Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FEDS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 991 records · Page 55

Chamber measurements of high CO 2 emissions from a rainforest stream receiving old C-rich regional groundwater

Carbon emissions from fluvial systems are a key component of local and regional carbon cycles. We used floating chambers to investigate the CO 2 flux from stream water to air (f CO 2 ) in the Arboleda, a stream in the lowland rainforest of Costa Rica, fed partly by old regional groundwater high in dissolved inorganic carbon (DIC). Drifting and static chambers showed f CO 2 averaging 35.5 and 72.7 μmol C m –2 s –1 , respectively, bracketing the previously-published f CO 2 value of 56 μmol C m –2 s –1 obtained using tracer methods in this stream. These values are much higher than most f CO 2 data in the literature and reflect a large flux of deep crustal (non-biogenic) CO 2 out of the Arboleda, a flux that does not represent a component of ecosystem respiration. Static chambers appeared to overestimate f CO 2 by creating artificial turbulence, while drifting chambers may have underestimated f CO 2 by under-sampling areas of potentially high gas exchange (e.g., riffles around coarse woody debris obstructions). Both static and drifting chambers revealed high spatial heterogeneity in f CO 2 at the scale of 5–30 m reaches. Some observed temporal trends were localized, e.g., among three reaches with repeated measurements through the wet and dry seasons, (1) only the reach located between the other two showed significantly lower f CO 2 during the dry season, and (2) the highest and lowest f CO 2 were consistently observed in the reaches farthest upstream and downstream, respectively. As a result, streams like the Arboleda receiving significant inputs of high-DIC regional groundwater merit additional study as hotspots for C emissions from terrestrial ecosystems.

54 ENVIRONMENTAL SCIENCES↗

Fischer-Tropsch Synthesis: XANES Investigation of Hydrogen Chloride Poisoned Iron and Cobalt-Based Catalysts at the K-Edges of Cl, Fe, and Co

The effect of co-fed hydrogen chloride (HCl) in syngas on the performance of iron and cobalt-based Fischer-Tropsch (FT) catalysts was investigated in our earlier studies [ACS Catal. 5 (2015) 3124-3136 and DOE final report 2011; Catal. Lett. 144 (2014) 1127-1133]. For an iron catalyst, lower HCl concentrations (< 2.0 ppmw of HCl)) in syngas did not significantly affect the activity, whereas rapid deactivation occurred at higher concentrations (~20 ppmw). With cobalt catalysts, even low concentrations of HCl (100 ppbw) caused catalyst deactivation, and the deactivation rate increased with increasing HCl concentration in the syngas. The deactivation of the catalysts is explained by the chloride being adsorbed on the catalyst surface to (1) block the active sites and/or (2) electronically modify the sites. In this study, XANES spectroscopy was employed to investigate HCl poisoning mechanism on the iron and cobalt catalysts. Cl K-edge normalized XANES results indicate that Cl is indeed present on the catalyst following HCl poisoning and exhibits a structure similar to the family of compounds MCl; two main peaks are formed, with the second peak consisting of a main peak and a higher energy shoulder. At the Co K and Fe K edges, the white line was observed to be slightly increased relative to the same catalyst under clean conditions. There is then the additional possibility that Cl adsorption may act in part to intercept electron density from the FT metallic function (e.g.,cobalt or iron carbide). If so, this would result in less back-donation and therefore hinder the scission of molecules such as CO.

10 SYNTHETIC FUELS↗

Attention-based 3D – convolutional neural network model for mechanical property predictions using visible light images in metal additive manufacturing

Additive manufacturing (AM), while commonly used for rapid prototyping and creating components with complex geometries, has not been widely adopted for critical applications across the aerospace, automotive, defense, energy, and medical industries. This is, in part, due to the challenges of controlling flaws and uncertainty in the mechanical behavior of additively manufactured components. In recent years, there has been an increase in research aimed at predicting the final mechanical properties of additively manufactured components during the printing process. To address these issues, a 3D-CNN model was trained using low-cost in situ visible-light camera data, anomaly classifications, and the chosen process parameters to predict the ultimate tensile strength (UTS), yield strength (YS), total elongation (TE), and uniform elongation (UE). The 3D-CNN layers of the model employed attention mechanisms to prioritize features in the data, thereby improving prediction accuracy. Furthermore, the effect of each process parameter and anomaly class is investigated using attention-based dynamic sigmoid weighted gates to interpret the influence each class has on the final prediction. Different combinations of the in situ data were fed into the 3D-CNN, with varying amounts of image layers, to determine the ideal combination for predicting mechanical properties in situ. Here, the 3D-CNN model achieved mean absolute percentage errors (MAPE) below 5% for both UTS and YS while using only a single camera input and under half of the available image layers.

36 MATERIALS SCIENCE↗

Development of Aluminum LEKIDs for Balloon-Borne Far-IR Spectroscopy

We are developing lumped-element kinetic inductance detectors (LEKIDs) designed to achieve background-limited sensitivity for far-infrared (FIR) spectroscopy on a stratospheric balloon. The spectroscopic terahertz airborne receiver for farinfrared exploration will study the evolution of dusty galaxies with observations of the [CII] 158µm and other atomic fine-structure transitions at z = 0.5–1.5, both through direct observations of individual luminous infrared galaxies, and in blind surveys using the technique of line intensity mapping. The spectrometer will require large format (~1800 detectors) arrays of dual-polarization sensitive detectors with NEPs of 1 × 10 –17 W Hz –1/2 . The low-volume LEKIDs are fabricated with a single layer of aluminum (20-nm-thick) deposited on a crystalline silicon wafer, with resonance frequencies of 100–250MHz. The inductor is a single meander with a linewidth of 0.4µm, patterned in a grid to absorb optical power in both polarizations. As a result, the meander is coupled to a circular waveguide, fed by a conical feedhorn. Initial testing of a small array prototype has demonstrated good yield and a median NEP of 4 × 10 –18 W Hz –1/2 .

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Production of Polyhydroxybutyrate from Ralstonia eutropha H-16 Using Makgeolli Lees Enzymatic Hydrolysate

The objective of this study was to investigate the potential use of waste Makgeolli lees (ML), a by-product of Makgeolli production, as a feedstock for biorefinery production of polyhydroxybutyrate (PHB). ML enzymatic hydrolysate (MLEH) was prepared from ML subjected to liquefaction with amylase and subsequent saccharification with glucoamylase. Since MLEH contains glucose (81 g/L) and protein (39 g/L) among other elements, it was used as the carbon source for PHB production by Ralstonia eutropha H-16. After flask incubation with MLEH, the obtained biomass and PHB content were 10.03 g/L and 34%, respectively, which were higher than the contents obtained when using glucose as the sole carbon source. However, batch fermentation resulted in low PHB accumulation despite suitable cell growth being observed, and these results were thought to be due to the unbalanced C/N ratio. To control the C/N ratio to 20:1, sterile glucose solution was added twice in the fed-batch fermentation with MLEH, and we could obtained dry cell weight and PHB of 36.9 g/L and 24.1 g/L, respectively. Therefore, this study demonstrated the potential use of waste ML as a feedstock for industrial PHB production, which has the important advantage of reduced production cost.

60 APPLIED LIFE SCIENCES↗

Effects of Copolymer Structure on Enzyme-Catalyzed Polyester Recycling

Polyesters are an omnipresent material used for a variety of applications (e.g., bottles, packaging, textile, windshield), roughly comprising 8% of plastics produced worldwide. Enzymatic recycling is an emerging solution to deal with the increasingly diverse polyesters that are not suitable for mechanical recycling. However, enzyme activity and efficiency are still the limiting factors impeding enzymatic recycling for different plastic waste forms. The effects of thermal and structural properties (e.g., glass transition temperature, crystallinity, specific surface area), which are determined by chemical composition and preprocessing, directly influence enzyme recycling efficiency. This work investigates two extrusion methods (single screw and twin-screw extrusion) to pretreat a range of copolyesters (RPET, PETG, Ecozen, Tritan and PBT) and modify their properties (i.e., glass transition temperature (T g ), crystallinity (%), and molecular weight (M n )). A PET-specific enzyme, leaf-branch compost cutinase (LCC ICCG ), produced from a fed-batch fermentation of Escherichia coli BL21(DE3), was used for the enzymatic depolymerization of different polyesters. Several copolyesters showed improved depolymerization after pretreatment, as measured by rate and amount of monomers produced. Furthermore, those that did not depolymerize were found to have exceptionally high glass transition temperature or percent crystallinity, highlighting the importance of these physical parameters on conversion efficiency.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Design of a wideband microstrip nanoantenna array

This paper presents the design of a logarithmic array of microstrip nano-antennas at terahertz frequencies. For applications in which small antennas are required, microstrip antennas are preferred. However, they have a narrow bandwidth. To overcome this problem in microstrip antennas, a log-periodic nanoantenna design is presented which exhibits a wide bandwidth and ultra-compact design. This antenna is smaller in size compared to log-periodic antennas in microwave bands and comparable and better radiation characteristics. The proposed Log-periodic microstrip nanoantenna array consists of seven patch elements on a dielectric layer and are fed directly by a feed line through the branch lines connected to each of the elements. Scaling factor, τ = 0.95 is considered for this design and inset feed is used. In this structure, the substrate has a relative dielectric constant of ε{sub r} = 4.4 and a thickness of h = 800 nm. For good performance at high frequencies, gold is used for the design of the antenna. The considered operating frequency is 3.3 THz corresponding to a wavelength of 91 µm. Good impedance matching and a wide bandwidth of 800 GHz is obtained.

42 ENGINEERING↗

Predicting Thermal Conductivity Evolution of Polycrystalline Materials Under Irradiation Using Multiscale Approach

A multiscale methodology was developed to predict the evolution of thermal conductivity of polycrystalline fuel under irradiation. In the mesoscale level, phase field model was used to predict the evolution of gas bubble microstructure. Generation of gas atoms and vacancies were taken into consideration. In the macroscopic scale, a statistical continuum mechanics model was applied to predict the anisotropic thermal conductivity evolution during irradiation. Microstructure predicted by phase field model was fed into statistical continuum mechanics model to predict properties and behavior. Influence of irradiation intensity, exposition time and morphology were investigated. This approach provides a deep understanding on microstructure evolution and property prediction from a basic scientific viewpoint.

36 MATERIALS SCIENCE↗

Damring Formation During Rotary Kiln Chromite Pre-reduction: Effects of Pulverized Carbonaceous Fuel Selection and Partial Pellet Melting

Electricity consumption is the largest cost contributing factor in the production of ferrochrome. Currently the pelletized chromite pre-reduction process (solid-state reduction of chromite) is the process option with the lowest specific electricity consumption (MWh/ton). In this process, pelletized chromite is fed into a rotary kiln at 1573 K (1300 °C), where partial pre-reduction takes place. Damring formation (material build-up) in the rotary kiln causes routine shutdowns, resulting in loss of revenue. The damring formation is possibly caused by melting of the ash of the pulverized coal used to fire the kiln and/or the partial melting of the chromite pellets. Ash fusion temperatures of twenty different samples were evaluated to assess the temperature at which the pulverized coal ash will start to contribute to damring formation. Sessile drop tests were used to assess the softening behavior of different ore types (e.g., UG2, MG, and LG metgrade), as well as softening of composite chromite pellets made from these ores. Actual damrings were also analyzed using scanning electron microscopy with energy dispersive X-ray spectroscopy. Results indicate that it is mainly the pulverized coal ash that will contribute to damring formation, and not ore or pellet softening. Multiple-linear regression was used to derive equations to predict the ash fusion temperatures of the pulverized coal ash, which can be used by ferrochrome producers to optimize pulverized coal selection.

36 MATERIALS SCIENCE↗

Multiscale Modeling of Microstructural Evolution in Fused-Coating Additive Manufacturing

A quantitative phase field model with adaptive-computational-domain-expansion (ACDE) method was developed to simulate the microstructural evolution in fused-coating additive manufacturing process. A heat transfer and fluid flow model was established to investigate the solidification behavior of the molten pool in a single deposited layer. The solidification parameters such as temperature gradient and solidification rate were calculated from the macroscopic model and then fed into the phase field model to get the microstructure at different positions within a single deposited layer. Columnar dendrites were formed at the bottom of the deposited layer, and equiaxed dendrites appeared in the upper part of the layer. The ACDE method is used to improve the simulation efficiency. The metallographic experiments and energy-dispersive spectrometer analysis for composition were conducted on the fused-coating specimen, and the results were in good accordance with the simulations.

36 MATERIALS SCIENCE↗

Viability of Using Glycerin as a Co-substrate in Anaerobic Digestion of Sugarcane Stillage (Vinasse): Effect of Diversified Operational Strategies

Vinasse, from sugar and ethanol production, stands out as one of the most problematic agroindustry wastes due to its high chemical oxygen demand, large production volume, and recalcitrant compounds. Therefore, the viability of using glycerin as a co-substrate in vinasse anaerobic digestion was tested, to increase process efficiency and biogas productivity. The effect of feeding strategy, influent concentration, cycle length, and temperature were assessed to optimize methane production. Glycerin (1.53% v/v) proved to be a good co-substrate since it increased the overall methane production in co-digestion assays. CH{sub 4} productivity enhanced exponentially as influent concentration increased, but when temperature was increased to 35 °C, biogas production was impaired. The highest methane productivity and yield were achieved using fed-batch mode, at 30 °C and at an organic loading rate of 10.1 kg COD m{sup −3} day{sup −1}: 139.32 mol CH{sub 4} m{sup −3} day{sup −1}, 13.86 mol CH{sub 4} kg COD{sub applied}, and 15.30 mol CH{sub 4} kg COD{sub removed}. Methane was predominantly produced through the hydrogenotrophic route. In order to treat all the vinasse produced by a mid-size sugar and ethanol plant, nine reactors with 7263.4 m{sup 3} each would be needed. The energy generated by burning the biogas in boilers would reach approximately 92,000 MW h per season and could save up to US$ 240,000.00 per month in diesel oil demand.

60 APPLIED LIFE SCIENCES↗

Improvement of Sugarcane Stillage (Vinasse) Anaerobic Digestion with Cheese Whey as its Co-substrate: Achieving High Methane Productivity and Yield

This study investigated methane production in an anaerobic sequencing batch biofilm reactor (AnSBBR) by co-digesting sugarcane vinasse and cheese whey. The assessment was based on the influence of feed strategy, interaction between cycle time and influent concentration, applied volumetric organic load (OLR{sub A}), and temperature over system stability and performance. The system showed flexibility with regard to the feed strategy, but the reduction of cycle time and influent concentration, at the same OLR{sub A}, resulted in lower methane productivity. Increasing organic load, up to the value of 15.27 gCOD L{sup −1} day{sup −1}, favored the process, increasing methane yield and productivity. Temperature reduction from 30 to 25 °C resulted in worse performance, although increasing it to 35 °C provided similar results to 30 °C. The best results were achieved at an OLR{sub A} of 15.27 gCOD L{sup −1} day{sup −1}, cycle time of 8 h, fed-batch operation, and temperature of 30 °C. The system achieved soluble COD removal efficiency of 89%, methane productivity of 208.5 molCH{sub 4} m{sup −3} day{sup −1} and yield of 15.76 mmolCH{sub 4} gCOD{sup −1}. The kinetic model fit indicated methanogenesis preference for the hydrogenotrophic route. At the industrial scale estimative, considering a scenario with a sugarcane ethanol plant with ethanol production of 150,896 m{sup 3} year{sup −1}, it was estimated energy production of 25,544 MWh month{sup −1}.

60 APPLIED LIFE SCIENCES↗

Imaging of atherosclerosis, targeting LFA-1 on inflammatory cells with {sup 111}In-DANBIRT

Background: {sup 111}In-DOTA-butylamino-NorBIRT (DANBIRT) is a novel radioligand which binds to Leukocyte Function-associated Antigen-1 (LFA-1), expressed on inflammatory cells. This study evaluated {sup 111}In-DANBIRT for the visualization of atherosclerotic plaque inflammation in mice. Methods and Results: ApoE{sup −/−} mice, fed an atherogenic diet up to 20 weeks (n = 10), were imaged by SPECT/CT 3 hours post injection of {sup 111}In-DANBIRT (~ 200 pmol, ~ 40 MBq). Focal spots of {sup 111}In-DANBIRT were visible in the aortic arch of all animals, with an average Target-to-Background Ratio (TBR) of 1.7 ± 0.5. In vivo imaging results were validated by ex vivo SPECT/CT imaging, with a TBR up to 11.5 (range 2.6 to 11.5). Plaques, identified by Oil Red O lipid-staining on excised arteries, co-localized with {sup 111}In-DANBIRT uptake as determined by ex vivo autoradiography. Subsequent histological processing and in vitro autoradiography confirmed {sup 111}In-DANBIRT uptake at plaque areas containing CD68 expressing macrophages and LFA-1 expressing inflammatory cells. Ex vivo incubation of a human carotid endarterectomy specimen with {sup 111}In-DANBIRT (~ 950 nmol, ~ 190 MBq) for 2 hours showed heterogeneous plaque uptake on SPECT/CT, after which immunohistochemical analysis demonstrated co-localization of {sup 111}In-DANBIRT uptake and CD68 and LFA-1 expressing cells. Conclusions: Our results indicate the potential of radiolabeled DANBIRT as a relevant imaging radioligand for non-invasive evaluation of atherosclerotic inflammation.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Design and Validation of In-Source Atmospheric Pressure Photoionization Hydrogen/Deuterium Exchange Mass Spectrometry with Continuous Feeding of D{sub 2}O

In this study, continuous in-source hydrogen/deuterium exchange (HDX) atmospheric pressure photoionization (APPI) mass spectrometry (MS) with continuous feeding of D{sub 2}O was developed and validated. D{sub 2}O was continuously fed using a capillary line placed on the center of a metal plate positioned between the UV lamp and nebulizer. The proposed system overcomes the limitations of previously reported APPI HDX-MS approaches where deuterated solvents were premixed with sample solutions before ionization. This is particularly important for APPI because solvent composition can greatly influence ionization efficiency as well as the solubility of analytes. The experimental parameters for APPI HDX-MS with continuous feeding of D{sub 2}O were optimized, and the optimized conditions were applied for the analysis of nitrogen-, oxygen-, and sulfur-containing compounds. The developed method was also applied for the analysis of the polar fraction of a petroleum sample. Thus, the data presented in this study clearly show that the proposed HDX approach can serve as an effective analytical tool for the structural analysis of complex mixtures. .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Conversion of Corn Stover Hydrolysates to Acids: Comparison Between Clostridium carboxidivorans P7 and Microbial Communities Developed from Lake Sediment and an Anaerobic Digester

Anaerobic fermentation is an environmentally sustainable technology for converting a variety of feedstocks to biofuels and bioproducts. Considering the complex nature of lignocellulosic hydrolysates, we aimed to investigate product formation from corn stover hydrolysates by using microbial communities under anaerobic conditions. A community developed from lake sediment was able to produce lactic acid from only glucose in the raw or overlimed hydrolysates. Another community from an anaerobic digester, however, was capable of using all hexose and pentose sugars in the raw and undetoxified hydrolysates and released lactic acid at 26.76 g/L. A pure acetogen, Clostridium carboxidivorans P7, was able to grow on the raw and overlimed hydrolysates, too. But the consumption of sugars was minimal and the total released acid concentrations were less than 2 g/L. Next generation sequencing of the enriched community derived from the anaerobic digester revealed the presence of Lactobacillus strains. The predominant species were Lactobacillus parafarraginis (72.6%) and L. buchneri (13.4%). Product titer from using this enriched community can be further enhanced by cultivating at fed-batch or continuous fermentation modes. Results from this study widened the door for producing valuable products from lignocellulosic feedstocks through using mixed cultures.

09 BIOMASS FUELS↗

Simulation and Emulation of X-Ray Diffraction from Dynamic Compression Experiments

Many important aspects of the dynamic thermo-mechanical response of materials occur at the mesoscale, i.e. a physical scale of interactions smaller than what can be adequately described by homogenous behaviors, yet larger than the scale of the atomic lattice. Concurrent advancements in computational power, continuum theory, and experimental diagnostics are enabling unprecedented understanding of such interactions. However, we cannot develop a sufficient level of confidence in such mesoscale capability until the constitutive description of the underlying constituents is reliably representative of their actual physical behavior. Therefore, there is a strong need to combine experimental, modeling, and data-science techniques to validate models of the thermomechanical response of individual single crystals. One experimental diagnostic with high potential impact to shock physics and materials science is in-situ x-ray diffraction. This paper is primarily focused on simulation of x-ray diffraction in shock physics, but with an aim toward quantifying parametric uncertainty of simulation models. Here, we develop and demonstrate a data-science and model-driven approach to constrain the parameterization of continuum models of crystal lattice deformation associated with the shock response of crystalline materials. The framework is built around the connection between continuum hydrodynamic simulations of lattice deformation and a new Bragg diffraction simulation code, BarberShop. The dynamic deformation of a crystal lattice is modeled using the DiscoFlux model within an arbitrary Lagrangian-Eulerian hydrodynamic code, FLAG. These detailed continuum simulations of lattice deformation can be computationally slow, thus a statistical model is used to emulate the evolution of lattice deformation fields in time and across the considered model parameter space. Emulated lattice deformation fields can then be generated rapidly for any combination of physics model parameters. In turn, these fields can be fed into BarberShop to realize a rapid prediction of Bragg diffraction patterns associated with particular values of physics model parameters. The framework enables parameterization of the single crystal model to obtain Bragg diffraction patterns that most closely resemble a corresponding measurement. Furthermore, the framework naturally provides sensitivities of the lattice deformation to the physics parameters. We highlight the utility of this framework through the application to a synthetic closed-loop inverse problem leading to the parameterization of a single crystal material model. As a model problem, we consider the dynamic response of the energetic molecular crystal, cyclotrimethylenetrinitramine (or RDX), under dynamic compression induced by simulated flyer plate impact experiments.

36 MATERIALS SCIENCE↗

Direct Alcohol Fuel Cells: A Comparative Review of Acidic and Alkaline Systems

In the last 20 years, direct alcohol fuel cells (DAFCs) have been the subject of tremendous research efforts for the potential application as on-demand power sources. Two leading technologies respectively based on proton exchange membranes (PEMs) and anion exchange membranes (AEMs) have emerged: the first one operating in an acidic environment and conducting protons; the second one operating in alkaline electrolytes and conducting hydroxyl ions. In this review, we present an analysis of the state-of-the-art acidic and alkaline DAFCs fed with methanol and ethanol with the purpose to support a comparative analysis of acidic and alkaline systems, which is missing in the current literature. A special focus is placed on the effect of the reaction stoichiometry in acidic and alkaline systems. Particularly, we point out that, in alkaline systems, OH – participates stoichiometrically to reactions, and that alcohol oxidation products are anions. This aspect must be considered when designing the fuel and when making an energy evaluation from a whole system perspective.

25 ENERGY STORAGE↗

Tag you're it: Application of stable isotope labeling and LC-MS to identify the precursors of specialized metabolites in plants

Untargeted liquid chromatography/mass spectrometry (LC-MS) can contribute a comprehensive and unbiased picture of the metabolic space of plants. These data can be used to quantify natural metabolite variation for genome wide association studies, to compare global metabolic responses from environmental or genetic perturbations, and to identify previously undescribed metabolites in Nature. A major limitation with untargeted metabolomics is the classification and identification of the thousands of metabolite features that can be detected in a single analytical run. Isotopic labeling improves the informational value of these datasets by categorizing metabolites as being derived from specific upstream precursors and/or to known metabolic pathways. When a 13 C-labeled precursor is fed to either a plant or tissue, the downstream metabolites produced from it have a higher m/z value than the molecules in the pre-existing pool, generating an m/z peak pair that can be specifically identified within the MS data. In this paper, we outline methods and principles to consider when supplementing untargeted MS data with isotopic labeling, including how to choose the appropriate isotopic label, grow and feed plant tissues to maximize label uptake and incorporation into derivatives, optimize LC-MS methods, and interpret the resulting labeling data. Although the focus here is on annotation of amino acid-derived metabolites using LC-MS, we anticipate that the methods are generally adaptable to other precursors, plant species, and chromatographic approaches.

59 BASIC BIOLOGICAL SCIENCES↗