SEARCH · Engineering Papers

Results for “transference number”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 973 records · Page 54

All sources NASA NTRS DOE OSTI

DOE OSTI2026

Numerical Simulation of a Natural Convection–Driven Air-Cooled Reactor Cavity Cooling System Experiment

Ensuring the efficient removal of decay heat from the reactor vessel is essential for the safety of advanced reactor technologies. Several Generation-IV concepts incorporate variations in the reactor vessel cooling systems to achieve this objective. High-temperature gas-cooled reactors utilize a reactor cavity cooling system (RCCS), a passive ex-vessel system designed to operate without active components or external power during accident conditions. The RCCS removes decay heat primarily through radiative and convective heat transfer mechanisms. Here, this study presents a comprehensive validation of a computational fluid dynamics Reynolds-averaged Navier-Stokes model for the University of Wisconsin-Madison air-cooled RCCS facility. Validation was conducted for both high- and low-power natural convection cases under a uniform heating profile. Near-wall resolution was found to be critical for accurately modeling natural convection in the RCCS; employing an all-𝑦 + wall treatment resulted in wall temperature discrepancies exceeding 50 °⁢𝐶 compared to a wall-resolved mesh. Thermal-hydraulic behaviors under natural and forced convection conditions were compared within the heated cavity and RCCS. A turbulence model sensitivity analysis indicated that low-Reynolds number k-ɛ, k-ω shear stress transport (SST), and Reynolds stress transport models produce similar wall temperature predictions. A buoyancy modeling sensitivity study revealed that the Boussinesq approximation significantly underpredicted thermal-hydraulic behavior in the RCCS. Based on these findings, modeling recommendations are provided. The validated data set along with identified sensitivities refine the modeling of natural convection in the RCCS. The information produced by this study supports RCCS design, optimization, and safety evaluations, enabling the calibration and verification of reduced-order thermal-hydraulic models.

22 - GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2023

IDAES-PSE 2.1.0 Release

The Institute for the Design of Advanced Energy Systems (IDAES) Integrated Platform is a versatile computational environment offering extensive process systems engineering (PSE) capabilities for optimizing the design and operation of complex, interacting technologies and systems. IDAES enables users to efficiently search vast, complex design spaces to discover the lowest cost, most environmentally sustainable solutions while supporting the full process modeling lifecycle, from conceptual design to dynamic optimization and control. The extensible, open platform empowers users to create models of novel processes and rapidly develop custom analyses, workflows, and end-user applications. IDAES-PSE 2.1.0 Release Highlights New IDAES Examples Repository Starting with this release, the IDAES examples are developed in the new IDAES/examples repository. Along with many content and usability improvements, the most significant changes are: To install the examples, after installing IDAES, run pip install idaes-examples The idaes get-examples command, previously used for this, has been removed The HTML version is now available at https://idaes-examples.readthedocs.io The previous URL, https://idaes.github.io/examples-pse, will not be updated and may be removed at some point in the future For more details, refer to the resources available at IDAES/examples. Removal of Non-Functional Apps A review of the code in the idaes/apps and idaes/models_extra folders was undertaken, and a number of tools were identified as being outdated or non-functional and no longer supported by their development teams. Due to this, the following tools have been removed: idaes/apps/alamopy_depr (note that the new ALAMOpy interface remains avaialble in idaes/core/surrogates) idaes/apps/helmet idaes/apps/ripe idaes/apps/roundingRegression idaes/models_extra/carbon_capture Pyomo 6.6 This version of IDAES is the first requiring Pyomo 6.6. This version of Pyomo contains multiple internal improvements and refactorings. While for the majority of cases this should have positive or no impact on solvability of IDAES models, we are aware of a small number of models that have been affected as a result of these changes. For more information, refer to the Pyomo 6.6.1 release notes. Other highlights Model Initialization A prototype API for a new approach to initializing IDAES models is now available which makes available some new techniques for initializing models. This is documented in the Initializing Models Reference Guide Modular Properties Framework Support for some transport properties Helmholtz Equation of State properties Better error checking for case where unit models are set to include phase equilibrium but the property package is set to support only a single phase Multi-Stream Contactor model: a new base model for systems involving contacting of two or more streams with mass transfer. This model is intended to be used as the foundation for models such as membrane separators, solvent extraction and other similar processes. This is documented in the Multi-Stream Contactor Reference Guide idaes/models_extra/power_generation report() methods for unit models using Helmholtz equation of state General Code Maintenance Streamlining of dependencies and creation of new optional dependency groupings to support non-core tools General linting of codebase to ensure compliance with most pylint checks Spell checking of all code and doc strings Removal of backward compatibility code for Python 2

IDAES↗

DOE OSTI2020

Wireless Instrumented RB Experiment Preliminary Design and Analysis

The ability to deploy new nuclear fuels for current or future reactor concepts requires carefully designed experiments to generate data to support fuel qualification. Ideally these experiments would include state of-the-art sensing to maximize the amount of in situ data that can be collected during operation. Furthermore, advanced reactor systems can take advantage of integrated in-core sensing technologies to maximize fuel utilization, reduce unnecessary conservativism in design margins, and improve operator’s understanding of limiting peaking factors. Before any novel sensing technologies can be readily adopted for nuclear applications, they must first demonstrate acceptable performance in test reactors. This report summarizes the preliminary design and analysis of the most highly instrumented irradiation experiment ever performed in the removable beryllium (RB) positions of the High Flux Isotope Reactor (HFIR) at Oak Ridge National Laboratory (ORNL). The Wireless Instrumented RB Experiment 2021 (WIRE-21) will test a wide range of sensors including wireless sensors being developed by Westinghouse Electric Company (WEC) that could provide in situ measurements of peak fuel temperatures and fuel rod pressurization due to fission gas release. The ability to wirelessly transmit a signal through the fuel rod’s cladding is critical to improving fuel monitoring capabilities without requiring signal penetrations through the cladding pressure boundary, which would significantly impact fuel fabrication, handling, and operation. Other sensors that will be tested in WIRE-21 include an array of thermocouples, self-powered neutron detectors (SPNDs), and spatially distributed fiber-optic temperature sensors. More generally, WIRE-21 will establish a flexible irradiation vehicle design to allow accelerated, economical testing of advanced sensor technologies while leveraging the extremely high neutron flux that is available in HFIR. This report summarizes the mechanical design for WIRE-21, the experimental test matrix, initial neutronic and thermal design analyses, and the active monitoring and control system enhancements necessary to support testing of advanced sensor technologies. The containment for WIRE-21 is similar to previous RB irradiation vehicles but includes a few modifications, most notably the use of integrated compression seals to pass a larger number of sensor leads through the experiment’s pressure boundary. In addition to the sensor leads, inert gas lines are passed into the experiment to enable active temperature control and the ability to pneumatically actuate a bellows-driven pressure sensor. WIRE-21 is targeting temperatures (300–350°C) and neutron fluence levels (~10 22 n/cm 2 ) relevant to light water reactors (LWRs), but the flexible design of the experiment vehicle allows much higher operating temperatures (>1,100°C). Neutronic calculations determine the neutron flux conditions as well as the nuclear heating within the experiments. These results are used as inputs to detailed thermal finite element calculations, which are required to evaluate the complex, three-dimensional heat transfer that occurs within WEC’s wireless sensor enclosures. Initial results show that the temperatures of the sensors’ enclosures and the metal bellows can be operated near the temperature range of LWR coolants and cladding while simultaneously increasing the temperature of a surrogate fuel material to values in the range of 800–1200°C to simulate centerline fuel temperatures during LWR operation.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2020

Remote Radiation Sensing Using Aerial and Ground Platforms

Remote sensing of ionizing radiation has a significant role in waste management, nuclear material management and nonproliferation, and radiation safety. Robotic platforms can surpass the number of tasks that are achieved by humans. With this technique, the operator's radiation exposure can be decreased. Remote sensing allows for the evaluation and monitoring of radiological contamination. Gamma-ray and neutron sensors were integrated onto the robotic platforms. This approach allows for the radiation sensor data to be dynamically tracked and mapped thus enabling further analysis of the radiation flux in temporal and spatial domains. The goal is to complete scheduled tasks while the robot is being irradiated. To achieve this, electronic components must be shielded and radiation hardened. CZT Detector: Cadmium Zinc Telluride (CZT) detector technology has been a promising solution for gamma-ray and x-ray measurements. Detector data is transferred to the Odroid minicomputer that controls and powers the module via the USB. Robot Operating System (ROS) was utilized for data acquisition and data fusion. The Mariscotti method was employed for the spectrum analysis. A function was programmed in ROS for the automatic identification of photopeaks. CLYC Detector: A Cs{sub 2}LiYCl{sub 6}:Ce{sup 3+} (CLYC) detector was used for simultaneous medium-resolution gamma-ray measurements and neutron counting. A 2.54 cm diameter photomultiplier tube (PMT) was equipped with a high voltage supply and a miniature digitizer. Gamma-ray excitation: fast core-to-valence luminescence (CVL) with 1 ns decay constant, and prompt Ce{sup 3+} emission with 50 ns decay constant. Neutron excitation: slow cerium self-trapped excitation (Ce{sup 3+} STE), 1000 ns decay constant. Radiation Source Localization: Maximum Likelihood Estimation (MLE) and gradient-based methods were used to locate the position of a radiation source based on measured radiation intensities. Multi-Particle Transport Code FLUKA: Estimation of radiation damage of the electronic components is important in order to optimize the robot's operational time while it is irradiated. Displacement per atom (DPA) represents the radiation damage in materials exposed to the ionizing radiation. Various shielding layers of different thickness t were analyzed (< 5% statistical error). The model of the controller of the UAS was designed in FLUKA. Conclusion: CZT and CLYC detectors were integrated onto the robotic platforms. Radiation source localization and contour mapping using robotic platforms were studied. Functions for data analysis and fusion were developed in ROS. FLUKA code was utilized to analyze DPA values. Layers of low-density and high-density materials were used to shield the UAS electronics.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2020

Ultrafast Spin Crossover in a Room-Temperature Ferrimagnet: Element-Specific Spin Dynamics in Photoexcited Cobalt Ferrite

Transition metal complexes capable of photoinduced spin crossover have been greatly investigated because of their potential to enable ultrafast optical control of information processing. Yet, any real application of photoswitchable molecules requires that spin crossover be paired with additional functionality such as long-range magnetic order. Important advances combining these functions are notably reported for a number of bimetallic Prussian Blue analogues; however, to date, PBA-based magnetic photoswitches can only operate below 150 K due to loss of magnetic order. In contrast, cobalt ferrite is a ferrimagnetic semiconductor with a Curie temperature of 790 K and extremely favorable magnetic properties by comparison to state-of-the-art PBAs. The mixed valence electronic structure of cobalt ferrite is reminiscent of cobalt–iron PBA, which is a well-known photoswitch. To investigate the potential for photoswitching in this material, we employ transient XUV spectroscopy to probe charge and spin dynamics with element-specific resolution on the femtosecond time scale. Results show that 400 nm light excites a metal-to-metal charge transfer transition, which drives the crossover of high-spin Co 2+ to low-spin Co 3+ with a time constant of 405 ± 29 fs and an internal quantum efficiency of unity. This result establishes the existence of efficient photoswitching in a new class of robust ferrimagnetic spinel ferrites.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2024

Vortex bursting and associated twist dynamics on helical vortex tubes and vortex rings

The interaction of opposite-signed twist waves on vortex tubes can lead to vortex bursting, a process where the core expands into a double ring-like structure with strong swirling flows. Previous works have studied vortex bursting on rectilinear vortices by axially perturbing the initial core size to generate the twist waves, and observed largely axisymmetric bursting dynamics. In this work, we numerically study bursting on vortical structures with curved centrelines, analysing the interaction between the centreline dynamics, twist wave generation and propagation, and vortex bursting. We focus on axially perturbed helical vortex tubes with small radius-to-pitch ratios up to$0.0625$, as well as vortex rings with a large radius-to-core size ratio$10$, both at a circulation-based Reynolds number$5000$. The results show that though the initial twist wave propagation speeds are relatively unaffected by the curvature and torsion of the centreline, the bursting process is altered significantly compared with rectilinear vortices. The self-induced rotation of the centreline of the helical tube induces a non-axisymmetric distortion of the bursting structure, which rapidly breaks up the vortex core into small-scale helical structures. A similar destabilization of the bursting structure also occurs on vortex rings. The enstrophy increase and accelerated energy decay associated with bursting are predominantly determined by the twist wave strength, rather than the curvature and torsion of the centreline. Combined, our findings imply that bursting could play an important role in transferring and dissipating energy of vortical structures in wakes, and turbulent flows in general.

Mechanics↗

DOE OSTI2023

Description of the multinucleon transfer mechanism for Ca 48 + Pu 244 and Kr 86 + Pt 198 reactions in a quantal transport approach

Multinucleon transfer (MNT) reactions involving heavy projectile and target combinations stand as a promising method for synthesizing new neutron-rich exotic nuclei, which may not be possible using hot or cold fusion reactions or fragmentation. Exploring the mechanisms behind MNT reactions is essential and it requires a comprehensive theoretical framework that can explain the physical observables in these reactions. This work aims to show that the quantal diffusion approach based on the stochastic mean-field (SMF) theory is capable of explaining the reaction dynamics observed in MNT reactions. Primary product mass distributions in 48 Ca + 244 Pu reaction at E c.m. = 203.2 MeV and 86 Kr + 198 Pt reaction at E c.m. = 324.2 MeV are calculated and compared with the available experimental data. In this work, we utilize the time-dependent Hartree-Fock (TDHF) calculations to analyze the mean-field reaction dynamics computationally in the reactions 48 Ca + 244 Pu and 86 Kr + 198 Pt for a broad range of initial angular momenta. Quantal transport description based on the SMF approach is used to calculate quantal diffusion coefficients and mass variances in 48 Ca + 244 Pu and 86 Kr + 198 Pt systems. The primary products arising from quasifission reactions are described by joint probability distribution in the SMF approach and those arising from fusion-fission are estimated by using the statistical deexcitation code gemini + +. Mean values of charge and mass numbers, scattering angles of the primary reaction products, and the total kinetic energies after the collision are calculated within the TDHF framework for a broad range of initial angular momenta. Throughout all the collisions, drift toward the mass symmetry and large mass dispersion associated with this drift are observed. Here, the calculated primary fragment and mass distributions using the SMF approach successfully explain experimental observations for the 48 Ca + 244 Pu and 86 Kr + 198 Pt systems. The primary mass distributions, mean values of binary products, and mass dispersions are determined and results are compared with the available experimental data. The observed agreement between the experimental data and SMF results highlights the effectiveness of the quantal diffusion mechanism based on the SMF approach, which does not include any adjustable parameters other than standard parameters of Skyrme energy density functional.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

DOE OSTI2024

Robust surfactant-assisted one-pot sample preparation for label-free single-cell and nanoscale proteomics

With advanced mass spectrometry (MS)-based proteomics, genome-scale proteome coverage can be achieved from bulk cells. However, such bulk measurement obscures cell to cell heterogeneity, precluding proteome profiling of single cells and small numbers of cells of interest. To address this issue, in recent 5 years there are a surge of small sample preparation methods developed for robust effective collection and processing of single cells and small numbers of cells for in-depth MS-based proteome profiling. Based on their broad accessibility, they can be categorized into two types: specific device- and standard PCR tube- or multi-well plate-based methods. Herein we describe the detailed protocol of our recently developed, easily adoptable, Surfactant-assisted One-Pot (SOP) sample preparation coupled with MS method termed SOP-MS for label-free single-cell and nanoscale proteomics. SOP-MS capitalizes on the combination of a MS-compatible surfactant, DDM (n-Dodecyl-ß-D-maltoside), and standard low-bind PCR tube or multi-well plate for ‘all-in-one’ one-pot sample preparation without sample transfer. With its robust and convenient features, SOP-MS can be readily implemented in any MS laboratory for single-cell and nanoscale proteomics. With further improvements in MS detection sensitivity and sample throughput, we believe that SOP-MS could open an avenue for single-cell proteomics with broad applicability in the biological and biomedical research.

Single-cell proteomics, nanoscale proteomics, SOP-↗

DOE OSTI2022

Near-cancellation of up- and down-gradient momentum transport in forced magnetized shear-flow turbulence

Visco-resistive magnetohydrodynamic turbulence, driven by a two-dimensional unstable shear layer that is maintained by an imposed body force, is examined by decomposing it into dissipationless linear eigenmodes of the initial profiles. The down-gradient momentum flux, as expected, originates from the large-scale instability. However, continual up-gradient momentum transport by large-scale linearly stable but nonlinearly excited eigenmodes is identified and found to nearly cancel the down-gradient transport by unstable modes. The stable modes effectuate this by depleting the large-scale turbulent fluctuations via energy transfer to the mean flow. This establishes a physical mechanism underlying the long-known observation that coherent vortices formed from nonlinear saturation of the instability reduce turbulent transport and fluctuations, as such vortices are composed of both the stable and unstable modes, which are nearly equal in their amplitudes. The impact of magnetic fields on the nonlinearly excited stable modes is then quantified. Furthermore, even when imposing a strong magnetic field that almost completely suppresses the instability, the up-gradient transport by the stable modes is at least two-thirds of the down-gradient transport by the unstable modes, whereas for weaker fields, this fraction reaches up to 98%. These effects are persistent with variations in magnetic Prandtl number and forcing strength. Finally, continuum modes are shown to be energetically less important, but essential for capturing the magnetic fluctuations and Maxwell stress. A simple analytical scaling law is derived for their saturated turbulent amplitudes. It predicts the falloff rate as the inverse of the Fourier wavenumber, a property which is confirmed in numerical simulations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2021

Numerical study to predict the effect of surface roughness on the thermal and hydraulic performance of additively manufactured heat exchangers

Heat exchangers are used in many industries to transfer thermal energy between two or more objects with an associated thermal and hydraulic performance indicated by thermal effectiveness and pressure drop respectively. Many investigations have aimed to enhance the thermal effectiveness of heat exchangers by introducing turbulent flow inducers that increase the heat transfer rate at the expense of increasing pressure drop. Flow inducers like surface roughness can be controlled with advanced manufacturing methods like additive manufacturing for heat exchanger production. Selecting and manufacturing an optimal surface roughness for heat exchangers requires a more comprehensive approach that accounts for the surface roughness effect on the thermal and hydraulic performance of a sample. Since fabricating samples with additive manufacturing to a desired surface roughness can be an extensive experimental process, this study will fundamentally investigate the effect of surface roughness on the thermal and velocity boundary layers for various surface roughness profiles with physics-based computational modeling. To accurately model the surface roughness effect on thermohydraulic performance, correlations like roughness ratio, friction factor, and Nusselt number are investigated. This study expects to indicate correlations for different flow regimes which can successfully predict the effect of surface roughness on thermohydraulic performance. Results generated from modeling surface roughness effect with unique correlations are then compared to experimental data obtained from literature for validation. The results of this study will provide insight to understand the thermal fluid physics associated with surface roughness and design guidelines for heat exchangers produced with additive manufacturing.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Flow structures of the cross-flow over a five-layer helically coiled steam generator geometry

The helically-coiled heat exchanger (HCSG) offers advantages over straight tubes such as compactness in geometry, increased heat transfer coefficients, and capability to absorb thermal expansion. In this study, the time-resolved velocity field data of shell-side crossflow over a five-layer helically coiled steam generator geometry was obtained using Particle Image Velocimetry (PIV) between adjacent rods in four regions with up to 5000 frames per second (5 kHz) at approximately Re u = 3600. The slant rod bundle created different flow patterns in different regions. Proper Orthogonal Decomposition (POD) revealed high-energy-mode flow structures. Due to the confined flow channel geometry, the large flow structures were not advected resulting in no strong POD mode paring. Continuous Wavelet Transform (CWT) visualized the characteristics of flow fluctuation in time and frequency domain simultaneously, which ranged in Strouhal number, S u , between 0.03 and 1.17. In the wake regions of the rods, flows changed in both pattern and magnitude over time. Once a pattern formed, it continued for relatively shorter than straight tube arrays, before changing the pattern again. The histograms of the POD time coefficients presented this multimodal flow characteristics. The current study focuses more on whole flow field analyses in the selected regions rather than local point-wise analyses. Finally, this study revealed that various Strouhal numbers can exist in the helically coiled heat exchanger geometry, which was not observed in straight tube arrays. In particular, Strouhal numbers smaller than 0.1 do not seem to be caused by vortex shedding but seem to be the result of the combination of complex geometry and possible multimodal trends. Based on the current observation, further works would involve intensive instantaneous point-wise analyses on the interactions between important locations such as separation points, stagnation points, shear layers, etc.

42 ENGINEERING↗

DOE OSTI2022

Determination of Sodium Abundance Ratio from Low-resolution Stellar Spectra and Its Applications

We present a method to determine sodium abundance ratios ([Na/Fe]) using the Na i D doublet lines in low-resolution (R ~ 2000) stellar spectra. As stellar Na i D lines are blended with those produced by the interstellar medium, we developed a technique for removing the interstellar Na I D lines using the relationship between extinction, which is proportional to E(B – V), and the equivalent width of the interstellar Na i D absorption lines. When measuring [Na/Fe], we also considered corrections for nonlocal thermodynamic equilibrium (NLTE) effects. Comparisons with data from high-resolution spectroscopic surveys suggest that the expected precision of [Na/Fe] from low-resolution spectra is better than 0.3 dex for stars with [Fe/H] > –3.0. We also present a simple application employing the estimated [Na/Fe] values for a large number of stellar spectra from the Sloan Digital Sky Survey (SDSS). After classifying the SDSS stars into Na-normal, Na-high, and Na-extreme, we explore their relation to stars in Galactic globular clusters (GCs). We find that while the Na-high SDSS stars exhibit a similar metallicity distribution function (MDF) to that of the GCs, indicating that the majority of such stars may have originated from GC debris, the MDF of the Na-normal SDSS stars follows that of typical disk and halo stars. As there is a high fraction of carbon-enhanced metal-poor stars among the Na-extreme stars, they may have a non-GC origin, perhaps due to mass-transfer events from evolved binary companions.

79 ASTRONOMY AND ASTROPHYSICS↗

DOE OSTI2022

Scaling CFB risers: Maintaining microstructure dynamics

Over the years there have been numerous approaches to develop a scaleup methodology for circulating fluidized beds. Many of these past approaches have relied on macroscopic definitions of similitude to define dimensionless groups such as Reynolds number, Froude number, density ratios, and dimensional ratios involving different length scales. These approaches have demonstrated various levels of success, but often fail when used outside the bounds of experimental datasets. The issue with these methods is that they rely on macroscopic similitude with the hopes that those conditions would provide microscopic similitude as it does in single phase systems where the Buckingham Pi techniques have given reasonable success. Two of the main reasons for failure are 1) changing fluidization regimes and 2) changing material properties that result in the material falling into a different Geldart group. Both are certain to change the microstructure (local instantaneous volume solids fraction) and changes to the microstructure affect the interphase transport properties of the reactor system, namely the mass transfer and heat transfer. Here, this work presents a new approach towards scaling based upon maintaining similitude at the microscale. It reviews a novel dimensionless flow regime map developed from analysis of the deterministic chaos parameters and higher order moments to ensure microstructure similitude. The work then examines four cases from the literature to assess the scaling approach used: (1) same particle-different scale risers for Geldart Group B particles, (2) Glicksman scaling of atmospheric circulating fluidized bed combustor, (3) same particle-different scale risers for Geldart Group A particles and (4) Glicksman scaling for pressurized gasification. General findings are that none of the scaling approaches produced directly applicable microstructure similar behavior based upon the chaotic and higher moment analysis. The positive take away is that the approach can define scale conditions that will provide similar microstructure that can be us to predict transport behavior.

42 ENGINEERING↗

DOE OSTI2023

Intrinsic thermal conductivity of ZrC from low to ultrahigh temperatures: A critical revisit

Current phonon transport theory based on ground-state calculations has been successful in predicting thermal conductivity at room and medium temperatures but may misrepresent behavior at high temperatures. Here, in this work, we predict the thermal conductivity (κ) of ZrC including electronic and phonon contributions from 300 to 3500 K, by including high-order phonon scattering; lattice expansion; temperature-dependent (TD) second-, third-, and fourth-order force constants (2FC, 3FC, and 4FC); and interband phonon conduction by using first principles. For the phonon transport, we find that four-phonon scattering (4ph) significantly reduces the phonon thermal conductivity (κ ph ), by as much as ~75% at 3500 K. After including 4ph scattering and all other factors, κ ph shows a ~T –1.5 rather than ~T –1 dependence. TD 2FC decreases three-phonon scattering rates but increases 4ph rates by decreasing and increasing the scattering phase spaces, respectively. For 4ph phase space, the TD 2FC flattens phonon bands, and allows more redistribution-4ph processes (1 + 2 → 3 + 4) to happen. The combination effect of TD 2FC and TD 4FC reduces 4ph rates of acoustic modes but increases those of optical modes. The TD 3FC and 4FC decrease the phonon scattering cross section and increase the κ ph significantly (by 52% at 3500 K). The contribution from interband (Wigner) phonon conduction is small, even at ultrahigh temperatures. For electronic thermal transport, we find that it is sensitive to and can be changed by 20% by the TD lattice constants. The Lorenz number varies from 1.6 to 3.3 × 10 –8 WΩK –2 at different temperatures. The theoretical prediction in the literature overpredicts κph (e.g., ~28%) and underpredicts the κ el (e.g., ~38%), resulting in an overall underprediction of κ (~26% at 1500 K). The impacts of grain size and defects are found to be strong, leading to the lower observed thermal conductivity in experiments.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

DOE OSTI2021

Systematic Influence of Electronic Modification of Ligands on the Catalytic Rate of Water Oxidation by a Single-Site Ru-Based Catalyst

Catalytic water oxidation is an important process for the development of clean energy solutions and energy storage. Despite the significant number of reports on active catalysts, systematic control of the catalytic activity remains elusive. In this study, descriptors are explored that can be correlated with catalytic activity. [Ru(tpy)(pic) 2 (H 2 O)](NO 3 ) 2 and [Ru(EtO-tpy)(pic) 2 (H 2 O)](NO 3 ) 2 (where tpy=2,2': 6',2“-terpyridine, EtO-tpy=4'-(ethoxy)-2,':6',2”-terpyridine, pic=4-picoline) are synthesized and characterized by NMR, UV/Vis, EPR, resonance Raman, and X-ray absorption spectroscopy, and electrochemical analysis. Addition of the ethoxy group increases the catalytic activity in chemically driven and photocatalytic water oxidation. Thus, the effect of the electron-donating group known for the [Ru(tpy)(bpy)(H 2 O)] 2+ family is transferable to architectures with a tpy ligand trans to the Ru-oxo unit. Under catalytic conditions, [Ru(EtO-tpy)(pic) 2 (H 2 O)](NO 3 ) 2 displays new spectroscopic signals tentatively assigned to a peroxo intermediate. In conclusion, reaction pathways were analyzed by using DFT calculations. [Ru(EtO-tpy)(pic) 2 (H 2 O)](NO 3 ) 2 is found to be one of the most active catalysts functioning by a water nucleophilic attack mechanism.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2025

Accelerating high-order continuum kinetic plasma simulations using multiple GPUs

Kinetic plasma simulations solve the Vlasov-Poisson or Vlasov-Maxwell equations to evolve scalar-variable distribution functions in position-velocity phase space and vector-variable electromagnetic fields in configuration space. The immense computational cost of evolving high-dimensional variables, and their large number of degrees of freedom, often limits the utility of continuum kinetic simulations and presents a challenge when it comes to accurately simulating real-world physical phenomena. To address this challenge, we present techniques that accelerate and minimize the computational work required for a scalable Vlasov-Poisson solver. We show theoretical hardware compute and communication bounds for solving a fourth-order finite-volume Vlasov-Poisson system. These bounds are then used to inform and evaluate the design of performance portable algorithms for a multiple graphics processing unit (GPU) accelerated version of the Vlasov-Poisson solver VCK-CPU [1]. We demonstrate that the multi-GPU Vlasov solver implementation, VCK-GPU, simultaneously minimizes required inter-process data transfer while also being bounded by the machine network performance limits. This results in an overall strong scaling speedup per timestep of up to 40x in three-dimensional phase space (one position, two velocity coordinates) and 54x in four dimensional phase space (two position, two velocity coordinates) and a 341x increase in simulation throughput of the GPU accelerated code over the existing CPU code. The GPU code is also able to weak scale up to 256 compute nodes and 1024 GPUs. In conclusion, we demonstrate that the improved compute performance enables exploring configurations which were previously computationally infeasible, including resolving fine-scale distribution function filamentation and multi-species dynamics with realistic electron-proton mass ratios.

Continuum kinetics↗

DOE OSTI2024

CH 3 Radical Generation in Microplasmas for Up-Conversion of Methane

The conversion of methane, CH 4 , into higher value chemicals using low temperature plasmas is challenged by both improving efficiency and selectivity. One path towards selectivity is capturing plasma produced methyl radicals, CH 3 , in a solvent for aqueous processing. Due to the rapid reactions of methyl radicals in the gas phase, the transport distance from production of the CH 3 to its solvation should be short, which then motivates the use of microplasmas. The generation of CH 3 in Ar/CH 4 /H 2 O plasmas produced in nanosecond pulsed dielectric barrier discharge microplasmas is discussed using results from a computational investigation. The microplasma is sustained in the channel of a microfluidic chip in which the solvent flows along one wall or in droplets. CH 3 is primarily produced by electron-impact of and dissociative excitation transfer to CH 4 , as well as CH 2 reacting with CH 4 . CH 3 is rapidly consumed to form C 2 H 6 which, in spite of being subject to these same dissociative processes, accumulates over time, as do other stable products including C 3 H 8 and CH 3 OH. The gas mixture and electrical properties were varied to assess their effects on CH 3 production. CH 3 production is largest with 5% CH 4 in the Ar/CH 4 /H 2 O mixture due to an optimal balance of electron-impact dissociation, which increases with CH 4 percentage, and dissociative excitation transfer and CH 2 reacting with CH 4 , which decrease with CH 4 percentage. Design parameters of the microchannels were also investigated. Increasing the permittivity of the dielectrics in contact with the plasma increased the ionization wave intensity which increased CH 3 production. Increased energy deposition per pulse generally increased CH 3 production as does lengthening pulse length up to a certain point. The arrangement of the solvent flow in the microchannel can also affect the CH 3 density and fluence to the solvent. The fluence of CH 3 to the liquid solvent is increased if the liquid is immersed in the plasma as a droplet or is a layer on the wall where the ionization wave terminates. The solvation dynamics of CH 3 with varying numbers of droplets was also examined. Here, the maximum density of solvated methyl radicals CH 3aq occurs with a large number of droplets in the plasma. However, the solvated CH 3aq density can rapidly decrease due to desolvation, emphasizing the need to quickly react the solvated species in the solvent.

03 NATURAL GAS↗

DOE OSTI2026

Statistical generic design of glass and optimization: Selective review on oxide glasses

Designing a single glass composition for a multidimensional property space is challenging, and the difficulty increases with the number of design criteria. Traditionally, the task is accomplished using multiple statistical models that describe the relationships between composition (C) and property (P) values, i.e., C-P models. Recently, the structure (S)-property (P) statistical modeling has emerged as a complementary approach. The S-P modeling approach has also been shown to be a preferred method for modeling glass properties, particularly when a small data set is available, such as in single-component studies, or when strong nonlinearities exist between composition and properties. The combined model package, C-S-P, implements the concept of generic glass design, i.e., designing glass for performance by first selecting a specific or optimized set of glass network structural groups using S-P models and then transferring the designed structures (genes) to a particular composition using C-S models. This article reviews a set of supporting cases from the previous C-S-P modeling studies of phosphate, silicate, and borosilicate glasses, which are relevant for many critical commercial applications. The methodology for developing the statistical C-S-P database is presented, enabling the application of P?S?C to achieve a generic glass design and optimization, targeting multiple design criteria for both performance and processing properties simultaneously.

Network structure↗