Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Ions Separations”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 991 records · Page 55
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Correlating the influence of porosity, tortuosity, and mass loading on the energy density of LiNi 0.6 Mn 0.2 Co 0.2 O 2 cathodes under extreme fast charging (XFC) conditions

Extreme fast charging capabilities along with high energy density of Li-ion batteries are the key factors to increase the adoption of electric vehicles while eliminating the problem of range anxiety. The U.S Department of Energy has a goal of <12 min charging time with energy density of > 200 Wh kg -1 . A combined improvement in the electrode architecture, electrolyte properties, and separator membrane is necessary to achieve this goal. Cells with thin electrodes are capable of extreme fast charging at the expense of low energy density and high cost. Electrode engineering can maximize energy density. In this work, the influence of porosity, mass loading and charging protocols on capacity and energy density and electrode kinetics are investigated under extreme fast charging conditions. Increasing the mass loading from 11.5 mg cm -2 to 25 mg cm -2 compromises the rate performance due to the mass transport limitation and underutilization of thick electrodes. Furthermore, reducing the electrode porosity from 50% to 35% improves the rate performance ascribed to shorter Li ion diffusion length. Symmetric cells are cycled to verify the performance of the half cells, suggesting that Li metal plating is the rate limiting step under high current density.

25 ENERGY STORAGE↗
DOE OSTI2022

Thick Electrode Design for Facile Electron and Ion Transport: Architectures, Advanced Characterization, and Modeling

The demand for lithium ion batteries continues to expand for powering applications such as portable electronics, grid-scale energy storage, and electric vehicles. As the application requirements advance, the innovation of lithium ion batteries toward higher energy density and power output is required. Along with the investigation of new materials, an important strategy for increasing battery energy content is to design electrodes with high areal loading to minimize the fraction of nonactive materials such as current collectors, separators, and packaging components, resulting in significant gains in energy content and the reduction of the system-level cost. However, the adoption of thick high areal loading electrodes has been impeded by sluggish charge transport and mechanical instability. With conventional slurry cast electrodes, battery function significantly deteriorates with increases in electrode thickness due to high cell polarization and the incomplete utilization of active materials. Thus, a consideration of approaches that facilitate an understanding and eventual adoption of high-loading electrodes is warranted to enable the deliberate advancement of next-generation batteries. Herein, this Account considers three aspects critical to the science and technology of thick high-loading electrodes. The first discussion covers recent approaches to the design and fabrication of high-loading electrodes. Ensuring electrical contact throughout the electrode is accomplished through the manipulation of conductive additives or using a conductive scaffold within the electrode. Ion transport can be facilitated through electrode design and fabrication approaches that deliberately control the electrode porosity and tortuosity. Second, advanced characterization methodologies are presented as the ability to determine the origins of transport limitations provide the insight needed to deliberately approach future designs. Spectroscopic and diffraction methods have been used to characterize the 2D and 3D pore structure and composition of the electrodes. Furthermore, operando methods that yield spatially and temporally resolved information regarding the progression of the electrochemical reaction are highlighted. The third aspect considered is the utilization of modeling. Physically based continuum models linked with the results of experimental characterization have been demonstrated and then allow the rapid simulation of a variety of deliberate electrode designs and their impacts on functional electrochemistry. Variables relevant to the designs can be tested by the model under a series of use conditions to identify those of most promise for a specific application. Finally, an outlook on future opportunities for high-loading battery electrode research is provided to inform and entice practitioners in the field to pursue these important directions of inquiry.

25 ENERGY STORAGE↗
DOE OSTI2025

Influence of Water, Vacuum, and Temperature on Surface Conditions of a Zeolite‐based Molecular Sieve

Molecular sieves such as zeolite-based materials are ubiquitous in industrial separation processes. However, there is a significant gap in understanding the surface properties and adsorption mechanisms for commercial zeolites, as most research focuses on pure zeolite powders rather than industrially relevant forms. Here, this work addresses this gap in understanding by employing advanced characterization techniques, including positron annihilation spectroscopy, X-ray diffraction, scanning electron microscopy, X-ray fluorescence spectroscopy, X-ray photoelectron spectroscopy, liquid nitrogen sorption, and Fourier-transform infrared spectroscopy, to investigate the adsorption and desorption behavior of water in commercial zeolite 13X. Our research reveals insights into the pore-filling mechanisms, the impact of material binders on adsorption properties, and the dynamics of hydration and drying processes for zeolites. Monitoring changes on a minute scale allowed the distinction between fast and slow processes leading to sample drying. The identification of positronium bound to Na + ions indicated that water molecules remain in the vicinity of Na + ions after air-drying zeolite 13X. These findings highlight the importance of various environmental conditions in restoring zeolite properties to baseline after hydration, with significant implications for optimizing industrial processes. This work sets the direction for further research aimed at developing more efficient and robust separation techniques.

Beads Binder↗
DOE OSTI2022

Rational design of photosynthetic reaction center protein maquettes

New technologies for efficient solar-to-fuel energy conversion will help facilitate a global shift from dependence on fossil fuels to renewable energy. Nature uses photosynthetic reaction centers to convert photon energy into a cascade of electron-transfer reactions that eventually produce chemical fuel. The design of new reaction centers de novo deepens our understanding of photosynthetic charge separation and may one day allow production of biofuels with higher thermodynamic efficiency than natural photosystems. Recently, we described the multi-step electron-transfer activity of a designed reaction center maquette protein (the RC maquette), which can assemble metal ions, tyrosine, a Zn tetrapyrrole, and heme into an electron-transport chain. Here, we detail our modular strategy for rational protein design and show that the intended RC maquette design agrees with crystal structures in various states of assembly. A flexible, dynamic apo-state collapses by design into a more ordered holo-state upon cofactor binding. Crystal structures illustrate the structural transitions upon binding of different cofactors. Spectroscopic assays demonstrate that the RC maquette binds various electron donors, pigments, and electron acceptors with high affinity. We close with a critique of the present RC maquette design and use electron-tunneling theory to envision a path toward a designed RC with a substantially higher thermodynamic efficiency than natural photosystems.

09 BIOMASS FUELS↗
DOE OSTI2021

4D Imaging of ZnO-Coated Nanoporous Al 2 O 3 Aerogels by Chemically Sensitive Ptychographic Tomography: Implications for Designer Catalysts

The 3D chemical structure (4D spectromicroscopy) of nanoporous Al 2 O 3 aerogels coated with ZnO by atomic layer deposition (ALD) was studied by multienergy scanning transmission X-ray microscopy. These materials are representative of a class of designer catalysts in which the nanoporous support is prepared separately from the active catalyst material, which is subsequently introduced by ALD, thereby allowing independent optimization of the morphology, chemistry, and spatial distribution of the support and catalyst. The samples studied were prepared by Ga ion and Xe plasma focused ion beam (FIB) milling as well as drop casting from water suspension. Zn L and Al K edge spectra of six samples with three different ZnO loadings were measured to investigate how loading and different sample preparation methods affect the 3D distribution of the ZnO and Al 2 O 3 . Scanning transmission X-ray microscopy (STXM) and ptychographic imaging at two energies each at the Zn L 3 and Al K edge were measured. The ptychography data were analyzed by using the SHARP reconstruction code to generate quantitative 2D chemical maps of the Al 2 O 3 and the ZnO. The STXM and ptychography maps were then measured at a sequence of tilt angles, covering up to 160° of rotation. The 3D structure of the ZnO and Al 2 O 3 was derived from the tilt series data by tomographic reconstruction using a compressed sensing algorithm. A twodimensional spatial resolution (half-period) of 6 nm, measured by Fourier ring correlation, and a 3D spatial resolution (half-period) of 9 nm, measured by Fourier shell correlation, were achieved when using the COSMIC beamline at the Advanced Light Source (ALS). The results show that for all of the ZnO loadings studied there is nonuniform coverage of the ZnO on the Al 2 O 3 aerogel framework. In addition, we found that both FIB methods create sample artifacts, although the distortion was less with Xe plasma than Ga ion FIB.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Nanoporous weakly coordinating anionic frameworks (Final Technical Report)

Under this award, we synthesized and characterized new weakly coordinating, anionic covalent organic frameworks. The motivation was to expand the class of covalent organic frameworks though the introduction of the first weakly coordinating anionic ones. The significance of the weakly coordinating anionic character of these frameworks is associated with the character of the counter (metal) cations in their pores. Those counter-cations, due to the inability to effectively coordinate to the pore walls, have a “naked”, and thus highly electrophilic, Lewis acidic character. Such properties are expected to translate to a number of interesting physical properties that can be potentially used for a range of energy-relevant applications. One of these applications is gas adsorption, separation, and storage. The electrophilic, Lewis acidic character of the counter-cations are expected to strongly bind to gas molecules entering the pores leading to higher gas sorption capacities. Other applications include heterogeneous catalysis, ion exchange, and solid state ion conduction. Within the project we explored a range of chemical blocks, and tested synthesis conditions to polymerize these building blocks to form the target materials. In particular, we focused on materials with group 15 elements like phosphorus in the oxidation state +5 and the coordination number 6, that have a formal -1 charge. The synthesis of such materials is challenging because its success depends on the absence of residual monomeric and oligomeric side-products in the pores, and the absence of significant framework interpenetration. Crystalline forms of these materials require sufficient reversibility of the polymerization reaction (which is difficult to achieve because group 15 elements like P tend to make strong covalent bonds with neighbored elements), as well as suitable polymerization rates that prevent the formation of kinetically controlled products. We had success with the preparation of anionic porous organic frameworks with anionic building blocks containing P(V)O6 octahedra synthesized through Yamamoto coupling reactions. These materials are non-crystalline because of the irreversible nature of the Yamamoto coupling reaction, but show porosity. The porosity and surface area can be significantly increased by co-reaction with electrostatically neutral co-reactants. Very high porosity and surface areas can be achieved when the materials are washed with hydrochloric acid. This method is commonly used to free products from Yamamoto coupling reactions from by-products. Indeed, this method removed by products from the pores of our materials, however it also led to the hydrolysis of the PO6 octahedra to form pending phosphonic acid groups (-PO3H)-groups in the frameworks (PA-POFs) which was actually not desired. Nonetheless, these materials showed high CO2 sorption capacities. In addition, they show extremely high (actually record) sorption capacities for the removal of a range of common micropollutants such as bisphenol A (BPA) and 4-nitrophenol in water. BPA is a wide-spread organic pollutant and a known endocrine disruptor. The maximum adsorption capacity of BPA at equilibrium is found to be as high as 3,366 mg g-1 by Langmuir adsorption model, which is more than 10 times greater than peer materials. The polymer also rapidly removes various other organic micropollutants with more than 90% removal efficiencies. In addition, the PA-POF material can be regenerated at least five times by mild washing using methanol without significant loss in removal efficiency. This is significant advantage over commonly used activated carbon materials (that are in Brita water faucet filters, for example). Comparison studies showed that only materials with the phosphonate groups show extreme sorption although the number of PA group is actually small according to solid state NMR and EDX data. More research would be needed to investigate why this is (a possibility is that the phosphonate groups have a multiplying effect in which a PA-induced initial adsorption leads to the adsorption of much more adsorbate). The extreme sorption capabilities can also be visually seen when colored adsorbates such as 4-nitrophenol are used, as the adsorption of the nitrobenzene leads to the decoloration of the solution. We have produced three short videos that illustrate the sorption capabilities compared to two peer materials (activated carbon from dismantled Brita water filters, and a electrostatically neutral, chemically related, porous organic polymer, respectively).

36 MATERIALS SCIENCE↗
DOE OSTI2022

Electronic structures on swollen hydrogels

This document describes a conformable substrate that includes a hydrogel having adhesion-promoting moieties, said adhesion-promoting moieties comprising one or more catechol groups. The conformable substrate includes an array of microelectrodes bonded to the hydrogel by the adhesion-promoting moieties via the one or more catechol groups. This document also describes a method for transfer printing of an electronic structure to a hydrogel. The method includes the steps of coating a donor substrate with a film of polyacrylic acid, crosslinking the film of polyacrylic acid in a solution comprising divalent ions, patterning a microelectrode array onto the crosslinked film of polyacrylic acid, laminating an adhesive hydrogel substrate onto the donor substrate coated by the crosslinked film of polyacrylic acid comprising the patterned microelectrode array, and separating the crosslinked film of polyacrylic acid from the donor substrate in a monovalent solution.

Bettinger, Christopher J.↗
DOE OSTI2025

Coupling Interfacial Redox‐Reactions with In Situ Proton Generation for the Photoelectrochemical Separation of Rare‐Earth Elements

Abstract A dual‐function photoelectrochemical (PEC) separation system is demonstrated for rare‐earth element (REE) recovery. The sustainable release of the captured REEs is promoted through the synergistic integration of a redox‐reaction for electrostatic repulsion, and in situ proton generation for ion‐exchange, all driven by photoelectrochemistry. The platform consists of a redox‐copolymer, poly(ferrocenylpropyl methacrylamide‐ co ‐methacrylic acid) (P(FPMAm‐ co ‐MAA)) (PFM), conjugated with carbon nanotubes (CNTs) and coated onto titanium dioxide nanorods (TNRs). The (PFM‐CNT)/TNR spontaneously adsorbs up to 214.2 mg of Yttrium/g PFM by ion‐exchange, and demonstrates broad applicability for other REEs. The adsorbed REEs are released through the PEC oxidation of ferrocene (Fc) to ferrocenium (Fc + ), and the simultaneous PEC water splitting reactions at the TNRs that protonate the carboxylate binding groups. This dual photoelectrochemically‐driven mechanism for REE release is investigated by in situ pH measurements, as well as vibrational and X‐ray photoelectron spectroscopy. Through PEC approaches, a 68.8% reduction in energy consumption during REE recovery has been achieved compared to purely electrochemical systems, with a regeneration efficiency close to 100%. For NdFeB magnets from waste hard disk drives, Nd and Dy recovery efficiencies of 59.2 and 61.1% are achieved. The dual‐functionality of these copolymer PEC systems offers a sustainable platform for modulating critical element recovery.

Cho, Ki‐Hyun [Department of Chemical and Biomolecu↗
DOE OSTI2021

Mapping glyceride species in biodiesel by high-temperature gas chromatography combined with chemical ionization mass spectrometry.

Accurate and comprehensive identification of residual glycerides in biodiesel is an important part of the fuel characterization, due to the impact of glycerides on the fuel physicochemical properties. However, analysis of bound glycerol in biodiesel samples faces challenges due to lack of readily available standards of structurally complex glyceride species in non-traditional biodiesel feedstocks, and a risk of misannotation in the presence of impurities in gas chromatographic separations. Here we evaluate methane and isobutane chemical ionization – single quadrupole mass spectrometry combined with high temperature gas chromatography separations for mapping monoacylglycerols, diacylglycerols and triacylglycerols in biodiesel. Unlike the electron impact ionization which produces mostly in-source fragments, isobutane chemical ionization spectra of tetramethylsilyl (TMS) derivatized monoacylglycerols and diacylglycerols are dominated by molecular ions and M-SiO(CH3)3+ ions, which provide important diagnostic information. We demonstrate the utility of isobutane chemical ionization in identifying structurally complex glycerolipid standards as well as species in biodiesel samples from different plant and animal feedstocks.

biodiesel, chemcial ionization mass spectrometry↗
DOE OSTI2026

Microcanonical Kinetics of Water-Mediated Proton Transfer in 4ABAH + ·(H 2 O) n = 4–6 Clusters (ABA = Aminobenzoic Acid): A Model System for Size-Dependent Relaxation to Ergodic Behavior

Here, we leverage the unique properties of the 4ABAH + · (H 2 O) n clusters (ABA = 4-aminobenzoic acid, n = 4−6) to quantitatively address how a finite, isolated system evolves into an ergodic condition starting from localized arrangements in configuration space. This system adopts two distinct structural isomers in which water molecules cluster around the cationic centers of its two protomers with widely separated positive charge centers. These isomers arise from excess proton attachment to either the acid (O) or amino (N) group on opposite sides of the benzene ring. Both forms are captured and kinetically trapped using cryogenic ion methods and then selectively vibrationally excited through their mutually exclusive IR bands involving NH and OH stretching fundamentals. Because the IR excitation lies below the water binding energy, the system can evolve to explore slow, rare events that lead to the interconversion between the two isomers. The rates of these intracluster reactions are determined by using a pump−probe scheme involving ∼5 ns IR pump and UV probe lasers. The rates occur on the microsecond time scale, leading to steady state populations of the isomers, thus revealing the cluster size-dependent fractionation between the two species at microcanonical equilibrium. The steady state distributions are correlated with the expected trend in the cluster size-dependent reaction energetics, which are in turn consistent with changes in the relative densities of states of the two species. These results thus provide an unusually clear example in which complex, protic-solvent-mediated chemical transformations are captured within a finite system at a precisely determined internal energy.

Rana, Abhijit [Yale Univ., New Haven, CT (United S↗
DOE OSTI2023

TaO x electron transport layers for CO 2 reduction Si photocathodes

Electron transport layers (ETLs) used as components of photocathodes for light-driven CO 2 reduction (CO 2 R) in aqueous media should have good electronic transport, be stable under CO 2 R conditions, and, ideally, be catalytically inert for the competing hydrogen evolution reaction (HER). Here, using planar p-Si (100) as the absorbing material, we show that TaO x satisfies all three of the above criteria. TaO x films were synthesized by both pulsed laser deposition (PLD) and radio-frequency (RF) sputtering. In both cases, careful control of the oxygen partial pressure during growth was required to produce ETLs with acceptable electron conductivity. p-Si/TaO x photocathodes were interfaced with ca. 10 nm of a CO 2 R catalyst: Cu or Au. Under front illumination with simulated AM 1.5G in CO 2 -saturated bicarbonate buffer, we observed, for both metals, faradaic efficiencies for CO 2 R products of ~50% and ~30% for PLD TaO x and RF sputtered TaO x , respectively, at photocurrent densities up to 8 mA cm -2 . p-Si/TiO 2 /Cu photocathodes were also evaluated but produced mostly H 2 (>97%) due to reduction of the TiO 2 to Ti metal under CO 2 R conditions. In contrast, a dual ETL photocathode (p-Si/TiO 2 /TaO x /Cu) was selective for CO 2 R, which suggests a strategy for separately optimizing selective charge collection and the stability of the ETL/water interface. The maximum photovoltage obtained with p-Si/TaO x /Cu devices was 300 mV which was increased to 430–460 mV by employing ion implantation to make pn + -Si/TaO x /Cu structures. Photocathodes with RF sputtered TaO x ETLs are stable for CO 2 R for at least 300 min. In conclusion, techno-economic analysis shows that the reported system, if scaled, could allow for an economically viable production of feedstocks for chemical synthesis under the adoption of specific CO 2 credit schemes, thus becoming a significant component of carbon-neutral manufacturing.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Simulated thermonuclear performance of auto-magnetizing helical liner MagLIF target implosions

Magnetized liner inertial fusion (MagLIF) implosions on the Z accelerator require magnetization of the fuel to reduce thermal conduction losses of energy from the laser-preheated deuterium fusion fuel to the surrounding liner material. While external field coils traditionally used to axially magnetize MagLIF targets are limited to 10–20 T (or perhaps ∼ 30 T with technological development), calculations suggest that higher axial magnetic fields would improve thermal insulation of the fuel and improve MagLIF target performance. We present results from three-dimensional radiation-magnetohydrodynamic simulations of MagLIF implosions employing auto-magnetizing helical liners composed of discrete metallic helical conduction paths separated by electrically insulating material. These simulated auto-magnetizing (AutoMag) liners produce axial magnetic fields >30 T inside the fusion fuel prior to implosion. Simulations indicate that higher thermonuclear yields and burn-averaged fuel ion temperatures are attained for implosions using AutoMag liners compared to standard MagLIF implosions. Comparable implosion morphology is evident in synthetic x-ray images of AutoMag–MagLIF and standard MagLIF implosions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Modulating surface acoustic wave generation through superconductivity

Surface acoustic waves (SAWs), with their five orders-of-magnitude slower propagation velocity, allow for considerably shorter wavelengths at the same frequency compared to electromagnetic waves. The short wavelengths allow for device miniaturization and on-chip integration. The generic design of these devices involves piezoelectric substrates with comb-like arrays of Al or Au electrodes known as interdigitated transducers (IDTs) deposited on the surface. However, Al and Au both have shortcomings at the cryogenic temperatures required for quantum applications, namely, the formation of two-level systems and the lack of superconductivity perpetuating Ohmic losses, respectively. In this work, SAWs are generated in the high-MHz to low-GHz range using niobium nitride (NbN) interdigitated transducers and Bragg reflectors. We demonstrate the fabrication of acoustic devices through photolithography and reactive ion etching. The sharp transition between superconducting and normal states and the corresponding change in SAW transmission allows for fine control of the “on” (superconducting) and “off” (normal) states of NbN, with a ΔT = 1 K separating the transmission minimum and maximum. We demonstrate a 16× difference in transmission between the “on” and “off” states of the device. The SAW transmission behavior mirrors the change in resistance of NbN at its T c . These findings open up new possibilities for the integration of NbN SAW resonators into existing quantum architectures based on NbN and a method for adjusting transmission properties independent of applied voltage.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Oscillatory redox behavior in oxides: Cyclic surface reconstruction and reactivity modulation via the Mars–van Krevelen mechanism

The breaking of translational symmetry at oxide surfaces gives rise to coordinatively unsaturated cations/anions and surface restructuring—key factors that govern surface reactivity. Using direct in situ environmental transmission electron microscopy (TEM) observations along with atomistic modeling, we report oscillatory redox behavior in CuO under H 2 , where cyclic surface reconstruction and reactivity modulation occur via the Mars–van Krevelen (MvK) mechanism. We observe self-switching between oxygen-rich and oxygen-deficient surface reconstructions, alternately activating and deactivating the surface for H 2 O formation. During periods of chemical inactivity, the oxygen-deficient surface undergoes slow reoxidation via lattice oxygen diffusing from subsurface and bulk reservoirs, restoring the active oxygen-rich surface termination. The inherent disparity in chemical activity among undercoordinated surface ions, along with sluggish subsurface-to-surface oxygen replenishment, drives this oscillatory redox cycle, modulating H2-induced loss of lattice oxygen at the surface and its delayed replenishment from the subsurface. This creates spatiotemporally separated redox steps at the oxide surface. The phenomena and atomistic insights presented here have significant implications for manipulating the surface reactivity of oxides by tuning the separation of these redox steps.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Mixed ionic and electronic conductor for solid state battery

Disclosed are electrochemical devices, such as lithium ion battery electrodes, lithium ion conducting solid-state electrolytes, and solid-state lithium ion batteries including these electrodes and solid-state electrolytes. Also disclosed are methods for making such electrochemical devices. Also disclosed are composite electrodes for solid state electrochemical devices. The composite electrodes include one or more separate phases within the electrode that provide electronic and ionic conduction pathways in the electrode active material phase.

Sakamoto, Jeffrey↗
DOE OSTI2021

Multifunctional Separator Allows Stable Cycling of Potassium Metal Anodes and of Potassium Metal Batteries

Here, this is the first report of a multifunctional separator for potassium-metal batteries (KMBs). Here, double-coated tape-cast microscale AlF 3 on polypropylene (AlF 3 @PP) yields state-of-the-art electrochemical performance: symmetric cells are stable after 1000 cycles (2000 h) at 0.5 mA cm –2 and 0.5 mAh cm –2 , with 0.042 V overpotential. Stability is maintained at 5.0 mA cm –2 for 600 cycles (240 h), with 0.138 V overpotential. Postcycled plated surface is dendrite-free, while stripped surface contains smooth solid electrolyte interphase (SEI). Conventional PP cells fail rapidly, with dendrites at plating, and “dead metal” and SEI clumps at stripping. Potassium hexacyanoferrate(III) cathode KMBs with AlF 3 @PP display enhanced capacity retention (91% at 100 cycles vs 58%). AlF 3 partially reacts with K to form an artificial SEI containing KF, AlF 3 , and Al 2 O 3 phases. The AlF 3 @PP promotes complete electrolyte wetting and enhances uptake, improves ion conductivity, and increases ion transference number. The higher of K + transference number is ascribed to the strong interaction between AlF 3 and FSI – anions, as revealed through 19 F NMR. The enhancement in wetting and performance is general, being demonstrated with ester- and ether-based solvents, with K-, Na-, or Li- salts, and with different commercial separators. In full batteries, AlF 3 prevents Fe crossover and cycling-induced cathode pulverization.

NMB↗
DOE OSTI2021

Correlation of the Structure with Performance in MEH-PPV/dPS Thin Films Illuminated during Processing

Thin films containing conjugated polymers have been used in a wide array of optoelectronic devices, and much research has focused on the conformation of the conjugated polymer as a key aspect to tuning the performance of the resulting devices. White light exposure has been studied as a post-processing method to alter the film’s morphology and photoluminescence (PL) in systems composed of poly[2-methoxy-5-(2-ethylhexyloxy)-1,4-phenylenevinylene] (MEH-PPV) and polystyrene (PS). To date, there have been few studies that correlate the changes in the depth profile with the PL performance of MEH-PPV/PS films. This study is designed to address this gap in knowledge. Thin films of MEH-PPV/dPS annealed above the glass transition temperatures (T g ) in an illuminated environment led to lower PL than that found in annealed samples that are not illuminated. However, at higher MEH-PPV loading in the blend film, the extent of variation of PL with illumination diminished. Additionally, time-of-flight secondary ion mass spectrometry and small-angle neutron scattering document the three-dimensional morphology of the films under illumination conditions, which are correlated with the changes in PL. Illumination during annealing compressed MEH-PPV-rich layers in the thin film blends at low loadings of MEH-PPV (below 10 wt %) but resulted in significant in-plane phase separation at higher loadings (above 15 wt %). Both changes increase interchain interactions and lower the PL of the illuminated samples. The changes in the depth profile significantly alter the PL of the films, while the in-plane phase separation affected the optoelectronic properties to a lesser degree. This work, therefore, provides insights into how illumination and film composition can be utilized to predictably alter the structure and optoelectronic performance of conjugated polymer blend films.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Modeling Coupled Chemo-Mechanical Behavior of Randomly Oriented NMC811 Polycrystalline Li-Ion Battery Cathodes

This paper develops a three-dimensional, transient, chemo-mechanical model that predicts the performance of single secondary particle Li-ion battery cathodes. The secondary particles are composed of numerous (approximately 60) randomly oriented single-crystal primary particles. The model incorporates concentration-dependent and anisotropic material properties. As much as possible, electrochemical, transport, and structural properties for crystalline NMC811 (Li x Ni 0.8 Mn 0.1 Co 0.1 O 2 ) are taken from prior publications. Weak Van der Waals bonding between primary particles is modeled empirically using a spring analogy, which enables local primary-particle separations (disintegration) and subsequent reattachments. The model fully couples Li diffusion and the mechanical response. Results include predictions of local Li-concentrations and stresses. High stresses are found near grain boundaries, especially when the lattice orientations are greatly misaligned. Particle separations are characterized in terms of a damage parameter. The model is used to predict the effects of design and operating conditions, including charge/discharge rates, cycling scenarios, and particle sizes.

25 ENERGY STORAGE↗