Results for “Modal Analysis” — Page 55

NASA NTRS2022

Accelerance Decoupling: An Approach for Removing the Influence of the Test Stand from the Integrated Modal Test

The main objective for launch vehicle (LV) modal testing is to quantify the LV’s modal properties in the free-free state (post pad separation). However, given the size of most LV systems, free-free testing is a challenge and often not feasible. With this, a test stand, typically the launch pad itself, is introduced as the means of support. This shifts the challenge to developing robust numerical methods for removing the influence of the launch pad from the integrated system modal test. The Space Launch System (SLS) is no exception where the mobile launcher (ML) is used to support the vehicle for the integrated modal test (IMT). For the IMT, it is well understood from pre-test analysis with finite element models (FEMs) of the SLS and SLS coupled to ML that the ML has a significant influence on the SLS modal properties especially in the lower frequency range where the primary SLS bending modes exist. An accelerance decoupling (AD) method has been formulated for the purpose of “subtracting out” the influence of the ML from the IMT results. With AD, the SLS decoupled frequency response functions (FRFs) are directly extracted from the IMT FRFs. The subject approach is aimed to utilize measured data only and achieve a robust FRF decoupling scheme. AD is derived from a widely used coupling technique called “Receptance Coupling” (RC). The AD core equation reverses the RC process and utilizes a pair of auxiliary equations that enable the core equation to be resolved based on measured data only. In AD, the decoupled component FRFs are extracted from the coupled system FRFs with a transformation to remove the contribution of the “subtractive component”. This paper addresses the AD’s operational flexibility to resolve SLS free-free modal properties from coupled system measured data but also the possibility to include data from FEM if there is enough confidence in the FEM or if it is asserted that the effect to the final outcome is reasonable.

Accelerance decoupling↗

NASA NTRS2022

Accelerance Decoupling: An Approach for Removing the Influence of the Test Stand from the Integrated Modal Test

The main objective for launch vehicle (LV) modal testing is to quantify the LV’s modal properties in the free-free state (post pad separation). However, given the size of most LV systems, free-free testing is a challenge and often not feasible. With this, a test stand, typically the launch pad itself, is introduced as the means of support. This shifts the challenge to developing robust numerical methods for removing the influence of the launch pad from the integrated system modal test. The Space Launch System (SLS) is no exception where the mobile launcher (ML) is used to support the vehicle for the integrated modal test (IMT). For the IMT, it is well understood from pre-test analysis with finite element models (FEMs) of the SLS and SLS coupled to ML that the ML has a significant influence on the SLS modal properties especially in the lower frequency range where the primary SLS bending modes exist. An accelerance decoupling (AD) method has been formulated for the purpose of “subtracting out” the influence of the ML from the IMT results. With AD, the SLS decoupled frequency response functions (FRFs) are directly extracted from the IMT FRFs. The subject approach is aimed to utilize measured data only and achieve a robust FRF decoupling scheme. AD is derived from a widely used coupling technique called “Receptance Coupling” (RC). The AD core equation reverses the RC process and utilizes a pair of auxiliary equations that enable the core equation to be resolved based on measured data only. In AD, the decoupled component FRFs are extracted from the coupled system FRFs with a transformation to remove the contribution of the “subtractive component”. This paper addresses the AD’s operational flexibility to resolve SLS free-free modal properties from coupled system measured data but also the possibility to include data from FEM if there is enough confidence in the FEM or if it is asserted that the effect to the final outcome is reasonable.

Accelerance decoupling↗

NASA NTRS2022

Accelerance Decoupling: An Approach for Removing the Influence of the Test Stand from the Integrated Modal Test

The main objective for launch vehicle (LV) modal testing is to quantify the LV’s modal properties in the free-free state (post pad separation). However, given the size of most LV systems, free-free testing is a challenge and often not feasible. With this, a test stand, typically the launch pad itself, is introduced as the means of support. This shifts the challenge to developing robust numerical methods for removing the influence of the launch pad from the integrated system modal test. The Space Launch System (SLS) is no exception where the mobile launcher (ML) is used to support the vehicle for the integrated modal test (IMT). For the IMT, it is well understood from pre-test analysis with finite element models (FEMs) of the SLS and SLS coupled to ML that the ML has a significant influence on the SLS modal properties especially in the lower frequency range where the primary SLS bending modes exist. An accelerance decoupling (AD) method has been formulated for the purpose of “subtracting out” the influence of the ML from the IMT results. With AD, the SLS decoupled frequency response functions (FRFs) are directly extracted from the IMT FRFs. The subject approach is aimed to utilize measured data only and achieve a robust FRF decoupling scheme. AD is derived from a widely used coupling technique called “Receptance Coupling” (RC). The AD core equation reverses the RC process and utilizes a pair of auxiliary equations that enable the core equation to be resolved based on measured data only. In AD, the decoupled component FRFs are extracted from the coupled system FRFs with a transformation to remove the contribution of the “subtractive component”. This paper addresses the AD’s operational flexibility to resolve SLS free-free modal properties from coupled system measured data but also the possibility to include data from FEM if there is enough confidence in the FEM or if it is asserted that the effect to the final outcome is reasonable.

Accelerance decoupling↗

DOE OSTI2021

Simultaneous x-ray and neutron 4D tomographic study of drying-driven hydro-mechanical behavior of cement-based materials at moderate temperatures

The drying of cement-based materials is intimately related to their durability, which has significant economic, social and environmental repercussions. The evolution of the saturation of the pore network and the associated drying shrinkage are in fact leading causes of cracking and of the ensuing penetration of aggressive chemicals. This process is highly heterogeneous, due to the thermo-hydric spatial gradients developing in the material from the exposed surfaces to its core and because of local effects, driven by the intrinsically heterogeneous micro-structure (e.g., by the distribution of pores and aggregates). It follows that macroscopic, sample-scale measurements cannot fully disclose the complexity of the underlying processes. In the last few decades, significant advances in full-field techniques have allowed an unprecedented insight into these local processes. For cement-based materials, x-ray and neutron tomography lend themselves as ideal, and highly complementary, tools for the study of their thermo-hydro-mechanical behavior. Notably, the high sensitivity to density variations of x-ray imaging gives access to the developments of fractures, in 4D (3D + time). On the other hand, neutron tomography allows the study of the evolution of the moisture field in 4D, thanks to its high hydrogen sensitivity. The combination of these two techniques provides a unique insight in thermo-hydro-mechanical couplings, e.g., the effect of cracks on the water content field. This contribution presents novel 5D datasets (3D tomographies along time, plus truly simultaneous x-ray and Neutron rapid acquisitions) in-operando of a cement paste and of a concrete sample heated at moderate temperatures (up to 140{sup ∘}C). The analysis of this 5D data-set (once aligned in time and across modalities) allows for example a quantification of the 4D moisture profiles which were found to predict an overall water loss at hydric equilibrium coherent with the corresponding analytical analysis. In the cement paste sample, the x-ray dataset captures the evolution of an extensive cracking network, opening and propagation toward the core of the sample. A novel analysis procedure is here proposed which allows the extraction of these fractures and the analysis of their interplay with local drying as captured through neutron imaging. This for example reveals the depth of penetration of drying in the vicinity of the fractures along time, which is essential for the assessment and calibration of hydro-mechanical coupled models.

36 MATERIALS SCIENCE↗

NASA NTRS1980

Rotordynamics analysis of the Space Shuttle main engine high-pressure oxidizer pump

This study describes the rotordynamics analysis of the Space Shuttle Main Engine (SSME) high-pressure oxidizer turbopump. Modal synthesis methods were used to account for the complex coupling of the pump and engine structure. Cross-coupling elements effecting rotor stability were included in the analysis. Results of the analysis indicated that smaller bearing clearances and a smooth turbine interstage seal would result in longer bearing life and improved stability. Subsequent testing with these design features has shown the same results.

Rowan, B. F.↗

NASA NTRS1978

Instrumental variables algorithm for modal parameter identification in flutter testing

The paper is concerned with the task of estimating modal parameters from system response measurement in aircraft flutter testing. A frequency-domain derivation of an instrumental-variables algorithm is presented for a linear time-invariant dynamic system of order n. Basically, this algorithm fits a set of poles and zeros to the measured transfer function. An illustrative example is provided regarding the application of the algorithm to aeroelasticity testing. It is shown that the algorithm can be implemented for on-line data reduction with a microcomputer-based analysis system. By using instrumental variables the sensitivity of the modal parameter estimates to noise in the system-response measurements is reduced greatly. The algorithm is expected to be a powerful and valuable tool for on-line estimation of modal parameters in flutter testing and should be useful in control system and structural dynamics tests.

Johnson, W.↗

NASA NTRS1993

Simulating flight boundary conditions for orbiter payload modal survey

An approach to simulate the characteristics of the payload/orbiter interfaces for the payload modal survey was developed. The flexure designed for this approach is required to provide adequate stiffness separation in the free and constrained interface degrees of freedom to closely resemble the flight boundary condition. Payloads will behave linearly and demonstrate similar modal effective mass distribution and load path as the flight if the flexure fixture is used for the payload modal survey. The potential non-linearities caused by the trunnion slippage during the conventional fixed base modal survey may be eliminated. Consequently, the effort to correlate the test and analysis models can be significantly reduced. An example is given to illustrate the selection and the sensitivity of the flexure stiffness. The advantages of using flexure fixtures for the modal survey and for the analytical model verification are also demonstrated.

Chung, Y. T.↗

NASA NTRS1997

Autonomous Modal Identification of the Space Shuttle Tail Rudder

Autonomous modal identification automates the calculation of natural vibration frequencies, damping, and mode shapes of a structure from experimental data. This technology complements damage detection techniques that use continuous or periodic monitoring of vibration characteristics. The approach shown in the paper incorporates the Eigensystem Realization Algorithm (ERA) as a data analysis engine and an autonomous supervisor to condense multiple estimates of modal parameters using ERA's Consistent-Mode Indicator and correlation of mode shapes. The procedure was applied to free-decay responses of a Space Shuttle tail rudder and successfully identified the seven modes of the structure below 250 Hz. The final modal parameters are a condensed set of results for 87 individual ERA cases requiring approximately five minutes of CPU time on a DEC Alpha computer.

Pappa, Richard S.↗

DOE OSTI2019

Novel imaging techniques of rectal cancer: what do radiomics and radiogenomics have to offer? A literature review

Introduction: As computational capabilities have advanced, radiologists and their collaborators have looked for novel ways to analyze diagnostic images. This has resulted in the development of radiomics and radiogenomics as new fields in medical imaging. Radiomics and radiogenomics may change the practice of medicine, particularly for patients with colorectal cancer. Radiomics corresponds to the extraction and analysis of numerous quantitative imaging features from conventional imaging modalities in correlation with several endpoints, including the prediction of pathology, genomics, therapeutic response, and clinical outcome. In radiogenomics, qualitative and/or quantitative imaging features are extracted and correlated with genetic profiles of the imaged tissue. Thus far, several studies have evaluated the use of radiomics and radiogenomics in patients with colorectal cancer; however, there are challenges to be overcome before its routine implementation including challenges related to sample size, model design and interpretability, and the lack of robust multicenter validation set. Material and methods: In this article, we will review the concepts of radiomics and radiogenomics and their potential applications in rectal cancer. Conclusion: Radiologists should be aware of the basic concepts, benefits, pitfalls, and limitations of new radiomic and radiogenomics techniques to achieve a balanced interpretation of the results.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

DOE OSTI2023

Localized keyhole pore prediction during laser powder bed fusion via multimodal process monitoring and X-ray radiography

Systematic fault detection and control during laser powder bed fusion (L-PBF) has been a long-standing objective for system manufacturers and researchers in the additive manufacturing (AM) industry. This manuscript investigates a data fusion approach for detection of keyhole porosity formation during laser irradiation of Ti-6Al-4V substrates by concurrent recording of thermally induced optical emission measured using both off-axis and coaxial photodiode sensors, and acoustic emission. Subsurface defect formation was monitored via high-speed synchrotron X-ray imaging at 20,000 frames per second, enabling temporal registration of keyhole pore formation events to the monitoring signals at a resolution of 50 µs. We developed data fusion machine learning (ML) models for localized prediction of keyhole pore formation at various time scales ranging from 0.5 ms to 2 ms. The signal segments were featurized using two independent approaches: (1) power spectral density (PSD) and (2) highly comparative time series analysis (HCTSA) framework. The extracted features from different sensor modalities were fused together to construct a multimodal feature space and sequential feature selection was used to determine the most informative features for training the ML models. The predictive performance was evaluated for three classifying algorithms: Support Vector Machine (SVM), K-Nearest Neighbor (KNN), and Gaussian Naive Bayes (GNB). As a result, pore formation events were predicted with up to 0.95 F1-score, 1.0 recall and 0.94 accuracy. The most heavily weighted features indicate that model performance is chiefly governed by the acoustic monitoring signal, with a secondary contribution from the optical emission sensors.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Structure–Transport Relationships of Water–Organic Solvent Co-transport in Carbon Molecular Sieve (CMS) Membranes

We explore the effects of the carbon molecular sieve (CMS) microstructure on the separation performance and transport mechanism of water–organic mixtures. Specifically, we utilize PIM-1 dense films and integrally skinned asymmetric hollow fiber membranes as polymer precursors for the CMS materials. The PIM-1 membranes were pyrolyzed under several different pyrolysis atmospheres (argon, carbon dioxide, and diluted hydrogen gas) and at multiple pyrolysis temperatures. Detailed gas physisorption measurements reveal that membranes pyrolyzed under 4% H 2 and CO 2 had broadened ultramicropore distributions (pore diameter <7 Å) compared to Ar pyrolysis, and pyrolysis under CO 2 increased ultramicropore volume and broadened micropore distributions at increased pyrolysis temperatures. Gravimetric water and p-xylene sorption and diffusion measurements reveal that the PIM-1-derived CMS materials are more hydrophilic than other CMS materials that have been previously studied, which leads to sorption-diffusion estimations showing water-selective permeation. Water permeation in the vapor phase, pervaporation, and liquid-phase hydraulic permeation reveal that the isobaric permeation modes (vapor permeation and pervaporation) are reasonably well predicted by the sorption-diffusion model, whereas the hydraulic permeation mode is significantly underpredicted (>250×). Conversely, the permeation of p-xylene is well predicted by the sorption-diffusion model in all cases. The collection of pore size analysis, vapor sorption and diffusion, and permeation in different modalities creates a picture of a combined transport mechanism in which water–under high transmembrane pressures–permeates via a Poiseuille-style mechanism, whereas p-xylene solutes in the mixture permeate via sorption-diffusion.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2016

Microfluidic volumetric flow determination using optical coherence tomography speckle: An autocorrelation approach

Functional modalities of Optical Coherence Tomography (OCT) based on speckle analysis are emerging in the literature. We propose a simple approach to the autocorrelation of OCT signal to enable volumetric flow rate differentiation, based on decorrelation time. Our results show that this technique could distinguish flows separated by 3 μl/min, limited by the acquisition speed of the system. We further perform a B-scan of gradient flow inside a microchannel, enabling the visualization of the drag effect on the walls.

42 ENGINEERING↗

NASA NTRS1973

Performance of statistical energy analysis

Statistical energy analysis (SEA) methods have been developed for high frequency modal analyses on random vibration environments. These SEA methods are evaluated by comparing analytical predictions to test results. Simple test methods are developed for establishing SEA parameter values. Techniques are presented, based on the comparison of the predictions with test values, for estimating SEA accuracy as a function of frequency for a general structure.

Davis, R. F.↗

NASA NTRS1977

On scaling techniques

An introductory review of the principles of scaling with emphasis on ride quality work is presented. It will be divided into six parts as follows: (1) definition of scaling, (2) scope and goals of scaling, (3) scaling techniques (with emphasis on rating scale, magnitude estimation procedures and cross-modality matching), (4) laboratory vs. field studies, (5) multivariate analysis; and (6) selected references.

Source record↗

NASA NTRS1978

Glasses in the Luna 24 core and petrogenesis of ferrobasalts

Modal abundance and major- and minor-element chemical analysis of homogeneous, non-agglutinitic mare and non-mare glasses from the Luna 24 drill core show that most glasses can be related to known rock types. Mare glasses include: brown glass identical in composition to the fine-grained low-Mg VLT basalt; green glass which might be related to a coarser-grained ferrogabbro; a high-K green glass; and a high-Ti orange glass. Highland glass compositions include Highland basalt, gabbroic anorthosite, and pure anorthosite (i.e. plagioclase); minor Fra Mauro-type glass may also be present. It is apparent that fractional crystallization of some primitive basaltic magma occurred at Mare Crisium producing a chemically evolved ferrobasalt and related glasses. An early, high-Mg basin fill, as represented by the olivine vitrophyres, may be the parent magma. Subsequent near-surface fractionation produced a multiply-saturated liquid that finally erupted as the ferrobasalt flows sampled by Luna 24.

Norman, M.↗

NASA NTRS1982

Some statistical performance characteristics of the 'ITD' modal identification algorithm

Performance characteristics of the Ibrahim time-domain algorithms are examined on a statistical basis. The method uses multiple free-response measurements from a test structure directly in the time domain, and displays varying accuracy, with the strongly excited modes identified most accurately and the weakly excited modes least accurately. Sets of computer-generated free-response functions for a simple 1-mode model are used to study the identification performance for several basic changes in the modal characteristics of the data, the user-selectable analysis constants, and the level of superimposed noise. Results indicate the existence of a direct and often linear effect of noise on the scatter of identified parameters, and good identification is maintained at the 1% noise level down to the point in frequency when only 1/4-cycle of data is analyzed.

Pappa, R. S.↗

NASA NTRS1988

Optimal placement of tuning masses for vibration reduction in helicopter rotor blades

Methods are presented for the reduction of helicopter rotor blade vibration through a formal mathematical optimization technique determination of optimum tuning mass sizes and locations; these are used as design variables that are systematically changed to achieve low values of shear without large mass penalty. Matrix expressions are obtained for the modal shaping parameter and modal shear amplitude that are required for FEM structural analysis of the blade as well as the optimization formulation. Sensitivity derivatives are also obtained. Three different optimization strategies are developed and tested.

Pritchard, Jocelyn I.↗

NASA NTRS1987

Flying Qualities Research Challenges

Traditional flying qualities requirements for airplane dynamics are based on airplane modal response characteristics derived from linear small-perturbation analysis. These requirements are supported by a large experimental data base. The challenge to the flying qualities community is to demonstrate how flying qualities, the control system and aircraft configuration are still closely linked. This is evident in the definition of flying qualities and, as far as pilots are concerned, that flying qualities are still the measure of overall design success.

Steven M Sliwa↗