Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “BEAM SHAPING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 991 records · Page 55

Stacking Multiple Ion Captures in The High Performance Antiproton Trap (HiPAT)

The High performance Antiproton Trap (HiPAT) research project was initiated by the Marshall Space Flight Center's propulsion Research Center to examining the fundamental behavior of low energy antiprotons. Stored antiproton would ultimately be used for experimental demonstration of basic propulsive concepts. Matter-antimatter annihilation produces approximately 10(exp 8) MJ/g nearly 10 orders of magnitude more energy per unit mass than chemical based combustion, hence NASA's interest. To achieve containment, HiPAT utilizes a type of electromagnetic bottle know as a Penning trap positioned within an ultrahigh vacuum test section. Recently, the HiPAT hardware configuration has been enhanced to facilitate the capture of multiple normal matter ion burst. This endeavor is often referred to as "stacking" and used to increasing the number of captured particles. A prior normal matter experimental effort, successfully demonstrated the effectiveness of single burst capture. The stacking process is accomplished by manipulating the electric field generated by the confinement electrodes i.e. adjusting the well potential depth. These potential well values are initially configured to maximize the quantity of captured ions per burst; shallow wells with a depth of 100 volt or less (referenced to the incoming ion beam energy) are typically selected. Once captured, a cooling interval is required to reduce the energy of trapped particles below the lower extent of the "trap door" (or leading electrode) ion emitting potential. This is necessary such that a new burst of hot ions can be introduced while preventing those already inside from escaping. The cooling time is driven by a combination of mechanisms such as synchrotron radiation, background gas scattering, and resistive damping in a time scale on the order of minutes. A potential for reducing this hold period is to actively manipulate the electric field shape, using the power supply control system, to produce a deeper potential well. The trapped ions ride down the morphing well to a lower potential energy, leaving margin to once again cycle the "trap door" capturing a new burst while limiting the number of escaping ions. By adjusting the magnitude and timing of the potential well shaping, subsequent shots from the ion beam can be captured on a time scale shorter then that dictated by the standard inject, capture and cool technique. Currently, experimental tests are under way examining the functionally of this system for stacking multiple ions bursts within the HiPAT system.

Martin, James J.↗

Steering of Multiple Beamlets in the JT-60 U Negative Ion Source

The direct interception of D{sup -} ion beam by the acceleration grid was reduced by modifying field shaping plates (FSPs) in JT-60 negative ion sources to inject powerful neutral beams for long pulse duration of >10 s. The modified FSPs are designed by a 3D simulation code to properly steer the outermost beamlets that are deflected outward by space charge of the inward beamlets. The measured steering angles were -1.2 mrad and -6.4/-4.5 mrad in the vertical and horizontal direction, which were in agreement with the designed value calculated by the 3D simulation code. The proper steering of the outermost beamlets allowed a significant reduction of the power loading of the grounded grid. The power loading was successfully reduced to an allowable level of 5% with respect to the acceleration beam power.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Monte Carlo linear accelerator simulation of megavoltage photon beams: Independent determination of initial beam parameters

Purpose: To individually benchmark the incident electron parameters in a Monte Carlo model of an Elekta linear accelerator operating at 6 and 15 MV. The main objective is to establish a simplified but still precise benchmarking procedure that allows accurate dose calculations of advanced treatment techniques. Methods: The EGSnrc Monte Carlo user codes BEAMnrc and DOSXYZnrc are used for photon beam simulations and dose calculations, respectively. A 5 x 5 cm{sup 2} field is used to determine both the incident electron energy and the electron radial intensity. First, the electron energy is adjusted to match the calculated depth dose to the measured one. Second, the electron radial intensity is adjusted to make the calculated dose profile in the penumbrae region match the penumbrae measured by GafChromic EBT film. Finally, the mean angular spread of the incident electron beam is determined by matching calculated and measured cross-field profiles of large fields. The beam parameters are verified for various field sizes and shapes. Results: The penumbrae measurements revealed a non-circular electron radial intensity distribution for the 6 MV beam, while a circular electron radial intensity distribution could best describe the 15 MV beam. These electron radial intensity distributions, given as the standard deviation of a Gaussian distribution, were found to be 0.25 mm (in-plane) and 1.0 mm (cross-plane) for the 6 MV beam and 0.5 mm (both in-plane and cross-plane) for the 15 MV beam. Introducing a small mean angular spread of the incident electron beam has a considerable impact on the lateral dose profiles of large fields. The mean angular spread was found to be 0.7 deg. and 0.5 deg. for the 6 and 15 MV beams, respectively. Conclusions: The incident electron beam parameters in a Monte Carlo model of a linear accelerator could be precisely and independently determined by the benchmarking procedure proposed. As the dose distribution in the penumbra region is insensitive to moderate changes in electron energy and angular spread, accurate penumbra measurements is feasible for benchmarking the electron radial intensity distribution. This parameter is particularly important for accurate dosimetry of mlc-shaped fields and small fields.

43 PARTICLE ACCELERATORS↗

Particle Production Measurements Using the MIPP Detector at Fermilab

Inelastic cross sections have been measured for H, Be, C and Bi targets using proton beams at momenta of 58, 85 and 120 GeV/c using the MIPP experiment at Fermilab. The cross section dependence on the atomic weight (A) of the targets has been found to vary as A$^{\alpha}$, where $\alpha$ is 0.75 $\pm$ 0.03 for a beam momentum of 58 GeV/c and 0.66 $\pm$ 0.03 for 120 GeV/c. The MIPP data have been compared with the Monte Carlo (DPMJET/FLUKA) predictions and previous measurements. Inelastic cross sections have also been measured as a function of multiplicity for H and C targets using proton beams at different momenta. The DPMJET/FLUKA multiplicity shapes disagree with those of data. Inclusive charged pion production cross sections have also been measured in bins of true momentum for C target using 58 and 120 GeV/c proton beams, and compared with the FLUKA Monte Carlo.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Nanocrystalline Ba{sub 0.97}Ca{sub 0.03}SO{sub 4}:Eu for ion beams dosimetry

Nanoparticles of Ba{sub 0.97}Ca{sub 0.03}SO{sub 4}:Eu have been irradiated by 48 MeV Li{sup 3+}, 75 MeV C{sup 6+}, and 90 MeV O{sup 7+} ion beams with a fluence range of 1x10{sup 9}-1x10{sup 13} ion/cm{sup 2}. The thermoluminescence (TL) glow curves along with the response curves of this nanophosphor have been investigated and compared with those of the corresponding microcrystalline samples. TL glow curve of the nanophosphor exposed to {gamma}-rays has also been included in the letter with the aim of reporting some of the comparative measurements. The glow curves of the ion-beam irradiated nanomaterials are similar in their shapes to those induced by gamma rays, with a shift in the peak positions to the higher temperature side by around 30 K. The TL intensity of the ion-beam irradiated nanomaterials is found to decrease, while going from low to high atomic number (Z) ions (i.e., Li{sup 3+}{yields}O{sup 7+}). Similar trend was also observed in the linearity of the TL response curves. The response curve of Li ion irradiated nanomaterials is sublinear in the whole range of studied fluences. C ion has also a more or less similar response, while the O ion has a sublinear response over a shorter range of 1x10{sup 9}-1x10{sup 12} ion/cm{sup 2}, and above this range the response saturates. These results for the nanomaterials are much better than that of the corresponding microcrystalline sample irradiated by Li{sup 3+} ions. The curve was sublinear up to the fluence 1x10{sup 10} ion/cm{sup 2} and then saturates at higher fluences. The wider sublinear TL response of the nanocrystalline Ba{sub 0.97}Ca{sub 0.03}SO{sub 4}:Eu makes it superior to its corresponding microform and thus makes it a suitable candidate as a dosimeter to be used for detecting the doses of ions, especially the Li and C ions for their application in cancer radiotherapy and radiation biology.

36 MATERIALS SCIENCE↗

A fast parallel Poisson solver on irregular domains applied to beam dynamics simulations

We discuss the scalable parallel solution of the Poisson equation within a Particle-In-Cell (PIC) code for the simulation of electron beams in particle accelerators of irregular shape. The problem is discretized by Finite Differences. Depending on the treatment of the Dirichlet boundary the resulting system of equations is symmetric or 'mildly' nonsymmetric positive definite. In all cases, the system is solved by the preconditioned conjugate gradient algorithm with smoothed aggregation (SA) based algebraic multigrid (AMG) preconditioning. We investigate variants of the implementation of SA-AMG that lead to considerable improvements in the execution times. We demonstrate good scalability of the solver on distributed memory parallel processor with up to 2048 processors. We also compare our iterative solver with an FFT-based solver that is more commonly used for applications in beam dynamics.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Polarization effects in thallium bromide x-ray detectors

We present the results of a detailed experimental study of polarization effects in thallium bromide planar x-ray detectors. Measurements were carried out in the range 10-100 keV by scanning a highly focused x-ray beam, 50 {mu}m in diameter, from a synchrotron source across the detector. Above a certain radiation threshold the detector response showed a systematic degradation of its spectroscopic characteristics, peak channel position, peak height, and energy resolution. Using a pump-and-probe technique, we studied the dynamics of spectral degradation, the spatial extent and relaxation of the polarized region, and the dependence of the detector response on bias voltage and temperature. For comparison, we modeled polarization effects induced by the charging of traps by both electrons and holes using a model based on recent theoretical work of Bale and Szeles. We calculated the charge collection efficiency and spectral line shapes as functions of exposure time, beam position, count rate, and photon energy, and obtained credible agreement with experimental results.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Wedge Absorber Design for the Muon Ionisation Cooling Experiment

In the Muon Ionisation Cooling Experiment (MICE), muons are cooled by ionisation cooling. Muons are passed through material, reducing the total momentum of the beam. This results in a decrease in transverse emittance and a slight increase in longitudinal emittance, but overall reduction of 6d beam emittance. In emittance exchange, a dispersive beam is passed through wedge-shaped absorbers. Muons with higher energy pass through more material, resulting in a reduction in longitudinal emittance as well as transverse emittance. We consider the cooling performance of different wedge materials and geometries and propose a set of measurements that would be made in MICE.We outline the resources these measurements would require and detail some constraints that guide the choice of wedge parameters.

43 PARTICLE ACCELERATORS↗

The effect of residual gas scattering on Ga ion beam patterning of graphene

The patterning of graphene by a 30 kV Ga{sup +} focused ion beam (FIB) is studied by in-situ and ex-situ Raman spectroscopy. It is found that the graphene surrounding the patterned target area can be damaged at remarkably large distances of more than 10 μm. We show that scattering of the Ga ions in the residual gas of the vacuum system is the main cause of the large range of lateral damage, as the size and shape of the tail of the ion beam were strongly dependent on the system background pressure. The range of the damage was therefore greatly reduced by working at low pressures and limiting the total amount of ions used. This makes FIB patterning a feasible alternative to electron beam lithography as long as residual gas scattering is taken into account.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

The dynamics and control of large-flexible space structures, part 10

A mathematical model is developed to predict the dynamics of the proposed orbiting Spacecraft Control Laboratory Experiment (SCOLE) during the station keeping phase. The equations of motion are derived using a Newton-Euler formulation. The model includes the effects of gravity, flexibility, and orbital dynamics. The control is assumed to be provided to the system through the Shuttle's three torquers, and through six actuators located by pairs at two points on the mast and at the mass center of the reflector. The modal shape functions are derived using the fourth order beam equation. The generic mode equations are derived to account for the effects of the control forces on the modal shape and frequencies. The equations are linearized about a nominal equilibrium position. The linear regulator theory is used to derive control laws for both the linear model of the rigidized SCOLE as well as that of the actual SCOLE including the first four flexible modes. The control strategy previously derived for the linear model of the rigidized SCOLE is applied to the nonlinear model of the same configuration of the system and preliminary single axis slewing maneuvers conducted. The results obtained confirm the applicability of the intuitive and appealing two-stage control strategy which would slew the SCOLE system, as if rigid to its desired position and then concentrate on damping out the residual flexible motions.

Bainum, Peter M.↗

Spectral shape of a signal in light-induced diffusive pulling (pushing) of particles into a light beam

We study theoretically how the dependences of transport collision frequencies ν{sub i}, collision broadening γ and collision shift Δ of the levels on the velocity v of resonant particles influence lightinduced diffusive pulling (pushing) (LDP) effects in the framework of a generalised model of strong collisions in the case of velocitydependent collision rates (so-called kangaroo model). It is found that allowance for the dependences ν{sub i}(v), γ(v) and Δ(v) does not change the spectral shape of an LDP signal. In particular, in the case of low-intensity radiation, the spectral dependence of the LDP signal coincides with the absorption line shape. It is shown that the magnitude of the LDP effect is proportional to the difference between the diffusion coefficients of particles in the excited and ground states. It is found that the spectral anomalies previously predicted in the LDP effect [Gel'mukhanov F.Kh. JETP Lett., 55, 214 (1992)] for an idealised model of the Lorentz gas (the limiting case of heavy buffer particles), which arise due to the dependences ν{sub i}(v), γ(v) and Δ(v), are typical only for this gas. At a realistic ratio of the masses of absorbing and buffer particles, spectral anomalies do not occur in the LDP effect. (nonlinear optical phenomena)

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Compact particle accelerator

A compact particle accelerator having an input portion configured to receive power to produce particles for acceleration, where the input portion includes a switch, is provided. In a general embodiment, a vacuum tube receives particles produced from the input portion at a first end, and a plurality of wafer stacks are positioned serially along the vacuum tube. Each of the plurality of wafer stacks include a dielectric and metal-oxide pair, wherein each of the plurality of wafer stacks further accelerate the particles in the vacuum tube. A beam shaper coupled to a second end of the vacuum tube shapes the particles accelerated by the plurality of wafer stacks into a beam and an output portion outputs the beam.

43 PARTICLE ACCELERATORS↗

Optimization of convergent collimators for pixelated SPECT systems

Purpose: The optimization of the collimator design is essential to obtain the best possible sensitivity in single photon emission computed tomography imaging. The aim of this work is to present a methodology for maximizing the sensitivity of convergent collimators, specifically designed to match the pitch of pixelated detectors, for a fixed spatial resolution value and to present some initial results using this approach. Methods: Given the matched constraint, the optimal collimator design cannot be simply found by allowing the highest level of septal penetration and spatial resolution consistent with the imposed restrictions, as it is done for the optimization of conventional collimators. Therefore, an algorithm that interactively calculates the collimator dimensions, with the maximum sensitivity, which respect the imposed restrictions was developed and used to optimize cone and fan beam collimators with tapered square-shaped holes for low (60-300 keV) and high energy radiation (300-511 keV). The optimal collimator dimensions were locally calculated based on the premise that each hole and septa of the convergent collimator should locally resemble an appropriate optimal matched parallel collimator. Results: The optimal collimator dimensions, calculated for subcentimeter resolutions (3 and 7.5 mm), common pixel sizes (1.6, 2.1, and 2.5 mm), and acceptable septal penetration at 140 keV, were approximately constant throughout the collimator, despite their different hole incidence angles. By using these input parameters and a less strict septal penetration value of 5%, the optimal collimator dimensions and the corresponding mass per detector area were calculated for 511 keV. It is shown that a low value of focal distance leads to improvements in the average sensitivity at a fixed source-collimator distance and resolution. The optimal cone beam performance outperformed that of other optimal collimation geometries (fan and parallel beam) in imaging objects close to the collimator surface. Conclusions: These results demonstrate the potential of this kind of optimal convergent collimators for the use in small field of view imaging applications.

43 PARTICLE ACCELERATORS↗

Simplified modeling for wind turbine modal analysis using NASTRAN

A detailed finite element model of the MOD-0 wind turbine tower was reduced to six beam elements (stick model). The method used to calculate the properties of the beam elements in the stick model was explained and the accuracy of the stick model in predicting natural frequencies and mode shapes was examined. Computer times were compared and several applications where the stick model was used are described. From results obtained from the MOD-0 tower it is concluded that a tower of this type can be modeled as a simple cantilever beam for modal analysis. However, this model should be limited to tower torsional modes and tower bending modes where the mode shape resembles a cantilever beam first bending mode shape.

Sullivan, T. L.↗

A global-local approach to solving vibration of large truss structures

A global-local approach was proposed to solve dynamic problems involving truss beams. A continuum Timoshenko beam was used to model sections of truss beams wherever possible and accurate. Near applied loads the continuum model was not adequate and detailed truss finite elements (discrete model) were employed. This approach was also proven efficient for an odd-shaped truss structure connected to a truss beam. Between the continuum model and the discrete model, compatibility conditions were derived.

Sun, C. T.↗

SU-E-T-146: Beam Energy Spread Estimate Based On Bragg Peak Measurement

Purpose: ProNova is installing and commissioning a two room proton therapy system in Knoxville, TN. Beam energy out of the 230MeV cyclotron was measured on Jan 24, 2015. Cyclotron beam was delivered into a Zebra multi layered IC detector calibrated in terms of penetration range in water. The analysis of the measured Bragg peak determines penetration range in water which can be subsequently converted into proton beam energy. We extended this analysis to obtain an estimate of the beam energy spread out of the cyclotron. Methods: Using Monte Carlo simulations we established the correlation between Bragg peak shape parameters (width at 50% and 80% dose levels, distal falloff) and penetration range for a monoenergetic proton beam. For large uniform field impinging on a small area detector, we observed linear dependence of each Bragg peak parameter on beam penetration range as shown in Figure A. Then we studied how this correlation changes when the shape of Bragg peak is distorted by the beam focusing conditions. As shown in Figure B, small field size or diverging beam cause Bragg peak deformation predominantly in the proximal region. The distal shape of the renormalized Bragg peaks stays nearly constant. This excludes usage of Bragg peak width parameters for energy spread estimates. Results: The measured Bragg peaks had an average distal falloff of 4.86mm, which corresponds to an effective range of 35.5cm for a monoenergetic beam. The 32.7cm measured penetration range is 2.8cm less. Passage of a 230MeV proton beam through a 2.8cm thick slab of water results in a ±0.56MeV energy spread. As a final check, we confirmed agreement between shapes of the measured Bragg peak and one generated by Monte-Carlo code for proton beam with 0.56 MeV energy spread. Conclusion: Proton beam energy spread can be estimated using Bragg peak analysis.

60 APPLIED LIFE SCIENCES↗

Template assisted self-assembly of iron oxide nanoparticles: An x-ray structural analysis

We have fabricated by e-beam lithography periodic arrays of rectangular shaped trenches of different widths into Si substrates. The trenches were filled with iron oxide nanoparticles, 20 nm in diameter, by spin-coating them onto the Si substrate. The trenches have the purpose to assist the self-assembly of the iron oxide nanoparticles. Using x-ray scattering techniques, we have analyzed the structure factor of the trenches before and after filling in order to determine the filling factor. We present a theoretical analysis of the x-ray scattering function within the distorted-wave Born approximation and we present a quantitative comparison between theory and experiment.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗