Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FUSELAGE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 991 records · Page 55

Full-Scale Transport controlled Impact Demonstration

The controlled impact demonstration (CID) test of a transport aircraft took place on December 1, 1984, crashing at a prepared site on Rogers Dry Lakebed, Edwards Air Force Base, California. The demonstration was a setback for the antimisting kerosene (AMK) researchers. The impact conditions, considerably different from the planned scenario, exposed large quantities of degraded AMK and hydraulic fluid and caused unexpectedly hot ignition sources, bulk loss of fuel from the right wing, airflow patterns over the wings and fuselage that were untested on AMK, and fuel intrusion into the lower fuselage. The test was much more severe than planned and is generally considered to be unrepresentative of the type of survivable crash that would benefit from AMK. Ninety-seven percent of the sensors on the fuselage and wing structure, seats, dummies, restraint systems, galley, and bins were active at impact. A wealth of sensor data was collected from this once-in-a-lifetime research test. The flight data recorder experiments on board were also generally successful.

Hayduk, R. J.↗

Gust response of hingeless rotors

The gust response of a coupled hingeless rotor-fuselage system is studied in both hover and forward flight. Each rotor blade undergoes flap bending, lag bending, and torsional deflections. The blades are discretized into beam elements, each with fifteen nodal degrees of freedom. The fuselage is permitted three translational (vertical, longitudinal, and lateral) and two rotational (pitch and roll) degrees of freedom. The formulation considers a three-dimensional gust field wherein each gust velocity component can have an arbitrary variation in space and time. Aerodynamic loads are obtained using quasisteady strip theory. Wake-induced effects are introduced through dynamic inflow modeling. Dynamic stall and reverse flow effects are also included. Equations governing the rotor-fuselage gust response are linearized about the vehicle propulsive trim state and the blade steady-state defected positions, and solved by time integration. The effects of several parameters on the helicopter gust response are illustrated, including dynamic inflow, lag stiffness, forward speed, gust profile, gust penetration rate, and gust velocity direction.

Bir, G. S.↗

Propeller-induced structure-borne noise - Laboratory-based test apparatus

A potentially important source of structure-borne interior noise transmission in advanced turboprop aircraft is the impingement of the propeller wake/vortex on downstream aerodynamic surfaces. The expected levels of propeller wake/vortex-induced structure-borne noise transmission are not known nor can they be determined with present-day technology. A test apparatus has been designed, built and calibrated for the purposes of studying propeller-induced, structure-borne noise transmission in prototypical aircraft structures. The principal approach to the test apparatus design was to provide a physical means of separating the airborne and structure-borne noise components so that the structure-borne noise transmission response could be studied directly without airborne noise contamination. This was accomplished by housing the receiving fuselage structure in an acoustic shield fitted with a wing-to-fuselage acoustic seal. Initial evaluation of the wing-to-fuselage acoustic seal indicates adequate airborne noise isolation to allow direct study of structure-borne noise transmission.

Unruh, J. F.↗

A comparison of the structureborne and airborne paths for propfan interior noise

In the present comparative study of aircraft interior noise levels due to airborne and structureborne paths for a given propeller source, a structure model is used that treats the fuselage interior as a rectangular cavity with five rigid walls; the sixth, or fuselage sidewall, is a stiffened panel. The wing is modeled as a simple beam carried into the fuselage by a large, discrete stiffener representing the carry-through structure. Comparisons are made on the basis of interior noise over a range of propeller rotational frequencies at a fixed thrust. It is found that the relative importance of the structural and airborne paths is highly dependent on the structural parameters.

Eversman, W.↗

Over-the-wing propeller

This invention is an aircraft with a system for increasing the lift drag ratio over a broad range of operating conditions. The system positions the engines and nacelles over the wing in such a position that gains in propeller efficiency is achieved simultaneously with increases in wing lift and a reduction in wing drag. Adverse structural and torsional effects on the wings are avoided by fuselage mounted pylons which attach to the upper portion of the fuselage aft of the wings. Similarly, pylon-wing interference is eliminated by moving the pylons to the fuselage. Further gains are achieved by locating the pylon surface area aft of the aircraft center of gravity, thereby augmenting both directional and longitudinal stability. This augmentation has the further effect of reducing the size, weight and drag of empennage components. The combination of design changes results in improved cruise performance and increased climb performance while reducing fuel consumption and drag and weight penalties.

Johnson, Joseph L., Jr.↗

Research investigation of helicopter main rotor/tail rotor interaction noise

Acoustic measurements were obtained in a Langley 14 x 22 foot Subsonic Wind Tunnel to study the aeroacoustic interaction of 1/5th scale main rotor, tail rotor, and fuselage models. An extensive aeroacoustic data base was acquired for main rotor, tail rotor, fuselage aerodynamic interaction for moderate forward speed flight conditions. The details of the rotor models, experimental design and procedure, aerodynamic and acoustic data acquisition and reduction are presented. The model was initially operated in trim for selected fuselage angle of attack, main rotor tip-path-plane angle, and main rotor thrust combinations. The effects of repositioning the tail rotor in the main rotor wake and the corresponding tail rotor countertorque requirements were determined. Each rotor was subsequently tested in isolation at the thrust and angle of attack combinations for trim. The acoustic data indicated that the noise was primarily dominated by the main rotor, especially for moderate speed main rotor blade-vortex interaction conditions. The tail rotor noise increased when the main rotor was removed indicating that tail rotor inflow was improved with the main rotor present.

Fitzgerald, J.↗

The prediction of helicopter tail rotor noise on the flight path

Experimental measurements on a model scale helicopter in a wind tunnel have shown that the levels radiated in the direction of flight are strongly dependent on the fuselage angle to the mean flow. Here a theoretical model is derived to explain these measurements using unsteady thickness noise as the principle source mechanism. The model includes the effect of fuselage wake turbulence which is convected through only the lower sector of the rotor disk. This causes spectral peaks which do not occur at blade passing frequencies, but rather at frequencies associated with convected flow inhomogeneities. The results are compared with measurements and show good agreement over a range of fuselage angles and mean flow speeds.

Glegg, Stewart A. L.↗

Phase 4 static tests of the J-97 powered, external augmentor V/STOL model at the NASA, Ames Research Center, November 1983

A large-scale, ejector-lift V/STOL Model, powered by a J-97 engine, was tested at the NASA Ames Research Center Outdoor Aerodynamics Research Facility. The model incorporated the external augmentor concept developed by DHC. Since the first test at Ames in 1979, the fuselage augmentor nozzle array has been redesigned with a larger pitch and notched nozzles instead of plain slot nozzles. Thrust augmentation of the ejector as measured at Ames Research Center was lower than that measured in the DHC laboratory. It is believed that this difference is due to the high temperature of the primary jet flow as compared to the DHC blown-down rig. An ejector-lift/vectored thrust configuration was also included in the recent tests. This is an arrangement where the fuselage augmentor is shortened in the chordwise direction and the extra thrust is generated with a vectorable, ventral nozzle. In free air the shortened fuselage augmentor produced the same augmentation as the long augmentor. In ground proximity, at a height of 27 in, and with zero pitch angle, a negative ground effect was measured equal to 6.5 percent of the free-air lift.

Garland, D. B.↗

Flight measured downwash of the QSRA

Several reports have been written on the performance of the Quiet Short-Haul Research Aircraft, which shows the advantages of upper-surface blowing or the propulsive-lift wing as it applies to lift, maneuverability, and short takeoff and landing. This high lift generation at low speeds results in substantial downwash, especially in the low-aft fuselage tail position. The high T-tail of the Quiet Short-Haul Research Aircraft minimizes the undesirable downwash effects from the propulsive-lift wing. Queries from Department of Defense agencies and industry for quantitative values prompted a series of flight-measured downwash tests at the high T-tail and the low aft fuselage position. The results are presented in a summarized format, showing downwash, Delta epsilon/Delta a, for both locations. As would be expected, downwash increases for increased power and USB flap settings. The downwash is greater in the low aft-fuselage position as compared to the high T-tail area.

Eppel, Joseph C.↗

CAP-TSD analysis of the F-15 aircraft

The F-15 fighter aircraft was modeled using Computational Aeroelasticity Program - Transonic Small Disturbance (CAP-TSD). The complete aircraft was modeled including the wing, stabilator, flow through inlets, and fuselage body. CAP-TSD was used to make static pressure runs for Mach numbers of 0.8, 0.9, 0.95 and 1.2. The angle of attack for these runs ranged from 0 to 5 degs. The CAP-TSD program showed good agreement between the computed fuselage and wing pressures and the measured wind tunnel pressures. Including the fuselage and inlets in the CAP-TSD analysis is important and improves the correlation of wing pressures with test data.

Pitt, Dale M.↗

High speed turboprop aeroacoustic study (single rotation). Volume 1: Model development

A frequency-domain noncompact-source theory for the steady loading and volume-displacement (thickness) noise of high speed propellers has been developed and programmed. Both near field and far field effects have been considered. The code utilizes blade surface pressure distributions obtained from three-dimensional nonlinear aerodynamic flow field analysis programs as input for evaluating the steady loading noise. Simplified mathematical models of the velocity fields induced at the propeller disk by nearby wing and fuselage surfaces and by angle-of-attack operation have been developed to provide estimates of the unsteady loading imposed on the propeller by these potential field type interactions. These unsteady blade loadings have been coupled to a chordwise compact propeller unsteady loading noise model to provide predictions of unsteady loading noise caused by these installation effects. Finally, an analysis to estimate the corrections to be applied to the free-field noise predictions in order to arrive at the measurable fuselage sound pressure levels has been formulated and programmed. This analysis considers the effects of fuselage surface reflection and diffraction together with surface boundary layer refraction. The steady loading and thickness model and the unsteady loading model have been verified using NASA-supplied data for the SR-2 and SR-3 model propfans. In addition, the steady loading and thickness model has been compared with data from the SR-6 model propfan. These theoretical models have been employed in the evaluation of the SR-7 powered Gulfstream aircraft in terms of noise characteristics at representative takeoff, cruise, and approach operating conditions. In all cases, agreement between theory and experiment is encouraging.

Whitfield, C. E.↗

Flight measured downwash of QSRA

Several reports have been written on the performance of the Quiet Short-Haul Research Aircraft, which shows the advantages of upper-surface blowing or the propulsive-lift wing as it applies to lift, maneuverability, and short takeoff and landing. This high lift generation at low speeds results in substantial downwash, especially in the low-aft fuselage tail position. The high T-tail of the Quiet Short-Haul Research Aircracft minimizes the undesirable downwash effects from the propulsive-lift wing. Queries from Department of Defense agencies and industry for quantitative values prompted a series of flight-measured downwash tests at the high T-tail and the low aft fuselage position. The results are presented in a summarized format, showing downwash, Delta epsilon/Delta a, for both locations. As would be expected, downwash increases for increased power and USB flap settings. The downwash is greater in the low aft-fuselage position as compared to the high T-tail area.

Eppel, Joseph C.↗

Pneumatic vortical flow control at high angles of attack

The injection of thin, high-momentum jets of air into the fuselage forebody boundary layers of the F-18 aircraft is explored numerically as a means of controlling the onset of fuselage vortices and of generating yaw control forces. The study was carried out for an angle of attack of 30 deg with symmetrical and asymmetrical blowing configurations. One-sided blowing results in a strongly asymmetrical flow pattern in the fore portion of the fuselage, leading to a net lateral force.

Tavella, Domingo A.↗

Test results for composite specimens and elements containing joints and cutouts

A program was conducted to develop the technology for joints and cutouts in a composite fuselage that meets all design requirements of a large transport aircraft for the 1990s. An advanced trijet derivative of the DC-10 was selected as the baseline aircraft. Design and analysis of a 30-foot-long composite fuselage barrel provided a realistic basis for the test effort. The primary composite material was Hexcel F584 resin on 12 K IM6 fiber, in tape and broadgoods form. Fiberglass broadgoods were used in E-glass and S-glass fiber form in the cutout region of some panels. Additionally, injection-molded chopped graphite fiber/PEEK was used for longeron-to-frame shear clips. The test effort included four groups of test specimens, beginning with coupon specimens of mono-layer and cross-piled laminates, progressing through increasingly larger and more complex specimens, and ending with two 4- by 5-foot curved fuselage side panels. One of the side panels incorporated a transverse skin splice, while the second included two cabin window cutouts.

Sumida, P. T.↗

Noise transmission properties and control strategies for composite structures

A study of several component technologies required to apply active control techniques to reduce interior noise in composite aircraft structures is described. The mechanisms of noise transmission in an all composite, large-scale, fuselage model are studied in an experimental program and found similar to mechanisms found in conventional aircraft construction. Two primary conditions of structural acoustic response are found to account for the dominant interior acoustic response. A preliminary study of active noise control in cylinders used piezoceramic actuators as force inputs for a simple aluminum fuselage model. These actuators provided effective control for the same two conditions of noise transmission found in the composite fuselage structure. The use of piezoceramic actuators to apply force inputs overcomes the weight and structural requirements of conventional shaker actuators. Finally, in order to accurately simulate these types of actuators in a cylindrical shell, two analytical models are investigated that apply either in-plane forces or bending moments along the boundaries of a finite patch. It is shown that the bending model may not be as effective as the force model for exciting the low order azimuthal modes that typically dominate the structural acoustic response in these systems. This result will affect the arrangement and distribution of actuators required for effective active control systems.

Silcox, Richard J.↗

Developments in impact damage modeling for laminated composite structures

Damage tolerance is the most critical technical issue for composite fuselage structures studied in the Advanced Technology Composite Aircraft Structures (ATCAS) program. The objective here is to understand both the impact damage resistance and residual strength of the laminated composite fuselage structure. An understanding of the different damage mechanisms which occur during an impact event will support the selection of materials and structural configurations used in different fuselage quadrants and guide the development of analysis tools for predicting the residual strength of impacted laminates. Prediction of the damage state along with the knowledge of post-impact response to applied loads will allow for engineered stacking sequencies and structural configurations; intelligent decisions on repair requirements will also result.

Dost, Ernest F.↗

An overview of the crash dynamics failure behavior of metal and composite aircraft structures

An overview of failure behavior results is presented from some of the crash dynamics research conducted with concepts of aircraft elements and substructure not necessarily designed or optimized for energy absorption or crash loading considerations. Experimental and analytical data are presented that indicate some general trends in the failure behavior of a class of composite structures that includes fuselage panels, individual fuselage sections, fuselage frames, skeleton subfloors with stringers and floor beams without skin covering, and subfloors with skin added to the frame stringer structure. Although the behavior is complex, a strong similarity in the static/dynamic failure behavior among these structures is illustrated through photographs of the experimental results and through analytical data of generic composite structural models.

Carden, Huey D.↗

Computational analysis of methods for reduction of induced drag

The purpose of this effort was to perform a computational flow analysis of a design concept centered around induced drag reduction and tip-vortex energy recovery. The flow model solves the unsteady three-dimensional Euler equations, discretized as a finite-volume method, utilizing a high-resolution approximate Riemann solver for cell interface flux definitions. The numerical scheme is an approximately-factored block LU implicit Newton iterative-refinement method. Multiblock domain decomposition is used to partition the field into an ordered arrangement of blocks. Three configurations are analyzed: a baseline fuselage-wing, a fuselage-wing-nacelle, and a fuselage-wing-nacelle-propfan. Aerodynamic force coefficients, propfan performance coefficients, and flowfield maps are used to qualitatively access design efficacy. Where appropriate, comparisons are made with available experimental data.

Janus, J. M.↗