Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PIN”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 991 records · Page 55

ATF-2 Ramp Conceptual Design Report

The following report documents the conceptual design for the ATF-2 Ramp experiment. The experiment aims to fill the in-pile irradiation testing gap to conduct integral ramp testing, which was created by the closure of R2, Osiris, and Halden test reactors. The concept involves the simultaneous ramping of three fuel pins using a power axial locator mechanism in the Loop-2A testing facility in the center flux trap of the advanced test reactor (ATR). The three fuel pins are ramped in individual coolant channels containing a prototypic PWR environment. Rod failure will be detected using a fuel rod elongation sensor attached to the fuel pin upper end cap. An axial stack of concentric hafnium and zirconium shrouds will be used to shape the flux around the test pins to create different power levels in each pin and to ensure the peak power location of each pin remains in the center of the test rod. Monte Carlo simulations are used to demonstrate the viability of this design concept.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Data Mining – Image Analysis of Radiography for Zr Redistribution

The research effort described in this report represents a first attempt to investigate the radial redistribution of Zr in ternary fuel alloys U-xPu-10Zr (x = 0, 8, 19) irradiated in the in-reactor fuel experiments during the operation of the U.S. Department of Energy’s (DOE’s) Experimental Breeder Reactor II (EBR-II) at Idaho National Laboratory (INL) using methods of image processing on post-irradiation neutron radiographs. Approximately 130,000 metal fuel pins were irradiated in EBR-II during its 30 years of operation to develop and characterize existing and prospective fuels. For many of the metal fuel irradiation experiments, neutron radiography imaging was performed historically now allowing application of modern image analysis techniques to characterize fuel behavior, such as fuel swelling, fluff formation, and now, fuel alloy constituent redistribution. The redistribution of fuel components depends on the temperature field, radially, within the fuel. Specifically, Zr is expected to redistribute radially towards the center of the pin, as well as towards the outer zones. Currently, direct imaging of a pin cross-section through optical methods or scanning electron microscopy (SEM) is used to study the constituents’ redistribution, which is very time-consuming and can only be applied to a limited number of pins. An automated image processing technique allowing for the investigation of fuel radial redistribution zones would significantly accelerate data analysis. In general, if the fuel temperature is hot enough, three redistribution zones are expected, corresponding to the main fuel components (e.g., U, Pu, Zr). While more assessment will be performed in fiscal year (FY)-2023, it seems possible to differentiate the pins according to their fuel composition using image analysis techniques on neutron radiographs of metallic fuel pins based on the analysis to date.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Comparison of Zirconium Redistribution in BISON EBR-II Models Using FIPD and IMIS Databases with Experimental Post Irradiation Examination

Metallic fuels have seen increased interest for future sodium fast reactors due to their material properties: high thermal conductivities and advantageous neutronic properties allow for greater fission densities. One drawback to typical metallic fuels is zirconium redistribution, which impacts this advantageous material and its neutronic properties. Unfortunately, the processes behind zirconium migration behavior are understood using first principles, so before these fuels are implemented in future fast reactors, characterization and fuel qualification regimes must be completed. These activities can be supported through the use of robust modeling using the most accurate empirical models currently available to fuel researchers around the world. The tool that allows researchers to model this complex coupled thermo-mechanical behavior and nuclear properties is BISON. Additionally, BISON model parameters need to be compared against PIE measurements. The current work utilizes two fuel pins from EBR-II experiment X441 to optimize various model parameters, including porosity correction factor, thermal conductivity, phase transition temperature, and diffusion coefficient multipliers, before implementing the final model for seven fuel pins with differing characteristics. To properly evaluate the BISON simulations, the results are compared to PIE metallography data for each fuel pin, to ensure the zirconium redistribution is properly reflected in the simulation results. Six out of seven analyzed fuel pins demonstrate good agreement between the metallography images and BISON results, showing alignment of the Zr-rich, Zr-depleted, and moderately Zr-enriched zones at various axial heights along the fuel pins. Further work is needed to refine the model parameters for general pin use.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Testing of uranium nitride fuel in T-111 cladding at 1200 K cladding temperature

Two groups of six fuel pins each were assembled, encapsulated, and irradiated in the Plum Brook Reactor. The fuel pins employed uranium mononitride (UN) in a tantalum alloy clad. The first group of fuel pins was irradiated for 1500 hours to a maximum burnup of 0.7-atom-percent uranium. The second group of fuel pins was irradiated for about 3000 hours to a maximum burnup of 1.0-atom-percent uranium. The average clad surface temperature during irradiation of both groups of fuel pins was approximately 1200 K. The postirradiation examination revealed the following: no clad failures or fuel swelling occurred; less than 1 percent of the fission gases escaped from the fuel; and the clad of the first group of fuel pins experienced clad embrittlement whereas the second group, which had modified assembly and fabrication procedures to minimize contamination, had a ductile clad after irradiation.

Rohal, R. G.↗

Avalanche-diode oscillator circuit with tuning at multiple frequencies

Detailed theoretical analysis of three different modes or types of high efficiency oscillation in a PIN diode are presented. For the TRAPATT mode in a PIN diode, it is shown that a traveling avalanche zone is not necessary to generate a dense trapped plasma. An economical computer program for TRAPATT oscillations in a PIN diode is described. Typical results of diode power, dc-to-RF conversion efficiency, and required circuit impedances are presented for several different current waveforms. A semianalytical solution for a second type of high efficiency mode in a PIN diode is derived assuming a rectangular current waveform. A quasi-static approximation is employed to derive a semianalytical solution for the voltage across a PIN diode in a third mode, where avalanching occurs during a major portion of a half cycle. Calculations for this mode indicate that the power increases proportionally to the magnitude of the drive current with a small decrease in efficiency relative to the ordinary TRAPATT mode. An analytical solution is also given for a PIN diode, where it is assumed that the ionization coefficient is a step function. It is shown that the step-ionization approximation permits one to draw possible patterns of avalanche region in the depletion layer as a function of time. A rule governing admissible patterns is derived and an example solution given for one admissible pattern. Preliminary experimental results on the high-efficiency oscillations are presented and discussed. Two different experimental circuits, which used channel-dropping filters to provide independent harmonic tuning, are described. Simpler circuits used to produce high-efficiency oscillations are discussed. Results of experiments using inexpensive Fairchild FD300 diodes are given.

Parker, D.↗

Impact of device level faults in a digital avionic processor

This study describes an experimental analysis of the impact of gate and device-level faults in the processor of a Bendix BDX-930 flight control system. Via mixed mode simulation, faults were injected at the gate (stuck-at) and at the transistor levels and, their propagation through the chip to the output pins was measured. The results show that there is little correspondence between a stuck-at and a device-level fault model, as far as error activity or detection within a functional unit is concerned. In so far as error activity outside the injected unit and at the output pins are concerned, the stuck-at and device models track each other. The stuck-at model, however, overestimates, by over 100 percent, the probability of fault propagation to the output pins. An evaluation of the Mean Error Durations and the Mean Time Between Errors at the output pins shows that the stuck-at model significantly underestimates (by 62 percent) the impact of an internal chip fault on the output pins. Finally, the study also quantifies the impact of device fault by location, both internally and at the output pins.

Suk, Ho Kim↗

Clevis joint for deployable space structures

This invention relates generally to pin clevis joints, and more particularly, to zero play pin clevis joints for connecting structural members of a deployable space structure. A joint includes a pin, a tang, and a shackle. The pin is tapered at the same angle as the bores extending through the projections of the shackle and the tang. A spring washer biases the tang onto the tapered sidewall of the pin. The invention solves the free play problem associated with deployable space structures by using a tapered pin which is held in tapered holes by the spring washers.

Rhodes, Marvin D.↗

Flow Trajectories in Friction Stir Welding

In the Friction Stir Welding (FSW) process, a rotating, shouldered tool with a threaded pin is inserted under pressure along the seam of two pieces of metal which are tightly clamped together, and secured against a rigid anvil underneath. The rotating pin travels along the seam and through a combination of pressure and friction heating produces a zone of plastic deformation around the pin within the workpiece on either side of the seam. As the pin is moved in the direction of welding, the plasticised material moves around the tool and bonds together behind it. The elements of the material flow behavior are a combination of three elements. There is a rotational transport of material being carried around the tool, extrusion of material being forced around the pin on both sides into the cavity created behind it, and a lifting and dropping of material as it is stirred and mixed by the rotating action of the pin. It was assumed that rotational motion of the plastic zone is the primary mechanism for transport of material around the welding tool. A kinematic mathematical model was used to compute trajectories of material movement for various distributions of rotational slip within the plastic zone. These trajectories were then compared with the results of an experiment that produced radiographs of markers embedded in a workpiece that was welded with the FSW process. It was assumed that the copper wire markers retained their original length as the aluminum material flowed around them. The kinematic model included a constraint so that the displacements were such that the total length of the wire markers did not increase after deformation. There was good agreement between the calculated trajectories for the case of localized slip at the outer surface of the plastic deformation zone and the radiographs of the copper wire markers. The trajectories differed markedly from the radiograph traces when a distributed slip zone was assumed. It was concluded that the flow field could be described generally by a rotating plug model with slip occurring on the surface at the outer boundary of the plastic zone.

Bernstein, Edward L.↗

Deployment hinge

A hinge (20) includes two hinge plates (22, 24) and a connecting hinge pin (32). A coil spring (48) supported on a bushing (44) overlies the hinge pin (32), which is free to move along its longitudinal axis (30). A cam follower (42) on the hinge pin (32) engages a cam (32) mounted to one of the hinge plates (22), so that the hinge pin (32) slides longitudinally as the hinge plates (22, 24) pivot relative to each other about the hinge pin (32). As the hinge pin (32) slides longitudinally, it axially compresses or decompresses the spring (48). The cam (32) is oriented such that pivoting of the hinge plates (22, 24) in either direction from an open position compresses the spring (48), providing a restoring force which tends to retain the hinge plates (22, 24) in the open position.

Tourville, Thomas↗

A Second Look at Neutron Resonance Transmission Analysis as a Spent Fuel NDA Technique

Many different nondestructive analysis techniques are currently being investigated as a part of the United States Department of Energy's Next Generation Safeguards Initiative (NGSI) seeking methods to quantify plutonium in spent fuel. Neutron Resonance Transmission Analysis (NRTA) is one of these techniques. Having first been explored in the mid-1970s for the analysis of individual spent-fuel pins a second look, using advanced simulation and modeling methods, is now underway to investigate the suitability of the NRTA technique for assaying complete spent nuclear fuel assemblies. The technique is similar to neutron time-of-flight methods used for cross-section determinations but operates over only the narrow 0.1-20 eV range where strong, distinguishable resonances exist for both the plutonium (239, 240, 241,242Pu) and uranium (235,236,238U) isotopes of interest in spent fuel. Additionally, in this energy range resonances exists for six important fission products (99Tc, 103Rh, 131Xe, 133Cs, 145Nd, and 152Sm) which provide additional information to support spent fuel plutonium assay determinations. Initial modeling shows excellent agreement with previously published experimental data for measurements of individual spent-fuel pins where plutonium assays were demonstrated to have a precision of 2-4%. Within the simulation and modeling analyses of this project scoping studies have explored fourteen different aspects of the technique including the neutron source, drift tube configurations, and gross neutron transmission as well as the impacts of fuel burn up, cooling time, and fission-product interferences. These results show that NRTA may be a very capable experimental technique for spent-fuel assay measurements. The results suggest sufficient transmission strength and signal differentiability is possible for assays through up to 8 pins. For an 8-pin assay (looking at an assembly diagonally), 64% of the pins in a typical 17 ? 17 array of a pressurized water reactor fuel assembly can be part of a complete transmission assay measurement with high precision. Analysis of rows with up to 12 pins may also be feasible but with diminished precision. Preliminary data analysis of an NRTA simulation has demonstrated the simplicity of the technique.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Friction stirring interlocking of dissimilar materials

A method for solid state joining of dissimilar materials using a friction stir welding device wherein a pin is inserted through an aperture defined in a first material and a second material to hold the materials together and then held in place by friction stir welding a portion of the pin to a material adjacent said pin, or by friction stir welding a cap or plug that holds the pin in place to the adjacent material. The result is a connection or join wherein the central portion of the pin is not friction stir welded but the portions holding the pin in place (the ends or caps) generally are.

Whalen, Scott A.↗

Boards having solderless interconnects

This disclosure provides systems, methods, and apparatus related to printed circuit boards. In one aspect, a device includes a first board and a second board. The first board includes at least two pins defined at an end of the first board. The first pin and the second pin are positioned along a first line and parallel to the first line. The second board includes at least two slots defined at an end of the second board. The first slot and the second slot are positioned along a second line and are angled from the second line by about ±10° to 15°. Each of the pins in the first board is engaged with each of the slots in the second board and forms an electrical connection between the first pin and the first slot and the second pin and the second slot.

Wielandt, Stijn↗

System and method of making a crankshaft with alternate materials

A crankshaft for an internal combustion engine is provided. The crankshaft comprises at least four main journals aligned on a crankshaft axis of rotation defining a centerline. The crankshaft further comprises at least three pin journals. Each pin journal is disposed about a respective pin journal axis and positioned between the main journals. Each of the pin journals is joined to a pair of crank arms. Each pair of crank arms is joined to a respective main journal. Each of the main journals, pin journals, and crank arms is made of a first metallic material. Each crank arm has an over-molded counterweight metallurgically bonded thereto. Each counterweight is disposed opposite a respective pin journal relative to the centerline for balance and stability. Each counterweight is made of a second metallic material. The crankshaft has a weight ratio of the second metallic material to the first metallic material of between 0.20 to 0.50.

Klemstine, David C.↗

WIMS/PANTHER analysis of UO{sub 2}/MOX cores using embedded super-cells

This paper describes a method of analysing PWR UO{sub 2}MOX cores with WIMS/PANTHER. Embedded super-cells, run within the reactor code, are used to correct the standard methodology of using 2-group smeared data from single assembly lattice calculations. In many other codes the weakness of this standard approach has been improved for MOX by imposing a more realistic environment in the lattice code, or by improving the sophistication of the reactor code. In this approach an intermediate set of calculations is introduced, leaving both lattice and reactor calculations broadly unchanged. The essence of the approach is that the whole core is broken down into a set of 'embedded' super-cells, each extending over just four quarter assemblies, with zero leakage imposed at the assembly mid-lines. Each supercell is solved twice, first with a detailed multi-group pin-by-pin solution, and then with the standard single assembly approach. Correction factors are defined by comparing the two solutions, and these can be applied in whole core calculations. The restriction that all such calculations are modelled with zero leakage means that they are independent of each other and of the core-wide flux shape. This allows parallel pre-calculation for the entire cycle once the loading pattern has been determined, in much the same way that single assembly lattice calculations can be pre-calculated once the range of fuel types is known. Comparisons against a whole core pin-by-pin reference demonstrates that the embedding process does not introduce a significant error, even after burnup and refuelling. Comparisons against a WIMS reference demonstrate that a pin-by-pin multi-group diffusion solution is capable of capturing the main interface effects. This therefore defines a practical approach for achieving results close to lattice code accuracy, but broadly at the cost of a standard reactor calculation. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Recent developments in DYNSUB: New models, code optimization and parallelization

DYNSUB is a high-fidelity coupled code system consisting of the reactor simulator DYN3D and the sub-channel code SUBCHANFLOW. It describes nuclear reactor core behavior with pin-by-pin resolution for both steady-state and transient scenarios. In the course of the coupled code system's active development, super-homogenization (SPH) and generalized equivalence theory (GET) discontinuity factors may be computed with and employed in DYNSUB to compensate pin level homogenization errors. Because of the largely increased numerical problem size for pin-by-pin simulations, DYNSUB has bene fitted from HPC techniques to improve its numerical performance. DYNSUB's coupling scheme has been structurally revised. Computational bottlenecks have been identified and parallelized for shared memory systems using OpenMP. Comparing the elapsed time for simulating a PWR core with one-eighth symmetry under hot zero power conditions applying the original and the optimized DYNSUB using 8 cores, overall speed up factors greater than 10 have been observed. The corresponding reduction in execution time enables a routine application of DYNSUB to study pin level safety parameters for engineering sized cases in a scientific environment. (authors)

97 MATHEMATICS AND COMPUTING↗

Stabilizers for a vehicle cooling module

A stabilizing arrangement of a cooling system module of a vehicle includes stabilizer pins attached to the vehicle cooling system module. Stabilizer slots are incorporated into a component of the chassis of the vehicle, such as a frame extender. The stabilizer slots may be formed as an upwards opening U-shape. Bushings are attached to the stabilizer pins. The stabilizer pins and bushings extend laterally into and engage with the stabilizer slots. Upon installation, the stabilizer pins and bushings are aligned with the stabilizer slots as the cooling system module is lowered onto the ISO mounts. The stabilizer pins and bushings slide vertically downwards into the stabilizer slots as the cooling system module is lowered into place. The simpler stabilizer pins, bushings, and stabilizer slots thereby take the place of expensive, time consuming, complex, labor intensive, and space consuming stay rod arrangements.

Wu, Shouhao↗

Effects of Coolant Void Condition on Melt Fragmentation using Simulants in Initial Phase of Metal-fueled SFR Severe Accident

Metal fuel has inherent safety characteristics, especially in severe accident conditions. However, the metal-fueled SFR severe accident scenarios need to be categorized since overall severe accident mitigation strategies have not been prepared. In addition, these mitigation strategies should be classified in specific phases. In an initial phase of metal-fueled SFR severe accident scenarios, fuel melting, and cladding failures would occur. After the occurrence of the cladding breach, the molten metal fuel would be ejected into a coolant channel due to fission gas in fuel cavity or rapid evaporation of sodium bond. This is called Ex-pin phenomena. There are few studies considering the Ex-pin phenomena of metal fuel. Related representative studies are transient reactor test facility (TREAT) M series tests. The TREAT M series tests provided fundamental metal fuel performance in transient condition. They informed partial experimental data such as the amount of melt ejected into coolant channel after the cladding failure. However, these experimental data did not examine the melt behavior during the Ex-pin phenomena. In metal-fueled SFR, it is a known fact that the negative reactivity feedback occurs in the initial phase of severe accident. In an unprotected loss-of-flow (ULOF) accident, the void-reactivity feedback may be positive depending on where in the reactor core the sodium voiding occurs. However, molten metal fuel would be better dispersed upward compared to those of an oxide fuel and significant negative reactivity feedback could be induced through such behaviors. Thus, a key safety strategy to mitigate the accident progression at the initial phase of severe accident is to discharge melt upwards out of the core. In this paper, the upward discharge of melt is defined as melt levitation. Such melt levitation could ensure early termination of severe accident. There could be different melting behaviors inside the pin depending on reactor types or the type of fuel. In case of pressurized water reactor (PWR) oxide fuel-water system, the rapid power excursion would initiate melting of fuel at the surface of the pellets. In this paper, the ULOF accident for the metal-fueled SFR is considered as an accident scenario. To induce the melt levitation, the driving force should be clarified. Heo et al. observed a built-up vapor pressure was suggested as one of the driving forces for the upward dispersion of the molten materials. The following factors also have the potential to induce the melt levitation; the pressure induced by fission gas in the cavity or rapid boiling of sodium bond, natural circulation flow of the sodium, the sodium vapor flow generated by the difference between inlet and outlet plenum in the reactor core, the built-up vapor pressure due to the fuel-coolant interaction etc. These factors are balanced each other. They should be examined through the Ex-pin experiments. Before conducting a parametric study for each factor, the general behavior of the molten metal fuel should be investigated in the coolant channel. Since rapid sodium coolant boiling could occur in the initial phase of severe accident scenarios, the molten fuel would be ejected and fragmented in voided channel. Unlike previous studies concerning an un-voided channel, differences in melt behavior in the voided channel are expected. In present study, molten material behavior was evaluated to reveal their characteristics in voided channel. The Ex-pin experiments were performed in both un-voided and voided channel, thus such behavior differences were explicitly observed. In the lab-scale experiments, the un-voided and voided channel were reflected by coolant-filled and air-filled channel, respectively. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Design of a proteus lattice representative of a burnt and fresh fuel interface at power conditions in light water reactors

The research program LIFE (Large-scale Irradiated Fuel Experiment) between PSI and Swissnuclear has been started in 2006 to study the interaction between large sets of burnt and fresh fuel pins in conditions representative of power light water reactors. Reactor physics parameters such as flux ratios and reaction rate distributions ({sup 235}U and {sup 238}U fissions and {sup 238}U capture) are calculated to estimate an appropriate arrangement of burnt and fresh fuel pins within the central element of the test zone of the zero-power research reactor PROTEUS. The arrangement should minimize the number of burnt fuel pins to ease fuel handling and reduce costs, whilst guaranteeing that the neutron spectrum in both burnt and fresh fuel regions and at their interface is representative of a large uniform array of burnt and fresh pins in the same moderation conditions. First results are encouraging, showing that the burnt/fresh fuel interface is well represented with a 6 x 6 bundle of burnt pins. The second part of the project involves the use of TSUNAMI, CASMO-4E and DAKOTA to perform parametric and optimization studies on the PROTEUS lattice by varying its pitch (P) and fraction of D{sub 2}O in moderator (F{sub D2O}) to be as representative as possible of a power light water reactor core at hot full power conditions at beginning of cycle (BOC). The parameters P and F{sub D2O} that best represent a PWR at BOC are 1.36 cm and 5% respectively. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗