Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FRACTURE PROPERTIES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 991 records · Page 55

Failure Predictions of Out-of-Autoclave Sandwich Joints with Delaminations under Flexure Loads

An analysis and a test program was conducted to investigate the damage tolerance of composite sandwich joints. The joints contained a single circular delamination between the face-sheet and the doubler. The coupons were fabricated through out-of-autoclave (OOA) processes, a technology NASA is investigating for joining large composite sections. The four-point bend flexure test was used to induce compression loading into the side of the joint where the delamination was placed. The compression side was chosen since it tends to be one of the most critical loads in launch vehicles. Autoclave cure was used to manufacture the composite sandwich sections, while the doubler was co-bonded onto the sandwich face-sheet using an OOA process after sandwich panels were cured. A building block approach was adopted to characterize the mechanical properties of the joint material, including the fracture toughness between the doubler and facesheet. Twelve four-point-bend samples were tested, six in the sandwich core ribbon orientation and six in sandwich core cross-ribbon direction. Analysis predicted failure initiation and propagation at the pre-delaminated location, consistent with experimental observations. A building block approach using fracture analyses methods predicted failure loads in close agreement with tests. This investigation demonstrated a small strength reduction due to a flaw of significant size compared to the width of the sample. Therefore, concerns of bonding an OOA material to an in-autoclave material was mitigated for the geometries, materials, and load configurations considered.

Damage↗

Failure Predictions of Out-of-Autoclave Sandwich Joints with Delaminations Under Flexure Loads

An analysis and a test program was conducted to investigate the damage tolerance of composite sandwich joints. The joints contained a single circular delamination between the face-sheet and the doubler. The coupons were fabricated through out-of-autoclave (OOA) processes, a technology NASA is investigating for joining large composite sections. The four-point bend flexure test was used to induce compression loading into the side of the joint where the delamination was placed. The compression side was chosen since it tends to be one of the most critical loads in launch vehicles. Autoclave cure was used to manufacture the composite sandwich sections, while the doubler was co-bonded onto the sandwich face-sheet using an OOA process after sandwich panels were cured. A building block approach was adopted to characterize the mechanical properties of the joint material, including the fracture toughness between the doubler and face-sheet. Twelve four-point-bend samples were tested, six in the sandwich core ribbon orientation and six in sandwich core cross-ribbon direction. Analysis predicted failure initiation and propagation at the pre-delaminated location, consistent with experimental observations. Fracture analyses methods predicted failure loads in close agreement with tests. This investigation demonstrated a strength reduction of 10 percent due to a flaw of significant size compared to the width of the sample. Therefore, concerns of bonding an OOA material to an in-autoclave material was mitigated for the geometries, materials, and load configurations considered.

Tolerance↗

Failure Predictions of Out-of-Autoclave Sandwich Joints with Delaminations Under Flexure Loads

An analysis and a test program was conducted to investigate the damage tolerance of composite sandwich joints. The joints contained a single circular delamination between the face-sheet and the doubler. The coupons were fabricated through out-of-autoclave (OOA) processes, a technology NASA is investigating for joining large composite sections. The four-point bend flexure test was used to induce compression loading into the side of the joint where the delamination was placed. The compression side was chosen since it tends to be one of the most critical loads in launch vehicles. Autoclave cure was used to manufacture the composite sandwich sections, while the doubler was co-bonded onto the sandwich face-sheet using an OOA process after sandwich panels were cured. A building block approach was adopted to characterize the mechanical properties of the joint material, including the fracture toughness between the doubler and face-sheet. Twelve four-point-bend samples were tested, six in the sandwich core ribbon orientation and six in sandwich core cross-ribbon direction. Analysis predicted failure initiation and propagation at the pre-delaminated location, consistent with experimental observations. A building block approach using fracture analyses methods predicted failure loads in close agreement with tests. This investigation demonstrated a small strength reduction due to a flaw of significant size compared to the width of the sample. Therefore, concerns of bonding an OOA material to an in-autoclave material was mitigated for the geometries, materials, and load configurations considered.

Tolerance↗

Insulation Reformulation Development

The current Space Launch System (SLS) internal solid rocket motor insulation, polybenzimidazole acrylonitrile butadiene rubber (PBI-NBR), is a new insulation that replaced asbestos-based insulations found in Space Shuttle heritage solid rocket boosters. PBI-NBR has some outstanding characteristics such as an excellent thermal erosion resistance, low thermal conductivity, and low density. PBI-NBR also has some significant challenges associated with its use: Air entrainment/entrapment during manufacture and lay-up/cure and low mechanical properties such as tensile strength, modulus, and fracture toughness. This technology development attempted to overcome these challenges by testing various reformulated versions of booster insulation. The results suggest the SLS program should continue to investigate material alternatives for potential block upgrades or use an entirely new, more advanced booster. The experimental design was composed of a logic path that performs iterative formulation and testing in order to maximize the effort. A lab mixing baseline was developed and documented for the Rubber Laboratory in Bldg. 4602/Room 1178.

Chapman, Cynthia↗

Latex–collagen membrane: an alternative treatment for tibial bone defects

Due to the difficulty of consolidation, the risk of fractures, and the high cost of therapy, the orthopedic field views the restoration of bony defects or post-traumatic diseases as a significant issue. In recent years, efforts have been made toward guided bone regeneration as a viable solution. In this study, natural rubber latex (NRL) and latex–collagen (NRL-COL) membranes were developed and characterized, and their effects on bone regeneration in rat tibial lesions were assessed. According to the physicochemical findings, the hydrolyzed COL was effectively incorporated into the NRL membrane to produce a more robust membrane (348% increase in stress) and showed good biocompatibility for human dermal fibroblast cells and in hemolytic activity assay. According to bone analysis using computed microtomography, a substantial difference in bone volume (BV) was found among NRL, control (CONT), and NRL-COL. NRL-COL exhibited the greatest value for the bone volume/total volume ratio (BV/TV). The presence of NRL and COL was significant for the analysis of BV and BV/TV, respectively. All the experimental groups demonstrated a higher bone quality and fracture resistance, as shown by the mechanical properties of the bone. In the COL group, both neoformation of bone and total collagen levels were greater, indicating that treated defects had been closed and mature bone cells were present. Due to its angiogenic properties and the low cost of NRL membrane production, the NRL-COL membrane could be a good substitute for upcoming bone regeneration applications.

Marcela Britto de Paiva↗

Effect of a ductility layer on the tensile strength of TiAl-based multilayer composite sheets prepared by EB-PVD

TiAl/Nb and TiAl/NiCoCrAl laminate composite sheets with a thickness of 0.4–0.6 mm and dimensions of 150 mm × 100 mm were successfully fabricated by electron beam physical vapor deposition. The microstructures of the sheets were examined, and their mechanical properties were compared with those of TiAl monolithic sheet produced by electron beam physical vapor deposition. Tensile testing was performed at room temperature and 750 °C, and the fracture surfaces were examined by scanning electron microscopy. Among the three microlaminate sheets, the TiAl/NiCoCrAl micro-laminate sheet had the best comprehensive properties at room temperature, and the TiAl/Nb micro-laminate sheet showed the ideal high-temperature strength and plasticity at 750 °C. The result was discussed in terms of metal strengthening mechanism. - Highlights: • TiAl-based multilayer foils was fabricated successfully by using EB-PVD method; • The tensile properties and micro-fracture morphologies of the sheet were investigated; • The deformation behavior of the multilayer foils was discussed.

36 MATERIALS SCIENCE↗

Effect of graphite morphology on the tensile strength and thermal conductivity of cast iron

Highlights: • The graphite morphology is characterized from 3D structure using X–ray tomography. • The size, distribution, shape and interconnectivity of graphite are estimated. • The influences of graphite morphology on tensile properties and thermal conductivity are evaluated. • The mechanism of tensile strength and the model of thermal conductivity are discussed. - Abstract: Graphite morphology is a very important parameter affecting the properties of cast iron. In this study, the graphite morphology was characterized using both 3D and 2D structures. The experimental results revealed that when the graphite was less spheroidal, the graphite had greater interconnectivity in the 3D structure of the cast iron. The size, distribution, volume fraction, and shape of the graphite were estimated. Moreover, the influences of the graphite's morphology, size, and distribution on the tensile property and thermal conductivity at different temperatures were estimated. The experimental results revealed that with an increase in temperature, the thermal conductivity initially increased, and then decreased, whereas the tensile strength decreased slightly at first, and then decreased rapidly. In addition, with an increase in the percentage of compacted graphite, the tensile strength decreased and the thermal conductivity increased. The fracture surfaces of tensile specimens were also estimated. Finally, the mechanism of tensile strength and the model of thermal conductivity were investigated.

36 MATERIALS SCIENCE↗

The effect of space environment exposure on the properties of polymer matrix composite materials (A0180)

The objective of this experiment is to determine the effect of various lengths of exposure to a space environment on the mechanical properties of selected commercial polymer matrix composite materials. Fiber materials will include graphite, boron, S-glass, and PRD-49. The mechanical properties to be investigated are orthotropic elastic constants, strength parameters (satisfying the tensor polynomial relation), coefficients of thermal expansion, impact resistance, crack propagation, and fracture toughness. In addition, the effect of laminate thickness on property changes will also be investigated.

Tennyson, R. C.↗

Tunable thermoplastic elastomer gels derived from controlled-distribution triblock copolymers with crystallizable endblocks

Thermoplastic elastomers (TPEs), a commercially important category of triblock copolymers, are employed alone or upon physical modification with a midblock-selective oil (to form TPE gels, TPEGs) in a broad range of contemporary technologies. While most copolymers in this class of self-networking macromolecules possess glassy polystyrene endblocks and a rubbery polydiene or polyolefin midblock, we investigate TPEGs fabricated from a novel controlled-distribution copolymer with crystallizable polyolefin endblocks and a random-copolymer midblock. According to both electron microscopy and small-angle scattering, the morphologies of these TPEGs remain largely invariant up to 40 wt% oil and then transform considerably at higher oil levels. Although reductions in endblock melting point and crystallinity measured by thermal calorimetry accompany increasing oil content, mechanical properties such as the uniaxial strain at break and fracture toughness improve in some cases by over 50% between 5 and 40 wt% oil. In fact, the strain at break can reach 2500% within this range, thereby confirming that (i) the structure–property relationships of these unique TPEGs are highly composition-tunable and (ii) these TPEGs, stabilized by crystallizable endblocks, provide an attractive alternative for ultrasoft and stretchy recyclable materials.

36 MATERIALS SCIENCE↗

Water diffusion and fracture behavior in nanoporous low-k dielectric film stacks

Among various low-dielectric constant (low-k) materials under development, organosilicate glasses (OSGs) containing nanometer-size pores are leading candidates for use as intrametal dielectrics in future microelectronics technologies. In this paper, we investigate the direct impact of water diffusion on the fracture behavior of film stacks that contain porous OSG coatings. We demonstrate that exposure of the film stacks to water causes significant degradation of the interfacial adhesion energy, but that it has negligible effect on the cohesive fracture energy of the nanoporous OSG layer. Isotope tracer diffusion experiments combined with dynamic secondary ion mass spectroscopy show that water diffuses predominantly along the interfaces, and not through the porous films. This unexpected result is attributed to the hydrophilic character of the interfaces.

36 MATERIALS SCIENCE↗

Influence of injection-induced cooling on deviatoric stress and shear reactivation of preexisting fractures in Enhanced Geothermal Systems

Cold water injection into a hot, fractured, geothermal reservoir may trigger shear activation of pre-existing fractures that can help to enhance reservoir permeability, but may also result in unwanted seismicity. In this study, we investigate through numerical modeling of a hypothetical geothermal reservoir how injection-induced cooling may influence the potential for shear activation, paying special attention to the evolution of deviatoric stress under various stress regimes. In each case, we consider either a reservoir with homogeneous hydraulic properties or the presence of a more permeable fracture zone intersecting the injection well. This fracture zone is either oriented in the maximum (S Hmax ) or minimum (S hmin ) horizontal stress direction. Finally, our main finding is that depending on the configuration, injection-induced cooling stresses can favor or prevent shear reactivation of the preexisting fracture, and this effect can vary temporally and spatially.

58 GEOSCIENCES↗

Multiscale Modeling of Cr 2 O 3 -doped UO 2 Creep and Fracture

The pursuit of UO 2 fuel with various dopants (e.g., Cr 2 O 3 , Al 2 O 3 ) for improved accident tolerance due to larger grain sizes and suspected reductions in fission gas release and creep requires advanced modeling and simulation tools. These tools enable rapid multiscale development and understanding of material behavior in regimes where experimental measurements may be lacking. This work builds upon previous multiscale modeling efforts for fission gas behavior of Cr 2 O 3 -doped UO 2 to begin looking at the effects of dopants on mechanical properties with a particular focus on creep and fracture. The results indicate that dislocation climb is the most dominate creep mechanism at almost all temperatures with sensitivity analyses further providing evidence in support of that claim. Limited experimental data from the Advanced Fuels Campaign (AFC) program in the U. S. Department of Energy on tensile strength of Cr 2 O 3 -doped UO 2 indicates that fracture may be less severe in doped specimens. The results on creep and fracture are preliminary given the large uncertainty associated with the models.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Aging effects on the mechanical properties of alumina-forming austenitic stainless steels

Isothermal aging and tensile evaluation were conducted for recently developed alumina-forming austenitic stainless steels (AFAs). Microstructural observation reveals that NiAl-type B2 and Fe{sub 2}(Mo,Nb)-type Laves phase precipitates form as dominant second phases in the austenitic matrix during aging at 750 C. At room temperature these precipitates increase the strength but decrease the ductility of the AFA alloys. However, when tested at 750 C, the AFA alloys did not show strong precipitation hardening by these phases, moreover, the elongation to fracture was not affected by aging. Fracture surface and cross-sectional microstructure analysis after tensile testing suggests that the difference of mechanical behaviors between room temperature and 750 C results from the ductile-brittle transition of the B2 precipitates. At room temperature, B2 precipitates are strong but brittle, whereas they become weak but ductile above the ductile-brittle transition temperature (DBTT).

36 MATERIALS SCIENCE↗

Surfactants are Ineffective for Reducing Imbibition of Water-Based Fracturing Fluids in Deep Gas Reservoirs

Minimizing loss of injected hydraulic fracturing fluids into shale along fracture-matrix boundaries is desired because imbibed water restricts gas production and wastes valuable water resources. This problem has motivated the addition of surfactants into water-based hydraulic fracturing fluids in order to reduce the capillary driving force for imbibition. Here, we show that reduction in interfacial tension and wettability alteration has negligible ability to reduce imbibition in deep gas reservoirs. The effectiveness of altering capillary forces acting at the wetting front also depends on the injection pressure acting at the fracture-matrix boundary. The pressure at the interface between the fracture and the shale matrix is constrained between the reservoir pore pressure and formation pressure (rock fracture pressure, also known as breakdown pressure of the rock) and increases with depth to magnitudes that greatly exceed that of capillary pressures. Furthermore, the analyses presented here show that even maximum alteration of interfacial properties that result in strongly hydrophobic interactions between the fracturing fluid and reservoir rock is incapable of significantly reducing imbibition in deep reservoirs. Instead of using surfactants, this analysis points to decreases in wellbore shut-in pressures and shut-in times as practical options for reducing imbibition losses of water-based fluids.

03 NATURAL GAS↗

Multiscale Modeling of Cr 2 O 3 -doped UO 2 Creep and Fracture (Rev.1)

The pursuit of UO 2 fuel with various dopants (e.g., Cr 2 O 3 and Al 2 O 3 ) for improved accident tolerance due to larger grain sizes and suspected reductions in fission gas release and creep requires advanced modeling and simulation tools. Such tools enable rapid multiscale development and enhanced understanding of material behavior in regimes for which experimental measurements may be lacking. This work builds on previous multiscale modeling efforts targeting the fission gas behavior of Cr 2 O 3 -doped UO 2 , in order to begin exploring the effects of dopants on mechanical properties, with a particular focus on creep and fracture. The results indicate that dislocation climb is the most dominate creep mechanism at almost all temperatures, and sensitivity analyses provide evidence in further support of this claim. The limited experimental data generated by the U.S. Department of Energy’s Advanced Fuels Campaign (AFC) on the tensile strength of Cr 2 O 3 -doped UO 2 indicate that fracture may be less severe in doped specimens. The results on creep and fracture are preliminary, given the large degree of uncertainty associated with the models.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Mechanical Properties of Nanocrystal Supercrystals

Colloidal nanocrystals attract significant interest due to their potential applications in electronic, magnetic, and optical devices. Nanocrystal supercrystals (NCSCs) are particularly appealing for their well ordered structure and homogeneity. The interactions between organic ligands that passivate the inorganic nanocrystal cores critically influence their self-organization into supercrystals, By investigating the mechanical properties of supercrystals, we can directly characterize the particle-particle interactions in a well-defined geometry, and gain insight into both the self-assembly process and the potential applications of nanocrystal supercrystals. Here we report nanoindentation studies of well ordered lead-sulfide (Pbs) nanocrystal supercrystals. Their modulus and hardness were found to be similar to soft polymers at 1.7 GPa and 70 MPa respectively and the fractures toughness was 39 KPa/m1/2, revealing the extremely brittle nature of these materials.

36 MATERIALS SCIENCE↗

A Critical Review of the Physicochemical Impacts of Water Chemistry on Shale in Hydraulic Fracturing Systems

Hydraulic fracturing of unconventional hydrocarbon resources involves the sequential injection of a high-pressure, particle-laden fluid with varying pH’s to make commercial production viable in low permeability rocks. This process both requires and produces extraordinary volumes of water. The water used for hydraulic fracturing is typically fresh, whereas “flowback” water is typically saline with a variety of additives which complicate safe disposal. As production operations continue to expand, there is an increasing interest in treating and reusing this high-salinity produced water for further fracturing. Here in this paper we review the relevant transport and geochemical properties of shales, and critically analyze the impact of water chemistry (including produced water) on these properties. We discuss five major geochemical mechanisms that are prominently involved in the temporal and spatial evolution of fractures during the stimulation and production phase: shale softening, mineral dissolution, mineral precipitation, fines migration, and wettability alteration. A higher salinity fluid creates both benefits and complications in controlling these mechanisms. For example, higher salinity fluid inhibits clay dispersion, but simultaneously requires more additives to achieve appropriate viscosity for proppant emplacement. In total this review highlights the nuances of enhanced hydrogeochemical shale stimulation in relation to the choice of fracturing fluid chemistry.

54 ENVIRONMENTAL SCIENCES↗

Development and Processing of Nickel Aluminide-Carbide Alloys

With the upper temperature limit of the Ni-based superalloys attained, a new class of materials is required. Intermetallics appear as likely candidates because of their attractive physical properties. With a relatively low density, high thermal conductivity, excellent oxidation resistance, high melting point, and simple crystal structure, nickel aluminide (NiAl) appears to be a potential candidate. However, NiAl is limited in structural applications due to its low room temperature fracture toughness and poor elevated temperature strength. One approach to improving these properties has been through the application of eutectic composites. Researchers have shown that containerless directional solidification of NiAl-based eutectic alloys can provide improvement in both the creep strength and fracture toughness. Although these systems have shown improvements in the mechanical properties, the presence of refractory metals increases the density significantly in some alloys. Lower density systems, such as the carbides, nitrides, and borides, may provide NiAl-based eutectic structure. With little or no information available on these systems, experimental investigation is required. The objective of this research was to locate and develop NiAl-carbide eutectic alloys. Exploratory arc-melts were performed in NiAl-refractory metal-C systems. Refractory metal systems investigated included Co, Cr, Fe, Hf, Mo, Nb, Ta, Ti, W, and Zr. Systems containing carbides with excellent stability (i.e.,HfC, NbC, TaC, TiC, and ZrC) produced large blocky cubic carbides in an NiAl matrix. The carbides appeared to have formed in the liquid state and were randomly distributed throughout the polycrystalline NiAl. The Co, Cr, Fe, Mo, and W systems contained NiAl dendrites with a two-phase interdendritic microconstituent present. Of these systems, the NiAl-Mo-C system had the most promising microstructure for in-situ composites. Three processing techniques were used to evaluate the NiAl-Mo-C system: arc-melting, slow cooling, and containerless directional solidification. Arc-melting provided a wide range of compositions in an economical and simple fashion. The slow cooled ingots provided larger ingots and slower cooling rates than arc-melting. Directional solidification was used to produce in-situ composites consisting of NiAl reinforced with molybdenum carbides.

Newport, Timothy Scott↗