadlines, control system development and testing is often curtailed. A way to alleviate this problem is to simulate the control system, though this will be challenging for complex systems.The Fermilab PIP-II (proton improvement plan - II) project is being constructed at Fermilab to deliver $800\,MeV$ protons of $>1\,MW$ beam power to replace the present LINAC for the remainder of the existing accelerator complex. The new LINAC consists of a warm front end (WFE), 23 superconducting RF cryomodules (of 5 types), and a beam transfer line (BTL) to the existing complex.The accelerator physics group has a parallel project to create a digital twin (DT) of the PIP-II accelerator. We have coupled the EPICS controls to this DT and are developing both the DT and EPICS software in parallel. This will allow us to develop the EPICS software framework, the HMIs, sequences, high level physics applications, and other services for use in a fully functional control system.This presentation will detail the work that we have performed to date and show demonstrations of controlling and monitoring the status of the accelerator, as well as future plans for this work.

Hanlet, Pierrick [Fermilab]↗
NASA NTRS2005

An Application-Based Performance Characterization of the Columbia Supercluster

Columbia is a 10,240-processor supercluster consisting of 20 Altix nodes with 512 processors each, and currently ranked as the second-fastest computer in the world. In this paper, we present the performance characteristics of Columbia obtained on up to four computing nodes interconnected via the InfiniBand and/or NUMAlink4 communication fabrics. We evaluate floating-point performance, memory bandwidth, message passing communication speeds, and compilers using a subset of the HPC Challenge benchmarks, and some of the NAS Parallel Benchmarks including the multi-zone versions. We present detailed performance results for three scientific applications of interest to NASA, one from molecular dynamics, and two from computational fluid dynamics. Our results show that both the NUMAlink4 and the InfiniBand hold promise for application scaling to a large number of processors.

Biswas, Rupak↗
NASA NTRS1995

Implicit schemes and parallel computing in unstructured grid CFD

The development of implicit schemes for obtaining steady state solutions to the Euler and Navier-Stokes equations on unstructured grids is outlined. Applications are presented that compare the convergence characteristics of various implicit methods. Next, the development of explicit and implicit schemes to compute unsteady flows on unstructured grids is discussed. Next, the issues involved in parallelizing finite volume schemes on unstructured meshes in an MIMD (multiple instruction/multiple data stream) fashion are outlined. Techniques for partitioning unstructured grids among processors and for extracting parallelism in explicit and implicit solvers are discussed. Finally, some dynamic load balancing ideas, which are useful in adaptive transient computations, are presented.

Venkatakrishnam, V.↗
DOE OSTI2021

PLANC: Parallel Low-rank Approximation with Nonnegativity Constraints

In this work, we consider the problem of low-rank approximation of massive dense nonnegative tensor data, for example, to discover latent patterns in video and imaging applications. As the size of data sets grows, single workstations are hitting bottlenecks in both computation time and available memory. We propose a distributed-memory parallel computing solution to handle massive data sets, loading the input data across the memories of multiple nodes, and performing efficient and scalable parallel algorithms to compute the low-rank approximation. We present a software package called Parallel Low-rank Approximation with Nonnegativity Constraints, which implements our solution and allows for extension in terms of data (dense or sparse, matrices or tensors of any order), algorithm (e.g., from multiplicative updating techniques to alternating direction method of multipliers), and architecture (we exploit GPUs to accelerate the computation in this work). We describe our parallel distributions and algorithms, which are careful to avoid unnecessary communication and computation, show how to extend the software to include new algorithms and/or constraints, and report efficiency and scalability results for both synthetic and real-world data sets.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2021

Parallelized POD-based suboptimal economic model predictive control of a state-constrained Boussinesq approximation

Motivated by an energy efficient building application, we want to optimize a quadratic cost functional subject to the Boussinesq approximation of the Navier-Stokes equations and to bilateral state and control constraints. Since the computation of such an optimal solution is numerically costly, we design an efficient strategy to compute a sub-optimal (but applicationally acceptable) solution with significantly reduced computational effort. We employ an economic Model Predictive Control (MPC) strategy to obtain a feedback control. The MPC sub-problems are based on a linear-quadratic optimal control problem subjected to mixed control and state constraints and a convection-diffusion equation, reduced with proper orthogonal decomposition. Finally, to solve each sub-problem, we apply a primal-dual active set strategy. The method can be fully parallelized, which enables the solution of large problems with real-world parameters.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2021

Hardware-in-the-Loop Investigation of Emissions Challenges in Hybrid Medium- and Heavy-Duty Powertrains Using a Pre-Production Diesel-Electric Parallel Hybrid System With and Without Stop-Start Operation

Hybrid electric powertrains are a growing market in medium- and heavy-duty applications. There is a lack of available information to understand the challenges in the integration of engine platforms into electrified powertrains, such as cold-start, restart, and load-reduction effects on emissions and emission control devices. Results from the Heavy Heavy-Duty Diesel Truck (HHDDT) cycle using a conventional medium-duty diesel engine were compared with those of a parallel hybrid architecture. Oak Ridge National Laboratory in collaboration with the US Department of Energy and Odyne Systems, LLC developed a powertrain in a hardware-in-the-loop environment, integrating the Odyne Systems, LLC medium-duty parallel hybrid system, which was used for the hybrid portion of this study. Experiments under the HHDDT cycle showed increasing improvements in fuel consumption and engine-out emissions with the integration of stop/start, hybrid, and hybrid with stop/start. However, the effects of load reduction and exhaust temperature on the thermal management strategy have shown an increase in fueling in the second part of the HHDDT cycle. Four configurations of medium-duty electrification were studied and contributed to building a unique data set containing combustion, emissions, and system integration data. Each electrification level was compared with the conventional baseline. The calibration of the conventional engine was not altered for this study. Opportunities to tailor the combustion process were identified with the stop/start strategy.

Lerin, Chloe↗
NASA NTRS2000

A Study of Influencing Factors on the Tensile Response of a Titanium Matrix Composite With Weak Interfacial Bonding

The generalized method of cells micromechanics model is utilized to analyze the tensile stress-strain response of a representative titanium matrix composite with weak interfacial bonding. The fiber/matrix interface is modeled through application of a displacement discontinuity between the fiber and matrix once a critical debonding stress has been exceeded. Unidirectional composites with loading parallel and perpendicular to the fibers are examined, as well as a cross-ply laminate. For each of the laminates studied, analytically obtained results are compared to experimental data. The application of residual stresses through a cool-down process was found to have a significant effect on the tensile response. For the unidirectional laminate with loading applied perpendicular to the fibers, fiber packing and fiber shape were shown to have a significant effect on the predicted tensile response. Furthermore, the interface was characterized through the use of semi-emperical parameters including an interfacial compliance and a "debond stress;" defined as the stress level across the interface which activates fiber/matrix debonding. The results in this paper demonstrate that if architectural factors are correctly accounted for and the interface is appropriately characterized, the macro-level composite behavior can be correctly predicted without modifying any of the fiber or matrix constituent properties.

Goldberg, Robert K.↗
DOE OSTI2025

Ensemble Simulation Techniques and Fast Randomized Algorithms

The major goals of the project were to develop and analyze new ensemble simulation techniques, including trajectory stratification and preconditioned MCMC techniques, as well as develop fast numerical linear algebra techniques closely related to ensemble simulation ideas. The trajectory stratification techniques involve simulating in parallel short trajectory fragments of a Markov process confined to a specific region of space‐time and then patching together the statistics gathered to assemble estimates of very general dynamical properties. We have also developed this approach for rare event simulation and extended the techniques to applications requiring a more general framework (such as electronic structure calculations). The preconditioned MCMC techniques involve simulating multiple Markov chains in parallel and then using information from the ensemble to speed the mixing of each individual chain. The fast randomized linear algebra methods are motivated by the diffusion Monte Carlo technique, but are applicable to finding the dominant eigenvalue of (almost) general matrices. For most non‐negative matrices, the schemes result in an error (compared to the power method) that is constant in the dimension of the problem. For more general matrices, we see a very clear sublinear cost trend in computational tests.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
NASA NTRS1999

PARAMESH: A Parallel Adaptive Mesh Refinement Community Toolkit

In this paper, we describe a community toolkit which is designed to provide parallel support with adaptive mesh capability for a large and important class of computational models, those using structured, logically cartesian meshes. The package of Fortran 90 subroutines, called PARAMESH, is designed to provide an application developer with an easy route to extend an existing serial code which uses a logically cartesian structured mesh into a parallel code with adaptive mesh refinement. Alternatively, in its simplest use, and with minimal effort, it can operate as a domain decomposition tool for users who want to parallelize their serial codes, but who do not wish to use adaptivity. The package can provide them with an incremental evolutionary path for their code, converting it first to uniformly refined parallel code, and then later if they so desire, adding adaptivity.

MacNeice, Peter↗
DOE OSTI2024

CaTS: Integration of Geant4 and Opticks

CaTS [6]is an advanced example that is part of Geant4 since version 11.0. It demonstrates the use of Opticks to offload the simulation of optical photons to GPUs. Opticks interfaces with the Geant4 toolkit to collect all the necessary information to generate and trace optical photons, re-implements the optical physics processes to be run on the GPU, and automatically translates the Geant4 geometry into a GPU appropriate format. To trace the photons, Opticks uses NVIDIA OptiX®. In this report, we describe CaTS and the integration of Opticks with Geant4. We demonstrate that the generation and tracing of optical photons represents an ideal application to be offloaded to GPUs, fully utilizing the high degree of available parallelism. In a typical liquid argon TPC simulation, a speedup of several hundred times is observed compared to an equivalent simulation using single threaded Geant4.

Wenzel, Hans↗
DOE OSTI2023

Multi-mode analysis of surface losses in a superconducting microwave resonator in high magnetic fields

This paper reports on a surface impedance measurement of a bulk metal niobium–titanium superconducting radio frequency (SRF) cavity in a magnetic field (up to 10 T). Here, a novel method is employed to decompose the surface resistance contributions of the cylindrical cavity end caps and walls using measurements from multiple TM cavity modes. The results confirm that quality factor degradation of a NbTi SRF cavity in a high magnetic field is primarily from surfaces perpendicular to the field (the cavity end caps), while parallel surface resistances (the walls) remain relatively constant. This result is encouraging for applications needing high Q cavities in strong magnetic fields, such as the Axion Dark Matter eXperiment because it opens the possibility of hybrid SRF cavity construction to replace conventional copper cavities.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2023

libEnsemble: A complete Python toolkit for dynamic ensembles of calculations

Almost all science and engineering applications eventually stop scaling: their runtime no longer decreases as available computational resources increase. Therefore, many applications will struggle to efficiently use emerging extreme-scale high-performance, parallel, and distributed systems. libEnsemble is a complete Python toolkit and workflow system for intelligently driving ensembles of experiments or simulations at massive scales. It enables and encourages multidisciplinary design, decision, and inference studies portably running on laptops, clusters, and supercomputers.

97 MATHEMATICS AND COMPUTING↗
NASA NTRS1974

The ASSESS program documenting and evaluating low cost techniques for conducting research in the flight environment

The Airborne Science Office (ASO) of the Ames Research Center has for 10 years operated an airborne scientific research program in infrared astronomy and other disciplines. The Lear Jet, CV-990, and C-141 flying laboratories are flown by ASO crews, while the major responsibility for defining, developing, and operating the experimental equipment is placed on individual researchers, who have included scientists from many countries. The ASSESS (Airborne Science/Shuttle Experiment Systems Simulation) program consists of two phases: Phase A documents the present management and operational practices of the ASO, and Phase B consists of airborne research missions constrained (for example, by crew confinement) to simulate certain aspects of experimental operations on Shuttle/Spacelab missions. Various parallels between the Airborne Science Program and Spacelab are pointed out and their applications to Spacelab planning are discussed.

Weaver, L. B.↗
NASA NTRS1990

Porous-Floating-Gate Field-Effect Transistor

Porous-floating-gate, "vertical" field-effect transistor proposed as programmable analog memory device especially suitable for use in electronic neural networks. Analog value of electrical conductance of device represents synaptic weight (strength of synaptic connection) repeatedly modified by application of suitable writing or erasing voltage. Suited for hardware implementations of massively parallel neural-network architectures for two important reasons: vertical transistor structure requires only two external electrodes, and use of tailored amorphous semiconductors provides choice of very wide range of low conductivity values, dictated by overall power dissipation requirements in massively parallel neural-network circuits.

Thakoor, Anilkumar P.↗
NASA NTRS1990

CFD code evaluation for internal flow modeling

Research on the computational fluid dynamics (CFD) code evaluation with emphasis on supercomputing in reacting flows is discussed. Advantages of unstructured grids, multigrids, adaptive methods, improved flow solvers, vector processing, parallel processing, and reduction of memory requirements are discussed. As examples, researchers include applications of supercomputing to reacting flow Navier-Stokes equations including shock waves and turbulence and combustion instability problems associated with solid and liquid propellants. Evaluation of codes developed by other organizations are not included. Instead, the basic criteria for accuracy and efficiency have been established, and some applications on rocket combustion have been made. Research toward an ultimate goal, the most accurate and efficient CFD code, is in progress and will continue for years to come.

Chung, T. J.↗
NASA NTRS1990

Supercomputing systems - A projection to 2000

Advances in computer architecture, computer science, computational methods, and constituent technologies are expected to lead to significant advances in the performance of scientific supercomputing system capabilities over the next decade. By the year 2000, single 1-in-sq dies are projected to incorporate four processors, each of which would be operating faster than 750 million instructions per second (MIPS) for a total on-chip processing performance in excess of 2000 MIPS. Scalable parallel processors can be expected to contain thousands of such multiple processor chips. In general, semiconductor performance advances appear to change about one order of magnitude every five years. Rotating magnetic memory and communications technology are not advancing as rapidly, with the result that the allocation of functions within the system configurations fo future supercomputer systems will require important changes. Availability of massively parallel heterogeneous processing capabilities should be a catalyst leading to new approaches for applications.

Lundstrom, S. F.↗
NASA NTRS1992

Network issues for large mass storage requirements

File Servers and Supercomputing environments need high performance networks to balance the I/O requirements seen in today's demanding computing scenarios. UltraNet is one solution which permits both high aggregate transfer rates and high task-to-task transfer rates as demonstrated in actual tests. UltraNet provides this capability as both a Server-to-Server and Server-to-Client access network giving the supercomputing center the following advantages highest performance Transport Level connections (to 40 MBytes/sec effective rates); matches the throughput of the emerging high performance disk technologies, such as RAID, parallel head transfer devices and software striping; supports standard network and file system applications using SOCKET's based application program interface such as FTP, rcp, rdump, etc.; supports access to the Network File System (NFS) and LARGE aggregate bandwidth for large NFS usage; provides access to a distributed, hierarchical data server capability using DISCOS UniTree product; supports file server solutions available from multiple vendors, including Cray, Convex, Alliant, FPS, IBM, and others.

Perdue, James↗