Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “waters”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 973 records · Page 54
All sourcesNASA NTRSDOE OSTI
DOE OSTI2018

Determination of the Ability to Measure Traces of Water in Dehydrated Residues of Waste Water by IR Diffuse Reflectance Spectra

Rapid measurement of the moisture content of dehydrated residues is a critical problem, the solution of which will increase the efficiency of treatment facilities and optimize the process of applying flocculants. The ability to determine the moisture content of dehydrated residues using a meter operating on the IR reflectance principle was confirmed experimentally. The most suitable interference filters were selected based on an analysis of the obtained diffuse reflectance spectrum of the dehydrated residue in the range 1.0–2.7 μm. Calibration curves were constructed and compared for each filter set. A measuring filter with a transmittance maximum at 1.19 μm and a reference filter with a maximum at 1.3 μm gave the best agreement with the laboratory measurements.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2015

The dissociative chemisorption of water on Ni(111): Mode- and bond-selective chemistry on metal surfaces

A fully quantum approach based on an expansion in vibrationally adiabatic eigenstates is used to explore the dissociative chemisorption of H{sub 2}O, HOD, and D{sub 2}O on Ni(111). For this late barrier system, excitation of both the bending and stretching modes significantly enhances dissociative sticking. The vibrational efficacies vary somewhat from mode-to-mode but are all relatively close to one, in contrast to methane dissociation, where the behavior is less statistical. Similar to methane dissociation, the motion of lattice atoms near the dissociating molecule can significantly modify the height of the barrier to dissociation, leading to a strong variation in dissociative sticking with substrate temperature. Given a rescaling of the barrier height, our results are in reasonable agreement with measurements of the dissociative sticking of D{sub 2}O on Ni(111), for both laser-excited molecules with one or two quanta of excitation in the antisymmetric stretch and in the absence of laser excitation. Even without laser excitation, the beam contains vibrationally excited molecules populated at the experimental source temperature, and these make significant contributions to the sticking probability. At high collision energies, above the adiabatic barrier heights, our results correlate with these barrier heights and mode softening effects. At lower energies, dissociative sticking occurs primarily via vibrationally nonadiabatic pathways. We find a preference for O–H over O–D bond cleavage for ground state HOD molecules at all but the highest collision energies, and excitation of the O–H stretch gives close to 100% O–H selectivity at lower energies. Excitation of the O–D stretch gives a lower O–D cleavage selectivity, as the interaction with the surface leads to energy transfer from the O–D stretch into the O–H bond, when mode softening makes these vibrations nearly degenerate.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2016

Vapor deposition of molybdenum oxide using bis(ethylbenzene) molybdenum and water

Three molybdenum precursors—bis(acetylacetonate) dioxomolybdenum, molybdenum isopropoxide, and bis(ethylbenzene) molybdenum—were tested for molybdenum oxide vapor deposition. Quartz crystal microbalance studies were performed to monitor growth. Molybdenum isopropoxide and bis(ethylbenzene) molybdenum achieved linear growth rates 0.01 and 0.08 Å/cycle, respectively, using atomic layer deposition techniques. Negligible MoO{sub x} growth was observed on alumina powder using molybdenum isopropoxide, as determined by inductively coupled plasma optical emission spectroscopy. Bis(ethylbenzene) molybdenum achieved loadings of 0.5, 1.1, and 1.9 Mo/nm{sup 2} on alumina powder after one, two, and five cycles, respectively, using atomic layer deposition techniques. The growth window for bis(ethylbenzene) molybdenum is 135–150 °C. An alternative pulsing strategy was also developed for bis(ethylbenzene) molybdenum that results in higher growth rates in less time compared to atomic layer deposition techniques. The outlined process serves as a methodology for depositing molybdenum oxide for catalytic applications. All as-deposited materials undergo further calcination prior to characterization and testing.

36 MATERIALS SCIENCE↗
DOE OSTI2015

X-ray-driven reaction front dynamics at calcite-water interfaces

The interface between minerals and aqueous solutions hosts globally important biogeochemical processes such as the growth and dissolution of carbonate minerals. Understanding such processes requires spatially and temporally resolved observations and experimental controls that precisely manipulate the interfacial thermodynamic state. Using the intense radiation fields of a focused synchrotron x-ray beam, we drove dissolution at the calcite/water interface and simultaneously probed the dynamics of the propagating reaction fronts using surface x-ray microscopy. Evolving surface structures were controlled by the time-dependent solution composition, as characterized by a kinetic reaction model. At extreme disequilibria, we observed the onset of reaction front instabilities with velocities of > 30 nanometers per second. These instabilities serve as a signature of transport-limited dissolution of calcite under extreme disequilibrium.

calcite-water interface↗