Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “AXIAL RATIO”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 991 records · Page 55
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Idealized tip-to-tail waverider model

The flow field of an idealized cone-derived waverider is axisymmetric. This forebody feature is preserved for the rest of the vehicle, including the inlet, cowl, combustor, and nozzle. There is thus an inviscid, tip-to-tail model in which both the external and internal flows are axisymmetric. The assumption of axial symmetry provides a major simplification for the analysis and allows for a systematic integration of the propulsion unit with the aerodynamics. The code is an initial formulation that provides only the most basic engineering data, such as lift, thrust, drag, and fuel consumption for a point-designed vehicle that may be cruising at a low hypersonic Mach number. The user may specify flight altitude and Mach number, a multiple shock configuration for the inlet, a few basic geometric parameter, H2 or CH4 as fuel, the fuel/air ratio, etc. A new design concept is used for the nozzle that avoids shock waves, minimizes the nozzle length, and may maximize its thrust. A general description of the model is provided with emphasis on the design of the nozzle and fins. Preliminary results are presented that compare the cruise flight range using H2 or CH4 as the fuel.

Emanuel, G.↗
NASA NTRS1938

The Crinkling Strength and the Bending Strength of Round Aircraft Tubing

The upper limit of the column strength of structural members composed of thin material is the maximum axial stress such members can carry when short enough to fail locally, by crinkling. This stress is a function of the mechanical properties of the material and of the geometrical shape of the cross section. The bending strength, as measured by the modulus of rupture, of structural members is also a function of these same variables. Tests were made of round tubes of chromium-molybdenum steel and of duralumin to determine the crinkling strengths and the bending strengths in terms of the specified yield strength and the ratio of diameter to thickness. Empirical formulas are given relating these quantities.

Osgood, William R↗
NASA NTRS1994

Shear coaxial injector instability mechanisms

There is no definitive knowledge of which of several concurrent processes ultimately results in unstable combustion within liquid rocket chambers employing shear coaxial injectors. Possible explanations are a detrimental change in the atomization characteristics due to a decrease in the gas-to-liquid velocity ratio, a change in the gas side injector pressure drop allowing acoustic coupling to the propellant feed system or the disappearance of a stabilizing recirculation region at the base of the LOX post. The aim of this research effort is to investigate these proposed mechanisms under conditions comparable to actual engine operation. Spray characterization was accomplished with flash photography and planar laser imaging to examine the overall spray morphology and liquid jet breakup processes and with a PDPA to quantify the spatial distribution of droplet size and mean axial velocity. A simplified stability model based on the Rayleigh criterion was constructed for the flow dynamics occurring within the chamber and injector to evaluate the potential coupling between the chamber and injector acoustic modes and was supported by high frequency measurements of chamber and injector pressure oscillations. To examine recirculation within the LOX post recess, velocity measurements were performed in the recess region by means of LDV. Present experiments were performed under noncombusting conditions using LOX/GH2 stimulants at pressures up to 4 MPa.

Puissant, C.↗
NASA NTRS1983

A theory of rotating stall of multistage axial compressors. III - Limit cycles

A theory of rotating stall, based on single parameters for blade-passage lag and external-flow lag and a given compressor characteristic yields limit cycles in velocity space. These limit cycles are governed by Lienard's equation with the characteristic playing the role of nonlinear damping function. Cyclic integrals of the solution determine stall propagation speed and the effect of rotating stall on average performance. Solution with various line-segment characteristics and various throttle settings are found and discussed. There is generally a limiting flow coefficient beyond which no solution is possible; this probably represents stall recovery. This recovery point is independent of internal compressor lag, but does depend on external lags and on the height-to-width ratio of the diagram. Tall diagrams and small external lags (inlet and diffusor) favor recovery. Suggestions for future theoretical and experimental research are discussed.

Moore, F. K.↗
NASA NTRS1988

Particle-laden weakly swirling free jets: Measurements and predictions

A theoretical and experimental investigation of particle-laden, weakly swirling, turbulent free jets was conducted. Glass particles, having a Sauter mean diameter of 39 microns with a standard deviation of 15 microns, were used. A single loading ratio of 0.2 was used in the experiments. Measurements are reported for three swirl numbers, ranging from 0.0 to 0.3. The measurements included mean and fluctuating velocities of both phases, and particle mass flux distributions. Measurements were compared with predictions from three types of multiphase flow analysis: locally homogeneous flow (LHF); deterministic separated flow (DSF); and stochastic separated flow (SSF). For the particle-laden jets, the LHF and DSF models did not provide very satisfactory predictions. The LHF model generally overestimated the rate of decay of particle mean axial and angular velocities with streamwise distance, due to the neglect of particle inertia. The LHF model predictions of particle mass flux also showed poor agreement with measurements due to the assumption of no-slip between phases. The DSF model also performed quite poorly for predictions of particle mass flux, because turbulent dispersion of the particles was neglected. The SSF model, which accounts for both particle inertia and turbulent dispersion of the particles, yielded reasonably good predictions throughout the flow field for the particle-laden jets.

Bulzan, Daniel L.↗
NASA NTRS1988

Particle-laden weakly swirling free jets - Measurements and predictions

A theoretical and experimental investigation of particle-laden, weakly swirling, turbulent free jets was conducted. Glass particles, having a Sauter mean diameter of 39 microns with a standard deviation of 15 microns, were used. A single loading ratio of 0.2 was used in the experiments. Measurements are reported for three swirl numbers, ranging from 0.0 to 0.3. The measurements included mean and fluctuating velocities of both phases, and particle mass flux distributions. Measurements were compared with predictions from three types of multiphase flow analysis: locally homogeneous flow (LHF); deterministic separated flow (DSF); and stochastic separated flow (SSF). For the particle-laden jets, the LHF and DSF models did not provide very satisfactory predictions. The LHF model generally overestimated the rate of decay of particle mean axial and angular velocities with streamwise distance, due to the neglect of particle inertia. The LHF model predictions of particle mass flux also showed poor agreement with measurements due to the assumption of no-slip between phases. The DSF model also performed quite poorly for predictions of particle mass flux, because turbulent dispersion of the particles was neglected. The SSF model, which accounts for both particle inertia and turbulent disperison of the particles, yielded reasonably good predictions throughout the flow field for the particle-laden jets.

Bulzan, Daniel L.↗
NASA NTRS1950

Investigation of Effects of Inlet-air Velocity Distortion on Performance of Turbojet Engine

To determine effect of nonuniform inlet-air velocities, a full scale, axial-flow turbojet engine was investigated in Lewis altitude wind tunnel at altitudes from 20,000 to 50,000 feet, 0.21 flight Mach number and corrected engine speeds from 77.3 percent of rated speed to rated speed. Total-pressure variations as large as 103 pounds per square foot in radial direction and 90 pounds per square foot in circumferential direction at 30,000 feet were obtained. With the distortions investigated, net thrust varied between 0.95 and 1.03 of the thrust with uniform inlet-air distribution. Similarly the ratio of specific fuel consumption varied from 1.00 to 1.04. Within the arrange of this investigation the effects of nonuniform inlet velocity were not serious for the engine investigated.

AIR INLETS↗
NASA NTRS1992

Experimental Investigation of the Behavior of Sub-Grid Scale Motions in Turbulent Shear Flow

Experiments have been carried out on a vertical jet of helium issuing into a co-flow of air at a fixed exit velocity ratio of 2.0. At all the experimental conditions studied, the flow exhibits a strong self excited periodicity. The natural frequency behavior of the jet, the underlying fine-scale flow structure, and the transition to turbulence have been studied over a wide range of flow conditions. The experiments were conducted in a variable pressure facility which made it possible to vary the Reynolds number and Richardson number independently. A stroboscopic schlieren system was used for flow visualization and single-component Laser Doppler Anemometry was used to measure the axial component of velocity. The flow exhibits several interesting features. The presence of co-flow eliminates the random meandering typical of buoyant plumes in a quiescent environment and the periodicity of the helium jet under high Richardson number conditions is striking. Under these conditions transition to turbulence consists of a rapid but highly structured and repeatable breakdown and intermingling of jet and freestream fluid. At Ri = 1.6 the three-dimensional structure of the flow is seen to repeat from cycle to cycle. The point of transition moves closer to the jet exit as either the Reynolds number or the Richardson number increases. The wavelength of the longitudinal instability increases with Richardson number. At low Richardson numbers, the natural frequency scales on an inertial time scale. At high Richardson number the natural frequency scales on a buoyancy time scale. The transition from one flow regime to another occurs over a narrow range of Richardson numbers from 0.7 to 1. A buoyancy Strouhal number is used to correlate the high Richardson number frequency behavior.

Cantwell, Brian↗
DOE OSTI2020

Enhancing easy-plane anisotropy in bespoke Ni(II) quantum magnets

We examine the crystal structures and magnetic properties of several S = 1 Ni(II) coordination compounds, molecules and polymers, that include the bridging ligands HF 2 - , A F 6 2- ( A = Ti, Zr) and pyrazine or non-bridging ligands F - , SiF 6 2- , glycine, H 2 O, 1-vinylimidazole, 4-methylpyrazole and 3-hydroxypyridine. Pseudo-octahedral NiN 4 F 2 , NiN 4 O 2 or NiN 4 OF cores consist of equatorial Ni-N bonds that are equal to or slightly longer than the axial Ni- L ax bonds. By design, the zero-field splitting ( D ) is large in these systems and, in the presence of substantial exchange interactions ( J ), can be difficult to discriminate from magnetometry measurements on powder samples. Thus, we relied on pulsed-field magnetization in those cases and employed electron-spin resonance (ESR) to confirm D when J ← D . The anisotropy of each compound was found to be easy-plane ( D > 0) and range from ≈ 8–25 K. This work reveals a linear correlation between the ratio d (Ni- L ax )/ d (Ni-N eq ) and D although the ligand spectrochemical properties may play an important role. We assert that this relationship allows us to predict the type of magnetocrystalline anisotropy in tailored Ni(II) quantum magnets.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
NASA NTRS1976

Effects of four inlet and outlet tip-annulus-area blockage configurations on the performance of an axial-flow fan rotor

An axial-flow fan rotor was tested with four configurations of tip-annulus-area blockage to speeds as high as 0.8 of design speed. The rotor performance with the four blockage configurations is compared with the unblocked rotor performance and with blockage configurations previously investigated. The blockage configurations enable the rotor to operate in a stable condition, to much lower flows than the unblocked rotor, with no evidence of rotating stall. The blockage configurations were effective in reducing rotor torque and weight flow but were accompanied by reductions in pressure ratio and efficiency.

Osborn, W. M.↗
NASA NTRS1947

Vibration Survey of Blades in 19XB Axial-Flow Compressor: Dynamic Investigation - 2

Strain-gage measurements were taken under operating conditions from blades of various stages of the 19XB axial-flow compressor in an effort to determine the reason for failures in the seventh and tenth stages. First bending-mode vibrations were detected in the first five stages of the compressor caused by each integral multiple of rotor speed from three through ten. Lead-wire failures in the last five stages resulted in incomplete data. The dynamic-vibration frequencies at various rotor speeds were compared with statically measured frequencies analytically corrected for the influence of centrifugal force. Large increases in vibration ani~litude with increased pressure ratio were observed. During surging operation, blade vibrations were not present. The effects of pressure ratio and surge indicate the existence of aerodynamic excitation as the cause of the blade vibrations.

Meyer, Andre J., Jr.↗
NASA NTRS1949

Two-dimensional compressible flow in turbomachines with conic flow surfaces

A general method of analysis is developed for two-dimensional, steady, compressible flow in stators or rotors of radial and mixed flow turbomachines with conic flow surfaces (surfaces of right circular cones generated by center line of flow passage in the axial-radial plane). The variables taken into account are: (1) tip speed of the rotor, (2) flow rate, (3) blade shape, (4) variation in passage height with radius, (5) number of blades, and (6) cone angle of the flow surface. Relaxation methods are used to solve the nonlinear differential equation for the stream function. Two numerical examples are presented; one for compressible and the other for incompressible flow in a centrifugal compressor with thin, straight blades. The results of these examples are given by plots of the streamlines, constant velocity-ratio lines, and constant pressure-ratio line.

Stanitz, John D↗
NASA NTRS1961

Analysis of Heat Transfer and Pressure Drop for a Gas Flowing Through a set of Multiple Parallel Flat Plates at High Temperatures

Equations were derived representing heat transfer and pressure drop for a gas flowing in the passages of a heater composed of a series of parallel flat plates. The plates generated heat which was transferred to the flowing gas by convection. The relatively high temperature level of this system necessitated the consideration of heat transfer between the plates by radiation. The equations were solved on an IBM 704 computer, and results were obtained for hydrogen as the working fluid for a series of cases with a gas inlet temperature of 200 R, an exit temperature of 5000 0 R, and exit Mach numbers ranging from 0.2 to O.8. The length of the heater composed of the plates ranged from 2 to 4 feet, and the spacing between the plates was varied from 0.003 to 0.01 foot. Most of the results were for a five- plate heater, but results are also given for nine plates to show the effect of increasing the number of plates. The heat generation was assumed to be identical for each plate but was varied along the length of the plates. The axial variation of power used to obtain the results presented is the so-called "2/3-cosine variation." The boundaries surrounding the set of plates, and parallel to it, were assumed adiabatic, so that all the power generated in the plates went into heating the gas. The results are presented in plots of maximum plate and maximum adiabatic wall temperatures as functions of parameters proportional to f(L/D), for the case of both laminar and turbulent flow. Here f is the Fanning friction factor and (L/D) is the length to equivalent diameter ratio of the passages in the heater. The pressure drop through the heater is presented as a function of these same parameters, the exit Mach number, and the pressure at the exit of the heater.

Einstein, Thomas H.↗
NASA NTRS2004

Magnetic and Langmuir Probe Measurements on the Plasmoid Thruster Experiment (PTX)

The Plasmoid Thruster Experiment (PTX) operates by inductively producing plasmoids in a conical theta-pinch coil and ejecting them at high velocity. A plasmoid is a plasma with an imbedded closed magnetic field structure. The shape and magnetic field structure of the translating plasmoids have been measured with of an array of magnetic field probes. Six sets of two B-dot probes were constructed for measuring B(sub z) and B(sub theta), the axial and azimuthal components of the magnetic field. The probes are wound on a square G10 form, and have an average (calibrated) NA of 9.37 x l0(exp -5) square meters, where N is the number of turns and A is the cross-sectional area. The probes were calibrated with a Helmholtz coil, driven by a high-voltage pulser to measure NA, and by a signal generator to determine the probe's frequency response. The plasmoid electron number density n(sub e) electron temperature T(sub e), and velocity ratio v/c(sub m), (where v is the bulk plasma flow velocity and c(sub m), is the ion thermal speed) have also been measured with a quadruple Langmuir probe. The Langmuir probe tips are 10 mm long, 20-mil diameter stainless steel wire, housed in a 6-inch long 4-bore aluminum rod. Measurements on PTX with argon and hydrogen from the magnetic field probes and quadruple Langmuir probe will be presented in this paper.

Koelfgen, Syri J.↗
DOE OSTI2019

Kinetic Study on Alloying Element Transfer During an Electroslag Remelting Process

Experimental and theoretical studies have been carried out to investigate the effects of slag on the alloying elements in ingots during the electroslag remelting (ESR) process with a focus on developing a mass-transfer model to understand the mechanism of slag-metal reaction. Stainless steel 1Cr21Ni5Ti was used as the electrode and remelted with two different kinds of slags using a 50-kg ESR furnace. The contents of sulfur, aluminum, titanium and silicon along the axial direction of the produced ingots were analyzed. On the basis of the penetration and film theories, the theoretical model developed in this work elucidates the kinetics of the slag-metal reaction revealing the mechanism of alloying element transfer during the ESR process. The calculation results obtained from the model agree well with the experimental results. The model indicates that the resultant [O] coming from the desulfurization reaction of (O{sup 2−}) + [S] = (S{sup 2−}) + [O] causes the oxidation of alloying elements in steel by [M] + [O] = (MO). The distribution ratio of sulfur L{sub S} decreases with the increase of slag temperature in the first slag-temperature-rising period, and the concentration of sulfur in the ingot at the beginning of the ESR process is lower than in the rest of the process because of the combination of the large distribution ratio of sulfur L{sub S} and excellent kinetic conditions. The concentration of aluminum along the height of the ingot has an increasing trend in the first slag-temperature-rising period, while it has a decreasing trend in the rest of the process. Two methods can solve this problem: one is starting up the ESR furnace by high temperature molten slag technology and the other is continually adding extra titania into the molten slag in the first slag-temperature-rising period.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Twin Proliferation and Prolongation under Kinetic Control: Pd–Au Janus Icosahedra versus Pd@Au Core–Shell Starfishes

Heterogeneous bimetallic nanocrystals featuring explicit spatial configurations and abundant twin defects can simultaneously enable geometric and ligand effects to enhance catalytic and photonic applications. Herein, we report two growth patterns of Au atoms on penta-twinned Pd decahedra, involving twin proliferation to generate asymmetric Pd–Au Janus icosahedra and twin elongation to produce anisotropic Pd@Au core–shell starfishes, respectively. Mechanistic analysis indicates that the injection rate determines the lower-limit number (n low ) of Au(III) ions in the steady state and thus controls the growth pattern. When n low ≤ 5.5, the kinetic rate is slow enough to initiate asymmetrical one-side growth but fast enough to outpace surface diffusion; Au tetrahedral subunits are successively proliferated along the axial $\langle$110$\rangle$ direction of Pd decahedra to form Pd–Au Janus icosahedra. Composed of five Pd and 15 Au tetrahedral subunits, such a heterogeneous icosahedron supports high (2.2 GPa) tensile strain and high strain difference up to +21.9%. In contrast, when n low > 5.5, the fast reduction kinetics promotes symmetric growth with inadequate surface diffusion. As such, Au atoms are laterally deposited along five high-indexed $\langle$211$\rangle$ ridges of Pd decahedra to generate concave Pd@Au core–shell starfishes with tunable sizes (28–40 nm), twin elongation ratios (33.82–162.08%), and lattice expansion ratios (8.82–20.10%).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Optimal load attachment of a deeply embedded ring anchor in clay

A Deeply Embedded Ring Anchor (DERA) system has been developed as a cost-effective solution for mooring arrays of floating offshore wind turbines (FOWTs) to the seabed. The DERA boasts several key features, including its versatility in various soil types, compact size, compatibility with diverse mooring systems, multi-line potential, and robust performance even under unintentional loading conditions. While prior preliminary studies have provided valuable insights into how the DERA can enhance cost-effectiveness by offering a high load capacity, these studies have predominantly focused on optimizing anchor performance under translational horizontal and vertical loading. However, to design the DERA optimally, we must also consider its ability to handle inclined loading conditions in addition to lateral and axial loadings. Due to its shorter length compared to a conventional caisson, the DERA has less resistance to moments, making it more sensitive to horizontal load capacity and the optimal load attachment depth concerning load angle. For this reason, our study introduces an analytical approach to evaluate the effects of inclined loading on anchor performance, utilizing the previously validated upper bound plastic limit analysis (PLA) method. In investigating the optimal load attachment of the DERA, this paper conducts a parametric study to analyze how factors such as load attachment depth, anchor aspect ratio, and load inclination affect the DERA’s load capacity. Our findings indicate that PLA can serve as a valuable analytical tool for assessing the ultimate load capacity of the DERA, particularly under inclined loading conditions.

42 ENGINEERING↗
NASA NTRS1977

The linear Fresnel lens - Solar optical analysis of tracking error effects

Real sun-tracking solar concentrators imperfectly follow the solar disk, operationally sustaining both transverse and axial misalignments. This paper describes an analysis of the solar concentration performance of a line-focusing flat-base Fresnel lens in the presence of small transverse tracking errors. Simple optics and ray-tracing techniques are used to evaluate the lens solar transmittance and focal-plane imaging characteristics. Computer-generated example data for an f/1.0 lens indicate that less than a 1% transmittance degradation occurs for transverse errors up to 2.5 deg. In this range, solar-image profiles shift laterally in the focal plane, the peak concentration ratio drops, and profile asymmetry increases with tracking error. With profile shift as the primary factor, the ninety-percent target-intercept width increases rapidly for small misalignments, e.g., almost threefold for a 1-deg error. The analytical model and computational results provide a design base for tracking and absorber systems for the linear-Fresnel-lens solar concentrator.

Cosby, R. M.↗