Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Critical elements”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 991 records · Page 55
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Magneto-optical measurement of magnetic field and electrical current on a short pulse high energy pulsed power accelerator

We describe a direct magneto-optical approach to measuring the magnetic field driven by a narrow pulse width (<10 ns), 20 kA electrical current flow in the transmission line of a high energy pulsed power accelerator. The magnetic field and electrical current are among the most important operating parameters in a pulsed power accelerator and are critical to understanding the properties of the radiation output. However, accurately measuring these fields and electrical currents using conventional pulsed power diagnostics is difficult due to the strength of ionizing radiation and electromagnetic interference. Our approach uses a fiber coupled laser beam with a rare earth element sensing crystal sensor that is highly resistant to electromagnetic interference and does not require external calibration. Here, we focus on device theory, operating parameters, results from an experiment on a high energy pulsed power accelerator, and comparison to a conventional electrical current shunt sensor.

42 ENGINEERING↗
DOE OSTI2024

Design Considerations to Ensure Robustness of the ITER Diagnostics Residual Gas Analyzer

Increasing robustness of the ITER diagnostic residual gas analyzer (DRGA) is critical for the potential control of plasma heating and fuel-cycle processing. Robustness is a requirement for a diagnostic to have a control function. The DRGA is a multisensor diagnostic system capable of resolving isotopic compositions of hydrogen and helium as well as other heavier elements and compounds. The divertor-specific DRGA system is intended to measure the composition of gases in the ITER subdivertor region and midplane. Its analysis station will be located in a port cell at the divertor level. From there, it will sample a slip stream of gas from the cryogenic pump duct. It will then exhaust into a shared roughing line where helium or other light gas impurities, some potentially from other diagnostic systems, are likely to be present. In order to provide reliable measurements, the DRGA must be robust in areas such as plasma optical emission source geometry for a compact design, mitigation of back-streaming from light gases and resilience to the ITER port cell environment, and radiation hardening of the DRGA electronics. By incorporating robustness into the design, areas of plasma heating and fuel-cycle control may be explored with the DRGA for ITER and next-generation fusion devices.

Quinlan, Brendan↗
DOE OSTI2021

Science Capsule: Towards Sharing and Reproducibility of Scientific Workflows

Workflows are increasingly processing large volumes of data from scientific instruments, experiments and sensors. These workflows often consist of complex data processing and analysis steps that might include a diverse ecosystem of tools and also often involve human-in-the-loop steps. Sharing and reproducing these workflows with collaborators and the larger community is critical but hard to do without the entire context of the workflow including user notes and execution environment. In this paper, we describe Science Capsule, which is a framework to capture, share, and reproduce scientific workflows. Science Capsule captures, manages and represents both computational and human elements of a workflow. It automatically captures and processes events associated with the execution and data life cycle of workflows, and lets users add other types and forms of scientific artifacts. Science Capsule also allows users to create `workflow snapshots' that keep track of the different versions of a workflow and their lineage, allowing scientists to incrementally share and extend workflows between users. Our results show that Science Capsule is capable of processing and organizing events in near real-time for high-throughput experimental and data analysis workflows without incurring any significant performance overheads.

Ghoshal, Devarshi↗
DOE OSTI2026

Propulsion System Design using a Dual 3-Phase PM Synchronous Reluctance Machine with X-Type Multi-Level GaN Inverter

— A propulsion system design is exhibited here that comprises of an X-type GaN power module based dual multi-level inverter and a PM Synchronous Reluctance motor. With the critical benefits of multi-level operation, namely low common mode EMI noise, low switching loss, low current Total Harmonic Distortion (THD), smoother torque and lower iron loss, this topology targets high system-level efficiency and high power density while using reduced rare earth (RE) elements in its motor. General Motors and Purdue University jointly designed and developed this 800V class, highly scalable traction drive that can deliver 200+ kW of power suitable for C-SUV to truck vehicle class. The 3-phase electric machine design utilizes dual winding with 6 terminals to work in line with the GaN X-type inverter, and results in a tractive solution that ensures higher machine efficiency while reducing cost and uncertainty related to use and availability of heavy rare earth/rare earth elements in its rotor.

MOMEN, FAIZUL [General Motors LLC, Detroit, MI (Un↗
DOE OSTI2022

Electrochemical Proton Insertion Modulates the Hydrogen Evolution Reaction on Tungsten Oxides

Development of new electrocatalysts for the hydrogen evolution reaction (HER) could reduce dependence on Pt and other rare metals and enable large-scale production of hydrogen with near-zero carbon emissions. Mechanistic insight into the electrocatalytic activity of a material helps to accelerate the development of new electrocatalysts. Alternative electrocatalyst materials such as transition metal oxides and sulfides can undergo insertion reactions that change their properties. Recent reports indicate that the presence of inserted ions can influence electrocatalytic activity. In this work, we utilized a materials chemistry approach to understand the role of proton insertion on the HER activity of layered tungsten oxide hydrates (WO 3 ∙xH 2 O, x = 1, 2). We synthesized a series of tungsten oxide hydrates along with an octylamine-pillared tungsten oxide (OA-WO 3 ). We used cyclic voltammetry to study the electrochemical reactivity of each material and performed ex situ X-ray diffraction and Raman spectroscopy to understand bulk and surface structural changes during electrochemical cycling. We show an inverse relationship between the degree of proton insertion and HER overpotential in tungsten oxides: the lack of proton insertion leads to a high overpotential for the HER. We discuss three hypotheses for how proton insertion leads to HER activity in WO 3 ∙xH 2 O: 1) proton insertion changes the electronic band structure of WO 3 ∙xH 2 O, 2) the presence of bulk protons can influence ΔG H,ads at the surface sites, and 3) inserted protons may participate in the HER mechanism on WO 3 ∙xH 2 O. Overall, this work shows the critical role of proton insertion in enabling high HER activity in tungsten oxides.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Watching Polarons Move in the Energy and Frequency Domains Using Color Impedance Spectroscopy

The hybrid electronic–ionic transport property of π-conjugated polymers enables new (opto)electrochemical device constructs for energy conversion and storage and biosensing applications. One major challenge is separating the energy and frequency dependence of Faradaic events–those involving charge transfer and the redox processes of the conjugated backbone–from the non-Faradaic components, such as ionic motion. Herein, we combine optical spectroscopy with electrochemical impedance spectroscopy (EIS) to resolve the frequency response of ionic–electronic coupling as a function of electrochemical doping potential. First, using EIS, we identify two different frequency regimes resulting in potential-dependent capacitive elements on the order of ~10 μF/cm 2 in a high-frequency regime and ~50–150 μF/cm 2 in a low-frequency regime. Given the larger magnitude and greater potential dependence, we posit that polaronic motion is more likely to occur at low frequencies (<1 kHz) and overlaps with ionic motion. The use of color impedance spectroscopy (CIS) enables observation of polaronic motion with frequency modulation. We observe that higher doping potentials show a greater motion of polarons above the DC-bias baseline concentration for onset in electrochemical doping, but all potentials considered demonstrate a critical frequency at which the polaronic motion is “frozen” (~40 Hz). Furthermore, this critical information obtained from CIS in highly dielectric environments offers a unique figure of merit for future studies on electronic–ionic coupling by which to compare across polymer/electrolyte interfaces, including the role of a charge-supporting electrolyte, a solvent, and alternative Faradaic processes (e.g., electrocatalysis).

36 MATERIALS SCIENCE↗
DOE OSTI2022

Atomistic modeling of tensile deformation and fracture of carbon fibers: Nanoscale stress redistribution, effect of local structural characteristics and nanovoids

The mechanisms of tensile deformation and fracture of carbon fibers are investigated in large-scale molecular dynamics simulations. The simulations performed for computational samples with different structural characteristics enable analysis of the structural sensitivity of the mechanical properties. It is found that the carbon fiber nanostructure can be represented by a fine (nanoscale) mixture of stiff and soft regions. Despite the nanoscale structural heterogeneity of the computational fibers, their fracture strain and tensile strength exceed the experimental values by almost an order of magnitude. Here, this observation is explained by the ability of the carbon fiber nanostructure, largely consisting of curved and folded layers of turbostratic carbon, to exhibit continuous nanoscale load redistribution during the deformation. The transient, fluid nature of a percolating cluster of stress-holding structural elements prevents stress localization at the early stage of the deformation and enables the fiber nanostructure to adapt to the increasing load. Overall, the results of the simulations suggest that the design of advanced carbon fiber manufacturing and post-processing methods focused on the elimination of critical mesoscopic structural defects (internal voids, foreign inclusions, and surface flaws) can yield a substantial increase in the strength and fracture strain of carbon fibers.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Stability Criteria for Self-Propagating Reaction Waves in Co/Al Multilayers

The propagation of self-sustained formation reactions in sputter-deposited Co/Al multilayers is known to exhibit a design-dependent instability. Multilayers having thin bilayers (<55 nm period) exhibit stable propagating waves, whereas those with a larger period react unstably. The specific two-dimensional (2D) instability observed involves the transverse propagation of a band in front of a stalled front commonly referred to as a “spin band.” Previous finite-element studies have shown that these instabilities are thermodynamically driven by the forward conduction of heat away from the flame front. However, the magnitude of that loss is inherently tied to the bilayer design in traditional bimetallic multilayers, which couples any proposed stability criteria to a varying critical diffusion distance. Here, this work utilizes a recently developed class of materials known as “inert-mediated reactive multilayers” to decouple the thermodynamic and kinetic contributions to propagating wave stability by reducing the stored chemical energy density in normally stable bilayer designs. By depositing an inert product phase (B2-CoAl) within the mid-plane of Co and Al reactant layers, spin instabilities arise as a function of both diluted volume and critical diffusion distance. From there, a stability criterion is determined for Co/Al multilayers based on enthalpy loss from the reaction zone, and its physical significance is explored.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Characterizing Human Performance: Detecting Targets at High False Alarm Rates [Slides]

Analysts develop a “no threat” bias with high false alarms. If only shown alarms for actual attacks, may never actually see an alarm. We see this in the laboratory, but not often studied in applied environments. (TSA is an exception.) In this work, near-operational paradigms are useful, but difficult to construct well. Pilot testing is critical before engaging time-limited professionals. Experimental control is difficult to balance with operational realism. Grounding near-operational experiments in basic research paradigms has both advantages and disadvantages. Despite shortcomings in our second experiment, we now have a platform for experimental investigations into the human element of physical security systems.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗
DOE OSTI2021

National Emission Standards for Hazardous Air Pollutants – Radionuclide Emissions Calendar Year 2020

The U.S. Department of Energy (DOE), National Nuclear Security Administration Nevada Field Office (NNSA/NFO) operates the Nevada National Security Site (NNSS) and the North Las Vegas Facility (NLVF). From 1951 through 1992, the NNSS was the continental testing location for U.S. nuclear weapons. Radionuclides in air from NNSS activities have been monitored since the initiation of atmospheric testing. After 1962, testing was limited to underground detonations, which greatly reduced radiation exposure to the public. Since the end of nuclear testing in 1992, radiation monitoring has focused on detecting airborne radionuclides from historically contaminated soils because this sources dominates the potential offsite dose. These radionuclides are derived from re-suspension of soil (primarily by wind) and emission of tritium-contaminated soil moisture through evapotranspiration. Low amounts of legacy-related tritium are also emitted to air at the NLVF, an NNSS support complex in North Las Vegas. To protect the public from harmful levels of manmade radiation, the Clean Air Act, National Emission Standards for Hazardous Air Pollutants (NESHAP), specifically the National Emission Standards for Emissions of Radionuclides Other Than Radon From Department of Energy Facilities (40 CFR 61, Subpart H, 2020) limits the release of radioactivity from a DOE facility to that which would cause 10 millirem per year (mrem/y) effective dose equivalent (EDE) to any member of the public. This limit does not include radiation unrelated to NNSS activities. Unrelated doses could come from naturally occurring radioactive elements, from sources such as medically or commercially used radionuclides, or from sources outside of the United States, such as Japan’s Fukushima nuclear power plant, which was damaged in 2011. NNSA/NFO demonstrates compliance with the NESHAP limit by reporting environmental measurements of radionuclide air concentrations at critical receptor locations on the NNSS. This alternative was proposed and formerly submitted to the U.S. Environmental Protection Agency (EPA) in 2001 (EPA 2001a) and has been the method used to demonstrate compliance with the 40 CFR 61.92 dose standard since 2005. Six locations on the NNSS have been established to act as critical receptor locations to demonstrate compliance with the NESHAP limit. These locations are closer to radionuclide releases than where the public resides so they act as protective substitutes for public receptor locations. Compliance is demonstrated if the measured annual average concentration is less than the NESHAP Concentration Level (CL) for Environmental Compliance listed in Table 2 of 40 CFR 61, Appendix E. For multiple radionuclides, compliance is demonstrated when the sum of the fractions (determined by dividing each radionuclide’s concentration by its CL and then adding the fractions together) is less than 1.0. The EPAapproved air transport model, called the Clean Air Package 1988 (CAP88-PC) is also used to calculate the effective dose equivalent to the maximally exposed individual from NNSS air emissions. CAP88-PC was also used to calculate the population dose, or the collective EDE (expressed as person-rem [roentgen equivalent man] per year [person-rem/y]) for all individuals combined who reside within 80 kilometers (km) of NNSS emission sources. In 2020, the potential dose from radiological emissions to air from both current and past NNSS activities was well below the 10 mrem/y dose limit. This is demonstrated by both the air sampling data collected at critical receptor air monitoring stations and CAP88-PC modeling. The average concentrations of radioactivity at air critical receptor stations ranged from 0.2% to a maximum of 4.2% of the allowed NESHAP limit. CAP88-PC modeling of all 2020 NNSS radionuclide emissions showed the maximally exposed individual to be in Amargosa Valley and this individual received a potential dose of 0.063 mrem/y. The collective dose was calculated to be 0.29 person-rem/year for the 521,300 people who lived within 80 km of NNSS emission sources.

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2025

JENSA: Past, present, and future

Nuclear reaction studies rely on three main physical components: the beam of nuclei provided by the facility, the detector systems used to measure the outgoing particles of interest, and the target. Target fabrication is thus a critical aspect of studying the reactions that power stars and probe the evolution of nuclear structure. The Jet Experiments in Nuclear Structure and Astrophysics (JENSA) gas jet target is the most dense helium jet target for rare isotope beam reaction studies in the world, providing targets of gaseous elements such as helium, nitrogen, and neon. A brief overview of the design and operation of JENSA, including commissioning and recent science experiments, and a discussion the future of JENSA coupled to the dedicated recoil separator SECAR, are presented.

Chipps, Kelly [ORNL] (ORCID:0000000330501298)↗
DOE OSTI2024

Insights into water extraction and aggregation mechanisms of malonamide-alkane mixtures

Structure at the nanoscale in the organic phase of liquid–liquid extraction systems is often tied to separation performance. However, the weak interactions that drive extractant assembly lead to poorly defined structures that are challenging to identify. Here, in this work, we investigate the mechanism of water extraction for a malonamide extractant commonly applied to f-element separations. We measure extractant concentration fluctuations in the organic phase with small angle X-ray scattering (SAXS) before and after contact with water at fine increments of extractant concentration, finding no qualitative changes upon water uptake that might suggest significant nanoscopic reorganization of the solution. The critical composition for maximum fluctuation intensity is consistent with small water–extractant adducts. The extractant concentration dependence of water extraction is consistent with a power law close to unity in the low concentration regime, suggesting the formation of 1 : 1 water–extractant adducts as the primary extraction mechanism at low concentration. At higher extractant concentrations, the power law slope increases slightly, which we find is consistent with activity effects modeled using Flory–Huggins theory without introduction of additional extractant–water species. Molecular dynamics simulations are consistent with these findings. The decrease in interfacial tension with increasing extractant concentration shows a narrow plateau region, but it is not correlated with any change in fluctuation or water extraction trends, further suggesting no supramolecular organization such as reverse micellization. This study suggests that water extraction in this system is particularly simple: it relies on a single mechanism at all extractant concentrations, and only slightly enhances the concentration fluctuations characteristic of the dry binary extractant/diluent mixture.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

43-0434 Bridge Inspection Report 2021

The documentation includes the following: 1. 2021 NMDOT Bridge Inspection Report including Element Level Data Collection (in digital formats prepared by NMSU)--conforms to the National Bridge Inspection Standards and AASHTO Manual for Bridge Element Inspection; 2. 2021 Supplemental Report (in digital formats prepared by NMSU)--provides detailed information related to current condition of major bridge components; 3. 2021 Inspection Pictures (in digital format prepared by NMSU); 4. 2021 Delamination Map (in digital format prepared by LANL). During the 2021 inspection, three critical findings were reported to our LANL contact, Mr. Jonathan Stein, by text and/or email on June 26, 2021. 1. The south joint of the bridge had a modular section of the joint that could potentially come loose during the passing of vehicles. This was reported as a critical finding for safety. If the modular section becomes dislodged or deformed it could pose a serious hazard that could result in a punctured tire to vehicles, motorcyclists and/or bicyclist causing drivers/riders to lose control; 2. The bracket plate located at the north end of the bridge on the pedestrian walkway was corroded through and provides little protection to pedestrians and bicyclists. This was reported as a critical finding for safety to prevent injuries to people; 3. The north approach rail has three missing posts. These posts help ensure that traffic is redirected and the energy is absorbed by the rail. This was reported as a critical finding for safety. Additionally, the approach rail is on a curve with a nearby drop off. Immediate repair is recommended. Based on the 2021 inspection, the bridge deck is rated in "fair" condition. The chain drag performed on the deck identified several areas with delamination that are concentrated near the expansion joints, in the closure joint of the deck near the bridge centerline, and at the south end of the northbound lanes. The chain drag performed during the 2021 inspection revealed 215,333 sq. in. (1495 sq. ft) of delaminations and patched areas (not including the sidewalk). This is approximately a 600% increase from 2019. It is recommended that the delaminations and spalls with exposed rebar be repaired. The "delaminated area" map for the 2021 inspection is provided in the supplemental report.

42 ENGINEERING↗
DOE OSTI2021

Stable, high-performance, dendrite-free, seawater-based aqueous batteries

Metal anode instability, including dendrite growth, metal corrosion, and hetero-ions interference, occurring at the electrolyte/electrode interface of aqueous batteries, are among the most critical issues hindering their widespread use in energy storage. Herein, a universal strategy is proposed to overcome the anode instability issues by rationally designing alloyed materials, using Zn-M alloys as model systems (M = Mn and other transition metals). An in-situ optical visualization coupled with finite element analysis is utilized to mimic actual electrochemical environments analogous to the actual aqueous batteries and analyze the complex electrochemical behaviors. The Zn-Mn alloy anodes achieved stability over thousands of cycles even under harsh electrochemical conditions, including testing in seawater-based aqueous electrolytes and using a high current density of 80 mA cm –2 . The proposed design strategy and the in-situ visualization protocol for the observation of dendrite growth set up a new milestone in developing durable electrodes for aqueous batteries and beyond.

25 ENERGY STORAGE↗
DOE OSTI2023

Emergent superconductivity in topological-kagome-magnet/metal heterostructures

Itinerant kagome lattice magnets exhibit many novel correlated and topological quantum electronic states with broken time-reversal symmetry. Superconductivity, however, has not been observed in this class of materials, presenting a roadblock in a promising path toward topological superconductivity. Here, we report that novel superconductivity can emerge at the interface of kagome Chern magnet TbMn 6 Sn 6 and metal heterostructures when elemental metallic thin films are deposited on either the top (001) surface or the side surfaces. Superconductivity is also successfully induced and systematically studied by using various types of metallic tips on different TbMn 6 Sn 6 surfaces in point-contact measurements. The anisotropy of the superconducting upper critical field suggests that the emergent superconductivity is quasi-two-dimensional. Remarkably, the interface superconductor couples to the magnetic order of the kagome metal and exhibits a hysteretic magnetoresistance in the superconducting states. Taking into account the spin-orbit coupling, the observed interface superconductivity can be a surprising and more realistic realization of the p-wave topological superconductors theoretically proposed for two-dimensional semiconductors proximity-coupled to s-wave superconductors and insulating ferromagnets. Our findings of robust superconductivity in topological-Chern-magnet/metal heterostructures offer a new direction for investigating spin-triplet pairing and topological superconductivity.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2021

Topology-dependent stability of vortex-antivortex structures

The non-trivial topology of magnetic structures such as vortices and skyrmions is considered as a key concept to explain the stability of those structures. The stability, dictated by non-trivial topology, provides great potential for device applications. Although it is a very critical scientific and technological issue, it is elusive to experimentally study the topology-dependent stability owing to the difficulties in establishing stably formed magnetic structures with different topologies. Here, we establish a platform for vortex-antivortex structures with different topological charges within Ni 80 Fe 20 rectangular elements thick enough to stabilize a unique three-dimensional magnetic structure with non-uniform magnetization along the thickness of the elements. The detailed magnetization configurations of the three-dimensional vortex-antivortex structures and their annihilations during their field-driven motions are investigated by utilizing magnetic transmission soft x-ray microscopy and micromagnetic simulation. We demonstrate that the stability of vortex-antivortex structures significantly depends on their topologies and the topology-dependent stability is associated with their different annihilation mechanisms. Furthermore, we believe that this work provides in-depth insight into the stability of magnetic structures and its topology dependence.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Functionally graded magnetic materials: a perspective to advance charged particle optics through compositional engineering

Additive manufacturing has ushered in a new paradigm of bottom-up materials-by-design of spatially non-uniform materials. Functionally graded materials have locally tailored compositions to provide optimized global properties and performance. In this letter, we propose an opportunity for the application of graded magnetic materials as lens elements for charged particle optics. A Hiperco50/Hymu80 (FeCo-2 V/Fe-80Ni-5Mo) graded magnetic alloy was successfully additively manufactured via Laser Directed Energy Deposition with spatially varying magnetic properties. The compositional gradient is then applied using computational simulations to demonstrate how a tailored material can enhance the magnetic performance of a critical, image-forming component of a transmission electron microscope.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Micromechanical Surrogate Machine Learning Model for Creep Deformation Modeling

Process variability during the manufacture of gas turbine engine hot section components can significantly affect the material’s resulting microstructure. In casting, for instance, geometric variation within a component (thin sections versus thick sections, radial location) influences cooling rates and the resulting grain size. The high temperature creep response is known to be sensitive to grain size owing to a diffusional creep mechanism which occurs more readily along grain boundaries. Microstructural variation correspondingly drives mechanical behavior which propagates into component scale performance uncertainty. These factors are essential when planning inspection, maintenance, and repair strategies within a reliability framework. These benefits provide opportunities to increase overall energy efficiency through refined margins. Critically, there is an opportunity to bolster existing data-driven reliability models using physics-driven process-structure-property relations. Here we present recent work establishing a framework for evaluating the probabilistic creep performance of high-temperature materials. A novel microstructure-sensitive crystal plasticity finite element model is established that captures both grain boundary and crystallographic deformation effects. The computationally expensive physics model is calibrated using a statistical approach and this high-fidelity model is subsequently used to train a computationally efficient machine learning surrogate model. The surrogate model is essential for sampling a large ensemble of simulated structure-property pair results. The ensemble data are then mined to extract salient trends to be incorporated into a microstructure-sensitive reliability model. The proposed approach represents a novel way to capture microstructure-sensitive trends from physics-based models within a modern reliability framework.

Fernandez-Zelaia, Patxi [ORNL]↗