Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ABLATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 991 records · Page 55
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Cork-resin ablative insulation for complex surfaces and method for applying the same

A method of applying cork-resin ablative insulation material to complex curved surfaces is disclosed. The material is prepared by mixing finely divided cork with a B-stage curable thermosetting resin, forming the resulting mixture into a block, B-stage curing the resin-containing block, and slicing the block into sheets. The B-stage cured sheet is shaped to conform to the surface being insulated, and further curing is then performed. Curing of the resins only to B-stage before shaping enables application of sheet material to complex curved surfaces and avoids limitations and disadvantages presented in handling of fully cured sheet material.

Walker, H. M.↗
NASA NTRS1980

Flowfield calculations past an entry probe with ablated nose shape

The effects of ablated nose shapes on the flowfield solutions are studied, using a time-dependent finite-difference method developed by Kumar, et al. (1979). Solutions are obtained for the laminar flow of a radiating mixture of H-He in chemical equilibrium past a blunt axisymmetric body at zero angle of attack. The freestream conditions correspond to a point on a typical Jovian entry trajectory, and the initial probe shape is a 45-deg half-angle spherically blunted cone. It is found that as nose bluntness increases, the following occur: in the nose region, shock standoff distances and radiative heating rates increase substantially; surface pressure level increases, but convective heating rates decrease.

Kumar, A.↗
NASA NTRS1981

Significance of turbulence and transition location on radiative heating with ablation injection

This paper presents forebody flowfield solutions for Jupiter entry conditions where the ablation injection rate is coupled with the surface heating rate. The calculations are made with a time-dependent viscous-shock-layer analysis where the flow is assumed to be in chemical equilibrium. Both laminar and turbulent solutions are presented to describe the impact of turbulence on surface mass loss rates for flow conditions where the heating is due primarily to radiation. Results are also presented where the transition location to turbulent flow is arbitrarily varied. Results show that the radiative heating rate values based on several downstream transition locations adjust quickly to the corresponding values based on transition near the stagnation point.

Moss, J. N.↗
NASA NTRS1981

Transport properties for a mixture of the ablation products C, C2, and C3

The ablation of carbon-phenolic heat shields upon entry into the atmosphere of one of the outer planets leads to the injection of large amounts of C, C2, and C3 into the shock layer. These species must be included in the calculation of transport properties in the shock layer. The kinetic theory of gases has been used to obtain accurate results for the transport properties of monatomic carbon. The Hulburt-Hirschelder potential, the most accurate general purpose atom-atom potential for states with an attractive minimum, was used to represent such states and repulsive states were represented by fitting quantum mechanical potential energy curves with the exponential repulsive potential. These results were orientation averaged according to the peripheral force model to obtain transport collision integrals for the C-C2 and C2-C2 interaction. Results for C3 were obtained by ignoring the presence of the central carbon atom. The thermal conductivity, viscosity, and diffusion coefficients for pure C, C2, and C3, and for mixtures of these gases, were then calculated from 1000 K - 25,000 K.

Biolsi, L.↗
NASA NTRS1982

Water absorption and desorption in shuttle ablator and insulation materials

Shuttle systems ablator and insulation materials underwent water soak with subsequent water desorption in vacuum. Water accumulation in these materials after a soak for 24 hours ranged from +1.1% for orbiter tile to +161% for solid rocket booster MSA-1. After 1 minute in vacuum, water retention ranged from none in the orbiter tile to +70% for solid rocket booster cork.

Whitaker, A. F.↗
NASA NTRS1983

Stagnation-point ablation of carbonaceous flat disks. I Theory

The process of ablation is calculated for the stagnation region of a flat disk in a radiation-dominated, massive-blowing environment produced in a ballistic range filled with argon. Flow environments are determined by solving the boundary-layer equations while radiative transfer is calculated through a line-by-line spectral computation. The resulting wall heat-transfer rates are coupled with an existing material's response code to determine surface recession and char thickness. The calculation is performed for six 5-cm-diam models made of carbon-phenolic and carbon-carbon composite launched in the Track-G facility at the Arnold Engineering Development Center. Significant surface recessions are predicted to occur for these models due mostly to radiative heating.

Park, C.↗
NASA NTRS1983

Stagnation-point ablation of carbonaceous flat disks. II Experiment

Six flat-disk models made of carbon-carbon and carbon-phenolic materials were launched in an argon-filled track-range facility to test ablation characteristics in a radiation-dominated, massive-blowing environment. The shock standoff distances deduced from the shadowgraphs agree with theoretical predictions during the earlier portion of the flight, while the wall temperatures determined by the image-converter photographs agree with predictions during the later portion. The measured surface recessions exceed the calculated values by about 60 percent for carbon-phenolic and 30 percent for carbon-carbon. The discrepancies are attributed to spallation. The measured char thicknesses agree with theoretical predictions.

Park, C.↗
NASA NTRS1984

Atmospheric Profile Imprint in Firewall Ablation Coefficient

A general formula which expresses the distance along the meteoric fireball trajectory 1 as a function of t is discussed. Differential equations which include the motion and ablation of a single nonfragmenting meteor body are presented. The importance of the atmospheric density profile in the meteor formula is emphasized.

Ceplecha, Z.↗
NASA NTRS1985

Origin and development of ablator for Space Shuttle external tank

The Space Shuttle External Tank (ET) represents the largest element of the Space Shuttle transportation system. The ET is the fuel tank which contains cryogenic propellants, including liquid oxygen and liquid hydrogen. The task of providing a suitable Thermal Protection System (TPS) which is mass producible for the ET represented a challenge for the aerospace industry. The difficulties were compounded by stringent insulation and ablation requirements for the materials to maintain their integrity over a wide range of operating temperatures during prelaunch and ascent. Attention is given to the configuration of the Space Shuttle system, the configuration of the external tank, the initial ET TPS concept, TPS materials and processes concepts, design rationale, TPS materials structural considerations, material and processes development, development tests, material/process verification, and flight results.

Ronquillo, L.↗
NASA NTRS1987

Computer Simulation of Ablator Charring

Transient response of thermal-protection material to heat applied to surface calculated using CHAP III computer program. Used to analyze chemical kinetics of pyrolysis gas in detail and examine pyrolysis reactions-in-depth. Analysis includes deposition of solid products produced by chemical reactions in gas phase. Uses modeling technique that approximates wide range of ablation problems. CHAP III written in FORTRAN IV.

Stroud, C. W.↗
NASA NTRS1989

The formation flare loops by magnetic reconnection and chromospheric ablation

Noncoplanar compressible reconnection theory is combined here with simple scaling arguments for ablation and radiative cooling to predict average properties of hot and cool flare loops as a function of the coronal vector magnetic field. For a coronal field strength of 100 G, the temperature of the hot flare loops decreases from 1.2 x 10 to the 7th K to 4.0 x 10 to the 6th K as the component of the coronal magnetic field perpendicular to the plane of the loops increases from 0 percent to 86 percent of the total field. When the perpendicular component exceeds 86 percent of the total field or when the altitude of the reconnection site exceeds 10 to the 6th km, flare loops no longer occur. Shock-enhanced radiative cooling triggers the formation of cool H-alpha flare loops with predicted densities of roughly 10 to the 13th/cu cm, and a small gap of roughly 1000 km is predicted to exist between the footpoints of the cool flare loops and the inner edges of the flare ribbons.

Forbes, T. G.↗
NASA NTRS1989

Growth and patterning of laser ablated superconducting YBa2Cu3O7 films on LaAlO3 substrates

A high quality superconducting film on a substrate with a low dielectric constant is desired for passive microwave circuit applications. In addition, it is essential that the patterning process does not effect the superconducting properties of the thin films to achieve the highest circuit operating temperatures. YBa2Cu3O7 superconducting films were grown on lanthanum aluminate substrates using laser ablation with resulting maximum transition temperature (T sub c) of 90 K. The films were grown on a LaAlO3 which was at 775 C and in 170 mtorr of oxygen and slowly cooled to room temperature in 1 atm of oxygen. These films were then processed using photolithography and a negative photoresist with an etch solution of bromine and ethanol. Results are presented on the effect of the processing on T(sub c) of the film and the microwave properties of the patterned films.

Warner, J. D.↗
NASA NTRS1990

Laser ablated high T(sub c) superconducting thin YBa2Cu3O(7-x) films on substrates suitable for microwave applications

The development of high temperature superconducting YBa2Cu3O(7-x) thin films on substrates suitable for microwave applications is of great interest for evaluating their applications for space radar, communication, and sensor systems. Thin films of YBa2Cu3O(7-x) were formed on SrTiO3, ZrO2, MgO, and LaAlO3 substrates by laser ablation. The wavelength used was 248 nm from a KrF excimer laser. During deposition the films were heated to 600 C in a flowing oxygen environment, and required no post annealing. The low substrate temperature during deposition with no post annealing gave films which were smooth, which had their c-axis aligned to the substrates, and which had grains ranging from 0.2 to 0.5 microns in size. The films being c-axis aligned gave excellent surface resistance at 35 GHz which was lower than that of copper at 77 K. At present, LaAlO3 substrates with a dielectric constant of 22, appears suitable as a substrate for microwave and electronic applications. The films were characterized by resistance-temperature measurements, scanning electron microscopy, and x ray diffraction. The highest critical transition temperatures (T sub c) are above 89 K for films on SrTiO3 and LaAlO3, above 88 K for ZrO2, and above 86 K for MgO. The critical current density (J sub c) of the films on SrTiO3 is above 2 x 10(exp 6) amperes/sq cm at 77 K. The T(sub c) and J(sub c) are reported as a function of laser power, composition of the substrate, and temperature of the substrate during deposition.

Warner, J. D.↗
NASA NTRS1990

Microwave conductivity of laser ablated YBaCuO superconducting films and its relation to microstrip transmission line

The discovery of high temperature superconductor oxides has raised the possibility of a new class of millimeter and microwave devices operating at temperatures considerably higher than liquid helium temperatures. Therefore, materials properties such as conductivity, current density, and sheet resistance as a function of temperature and frequency, possible anisotropies, moisture absorption, thermal expansion, and others, have to be well characterized and understood. The millimeter wave response was studied of laser ablated YBa2Cu3O(7-x)/LaAlO3 thin films as a function of temperature and frequency. In particular, the evaluation of their microwave conductivity was emphasized, since knowledge of this parameter provides a basis for the derivation of other relevant properties of these superconducting oxides, and for using them in the fabrication of actual passive circuits. The microwave conductivity for these films was measured at frequencies from 26.5 to 40.0 GHz, in the temperature range from 20 to 300 K. The values of the conductivity are obtained from the millimeter wave power transmitted through the films, using a two fluid model.

Bhasin, K. B.↗
NASA NTRS1990

Computational equations for radiating and ablating shock layers

The computational equations governing the shock-layer flowfield over a blunt body dominated by radiation and ablation are derived. The flowfield considered is that expected around the vehicles entering the atmosphere of the planet Mars or the earth on return from Mars on a sprint-type manned mission. To determine the appropriate method of approach, the radiative transfer calculations are made first using the existing computer code RASLE (Nicolet et al., 1978), which uses the assumption of equilibrium and a coarse spectral band model for radiative transfer, and the code NONEQ which accounts for thermochemical nonequilibrium and carries out line-by-line calculation of radiation. By comparing the results, it is concluded that a thermochemical nonequilibrium model and a line-by-line spectral model must be used.

Park, Chul↗
NASA NTRS1990

Viscous-shock-layer solutions with coupled radiation and ablation injection for earth entry

Results are obtained for the forebody of a planetary exploration vehicle entering the earth's atmosphere. A viscous-shock-layer analysis is used assuming the flow to be laminar and in chemical equilibrium. Presented results include coupled radiation and ablation injection. This study further includes the effect of different transport and thermodynamic properties and radiation models. A Lewis number of 1.4 appears adequate for the radiation-dominated flows. Five velocities corresponding to different possible trajectory points at an altitude of 70 km have been further analyzed in detail. Sublimation and radiative equilibrium wall temperatures are employed for cases with and without coupled injection, respectively. For the cases analyzed here, the mass injection rates are small. However, the rates could become large if a lower altitude is used for aerobraking and/or the body size is increased. A comparison of the equilibrium results with finite-rate chemistry calculation shows the flowfield to be in chemical equilibrium.

Gupta, Roop N.↗
NASA NTRS1990

Millimeter-wave surface resistance of laser-ablated YBa2Cu3O(7-delta) superconducting films

The millimeter-wave surface resistance of YBa2Cu3O(7-delta) superconducting films was measured in a gold-plated copper host cavity at 58.6 GHz between 25 and 300 K. High-quality laser-ablated films of 1.2-micron thickness were deposited on SrTiO3 and LaGaO3 substrates. Their transition temperatures were 90.0 and 88.9 K, with a surface resistance at 70 K of 82 and 116 milliohms, respectively. These values are better than the values for the gold-plated cavity at the same temperature and frequency.

Miranda, F. A.↗
NASA NTRS1991

Deposition of high quality YBa2Cu3O(7-delta) thin films over large areas by pulsed laser ablation with substrate scanning

The paper describes thin films deposited in a system where substrates are scanned over areas up to 3.5 x 3.5 cm through the stationary plume of an ablated material defined by an aperture. These YBCO films are deposited on LaAlO3 and SrTiO3 substrates with the thickness of 90 and 160 nm. Attention is focused on the main features of the deposition system: line focusing of the laser beam on the target; an aperture defining the area of the plume; computerized stepper motor-driven X-Y stage translating the heated sampler holder behind the plume-defining aperture in programmed patterns; and substrate mounting block with uniform heating at high temperatures over large areas. It is noted that the high degree of uniformity of the properties in each film batch illustrates that the technique of pulsed laser deposition can be applied to produce large YBCO films of high quality.

Davis, M. F.↗