Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FLUORIDE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 991 records · Page 55
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Softening of breathing elastic mode and trigonal elastic mode in the disordered pyrochlore magnet NaCaCo 2 F 7

Cobalt pyrochlore fluoride NaCaCo 2 F 7 is a disordered frustrated magnet that is composed of Co 2+ ions with an effective spin-12 magnetic moment and that exhibits spin freezing below $T_f ~$ 2.4 K. Here, we perform ultrasound velocity measurements on a single crystal of the cubic NaCaCo 2 F 7 . The temperature dependence of the bulk modulus (the breathing elastic mode) exhibits Curie-type softening upon cooling below ~20 K down to $T_f$, which is suppressed by the magnetic field. This Curie-type softening should be a precursor to the enhancement of the strength of exchange disorder via the spin-lattice coupling, which causes the spin freezing. In contrast to the magnetic-field-suppressed Curie-type softening in the bulk modulus, the trigonal shear modulus exhibits softening with a characteristic minimum upon cooling, which is enhanced by the magnetic field at temperatures below ~20 K. This magnetic-field-enhanced elastic anomaly in the trigonal shear modulus suggests a coupling of the lattice to the dynamical spin-cluster state. For NaCaCo 2 F 7 , the observed elastic anomalies reveal an occurrence of magnetic-field-induced crossover from an isostructural lattice instability toward the spin freezing to a trigonal lattice instability arising from the emergent dynamical spin-cluster state.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2021

Sound velocities in shock-compressed soda lime glass: Melting and liquid-state response

Longitudinal sound velocities (and elastic moduli) were determined in soda lime glass (SLG) at peak shock stresses ranging between 40 and 90 GPa. Laser interferometry was used to obtain particle velocity histories and sound velocities by impacting SLG samples on lithium fluoride (LiF) optical windows. In all experiments, the SLG response consists of a sharp jump to a constant state followed by a release wave. The measured longitudinal sound velocities and moduli showed a marked decrease between 52 and 58 GPa, providing experimental evidence for the transformation from an amorphous solid to a liquid in shock-compressed SLG. Furthermore, the stress threshold (~55 GPa) for melting in SLG is considerably lower than the threshold reported in shock-compressed fused silica (~72 GPa), showing the effect of network-modifying cations on the onset of melting. The relative values of sound velocities, shock velocities, and the Hugoniot slopes—between 58 and 90 GPa—are fully consistent with the thermodynamic response of a shock-compressed liquid. Using the experimental results, the Grüneisen parameter (Γ) values were determined for liquid SLG to 90 GPa and then used to provide the Mie-Grüneisen equation of state for liquid SLG.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2025

Mediation of Colloidal Encounter Dynamics by Surface Roughness

Rigorous understanding on the self-assembly of colloidal nanocrystals is crucial to develop tailored nanostructured materials for energy storage, sensing, and optical fields. Despite extensive studies on the self-assembly, a mechanistic understanding of self-assembly under an external field still remains an ongoing challenge. Here, in this work, we used optical tweezers that impose an external attractive force field, resulting in the self-assembly of alpha-phase sodium yttrium fluoride nanocrystals. The dynamic force that is strongly dependent on the surface roughness of the nanocrystals is shown to be a decisive factor for a direct contact between the nanocrystals, manifested by the roughness-dependent hydrodynamic resistivity and Langevin dynamic simulations. Our study provides direct evidence that the role of dynamics is equally important in understanding the self-assembly, which has been rarely observed in the self-assembly in contrast with many studies on the equilibrium forces. These results may have further impact in other fields, such as having explanatory power for the probability of nonclassical crystal growth or the structure of viral spike proteins that affect the probability of viruses binding with cells.

Felsted, Robert G. [Univ. of Washington, Seattle, ↗
DOE OSTI2022

Atomistic modeling of LiF microstructure ionic conductivity and its influence on nucleation and plating

We report the formation and degradation of the solid electrolyte interphase (SEI) and its underlying transport properties play an essential role in the overall performance of lithium-ion batteries. This paper presents classical molecular dynamics studies on polycrystalline inorganic lithium fluoride (LiF) layers to model and predict the SEI transport properties. The ionic conductivity is obtained from the lithium-ion diffusivity in polycrystalline structures of LiF using the Nernst-Einstein relation. The predicted molecular dynamics data are used in a continuum scale phase-field model to evaluate the plating kinetics under fast charging conditions. The analysis emphasizes that the SEI ionic conductivity properties impact the plating dynamics, where SEI's low ion conductivity value is prone to large plating and subsequent capacity degradation. The combination of atomic and continuum scale studies shown herein lays a foundation to tune in SEI transport properties to decrease the amount of lithium plating and improve the performance of fast-charging batteries.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2025

Efficient machine learning interatomic potentials robust for liquid and multiple solid polymorphs of NaF and KF

Achieving atomic-level understanding of crystallization of molten salts is of importance to a wide range of technological applications. Recent work [Fan et al., Proc. Natl. Acad. Sci. USA 122, e2425702122 (2025)] revealed that crystal nucleation in molten LiF salt is a multistage process according to the molecular-dynamics (MD) simulations based on an atomic cluster expansion (ACE) machine-learning interatomic potential (MLIP). In order to understand the influence of increasing cation size on nucleation pathways and nucleation rates of molten fluoride salts, here we develop two new ACE MLIPs for NaF and KF. The two ACE MLIPs feature DFT-SCAN-level accuracy for liquid and multiple solid polymorphs over a wide temperature (0–2000 K) and pressure (0–100 GPa) range, and also reproduce well a number of experimental data for solid and liquid equilibrium properties. The efficiency of the two ACE MLIPs enable million-atom-scale or microsecond-scale MD simulations. The two general-purpose ACE MLIPs are expected to be useful for atomistic simulations for different purposes, in addition to studying crystallization of molten NaF and KF salts.

Crystal melting↗
DOE OSTI2021

Failure Analysis of a New Polyamide-Based Fluoropolymer-Free Backsheet After Combined-Accelerated Stress Testing

The viability of novel coextruded, fluoropolymer-free backsheets for photovoltaic (PV) modules has been questioned as a result of a large number of early-life backsheet failures in PV installations containing one of the earliest co-extruded polyamide (PA)-based backsheet to reach the market, “AAA.” New PV reliability testing protocols have been recently developed and applied to backsheets to reproduce failures observed in the field and evaluate the durability of novel backsheet materials and designs prior to commercialization. A new co-extruded PA-based backsheet was tested using combined-accelerated stress testing (C-AST) and demonstrated a greater lifetime than AAA, and some other fluoropolymer-based backsheets such as polyvinylidene fluoride. The improved PA-based backsheet also eventually failed by through-thickness cracking. Using surface and bulk material characterization techniques, we performed a comprehensive study of material properties before and after the stress testing. Aging of the backsheet resulted in an increase of surface roughness by erosion of the outer PA layer. However the failure is more likely related to an increase in crystallinity of the polyolefin core layer reducing the backsheet tearing energy. The analysis can ultimately inform on the specific weaknesses of the materials so that the manufacturer can improve the backsheet design to extend its lifetime.

14 SOLAR ENERGY↗
DOE OSTI2022

Evaluating Recombination Mechanisms in RbF Treated Cu(In${}_\mathrm{x}$Ga$_\mathrm{1-x}$)Se$_{2}$ Solar Cells

Rubidium fluoride (RbF) postdeposition treatment (PDT) has been shown to improve the performance of Cu(In x Ga 1-x )Se 2 (CIGS) photovoltaic devices. Here, in this study, temperature-dependent current voltage (JVT) and time-resolved photoluminescence (TRPL) experiments were combined with modeling using the solar cell capacitance simulator (SCAPS) computer code to investigate the effect of the RbF PDT. Two devices, one as-deposited and one with RbF PDT, were deposited by a three stage coevaporation process. JVT measurements suggest the dominant recombination mechanism may be tunneling-enhanced recombination via bandtail states, but that defect states in the bandgap can also be important. RbF PDT is shown to decrease the characteristic energy of the bandtails. TRPL data show an increase in the minority carrier lifetime after RbF PDT, leading to an improved open-circuit voltage. SCAPS modeling indicates that the dominant recombination mechanism is dependent on the specific defect makeup of a device, suggesting that small changes in processing conditions can impact device behavior. This explains the observation that, for some devices, defect states in the gap dominate while others, as is the case here, appear to be dominated by bandtails.

14 SOLAR ENERGY↗
DOE OSTI2024

Improved VOC in RbF-Treated Cu(In,Ga)Se2 Solar Cells via Passivation of Recombination Centers

Cu(In,Ga)Se 2 (CIGS) solar cells have benefited in recent years from the addition of heavy alkali elements, such as Rb, which increase the solar cell open-circuit voltage ( V OC ). To investigate the source of this improvement, here, we compare samples with and without Rb to perform a quantitative comparison of electronic defects and minority carrier lifetime. Deep-level transient and optical spectroscopy measurements were performed on two sets of rubidium fluoride (RbF)-treated and untreated CIGS, and three distinct traps were identified regardless of RbF treatment. The RbF treatment was found to reduce the concentration of the H2 trap, which was previously found to act as a recombination center and is located preferentially at CIGS grain boundaries. Time-resolved photoluminescence measurements showed an increase in effective lifetime after RbF and nearly all lifetime improvement resulted from reductions in bulk recombination. The observed V OC improvement is well correlated with increased minority carrier lifetime and acceptor concentration, which led to increases and decreases in electron and hole quasi-Fermi levels, respectively.

Cu(In Ga)Se2 (CIGS)↗
DOE OSTI2023

Mixing in Low Reynolds Number Reacting Impinging Jets in Crossflow

Previous efforts to model uranyl fluoride formation in an impinging jet gas reactor underpredicted spatial mixing and overpredicted chemical conversion into particulates. The previous fluid dynamics model was based on the solution of the Reynolds Averaged Navier Stokes equations. After simulating fluid dynamics, aerosol dynamics were superimposed onto CFD-simulated gas reactant species concentrations. The current work explores the influence of complex unsteady flow features on the overall flow physics and chemistry for a low Reynolds number, opposed flow, impinging jet gas reactor where there is a low Reynolds number cross flow. The objective of this study was to assess the impact of model formulation on scalar mixing and transport. Here, transient flow simulations were performed using Scale Resolving Simulations. Large-Eddy Simulations with the dynamic Smagorinsky turbulence model were performed along with simulations which directly resolved the flow. Average and root-mean-square (RMS) velocities and species concentrations were computed along with modeled and resolved turbulence kinetic energy (TKE), modeled turbulence dissipation, and modeled turbulent viscosity. Lagrangian flow tracers were also used to quantify species concentrations along path lines emanating from the jet tips. Transient simulation data were compared to results from RANS simulations using the k-ω shear stress transport (SST) model and Reynolds Stress Model (RSM). Transient simulations showed spatial mixing patterns which were more consistent with experimental data and helped elucidate the process of particle formation observed in experiments.

42 ENGINEERING↗
DOE OSTI2020

ALLOY SELECTION AND C-276 CODE DESIGN VALUE EXTENSION FOR ADVANCED MOLTEN SALT TECHNOLOGY TEST FACILITIES EXPERIMENTATION

Molten halide salts are being considered as working fluids for nuclear and concentrated solar power applications. High temperature molten fluoride and chloride salts are known to preferentially attack and deplete Cr in alloys, which leads to the use of high-Ni lower-Cr alloys in test facilities for advanced Molten Salt Technology. Alloys 600 and C-276 are two commercially available Ni alloys that have moderate Cr contents and are qualified to the maximum temperature of 649°C and 677°C (1,200°F and 1,251°F), respectively, in the Boiler and Pressure Vessel Code. Both alloys have good corrosion resistance to acids, are resistant to stress-corrosion cracking, and have long track records of use in the chemical industry. Comparatively, Alloy C-276 has a similar Cr content but much higher allowable stresses for temperatures greater than 600°C (1,112°F). Therefore, it has been considered as a structural material for test facilities that require operations at 700°C (1,292°F) or greater to develop high-temperature Molten Salt Technology. To meet the requirements, the current code design values were extended based on some experimental data. Analysis showed that above current Codified maximum temperature, strength of the alloy is mainly controlled by creep rupture life under the average stress, although the Sc creep rate criterion is close to the Favg.Savg rupture criterion. This paper presents the intended test facilities and the design requirements, alloy selection considerations, literature review, data analysis, and proposed allowable stress extension based on some creep test data for C-276 at temperatures greater than 677°C (1,251°F). Further research activities are also briefly mentioned.

Ren, Weiju↗
DOE OSTI2022

Plasma enhanced atomic layer deposition and atomic layer etching of gallium oxide using trimethylgallium

Atomic layer etching driven by self-limiting thermal reactions has recently been developed as a highly conformal and isotropic technique for low damage atomic scale material removal by sequential exposures of vapor phase reactants. Gallium oxide (Ga2O3) is currently among the materials of interest due to a large variety of applications including power electronics, solar cells, gas sensors, and photon detectors. In this study, Ga2O3 was deposited by plasma enhanced atomic layer deposition using trimethylgallium [TMG, Ga(CH3)3] and O2 plasma at a substrate temperature of 200 °C. We report a newly developed method for Ga2O3 thermal atomic layer etching, in which surface modification is achieved through HF exposure resulting in a gallium fluoride surface layer, and then removed through volatile product formation via ligand exchange with TMG. Saturation of the precursor exposure at a substrate temperature of 300 °C resulted in an etch rate of 1.0 ± 0.1 Å/cycle for amorphous Ga2O3. Uniformity and conformality of the atomic layer etching process were confirmed via atomic force microscopy with a measured surface roughness of 0.55 ± 0.05 nm that remains unchanged after etching. The use of TMG for etching may expand available precursors for atomic layer etching processes, while allowing for both etching and deposition of Ga2O3 using the same metalorganic precursor.

Hatch, Kevin A. (ORCID:0000000283118623)↗
DOE OSTI2022

Effects of frequency and pulse width on electron density, hydrogen peroxide generation, and perfluorooctanoic acid mineralization in a nanosecond pulsed discharge gas-liquid plasma reactor

Plasma electron density and temperature were characterized in a continuous flowing gas-liquid film reactor with argon carrier gas by time-resolved optical emission spectroscopy. The plasma parameters were studied as a function of time for varying pulse widths and frequencies. Pulse frequency was varied between 1 and 10 kHz at 16 kV (input voltage) and 40 ns (pulse width) using an Eagle Harbor Technologies, Inc. (EHT) power supply and 5–100 kHz using an Airity Technologies, LLC (AT) power supply. The pulse width was varied between 40 and 200 ns at 16 kV, 2 kHz with the EHT power supply. Optimal frequencies of 5 and 20 kHz were observed for peak electron density with EHT and AT power supplies, respectively. The peak electron density increased with increasing pulse width between 40 and 200 ns using the EHT power supply. Hydrogen peroxide exiting the reactor in the liquid phase increased with discharge power irrespective of the power supply or pulse parameters. Mineralization of 12.5, 50, and 200 ppm perfluorooctanoic acid (PFOA) dissolved in DI water to fluoride (F - ) correlated to the peak electron density. Glycerol, a liquid-phase hydroxyl radical scavenger, depleted hydrogen peroxide but did not affect PFOA mineralization. CO, a gas-phase hydroxyl radical scavenger, led to a reduction in the formation of F - production, suggesting hydroxyl radicals in the gas-liquid film play a necessary, but not singular, role in mineralization of PFOA.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Nucleation and growth of molybdenum disulfide grown by thermal atomic layer deposition on metal oxides

To enable greater control over thermal atomic layer deposition (ALD) of molybdenum disulfide (MoS 2 ), here we report studies of the reactions of molybdenum hexafluoride (MoF 6 ) and hydrogen sulfide (H 2 S) with metal oxide substrates from nucleation to few-layer films. In situ quartz crystal microbalance experiments performed at 150, 200, and 250 °C revealed temperature-dependent nucleation behavior of the MoF 6 precursor, which is attributed to variations in surface hydroxyl concentration with temperature. In situ Fourier transform infrared spectroscopy coupled with ex situ x-ray photoelectron spectroscopy (XPS) indicated the presence of molybdenum oxide and molybdenum oxyfluoride species during nucleation. Density functional theory calculations additionally support the formation of these species as well as predicted metal oxide to fluoride conversion. Residual gas analysis revealed reaction by-products, and the combined experimental and computational results provided insights into proposed nucleation surface reactions. With additional ALD cycles, Fourier transform infrared spectroscopy indicated steady film growth after ~13 cycles at 200 °C. XPS revealed that higher deposition temperatures resulted in a higher fraction of MoS 2 within the films. Deposition temperature was found to play an important role in film morphology with amorphous films obtained at 200 °C and below, while layered films with vertical platelets were observed at 250 °C. Finally, these results provide an improved understanding of MoS 2 nucleation, which can guide surface preparation for the deposition of few-layer films and advance MoS 2 toward integration into device manufacturing.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Challenges in atomic layer etching of gallium nitride using surface oxidation and ligand-exchange

Two atomic layer etching (ALE) methods were studied for crystalline GaN, based on oxidation, fluorination, and ligand exchange. Etching was performed on unintentionally doped GaN grown by hydride vapor phase epitaxy. For the first step, the GaN surfaces were oxidized using either water vapor or remote O 2 -plasma exposure to produce a thin oxide layer. Removal of the surface oxide was addressed using alternating exposures of hydrogen fluoride (HF) and trimethylgallium (TMG) via fluorination and ligand exchange, respectively. Several HF and TMG super cycles were implemented to remove the surface oxide. Each ALE process was monitored in situ using multiwavelength ellipsometry. X-ray photoelectron spectroscopy was employed for the characterization of surface composition and impurity states. Additionally, the thermal and plasma-enhanced ALE methods were performed on patterned wafers and transmission electron microscopy (TEM) was used to measure the surface change. The x-ray photoelectron spectroscopy measurements indicated that F and O impurities remained on etched surfaces for both ALE processes. Ellipsometry indicated a slight reduction in thickness. TEM indicated a removal rate that was less than predicted. In conclusion, we suggest that the etch rates were reduced due to the ordered structure of the oxide formed on crystalline GaN surfaces.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Atomic layer deposition of nanofilms on porous polymer substrates: Strategies for success

Atomic layer deposition (ALD) is a versatile technique for engineering the surfaces of porous polymers, imbuing the flexible, high-surface-area substrates with inorganic and hybrid material properties. Previously reported enhancements include fouling resistance, electrical conductance, thermal stability, photocatalytic activity, hydrophilicity, and oleophilicity. However, there are many poorly understood phenomena that introduce challenges in applying ALD to porous polymers. In this paper, we address five common challenges and ways to overcome them: (1) entrapped precursor, (2) embrittlement, (3) film fracture, (4) deformation, and (5) pore collapse. These challenges are often interrelated and can exacerbate one another. To investigate these phenomena, we applied various ALD chemistries to porous polymers including polyethersulfone, polysulfone, polyvinylidene fluoride, and polycarbonate track-etched membranes. Reaction-diffusion modeling revealed why certain precursors and processing conditions result in embrittling subsurface material growth, entrapment of unreacted precursors, and nongrowth. We quantify the limits of ALD processing temperatures that are dictated by thermal expansion mismatch and can lead to fractured ALD films. The results herein allow us to make recommendations to avoid, mitigate, or overcome the difficulties encountered when performing ALD and plasma-enhanced ALD on porous polymers. We intend this article to serve as a “lessons learned” guide informed by previous experience to provide a better understanding of the difficulties and limitations of ALD on porous polymers and knowledge-based guidelines for successful depositions. This knowledge can accelerate future research and help experimentalists navigate and troubleshoot as they expose porous polymers to reactive precursor vapors.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Monitoring the Reaction Dynamics of UF6 by Cryogenic Layering and FTIR Spectroscopy

Uranium hexafluoride (UF6) is a commonly used material feedstock for uranium enrichment processes. When introduced to water in the atmosphere, it reacts rapidly to form uranyl fluoride (UO2F2). Here, we investigate the UF6 hydrolysis reaction by cryogenically trapping reaction intermediates and characterizing the trapped species by FTIR. The reactant species are sequentially layered onto a diamond substrate held at 10K by a closed cycle liquid helium cryostat. At this temperature, the hydrolysis reaction is not spontaneous and can be catalyzed by the introduction of heat. Upon heating, the reaction moves through several intermediate compounds before proceeding to the final UO2F2 product. Several previously unobserved bands appear while the reaction progresses which may help to elucidate the mechanism behind UF6 hydrolysis.

McNamara, III, Louis E.↗
DOE OSTI2025

Direct measurement of fluorocarbon radicals in the thermal destruction of perfluorohexanoic acid using photoionization mass spectrometry

Thermal destruction is a critical cornerstone of addressing the rampant contamination of natural resources with per- and polyfluoroalkyl substances (PFAS). However, grave concerns associated with stack emissions from incineration exist because mechanistic studies have thus far relied on ex situ analyses of end products and theoretical calculations. Here, we used synchrotron-based vacuum ultraviolet photoionization mass spectrometry to study the pyrolysis of a representative PFAS-perfluorohexanoic acid-and provide direct evidence of fluorocarbon radicals and intermediates. A key reaction pathway from perfluorocarboxylic acids to ketenes via acyl fluorides is proposed. We furthermore propose CF2/CF3 radical-centered pyrolysis mechanisms and explain their roles in the formation of other products that may form in full-scale incinerators. These results have not only unveiled the role of radicals and intermediates in thermal PFAS decomposition and recombination mechanisms but also provide unique insight into improving the safety and viability of industrial PFAS incineration.

Xu, Ming-Gao↗
DOE OSTI2021

Toroidal polar topology in strained ferroelectric polymer

Polar topological texture has become an emerging research field for exotic phenomena and potential applications in reconfigurable electronic devices. Here, we report toroidal topological texture self-organized in a ferroelectric polymer, poly(vinylidene fluoride-ran-trifluoroethylene) [P(VDF-TrFE)], that exhibits concentric topology with anticoupled chiral domains. The interplay among the elastic, electric, and gradient energies results in continuous rotation and toroidal assembly of the polarization perpendicular to polymer chains, whereas relaxor behavior is induced along polymer chains. Such toroidal polar topology gives rise to periodic absorption of polarized far-infrared (FIR) waves, enabling the manipulation of the terahertz wave on a mesoscopic scale. Our observations should inform design principles for flexible ferroic materials toward complex topologies and provide opportunities for multistimuli conversions in flexible electronics.

36 MATERIALS SCIENCE↗