SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Materials illustrating a presentation on electromechanical actuation programs (EMA) are presented. The development history is outlined. Space shuttle flight control systems and the advantages of EMAS, and EMA technology status and development requirements are outlined.
The effective use of simulation from issuance of the request for proposal through conduct of a flight test program for the XV-15 Tilt Rotor Research Aircraft is discussed. From program inception, simulation complemented all phases of XV-15 development. The initial simulation evaluations during the source evaluation board proceedings contributed significantly to performance and stability and control evaluations. Eight subsequent simulation periods provided major contributions in the areas of control concepts; cockpit configuration; handling qualities; pilot workload; failure effects and recovery procedures; and flight boundary problems and recovery procedures. The fidelity of the simulation also made it a valuable pilot training aid, as well as a suitable tool for military and civil mission evaluations. Simulation also provided valuable design data for refinement of automatic flight control systems. Throughout the program, fidelity was a prime issue and resulted in unique data and methods for fidelity evaluation which are presented and discussed.
Results of comparisons of predictions of aerodynamic performance, longitudinal trim, and reaction control jet interaction with data from the initial Shuttle flight are presented. The Shuttle's control surfaces are described, and it is noted that the flight plan contained no provisions for maneuvering capability tests. Wind tunnel testing totaling 35,000 hr were used to replace graduated flight testing, and calculations were made to allow for nonsimulated structural deformation, flowfield parameters, and profile drag. The goal was to desensitize the flight control system with respect to the aerodynamics by adding variations to the predictions. Lift/drag agreed well above Mach 1, while lower drag was encountered below Mach 1. Trim characteristics were predicted accurately between Mach 2-10, and less than satisfactorily outside that range. Discrepancies were also observed for jet interaction effects for the aft yaw jets at Mach numbers greater than 10.
This paper presents several optimal maneuvers of supersonic aircraft in a vertical plane. The general dimensionless equations of motion are derived and the computation of the optimal trajectories are carried out using the aerodynamics and engine characteristics of a light-weight fighter called the supercruiser. Because of the normalizing of the control variables, namely, the load factor and the thrust-to-weight ratio, the results applied to any supersonic aircraft. The optimality of the singular thrust control and the optimal junction of different subarcs are discussed. The proposed method of computing the optimal trajectory is very efficient and makes explicit the selection of the optimal control. The technique should be useful for performance assessment of supersonic aircraft with potential for implementation of onboard flight control system.
An overview of the aerodynamic performance, longitudinal trim, and control surface effectiveness as developed from the second Shuttle flight is presented, along with comparisons with preflight predictions. The Orbiter enters the atmosphere at Mach 29 and descends through all the Mach speeds until touchdown. Control mechanisms for the Orbiter are outlined, noting the lessening of angle of attack as the terminal configuration is reached. Methods of developing the wind tunnel predictions are reviewed, including performance in different altitudes and speed regimes, and the impetus to decouple the flight control system from aerodynamics with respect to uncertainties. Preflight predictions agreed well with the lift/drag ratio above Mach 1, but higher L/D was exhibited than predicted below Mach 1. A deficiency in the wind tunnel environment was concluded for the inaccuracies in the predictions for hypersonic trim characteristics.
A study of the Shuttle Orbiter approach and landing conditions is summarized. The causes of observed PIO-like flight deficiencies are listed, and possible corrective measures are examined. Closed-loop pilot/vehicle analyses are described, and a description is given of path-attitude stability boundaries. The latter novel approach is found to be of great value in delineating and illustrating the basic causes of this multiloop pilot control problem. It is shown that the analytical results are consistent with flight test and fixed-base simulation. Conclusions are drawn concerning possible improvements in the Shuttle Orbiter/Digital Flight Control System.
The present investigation is concerned with the development of a better pilot modelling technique via optimal control theory, taking into account concepts concerning 'pilot rating' considered by Neal and Smith (1970). The investigation conducted by Neal and Smith had the objective to provide data on the effects of Flight Control System dynamics and to develop a design criterion capable of pinpointing pilot problem areas encountered in performing a given task. Neal and Smith devised a 'pilot-in-the-loop' analysis capable of showing problem areas in pitch attitude tracking. Unfortunately the employed method has some drawbacks. The current investigation attempts, therefore, to provide an alternate approach which makes use of an optimal-control pilot model. An optimal control model (OCM) had been discussed by Kleinman et al. (1970). It is shown that the alternate approach, based on the OCM, offers some distinct advantages.
An automatic flight control systems design methods for aircraft that have complex characteristics and operational requirements, such as the powered lift STOL and V/STOL configurations are discussed. The method is effective for a large class of dynamic systems that require multiaxis control and that have highly coupled nonlinearities, redundant controls, and complex multidimensional operational envelopes. The method exploits the possibility of linearizing the system over its operational envelope by transforming the state and control. The linear canonical forms used in the design are described, and necessary and sufficient conditions for linearizability are stated. The control logic has the structure of an exact model follower with linear decoupled model dynamics and possibly nonlinear plant dynamics. The design method is illustrated with an application to a helicopter autopilot design.
Software error data of major recent Digital Flight Control Systems Development Programs. The report summarizes the data, compare these data with similar data from previous surveys and identifies trends and disciplines to improve software reliability.
Translational state estimation in terminal area operations, using a set of commonly available position, air data, and acceleration sensors, is described. Kalman filtering is applied to obtain maximum estimation accuracy from the sensors but feasibility in real-time computations requires a variety of approximations and devices aimed at minimizing the required computation time with only negligible loss of accuracy. Accuracy behavior throughout the terminal area, its relation to sensor accuracy, its effect on trajectory tracking errors and control activity in an automatic flight control system, and its adequacy in terms of existing criteria for various terminal area operations are examined. The principal investigative tool is a simulation of the system.
Flight control system (FCS) reliability is discussed in terms of sensors, computers and actuators. The servo/actuation bottleneck is discussed. FCS survivability is considered. Preliminary survivability issues. A Grumman study vehicle, R-14, and YF-16 aircraft configurations are studied. Goals of control are reviewed.
This paper examines the application of variable structure control theory to the design of a flight control system for the AV-8A Harrier in a hover mode. The objective in variable structure design is to confine the motion to a subspace of the total state space. The motion in this subspace is insensitive to system parameter variations and external disturbances that lie in the range space of the control. A switching type of control law results from the design procedure. The control system was designed to track a vector velocity command defined in the body frame. For comparison purposes, a proportional controller was designed using optimal linear regulator theory. Both control designs were first evaluated for transient response performance using a linearized model, then a nonlinear simulation study of a hovering approach to landing was conducted. Wind turbulence was modeled using a 1052 destroyer class air wake model.
Studies carried out by McGough and Swern (1981, 1983) are summarized. In these studies, an avionics processor was simulated and a series of fault injection experiments was carried out to determine the degree of fault latency in a redundant flight control system that employed comparison monitoring as the exclusive means of failure detection. A determination was also made of the fault coverage of a typical self-test program. The summary presented stresses that a self-test program should be designed to capitalize on the hardware mechanization of the processor. If this is not done, subtests tend to repeatedly exercise the same hardware components while neglecting to exercise a substantial proportion of the remainder. It is also pointed out that fault latency is relatively independent of both the length and instruction mix of a program. A significant difference is found in fault coverage assessed using pin-level and gate-level fault models.
Translational state estimation in terminal area operations, using a set of commonly available position, air data, nd acceleration sensors, is described. Kalman filtering is applied to obtain maximum estimation occuracy from the sensors but feasibility in real-time computations requires a variety of approximations and devices aimed at minimizing the required computation time with only negligible loss of accuracy. Accuracy behavior throughout the terminal area, its relation to sensor accuracy, its effect on trajectory tracking errors and control activity in an automatic flight control system, and its adequacy in terms of existing criteria for various terminal area operations are examined. The principal investigative tool is a simulation of the system. Previously announced in STAR as N83-29193
Some of the lessons learned during the development of the Space Shuttle descent flight control system (FCS) are reviewed. Examples confirm the importance for requirements definition, systems level analyses, and testing. In sounding these experiences may have implication for future designs or suggest the discipline required in this engineering art.
The Air Transportation Technology Program at Princeton University, a program emphasizing graduate and undergraduate student research, proceeded along six avenues during the past year: investigation of fuel use characteristics of general aviation aircraft, experimentation with an ultrasonic altimeter, single pilot instrument flight, application of fiber optics in flight control systems, voice recognition inputs for navigation/communication receiver tuning, and computer aided aircraft design.
The application of distributed processing, fiber optics, and hardware redundancy to collecting airstream data in Princeton's digitally controlled Variable-Response Research Aircraft (VRA) is described. Microprocessor controlled instrumentation packages in each wingtip of the aircraft collect angle of attack and sideslip data in digital form; after scaling, filtering, and calibrating the data, they send it to the aircraft's microprocessor Digital Flight Control System (micro-DFCS) via digital fiber optic data links. Each wingtip's package is independent of the other; therefore, the system has dual hardware redundancy. The fiber optic link design is presented as well as a description of the calibration and communications software.
A brief analytic exposition is presented to illustrate a central principle in flexible mode control, some of the pertinent pilot centered requirements are listed and discussed. The desired features of the control methodology are exposed and the methodology to be used is selected. The example Boeing supplied characteristics are discussed and approximated with a reduced order model and a simplified treatment of unsteady aerodynamics. The closed loop flight control system design follows, along with first level assessments of resulting handling and ride quality characteristics. Some of these do not meet the postulated requirements and remain problems to be solved possibly by further analysis or future simulation.