Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “COPPER OXIDES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 991 records · Page 55

Microwave-Assisted Synthesis of Cu@IrO 2 Core-Shell Nanowires for Low-Temperature Methane Conversion

A facile microwave-assisted synthesis was developed for the tunable fabrication of a novel Cu@IrO 2 core@shell nanowire motif. Experimental parameters, such as (i) reaction time, (ii) the method of addition of the Ir precursor, (iii) capping agent, (iv) reducing agent, as well as (v) the capping agent-to-reducing agent ratio, were subsequently optimized. The viability of other methods based on previously reported literature, such as refluxing, stirring, and physical sonication, was studied and compared with our optimized microwave-assisted protocol in creating our as-prepared materials. It should be noted that the magnitude of the IrO 2 shell could be tailored based on varying the Cu: Ir ratio coupled with judicious variations in the amounts of capping agent and reducing agent. Structural characterization techniques, such as XRD, XPS, and HRTEM (including HRTEM-EDS), were used to analyze our Cu@IrO 2 motifs. Specifically, the shell could be reliably tailored from sizes of 10 nm, 8 nm, 6 nm, and 3.5 nm with corresponding Cu: Ir ratios of 10:1, 15:1, 20:1, and 25:1, respectively. Moreover, the structural integrity of the motifs was probed and found to have been maintained after not only heat treatment but also the post-methane conversion process, indicative of an intrinsically high stability. Both components within the CuO-IrO 2 interface were able to activate methane at temperatures between 400 to 500 K with a reduction of the associated metal cations (Cu 2+ → Cu 1+ ; Ir 4+ → Ir 3+ ) and the deposition of CH x fragments on the surface, as clearly observed in the ambient-pressure XPS results. Thus, on the basis of their stability and chemical activity, these core-shell materials could be very useful for the catalytic conversion of methane into 'higher value" chemicals.

36 MATERIALS SCIENCE↗

Observing Chemical and Morphological Changes in a Cu@TiO x Core@Shell Catalyst: Impact of Reversible Metal-Oxide Interactions on CO 2 Activation and Hydrogenation

A combination of several in-situ techniques (XRD, XAS, AP-XPS, E-TEM) was used to explore links between the structural and chemical properties of a Cu@TiO x catalyst under CO 2 hydrogenation conditions. The active phase of the catalyst involved an inverse oxide/metal configuration, but the initial core@shell motif was disrupted during the pre-treatment in H 2 . As a consequence of strong metal-support interactions, the titania shell cracked and Cu particles migrated from the core to on top of the oxide with the simultaneous formation of a Cu-Ti-O x phase. The generated Cu particles had a diameter of 20-40 nm and were decorated by small clusters of TiO x (< 5 nm in size). Results of in-situ XAS and XRD and images of E-TEM showed a very dynamic system, where the inverse oxide/metal configuration promoted the reactivity of the system towards CO 2 and H 2 . At room temperature, CO 2 oxidized the Cu nanoparticles (CO 2,gas → CO gas + O oxide ) inducing a redistribution of the TiO x clusters and big modifications in catalyst surface morphology. The generated oxide overlayer disappeared at elevated temperatures (> 180 °C) upon exposure to H 2 , producing a transient surface that was very active for the reverse water-gas shift reaction (CO 2 + H 2 → CO + H 2 O) but was not stable at 250 °C. When oxidation and reduction occurred at the same time, under a mixture of CO 2 and H 2 , the surface structure evolved toward a dynamic equilibrium that strongly depended on the temperature. Neither CO 2 nor H 2 can be considered as passive reactants. In the Cu@TiO x system, morphological changes were linked to variations in the composition of metal-oxide interfaces which were reversible with temperature or chemical environment and affected the catalytic activity of the system. Finally, the present study illustrates the dynamic nature of phenomena associated with the trapping and conversion of CO 2 .

36 MATERIALS SCIENCE↗

Inverse ZrO 2 /Cu as a highly efficient methanol synthesis catalyst from CO 2 hydrogenation

Enhancing the intrinsic activity and space time yield of Cu based heterogeneous methanol synthesis catalysts through CO 2 hydrogenation is one of the major topics in CO 2 conversion into value-added liquid fuels and chemicals. Here we report inverse ZrO 2 /Cu catalysts with a tunable Zr/Cu ratio have been prepared via an oxalate co-precipitation method, showing excellent performance for CO 2 hydrogenation to methanol. Under optimal condition, the catalyst composed by 10% of ZrO 2 supported over 90% of Cu exhibits the highest mass-specific methanol formation rate of 524 g MeOH kg cat -1 h -1 at 220°C, 3.3 times higher than the activity of traditional Cu/ZrO 2 catalysts (159 g MeOH kg cat -1 h -1 ). In situ XRD-PDF, XAFS and AP-XPS structural studies reveal that the inverse ZrO 2 /Cu catalysts are composed of islands of partially reduced 1–2 nm amorphous ZrO 2 supported over metallic Cu particles. The ZrO 2 islands are highly active for the CO 2 activation. Meanwhile, an intermediate of formate adsorbed on the Cu at 1350 cm -1 is discovered by the in situ DRIFTS. This formate intermediate exhibits fast hydrogenation conversion to methoxy. The activation of CO 2 and hydrogenation of all the surface oxygenate intermediates are significantly accelerated over the inverse ZrO 2 /Cu configuration, accounting for the excellent methanol formation activity observed.

36 MATERIALS SCIENCE↗

Copper-dependent halogenase catalyses unactivated C−H bond functionalization

Carbon–hydrogen (C–H) bonds are the foundation of essentially every organic molecule, making them an ideal place to do chemical synthesis. The key challenge is achieving selectivity for one particular C(sp 3 )−H bond. In recent years, metalloenzymes have been found to perform C(sp 3 )−H bond functionalization. Despite substantial progresses in the past two decades, enzymatic halogenation and pseudohalogenation of unactivated C(sp 3 )−H—providing a functional handle for further modification—have been achieved with only non-haem iron/α-ketoglutarate-dependent halogenases, and are therefore limited by the chemistry possible with these enzymes. Here, in this work, we report the discovery and characterization of a previously unknown halogenase ApnU, part of a protein family containing domain of unknown function 3328 (DUF3328). ApnU uses copper in its active site to catalyse iterative chlorinations on multiple unactivated C(sp 3 )−H bonds. By taking advantage of the softer copper centre, we demonstrate that ApnU can catalyse unprecedented enzymatic C(sp 3 )−H bond functionalization such as iodination and thiocyanation. Using biochemical characterization and proteomics analysis, we identified the functional oligomeric state of ApnU as a covalently linked homodimer, which contains three essential pairs—one interchain and two intrachain—of disulfide bonds. The metal-coordination active site in ApnU consists of binuclear type II copper centres, as revealed by electron paramagnetic resonance spectroscopy. This discovery expands the enzymatic capability of C(sp 3 )−H halogenases and provides a foundational understanding of this family of binuclear copper-dependent oxidative enzymes.

biocatalysis↗

Synthesis of single-site copper catalysts for methane partial oxidation

Cu-Exchanged zeolites are known as active materials for methane oxidation to methanol. However, understanding of the formation of Cu active species during synthesis, dehydration and activation is fragmented and rudimentary. We show here how a synthesis protocol guided by insight in the ion exchange elementary steps leads to highly uniform Cu species in mordenite (MOR).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Thermal removal of mercury in spent powdered activated carbon from TOXECON process

This research developed and demonstrated a technology to liberate Hg adsorbed onto powdered activated carbon (PAC) by the TOXECON process using pilot-scale high temperature air slide (HTAS) and bench-scale thermogravimetric analyzer (TGA). The HTAS removed 65, 83, and 92% of Hg captured with PAC when ran at 900{sup o}F, 1,000{sup o}F, and 1,200 {sup o}F, respectively, while the TGA removed 46 and 100% of Hg at 800 {sup o}F and 900{sup o}F, respectively. However, addition of CuO-Fe{sub 2}O{sub 3} mixture and CuCl catalysts enhanced Hg removal and PAC regeneration at lower temperatures. CuO-Fe{sub 2}O{sub 3} mixture performed better than CuCl in PAC regeneration. Scanning electron microscopy images and energy dispersive X-ray analysis show no change in PAC particle aggregation or chemical composition. Thermally treated sorbents had higher surface area and pore volume than the untreated samples indicating regeneration. The optimum temperature for PAC regeneration in the HTAS was 1,000{sup o}F. At this temperature, the regenerated sorbent had sufficient adsorption capacity similar to its virgin counterpart at 33.9% loss on ignition. Consequently, the regenerated PAC may be recycled back into the system by blending it with virgin PAC.

01 COAL, LIGNITE, AND PEAT↗

Enhanced dielectric response of GeO{sub 2}-doped CaCu{sub 3}Ti{sub 4}O{sub 12} ceramics

CaCu{sub 3}Ti{sub 4}O{sub 12} ceramic samples were prepared by solid state conventional route using stoichiometric amounts of CuO, TiO{sub 2}, and CaCO{sub 3}. Afterward the material was doped with GeO{sub 2} with concentrations up to 6% by weight and sintered at 1050 deg. C for 12 h. The influence of doping on the microstructure, vibrational modes, and dielectric properties of the material was investigated by x-ray diffraction, scanning electron microscopy coupled with an energy dispersive spectrometer, and infrared and dielectric measurements between 100 Hz and 30 MHz. The materials presented huge dielectric response, which increases with doping level relative to undoped CaCu{sub 3}Ti{sub 4}O{sub 12}. The main effect of doping on the microstructure is the segregation of Cu-rich phase in the ceramic grain boundaries. Cole-Cole modeling correlates well the effects of this segregation with the relaxation parameters obtained. The intrinsic phonon contributions for the dielectric response were obtained and discussed together with the structural evolution of the system.

36 MATERIALS SCIENCE↗

Radiation Effects in Binary and Multicomponent Solids

The report deals with damage kinetics, defect evolution and radiation response of binary and multicomponent solids irradiated with MeV electrons. Studies were made into such systems as metallic alloys, semiconductors, high-T{sub c} superconductors and bulk metallic glasses. The common features of the studies involve the efficient use of MeV dc electron beams as generators of point-like defects in solids, precise low-temperature (5-80 K) irradiation conditions, and, as a rule, in situ measurements of irradiated material parameters. To exemplify, successful investigations on the following topics are reported here: (1) Annealing of radiation defects in binary zirconium-base alloys. (2) Impact of defect density on electronic properties of nanocrystalline hydrogenated silicon. (3) Pinning process in high-T{sub c} YBa{sub 2}Cu{sub 3}O{sub 7-x} single crystals irradiated with MeV electrons. (4) Accumulation and recovery kinetics of radiation defects in bulk metallic glasses.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Relative Humidity Sensing Properties Of Cu{sub 2}O Doped ZnO Nanocomposite

In this paper we report application of Cu{sub 2}O doped ZnO composite prepared by solid state reaction route as humidity sensor. Pellet samples of ZnO-Cu{sub 2}O nanocrystalline powders with 2, 5 and 10 weight% of Cu{sub 2}O in ZnO have been prepared. Pellets have been annealed at temperatures of 200-500 deg. C and exposed to humidity. It is observed that as relative humidity increases, resistance of the pellet decreases for the humidity from 10% to 90%. Sample with 5% of Cu{sub 2}O doped in ZnO and annealed at 500 deg. C shows best results with sensitivity of 1.50 M{omega}/%RH. In this case the hysteresis is low and the reproducibility high, making it the suitable candidate for humidity sensing.

36 MATERIALS SCIENCE↗

Morphology, Orientation Relationship and Stability Analysis of Cu2O nanoclusters on SrTiO3 (100)

Reflection high energy electron diffraction (RHEED), atomic force microscopy (AFM) and theoretical studies based on classical nucleation theory have been used to understand the morphology, orientation relationship and stability of Cu2O nanoclusters on SrTiO3 (100) (STO). We propose that the competing interfacial and elastic energies facilitate an in-plane rotation of the Cu2O clusters by 45o with respect to the STO substrate and stabilize Cu2O clusters on STO(100) with an orientation relationship of (001) Cu 2o //(001) SrTiO3 and <100> Cu 2o //<110> SrTiO3. Preliminary theoretical analysis also suggests that this particular orientation results in smaller critical nucleus sizes and lower nucleation barriers. The study also indicates a chemical potential (growth rate) dependence of the orientation relationship.

36 MATERIALS SCIENCE↗

Fabrication of Cu{sub 2}O/TiO{sub 2} nanotube heterojunction arrays and investigation of its photoelectrochemical behavior

Cu{sub 2}O/TiO{sub 2} nanotube heterojunction arrays have been prepared by photoreduction depositing Cu{sub 2}O nanoparticles on TiO{sub 2} nanotube arrays. The heterojunction arrays show uniformly distributed Cu{sub 2}O nanoparticles, and high crystallinity of anatase and cubic from the TiO{sub 2} and Cu{sub 2}O, respectively. The asymmetry of the current-voltage plot for the material reveals that a heterojunction has been formed between TiO{sub 2} and Cu{sub 2}O. Enhanced charge separation efficiency and improved photoconversion capability are confirmed by electrochemical impedance spectroscopy and photocurrent measurement.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Optical Excitations in Insulating CuO{sub 4} Plaquette Networks: Discussion Based on a One Dimensional Mott Insulator Sr{sub 2}CuO{sub 3}

Insulating cuprates become insulator thanks to the strong Coulomb repulsion at Cu d orbitals. They have charge gap between filled oxygen 2p and empty Cu 3d states categorized as charge transfer insulators. Although only Cu 3d and O 2p states are involved in low energy optical transitions, optical excitation spectra of insulating cuprates show rich structures depending on the form of CuO{sub 4} networks. One dimensional chain systems with corner-sharing plaquettes and edge-sharing plaquettes provide basic characters of these transitions. Comparison of available spectra of two dimensional cuprates with one dimensional chain compound Sr{sub 2}CuO{sub 3} suggests that excitonic effect is important in CuO{sub 2} planes.

36 MATERIALS SCIENCE↗

Synchrotron Infrared Microspectroscopy Study of Film Formation and Breakdown on Copper

This work demonstrates the utility of synchrotron infrared reflectance microspectroscopy (SIRM), in the far and mid IR, for the determination of the composition of electrogenerated surface films formed during the general and localized corrosion of copper in bicarbonate solution. The back-reflection geometry was used. The anodic passivation film formed on copper at 0.2 V, in 0.01 M NaHCO{sub 3} solution consisted mainly of bicarbonate, copper carbonate dihydroxide or malachite [CuCO{sub 3}.Cu(OH){sub 2}], Cu(OH){sub 2}, and possibly some CuO. At higher potentials, the passive film breaks down and localized corrosion occurs leading to the formation of pits. The composition of the surface films inside the pits formed at 0.6 V was found to be essentially the same as that outside but the relative amount of Cu(OH){sub 2} is higher.

36 MATERIALS SCIENCE↗

Multilayered Al/CuO thermite formation by reactive magnetron sputtering: Nano versus micro

Multilayered Al/CuO thermite was deposited by a dc reactive magnetron sputtering method. Pure Al and Cu targets were used in argon-oxygen gas mixture plasma and with an oxygen partial pressure of 0.13 Pa. The process was designed to produce low stress (<50 MPa) multilayered nanoenergetic material, each layer being in the range of tens nanometer to one micron. The reaction temperature and heat of reaction were measured using differential scanning calorimetry and thermal analysis to compare nanostructured layered materials to microstructured materials. For the nanostructured multilayers, all the energy is released before the Al melting point. In the case of the microstructured samples at least 2/3 of the energy is released at higher temperatures, between 1036 and 1356 K.

36 MATERIALS SCIENCE↗

Growth And Gas Sensing Properties Of Dielectrophoretically Isolated CuO-W{sub 18}O{sub 49} Heterostructures

Hierarchical heterostructures consisting of W{sub 18}O{sub 49} nanowires grown on CuO nanowires have been prepared and studied for their gas sensing properties. SEM images show that W{sub 18}O{sub 49} initially grow as an shell over core CuO nanowire with protusion like branches whose thickness depends on oxygen partial pressure. These CuO:W{sub 18}O{sub 49} structures were dielectrophoretically isolated and studied for their gas sensing properties. The results show potential of use of tailored hierarchical heterostructures for the fabrication of gas sensors.

36 MATERIALS SCIENCE↗

Sintering dense NiZn ferrite by two-step sintering process

A two-step sintering process has been adopted to produce NiZn ferrite with composition of (NiO){sub 0.35}(ZnO){sub 0.57}(CuO){sub 0.08}(Fe{sub 2}O{sub 3}). The densification, microstructure, and magnetic properties of the ferrite have been investigated and compared with those of ferrites produced by the traditional final-stage sintering process. It was found that the sample produced by a two-step sintering process with a high temperature of 1200 deg. C and a lower temperature of 1100 deg. C attained more than 96% of the theoretical density and had a uniform microstructure with a small average grain size. It also exhibited good performances in terms of permeability and Q-factor. Hence, this would seem to be an effective method for producing dense ferrites with a microstructure composed of small and even grains, which is a very effective strategy for improving the magnetic properties of ferrites.

36 MATERIALS SCIENCE↗