Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Ignition”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 991 records · Page 55
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Measurement of Spray Chamber Ignition Delay and Cetane Numbers for Aviation Turbine Fuels

Experiments using pure compounds, National Jet Fuels Combustion Program (NJFCP) test fuels, and commercial jet fuels were conducted to demonstrate the equivalence of the indicated cetane number (ICN) and derived cetane number (DCN) for jet fuels. The calibrated range for ICN was also extended to lower cetane number (CN) values (5 to 35) to allow CN quantification for jet fuel synthetic blending components (SBCs) with low CN. ICN and DCN were shown to be highly correlated for values above about 30. This study presents the most comprehensive comparison of these two methods published to date. Because of the importance of low-volume test methods for early-stage SBC production process development, we demonstrated that ICN and DCN can be accurately measured with 15 mL of fuel, well below 40 to 100 mL required by standard methods. ICN or DCN is important for jet fuels because fuels with lower CN are more prone to lean blowout (LBO), an undesirable operational failure in a jet engine. Comparing data on a fuel-to-air ratio (Φ) at LBO for the NJFCP fuels shows similar linear correlations for ICN and DCN. Ignition delay measurements at lower-pressure and higher-temperature conditions may be more directly relevant to LBO. At 675 °C, 0.5 MPa, and a global Φ of roughly 0.68, ignition delay time correlations to LBO were similar to those produced from DCN and ICN. A much weaker correlation was obtained with a global Φ value of 0.34.

09 BIOMASS FUELS↗
DOE OSTI2020

Lightning Interferometry Uncertainty, Beam Steering Interferometry, and Evidence of Lightning Being Ignited by a Cosmic Ray Shower

Abstract We present an uncertainty analysis on correlation‐based time delay estimate, the basis for broadband lightning interferometry. A normal interferometry would yield much higher uncertainties than the theoretically predicted lower bound due to finite correlation window lengths. However, if the signals are aligned in time, the uncertainties approach the lower bound and can be used to indicate the interferometric uncertainties. Based on this, we introduce a beam steering interferometry technique. It first estimates a direction centroid for the lightning sources with a normal interferometry and computes the time delays among the signals. It then shifts the raw data with the time delays to align the signals roughly in time and reprocess the aligned signals. It finally pushes the reprocessed results to their correct positions, based on the time delays estimated in the first step. We apply this technique on a fast positive breakdown (FPB) process that started a normal intracloud lightning. The FPB process is shown to have a much more complex structure and development than a normal interferometry would provide. More importantly, from both interferometric and polarization analyses, the FPB appears to be ignited by a cosmic ray shower (CRS). We estimate the radio frequency strength and frequency content related to a presumed CRS in a thunderstorm electric field and find that they are in agreement with the observations. We examine the electric field effect of the CRS front and find that it could raise the field above the threshold for positive breakdown and is capable of igniting the FPB (and the lightning).

Shao, Xuan‐Min↗
DOE OSTI2014

Time-resolved compression of a capsule with a cone to high density for fast-ignition laser fusion

The advent of high-intensity lasers enables us to recreate and study the behaviour of matter under the extreme densities and pressures that exist in many astrophysical objects. It may also enable us to develop a power source based on laser-driven nuclear fusion. Achieving such conditions usually requires a target that is highly uniform and spherically symmetric. Here we show that it is possible to generate high densities in a so-called fast-ignition target that consists of a thin shell whose spherical symmetry is interrupted by the inclusion of a metal cone. Using picosecond-time-resolved X-ray radiography, we show that we can achieve areal densities in excess of 300 mg cm -2 with a nanosecond-duration compression pulse -- the highest areal density ever reported for a cone-in-shell target. Such densities are high enough to stop MeV electrons, which is necessary for igniting the fuel with a subsequent picosecond pulse focused into the resulting plasma.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2012

Precision equation-of-state measurements on National Ignition Facility ablator materials from 1 to 12 Mbar using laser-driven shock waves

A large uncertainty in the design of ignition capsules for use in the National Ignition Campaign (NIC) is the ablator equation of state. In this article, we report equation-of-state measurements for two candidate NIC ablator materials, glow-discharge polymer (GDP), and germanium-doped GDP. These materials were driven to pressures of 1 to 12 Mbar using laser-driven shock waves. Hugoniot measurements were obtained using the impedance matching technique with an α-quartz standard. This article presents the first kinematic measurements in the high-pressure fluid regime for these materials, which show to be in close agreement with Livermore equation-of-state model predictions.

Barrios, M. A.↗
DOE OSTI2012

High Performance Imaging Streak Camera for the National Ignition Facility

An x-ray streak camera platform has been characterized and implemented for use at the National Ignition Facility. The camera has been modified to meet the experiment requirements of the National Ignition Campaign and to perform reliably in conditions that produce high EMI. A train of temporal UV timing markers has been added to the diagnostic in order to calibrate the temporal axis of the instrument and the detector efficiency of the streak camera was improved by using a CsI photocathode. The performance of the streak camera has been characterized and is summarized in this paper. The detector efficiency and cathode measurements are also presented.

Opachich, Y. P.↗
DOE OSTI2012

Sensitivity study of ignition capsule implosion performance on the hard x-ray spectral distribution of hohlraum

The paper investigates theoretically the sensitivities of ignition capsule implosion performance on the hard x-ray spectral distribution of hohlraum. In the simulation, the hohlraum radiation is represented by a Planckian spectrum for the main drive plus a gaussian bump centered at energy E{sub c} for preheating x-rays. Simulation results show that with the increasing of center energy E{sub c}, the Atwood number at the fuel-ablator interface increases rapidly due to the preheating and expanding of the inner undoped CH layer. The growing of Atwood number indicates the hydrodynamic instability (HI) growth and mixing at this interface. On the other hand, the increasing of E{sub c} results in a large density gradient scale length of ablation front and stabilizes the HI growth at ablation front. The changes of the hard x-ray spectrum have significant influences on other important implosion parameters including the ablator mass remaining, shock timing, implosion velocity, and yield as well. High-precision results on the hard x-ray spectral distribution of hohlraum are thus critical for optimizing the ignition capsule design to limit the HI growth.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2013

Finite Mach number spherical shock wave, application to shock ignition

A converging and diverging spherical shock wave with a finite initial Mach number M{sub s0} is described by using a perturbative approach over a small parameter M{sub s}{sup −2}. The zeroth order solution is the Guderley's self-similar solution. The first order correction to this solution accounts for the effects of the shock strength. Whereas it was constant in the Guderley's asymptotic solution, the amplification factor of the finite amplitude shock Λ(t)∝dU{sub s}/dR{sub s} now varies in time. The coefficients present in its series form are iteratively calculated so that the solution does not undergo any singular behavior apart from the position of the shock. The analytical form of the corrected solution in the vicinity of singular points provides a better physical understanding of the finite shock Mach number effects. The correction affects mainly the flow density and the pressure after the shock rebound. In application to the shock ignition scheme, it is shown that the ignition criterion is modified by more than 20% if the fuel pressure prior to the final shock is taken into account. A good agreement is obtained with hydrodynamic simulations using a Lagrangian code.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2015

On the study of threshold intensity dependence on the gain and loss processes in laser induced spark ignition of molecular hydrogen

In the present work, a numerical analysis is performed to investigate the comparative contribution of the mechanisms responsible for electron gain and losses in laser spark ignition and plasma formation of H{sub 2}. The analysis considered H{sub 2} over pressure range 150 -3000 torr irradiated by a Nd:YAG laser radiation at wavelengths 1064 and 532 nm with pulse length 5.5 ns. The study based on a modified electron cascade model by one of the authors which solves numerically the time dependent Boltzmann equation as well as a set of rate equations that describe the rate of change of the excited states population. The model includes most of the physical processes that might take place during the interaction. Computations of The threshold intensity are performed for the combined and separate contribution of each of the gain and loss processes. Reasonable agreement with the measured values over the tested pressure range is obtained only for the case of the combined contribution. Basing on the calculation of the electron energy distribution function, the determined relations of the time evolution of the electrons density for selected values of the tested gas pressure region revealed that photo-ionization of the excited states could determine the time of electron generation and hence spark ignition. Collisional ionization contributes to this phenomenon only at the high pressure regime. Loss processes due to electron diffusion, vibrational excitation are found to have significant effect over examined pressure values for the two applied laser wavelengths.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2016

Ignition and monitoring technique for plasma processing of multicell superconducting radio-frequency cavities

In this study, an in-situ plasma processing technique has been developed at the Spallation Neutron Source (SNS) to improve the performance of the superconducting radio-frequency (SRF) cavities in operation. The technique uses a low-density reactive neon-oxygen plasma at room-temperature to improve the surface work function, to help remove adsorbed gases on the RF surface and to reduce its secondary emission yield. SNS SRF cavities are six-cell elliptical cavities and the plasma typically ignites in the cell where the electric field is the highest. This article will detail a technique that was developed to ignite and monitor the plasma in each cell of the SNS cavities.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2017

Simultaneous diagnosis of radial profiles and mix in NIF ignition-scale implosions via X-ray spectroscopy

In a National Ignition Facility implosion, hydrodynamic instabilities may cause the cold material from the imploding shell to be injected into the hot-spot (hot-spot mix), enhancing the radiative and conductive losses, which in turn may lead to a quenching of the ignition process. The bound-bound features of the spectrum emitted by high-Z ablator dopants that get mixed into the hot-spot have been previously used to infer the total amount of mixed mass; however, the typical errorbars are larger than the maximum tolerable mix. We present in this paper an improved 2D model for mix spectroscopy which can be used to retrieve information on both the amount of mixed mass and the full imploded plasma profile. By performing radiation transfer and simultaneously fitting all of the features exhibited by the spectra, we are able to constrain self-consistently the effect of the opacity of the external layers of the target on the emission, thus improving the accuracy of the inferred mixed mass. The model's predictive capabilities are first validated by fitting simulated spectra arising from fully characterized hydrodynamic simulations, and then, the model is applied to previously published experimental results, providing values of mix mass in agreement with previous estimates. Finally, we show that the new self consistent procedure leads to better constrained estimates of mix and also provides insight into the sensitivity of the hot-spot spectroscopy to the spatial properties of the imploded capsule, such as the in-flight aspect ratio of the cold fuel surrounding the hotspot.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2018

The I-Raum: A new shaped hohlraum for improved inner beam propagation in indirectly-driven ICF implosions on the National Ignition Facility

Recent work in indirectly-driven inertial confinement fusion implosions on the National Ignition Facility has indicated that late-time propagation of the inner cones of laser beams (23° and 30°) is impeded by the growth of a “bubble” of hohlraum wall material (Au or depleted uranium), which is initiated by and is located at the location where the higher-intensity outer beams (44° and 50°) hit the hohlraum wall. The absorption of the inner cone beams by this “bubble” reduces the laser energy reaching the hohlraum equator at late time driving an oblate or pancaked implosion, which limits implosion performance. In this article, we present the design of a new shaped hohlraum designed specifically to reduce the impact of this bubble by adding a recessed pocket at the location where the outer cones hit the hohlraum wall. This recessed pocket displaces the bubble radially outward, reducing the inward penetration of the bubble at all times throughout the implosion and increasing the time for inner beam propagation by approximately 1 ns. This increased laser propagation time allows one to drive a larger capsule, which absorbs more energy and is predicted to improve implosion performance. The new design is based on a recent National Ignition Facility shot, N170601, which produced a record neutron yield. The expansion rate and absorption of laser energy by the bubble is quantified for both cylindrical and shaped hohlraums, and the predicted performance is compared.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2018

Capsule physics comparison of National Ignition Facility implosion designs using plastic, high density carbon, and beryllium ablators

Indirect drive implosion experiments on the National Ignition Facility (NIF) [E. I. Moses et al., Phys. Plasmas 16, 041006 (2009)] have now tested three different ablator materials: glow discharge polymer plastic, high density carbon, and beryllium. How do these different ablators compare in current and proposed implosion experiments on NIF? What are the relative advantages and disadvantages of each? This paper compares these different ablator options in capsule-only simulations of current NIF experiments and potential future designs. The simulations compare the impact of the capsule fill tube, support tent, and interface surface roughness for each case, as well as all perturbations in combination. According to the simulations, each ablator is impacted by the various perturbation sources differently, and each material poses unique challenges in the pursuit of ignition on NIF.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2018

Advancing the capability of the gated laser-entrance-hole imager on the National Ignition Facility

A new configuration based on the recent off-line calibrations of the gated laser entrance hole diagnostic on the National Ignition Facility provides 4-8 interleaved frames per experiment using the standard two frame sensor settings. Since its implementation, the new design has greatly increased the data return for hundreds of experiments at the National Ignition Facility. The large quantity of images from a variety of physics campaigns has revealed information on plasma evolution in hohlraums.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2018

Time resolved detection of two-plasmon decay using three-halves harmonic emission on the National Ignition Facility

Supra-thermal (>100 keV) electrons generated by laser plasma interactions can be detrimental to the performance of ignition experiments conducted on the National Ignition Facility (NIF). On a NIF shot, the amount of electrons is estimated by measuring the hard X-rays passing through the hohlraum wall. The primary sources of hot electrons in a hohlraum are Stimulated Raman Scattering (SRS) and two plasmon decay (TPD). While SRS is well diagnosed on the NIF, there has been no diagnosis of TPD. Here we have designed and implemented a new diagnostic to characterize the time history of TPD on the NIF. The instrument provides a time resolved measurement of the 3/2 ω harmonic emission which is indicative of the presence of TPD. We describe the diagnostic setup, calibration, and the preliminary results obtained on NIF hohlraum experiments. Finally, we find evidence of a correlation between measured hard X-rays generated from the hot electron bremsstrahlung and the TPD emission.

47 OTHER INSTRUMENTATION↗
DOE OSTI2018

Impact ignition and combustion of micron-scale aluminum particles pre-stressed with different quenching rates

Pre-stressing aluminum (Al) particles by annealing and quenching alters dilatational strain and is linked to increased particle reactivity. The quenching rate associated with pre-stressing is a key parameter affecting the final stress state within the Al particle, with faster quenching rates theoretically favoring a higher, more desirable stress state. Micron scale Al particles are annealed to 573 K, then quenched at different rates (i.e., 200 and 900 K/min), mixed with bismuth oxide (Bi2O 3 ), and the Al + Bi2O 3 mixtures are examined under low-velocity, drop-weight impact conditions. Both quenching rates showed increased impact ignition sensitivity (i.e., between 83% and 89% decrease in ignition energy). However, the slower quenching rate showed a 100% increase in pressurization rate compared to untreated particles, while the faster quenching rate showed a 97% increase in peak pressure, indicating that these two quenching rates affect Al particles differently. Surprisingly, synchrotron X-ray diffraction data show that the 200 K/min quenched particles have a higher dilatational strain than the untreated particles or the 900 K/min quenched particles. Results are rationalized with the help of a simple mechanical model that takes into account elastic stresses, creep in the alumina shell, and delamination of shell from the core. The model predicts that Al powder quenched at 200 K/min did not experience delamination. In contrast, Al quenched at 900 K/min did not have creep but does have delamination, and under impact, delamination led to major fracture, greater oxygen access to the core, and significant promotion of reaction. Thus, the increase in quenching rate and shell-core delamination are more important for the increase in Al reactivity than pre-stressing alone.

42 ENGINEERING↗
DOE OSTI2019

Pushered single shell implosions for mix and radiation trapping studies using high-Z layers on National Ignition Facility

Pushered Single Shells (PSSs) are another approach to Inertial Confinement Fusion implosions that employ high-Z materials in the innermost capsule layer (pusher) as a means to enhance radiation trapping and lower core ignition requirements. However, adding high-Z materials can also increase losses due to mix, provide extra tamping, and make the capsule emission opaque to x-ray diagnostics. The first PSS implosions performed on the National Ignition Facility use plastic ablators with a germanium (Ge) dopant as a high-Z surrogate in the pusher to isolate the effects of high-Z mix and radiation trapping without changing tamping. Using a 2-shock laser pulse, the PSS implosions are designed and symmetrized to reach 3.7 keV core temperatures. A low concentration (2.8%) Ge dopant is added to the innermost layer, and the resulting effects on mix and x-ray opacity are observed. The method of separated reactants is used to infer information about mixing between the deuterated plastic pusher and the capsule fill gas (25% tritium) from the resulting nuclear DT reactions. Radiation transport is studied via capsule emission x-ray spectroscopy and imaging. Both nuclear and x-ray data corroborate the hypothesis that the addition of Ge strongly affects the mix region through radiation losses but has a minimal effect on the core and the warm, unmixed regions. Simulations using diffusive and turbulent mix models agree qualitatively with data, but quantitative agreement may require hybrid mix models that can model the transitional regime between turbulence and diffusion. Simulations matching the observables show increased core radiation trapping when Ge is added.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Experimental study of hot electron generation in shock ignition relevant high-intensity regime with large scale hot plasmas

In the shock ignition (SI) laser fusion scheme, hot electrons generated by the laser spike pulse can either preheat the fuel or strengthen the ignition shock, depending on the hot electron characteristics. We conducted a planar target experiment on the OMEGA-EP laser facility and characterized the temperature and total energy of hot electrons generated from a kilojoule-class 100-ps infrared (IR) or a 1-ns ultraviolet (UV) laser interacting with a large (L n ~330-450 μm) and hot (T e ~1-2 keV) coronal plasma at the SI-relevant intensities (~10 16 W/cm 2 ). The IR laser converts ~2.5% energy into hot electrons with T hot ~ 60–90 keV, while the UV laser couples 0.8% ± 0.7% energy into T hot =27 ± 9 keV hot electrons. The IR-produced hot electrons yield five times higher Cu Kα emission than the UV case, confirming the higher electron conversion efficiency with the IR laser. The low energy conversion from the UV laser to hot electrons may be due to the refraction of the off-normal incident laser in the large coronal plasma. These findings are the first comparisons of hot electron generation between the IR and UV pulses at kilojoule scales in SI-relevant large-scale plasmas. The findings may expand the SI design space to include IR lasers as the possible spike lasers.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Carbon ablator areal density at fusion burn: Observations and trends at the National Ignition Facility

For inertial confinement fusion experiments, the pusher is composed of a high-density deuterium tritium cyrogenic fuel layer and an ablator, often made of carbon. In an ideal, no-mix implosion, increasing the areal density of the pusher transfers more pressure to the hot spot and increases the hot spot confinement time. There has been a lack of knowledge about the final compressed state of the ablator for implosions at the National Ignition Facility. 14 MeV fusion neutrons inelastically scattering on the remaining carbon ablator excites a nuclear metastable state that emits a prompt 4.4 MeV gamma ray. The gamma reaction history diagnostic data, when reduced by a new data analysis technique, can isolate and measure the carbon gamma rays, which are proportional to the areal density of the ablator during fusion burn. The trends over many National Ignition Facility campaigns show that the ablator areal density is weakly sensitive to the maximum shell velocity, the cold fuel radius, the ablator mass remaining, or the laser picket intensity. Controlled parameter scans reveal that, for specific campaigns, ablator compression has a strong dependence on laser coast time, high Z dopants, and the laser drive foot duration. Using a model of the compressed ablator density profile reveals that the greatest variation of the ablator areal density comes from its thickness, with highly compressed, thin layers having high areal density values. The compression and thickness of the ablator are other metrics that designers should understand to differentiate the types of capsule degradation and maximize the inertial confinement fusion performance.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗