Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “wire”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 973 records · Page 54
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

Measurement of turbulent fluctuations in high-speed flows using hot wires and hot films

The paper examines the dynamic calibrations of the hot film and modified hot-wire probes with a view to assess their suitability for use in experiments for the measurement of turbulent fluctuations in compressible boundary-layer flows. Results are presented of tests on some sensors in both subsonic and supersonic boundary-layer flows. A simple technique is presented for determining dynamic calibration correction factors for the sensitivities involved.

Acharya, M.↗
NASA NTRS1980

Simple circuit monitors "third wire" in ac lines

Device detects interruption of ground connection in three-wire electrical equipment and shuts off ac power to prevent shock hazard. Silicon-controlled rectifiers detect floating ground, and deenergize optoelectric relays thereby breaking power connections. Circuit could be incorporated into hand tools, appliances, and other electrical equipment.

Kojima, T. T.↗
NASA NTRS1979

Efficiency of aerosol collection on wires exposed in the stratosphere

The theory of inertial impaction is briefly presented. Stratospheric aerosol research experiments were performed duplicating Wong et al. experiments. The use of the curve of inertial parameters vs particle collection efficiency, derived from Wong et al., was found to be justified. The results show that stratospheric aerosol particles of all sizes are collectible by wire impaction technique. Curves and tables are presented and used to correct particle counts for collection efficiencies less than 100%.

Lem, H. Y.↗
NASA NTRS1980

Transient corona effects on a wire over the ground

The nuclear EMP effect on VLF/trailing wire antennas is investigated in relation to new features of corona effects. Previous experimental results on transmission lines with corona under E 80 kV/cm recorded in the nanosecond time frame are analyzed. A nonlinear macroscopic model which describes a transmission line with corona is discussed. The model not only accounts for overall waveform, but also describes the sharp changes in the waveform associated with the corona onset.

Chen, K. C.↗
NASA NTRS1980

A design procedure for a tension-wire stiffened truss-column

A deployable, tension wire stiffened, truss column configuration was considered for space structure applications. An analytical procedure, developed for design of the truss column and exercised in numerical studies, was based on equivalent beam stiffness coefficients in the classical analysis for an initially imperfect beam column. Failure constraints were formulated to be used in a combined weight/strength and nonlinear mathematical programming automated design procedure to determine the minimum mass column for a particular combination of design load and length. Numerical studies gave the mass characteristics of the truss column for broad ranges of load and length. Comparisons of the truss column with a baseline tubular column used a special structural efficiency parameter for this class of columns.

Greene, W. H.↗
NASA NTRS1980

Reliability/safety analysis of a fly-by-wire system

An analysis technique has been developed to estimate the reliability of a very complex, safety-critical system by constructing a diagram of the reliability equations for the total system. This diagram has many of the characteristics of a fault-tree or success-path diagram, but is much easier to construct for complex redundant systems. The diagram provides insight into system failure characteristics and identifies the most likely failure modes. A computer program aids in the construction of the diagram and the computation of reliability. Analysis of the NASA F-8 Digital Fly-by-Wire Flight Control System is used to illustrate the technique.

Brock, L. D.↗
NASA NTRS1982

Wire-Wrap Chatter Detector

Monitoring circuit responds to changes in resistance as little as 0.1 ohm. Has been used to detect defective wire-wrap connections during thermal and vibration tests. Defect is indicated to operator by light-emitting diode and by increase in count on a two-digit display.

Fisch, G. Z.↗
NASA NTRS1982

Weld-Wire Monitor

Changes in the size or composition of weld wire being fed to an automatic welding machine are detected by an impedance-monitoring instrument. The instrument triggers an alarm if the changes would affect weld quality or cause weld failure. Device could find applications in construction of pipelines or nuclear powerplants.

Olson, R.↗
NASA NTRS1982

CADAT Printed-Wiring-Board Designer

CADAT printed-wiring-board system (PWB) designs printed-circuit and hybrid-circuit boards. It is comprised of four programs: preprocessor, placement program, organizer program, and the router. Component placement and interconnection paths are optimized.

Brinkerhoff, C. D.↗
NASA NTRS1980

Civil helicopter wire strike assessment study. Volume 2: Accident analysis briefs

A description and analysis of each of the 208 civil helicopter wire strike accidents reported to the National Transportation Safety Board (NTSB) for the ten year period 1970-1979 is given. The accident analysis briefs were based on pilot reports, FAA investigation reports, and such accident photographs as were made available. Briefs were grouped by year and, within year, by NTSB accident report number.

Tuomela, C. H.↗
NASA NTRS1981

Ground and flight test experience with a triple redundant digital fly by wire control system

A triplex digital fly by wire flight control system was developed and installed in an F-8C aircraft to provide fail operative, full authority control. Hardware and software redundancy management techniques were designed to detect and identify failures in the system. Control functions typical of those projected for future actively controlled vehicles were implemented.

Jarvis, C. R.↗
NASA NTRS1981

Silicon Ingot Casting - Heat Exchanger Method (HEM). Multi-Wire Slicing - Fixed Abrasive Slicing Technique (Fast). Phase 4 Silicon Sheet Growth Development for the Large Area Sheet Task of the Low-Cost Solar Array Project

The crystallinity of large HEM silicon ingots as a function of heat flow conditions is investigated. A balanced heat flow at the bottom of the ingot restricts spurious nucleation to the edge of the melted-back seed in contact with the crucible. Homogeneous resistivity distribution over all the ingot has been achieved. The positioning of diamonds electroplated on wirepacks used to slice silicon crystals is considered. The electroplating of diamonds on only the cutting edge is described and the improved slicing performance of these wires evaluated. An economic analysis of value added costs of HEM ingot casting and band saw sectioning indicates the projected add on cost of HEM is well below the 1986 allocation.

Schmid, F.↗
NASA NTRS1980

Transmission line model of the interaction of a long metal wire with the ionosphere

An equivalent electric circuit model is used to study the electrodynamic interactions of long orbiting metallic tethers with the ionospheric plasma and, in particular, to derive current and potential profiles along bare metallic tethers. In contrast with other models, this approach is dynamic, enabling both the transient behavior of the wire and its final equilibrium state to be derived. A comparison with the results of other models indicates the advantage of the present approach, especially in those cases where the internal resistance of the tether plays a major role in determining the current and potential distributions.

Arnold, D. A.↗
NASA NTRS1981

Influence of velocity gradients on measurements of velocity and streamwise vorticity with hot-wire X-array probes

An analysis and measurement of the effects of the streamwise velocity gradients partial derivative of U with respect to y and partial derivative of U with respect to z, on the velocity components, U, v, and w, and the streamwise vorticity component, omega sub x measured in turbulent flow with a pair of orthogonal hot-wire X arrays, is presented. It is shown that these gradients, which can have the same order of magnitude instantaneously as the mean shear stress at the wall, cause extremely large errors in the measured instantaneous cross-stream velocity and streamwise vorticity components.

Vukoslavcevic, P.↗
NASA NTRS1981

Reliability analysis of the F-8 digital fly-by-wire system

The F-8 Digital Fly-by-Wire (DFBW) flight test program intended to provide the technology for advanced control systems, giving aircraft enhanced performance and operational capability is addressed. A detailed analysis of the experimental system was performed to estimated the probabilities of two significant safety critical events: (1) loss of primary flight control function, causing reversion to the analog bypass system; and (2) loss of the aircraft due to failure of the electronic flight control system. The analysis covers appraisal of risks due to random equipment failure, generic faults in design of the system or its software, and induced failure due to external events. A unique diagrammatic technique was developed which details the combinatorial reliability equations for the entire system, promotes understanding of system failure characteristics, and identifies the most likely failure modes. The technique provides a systematic method of applying basic probability equations and is augmented by a computer program written in a modular fashion that duplicates the structure of these equations.

Brock, L. D.↗
NASA NTRS1981

XV-15 Tilt Rotor fly-by-wire collective control demonstrator development specifications

A fly by wire system in the collective control system for XV-15 Tilt Rotor Research Aircraft was evaluated. The collective control system was selected because it requires a system tracking accuracy between right and left rotors of approximately 0.1%. The performance characteristics of the collectors axel provide typical axis control response data. The demonstrator is bread boarded as a dual system instead of the triplex system.

Meuleners, R. J.↗