Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Compressor”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 991 records · Page 55

Laser anemometer measurements in a transonic axial flow compressor rotor

A laser anomometer system employing an efficient data acquisition technique has been used to make measurements upstream, within, and downstream of the compressor rotor. A fluorescent dye technique allowed measurements within endwall boundary layers. Adjustable laser beam orientation minimized shadowed regions and enabled radial velocity measurements outside of the blade row. The flow phenomena investigated include flow variations from passage to passage, the rotor shock system, three-dimensional flows in the blade wake, and the development of the outer endwall boundary layer. Laser anemometer measurements are compared to a numerical solution of the streamfunction equations and to measurements made with conventional instrumentation.

Strazisar, A. J.↗

Comparison between optical measurements and a numerical solution of the flow field within a transonic axial-flow compressor rotor

A comparison between numerical and experimental results is presented for the flowfield within a transonic axial-flow compressor rotor. The rotor was tested at design speed and a wide open throttle discharge condition. The relative tip Mach number was 1.4. A laser anemometer system was used to measure velocity and flow angle upstream, within, and downstream of the rotor. A holographic interferometer was used to visualize the rotor shock system near the tip. The computational procedure solves the full three-dimensional Euler equations using a time-marching technique. Shock location and shape determined from the two optical systems are compared. Calculated relative Mach number and flow angle contours, shock locations, and shock strength are compared to values measured with the laser anemometer.

Strazisar, A. J.↗

Experimental study of low aspect ratio compressor blading

The paper presents a study of low aspect blading for the inlet stages of a high pressure ratio, high-speed core compressor. The basic overall design variables were stage pressure ratio and blade aspect ratio; these four stages represent two levels of total pressure ratio, two levels of rotor blade aspect ratio, and two levels of stator vane aspect ratios. Comparisons of the overall performance, radial distributions of performance parameters, diffusion factors at the near-stall conditions, blade element data, and the axial distribution of rotor tip static pressures yielded the following results: (1) higher peak pressure ratio, high stage and rotor efficiencies, and greater stall margin were obtained with the lower aspect ratio blading, (2) the lower aspect ratio blading showed improved performance over the entire blade span, and (3) the lower aspect ratio rotors operated at higher diffusion factors and higher incidence angles over the entire blade span.

Reid, L.↗

Core compressor exit stage study. Volume 3: Data and performance report for screening test configurations

Rear stage blading designs that have lower losses in their endwall boundary layer regions were developed. Test data and performance results for rotor B, stator B, and stator C - blading designs that offer promise of reducing endwall losses relative to the baseline are given. A low speed research compressor was the principal investigative tool. The tests were conducted using four identical stages of blading so that the test data would be obtained in a true multistage environment.

Wisler, D. C.↗

Core compressor exit stage study. Volume 2: Data and performance report for the baseline configuration

The objective of the program is to develop rear stage blading designs that have lower losses in their endwall boundary layer regions. The overall technical approach in this efficiency improvement program utilized General Electric's Low Speed Research Compressor as the principal investigative tool. Tests were conducted in two ways: using four identical stages of blading so that test data would be obtained in a true multistage environment and using a single stage of blading so that comparison with the multistage test results could be made.

Wisler, D. C.↗

Program to develop sprayed, plastically deformable compressor shroud seal materials

A study of fundamental rub behavior for 10 dense, sprayed materials and eight current compressor clearance materials was conducted. A literature survey of a wide variety of metallurgical and thermophysical properties was conducted and correlated to rub behavior. Based on the results, the most promising dense rub material was Cu-9A1. Additional studies on the effects of porosity, incursion rate, blade solidity, and ambient temperature were carried out on aluminum bronze (Cu-9Al-1Fe) with and without a 515B Feltmetal underlayer. A further development effort was conducted to assess the property requirements of a porous, aluminum bronze, seal material. Strength, thermal cycle capabilities, erosion and oxidation resistance, machinability, and abradability at several porosity levels were examined.

Schell, J. D.↗

The boundary layer on compressor cascade blades

The flow field about an airfoil in cascade at a Reynolds number of 5 x 10 to the 5th power is described. Hot wire and laser anemometry are combined with flow visualization techniques in order to obtain detailed flow data (e.g., boundary layer profiles, points of separation, and the transition zone) on a cascade of relatively highly loaded blades. Benchmark data is provided for the evaluation of current and future predictive models, in this way aiding in the compressor design process.

Deutsch, S.↗

Semi-actuator disk theory for compressor choke flutter

A mathematical anaysis predict the unsteady aerodynamic utilizing semi actuator theory environment for a cascade of airfoils harmonically oscillating in choked flow was developed. A normal shock is located in the blade passage, its position depending on the time dependent geometry, and pressure perturbations of the system. In addition to shock dynamics, the model includes the effect of compressibility, interblade phase lag, and an unsteady flow field upstream and downstream of the cascade. Calculated unsteady aerodynamics were compared with isolated airfoil wind tunnel data, and choke flutter onset boundaries were compared with data from testing of an F100 high pressure compressor stage.

Micklow, J.↗

Abradable compressor and turbine seals, volume 2

The applications and advantages of abradable coatings as gas path seals in a general aviation turbofan engine were investigated. Abradable materials were evaluated for the high pressure radial compressor and the axial high and low pressure turbine shrouds.

Sundberg, D. V.↗

Cold-air performance of compressor-drive turbine of Department of Energy upgraded automobile gas turbine engine. 1: Volute-manifold and stator performance

The aerodynamic performance of the inlet manifold and stator assembly of the compressor drive turbine was experimentally determined with cold air as the working fluid. The investigation included measurements of mass flow and stator-exit fluid torque as well as radial surveys of total pressure and flow angle at the stator inlet and annulus surveys of total pressure and flow angle at the stator exit. The stator-exit aftermixed flow conditions and overall stator efficiency were obtained and compared with their design values and the experimental results from three other stators. In addition, an analysis was made to determine the constituent aerodynamic losses that made up the stator kinetic energy loss.

Roelke, R. J.↗

End wall flows in rotors and stators of a single stage compressor

A solution of the flow in the rotor end wall region, including the effects of tip clearance flow, is presented. A method for leakage flow measurement at the tip of a compressor rotor blade is discussed. Measurements are given for a rotor hub wall boundary layer.

Govindam, T. R.↗

Structure and decay characteristics of turbulence in the near- and far-wake of a moderately loaded compressor rotor-blade

The wake of a turbomachinery rotor-blade is turbulent, highly three-dimensional, and nonisotropic with appreciable curvature in the trailing-edge and near-wake regions. The characteristics of the turbulence vary considerably with radius, blade loading, free-stream turbulence, Reynolds number, and the rotor-blade geometry. This paper is concerned with the turbulence properties of a moderately loaded compressor blade, particularly near the blade trailing-edge. The tangential variation of the axial, tangential and radial intensities and stresses across the wake, as well as their decay characteristics were measured with a tri-axial hot-wire probe in the rotor frame of reference. The decay of intensities and stresses were found to be very rapid in the trailing-edge and near-wake regions and slow in the far-wake region. The effects of inlet-guide-vane and the hub-wall boundary layers on the rotor wake turbulence spectra are also discussed. Similarity rules for the three components of intensity are also derived and presented in this paper.

Ravindranath, A.↗

Effects of solid particles suspended in fluid flow through an axial flow compressor stage

An approximate method for calculating the flow properties of gas-particle mixture flowing over blades in a cascade is studied. Using an analytical method, the solid particle trajectory and location of collisions between the solid particles and the blade surfaces are determined. In addition an experimental investigation of the trajectories and velocities of solid particles suspended in a fluid passing through an axial flow compressor cascade was performed. The cascade blades were made of 2024 aluminum alloy and the solid particles used were quartz sand with average diameter of 165 microns. The following parameters were investigated: blade pressure distribution, and total pressure loss coefficient, both depending on the degree of erosion. In addition, a theoretical estimation of the blade erosion is compared with the experimental data.

Tabakoff, W.↗

Rotor wake mixing effects downstream of a compressor rotor

An experimental study of rotor wake was conducted in the trailing-edge and near-wake regions of a moderately loaded compressor rotor blade using a rotating triaxial hot-wire probe in a rotating frame of reference. The flow-field was surveyed very close to the trailing-edge as well as inside the annulus- and hub-wall boundary layers. The large amount of data acquired during this program has been analyzed to discern the decay effects as well as the spanwise variation of three components of velocity, three components of intensities and three components of shear stresses. The data set also include extensive information on the variation of the flow properties downstream. The other derived quantities include wake momentum thickness and deviation angles at various spanwise and downstream locations. These data are presented and interpreted, with emphasis on the downstream mixing as well as endwall-wake interaction effects.

Ravindranath, A.↗

Turbulence characteristics in the annulus-wall boundary layer and wake mixing region of a compressor rotor exit

The flow at the exit of a turbomachinery rotor near the annulus wall is three-dimensional with a varying degree of turbulence and nonisotropic characteristics. The characteristics of the turbulence vary considerably with radial and axial location, blade loading, Reynolds number, free-stream turbulence, and the rotor blade geometry. This paper is concerned with the turbulence properties near the annulus wall region of a moderately loaded compressor blade. The variation of the streamwise, normal, and radial intensities as well as the stresses across the wake, its profile and decay characteristics, were determined with a tri-axial hot-wire probe in the stationary frame of reference. The turbulence characteristics in the annulus-wall region of the rotor exit were found to be highly complex due to the interaction of the blade wake and the annulus wall.

Davino, R.↗

Core compressor exit stage study. Volume 5: Design and performance report for the Rotor C/Stator B configuration

Rear stage blading designs that have lower losses in their endwall boundary layer regions were developed. The design of rotor-C and the performance results for rotor-C running with stator B are described. A low speed research compressor is utilized as the principal investigative tool. Four identical stages of blading are used to obtained data in a true multistage environment.

Wisler, D. C.↗

The use of optimization techniques to design controlled diffusion compressor blading

A method for automating compressor blade design using numerical optimization, and applied to the design of a controlled diffusion stator blade row is presented. A general purpose optimization procedure is employed, based on conjugate directions for locally unconstrained problems and on feasible directions for locally constrained problems. Coupled to the optimizer is an analysis package consisting of three analysis programs which calculate blade geometry, inviscid flow, and blade surface boundary layers. The optimizing concepts and selection of design objective and constraints are described. The procedure for automating the design of a two dimensional blade section is discussed, and design results are presented.

Sanger, N. L.↗

Comparison of two and three dimensional flow computations with laser anemometer measurements in a transonic compressor rotor

A procedure for using an efficient axisymmetric code to generate downstream pressure input for more costly Euler codes is discussed. Two and three dimensional inviscid solutions for the flow within a transonic axial compressor rotor at design speed are compared to laser anemometer measurements at maximum flow and near stall operating points. Computational details of the 2-D axisymmetric stream function solution and the 3-D full Euler solution are described. Relative Mach number contours, shock location, and shock strength as measured and as predicted by the 3-D code are compared. Downstream of the rotor the inviscid computations agree with each other but predict higher pressure ratios than those measured. Euler codes require a downstream pressure as input. Since that pressure controls the computed mass flow and shock system, it must be consistent with an inviscid solution.

Chima, R. V.↗