SEARCH · Engineering Papers

Results for “traces”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 973 records · Page 54

All sources NASA NTRS DOE OSTI

DOE OSTI2023

Model predictive control of mixing controlled compression ignition operation for low reactivity fuels

Using gasoline or other low reactivity fuels with a pilot injection or port fuel injection in a compression ignition engine has shown great potential in reducing NOx emissions while keeping high thermal efficiency compared to diesel. However, excessive combustion noise is caused by a high maximum pressure rise rate in the cylinder due to the higher fractions of premixed charge of the low-reactivity fuel. This noise can result in structural damage to engine components and as such, combustion noise limits the range of the operating parameters and makes the control of such engines challenging. In this study, a simulation environment was built up in MATLAB/Simulink leveraging a physics-based zero-dimension combustion model to capture the in-cylinder pressure time traces as well as metrics relevant to thermal efficiency and combustion noise. Here, in order to also facilitate the control of emissions, machine learning models were investigated to capture NOx emissions. A kernel-based extreme learning machine (K-ELM) performed best and had a coefficient of correlation (R-squared) of 0.998. The combustion and NOx emission models are valid for not only conventional gasoline fuel but also oxygenated alternative fuel blends at three different pilot injection strategies. In order to track key combustion metrics while keeping noise and emissions within constraints, a model predictive control (MPC) was applied for a compression ignition engine operating with a range of potential fuels and fuel injection strategies. The MPC is validated under different scenarios, including a load step change, fuel type change, and injection strategy change, with proportional–integral (PI) control as the baseline. The simulation results show that MPC reduces about 26% of ringing intensity in the transient process and 17% at the steady state for E30. Generally, MPC can optimize the overall performance through modifying the main injection timing, pilot fuel mass, and exhaust gas recirculation (EGR) fraction.

42 ENGINEERING↗

DOE OSTI2025

Biotechnological solutions for critical mineral recovery from unconventional feedstocks

Secure and sustainable metal recovery from unconventional feedstocks is needed to meet the mineral demands of energy, defense, and electronic technologies. Here, we highlight the potential to leverage nature’s ability to extract and differentiate metal ions in biotechnologies that could become the next generation of mining and refining. We describe bulk and trace processes and then discuss the advances and opportunities of two key bioprocesses: microbially mediated solubilization of metal ions from solid matrices (termed ‘bioleaching’) and bio-based separation of solubilized ions via selective adsorption to proteins. Both biotechnologies have advantages such as reduced energy input for leaching low-grade feedstocks and reduced organic solvent demand for separating ions with similar physiochemical properties but require more development for industrial scale recovery from unconventional feedstocks. Innovation in biological science and engineering may bring timely solutions to key challenges toward recovering critical minerals from unconventional feedstocks.

organic↗

DOE OSTI2021

Electrochemical stability, physical, and electronic properties of thermally pre-formed oxide compared to artificially sputtered oxide on Fe thin films in aqueous chloride

Here the electrochemical stability and corrosion behavior of the thermally pre-oxidized and sputter deposited variant of an oxide single-crystalline Fe thin film were compared. Thermal oxides formed Fe 2 O 3 over an inner layer of Fe 3 O 4 while the sputtered oxides were found to have grown Fe 3 O 4 instead of the target stoichiometry of Fe 2 O 3 . Oxide films of both types were stable in pH=9.3 borate buffer solution, however, were altered in pH=9.3, 0.1 M NaCl solution in the case of thermally pre-oxidized Fe thin film. The stability of the oxide differed in pH=4, 0.1 M NaCl where sputtered Fe films were more stable against acidic chemical dissolution than the thermally formed Fe oxide film. These differences were traced by AC/DC electrochemical analysis including electronic defect densities, and molecular identity characterized by ex-situ X-ray photoelectron spectroscopy.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2025

Historic and modern nuclear graphite impurities: Pathways to improved waste strategies

Graphite has been used in large volumes as a structural material and neutron moderator since the earliest days of nuclear fission. However, no international consensus exists on the disposal of irradiated graphite, leaving much of the historic radioactive graphite inventory in interim vault or silo storage. With several new graphite-moderated reactors planned or under construction, the issue of graphite waste management is becoming increasingly urgent. This paper reviews and quantifies impurities in both historic and modern nuclear graphite, with emphasis on nitrogen—responsible for much of the 14 C inventory—and chlorine, which plays a critical role in repository performance and design. Modern graphites, benefitting from stringent quality-control measures developed for non-nuclear industries, meet or exceed the ASTM Ultra-High Purity nuclear standards, even without halide purification. Both chlorine and nitrogen concentrations have declined over time. For chlorine, identified as a key impurity influencing U.S. waste repository design, we propose a target of 0.1 appm in as-fabricated billets as a reasonable benchmark. Nitrogen sources are traced throughout the graphite production process, with surface and bulk concentrations characterized for all materials studied. Modern graphites commonly exhibit nitrogen levels below 5 appm, with values approaching 1 appm achievable. Using such reduced-nitrogen grades is critical to keeping graphite-induced radioactivity below the greater-than-Class-C waste threshold, thereby avoiding disposal cost penalties of nearly an order of magnitude.

Chlorine↗

DOE OSTI2025

A provably stable numerical method for the anisotropic diffusion equation in confined magnetic fields

We present a novel numerical method for solving the anisotropic diffusion equation in magnetic fields confined to a periodic box which is accurate and provably stable. We derive energy estimates of the solution of the continuous initial boundary value problem. A discrete formulation is presented using operator splitting in time with the summation by parts finite difference approximation of spatial derivatives for the perpendicular diffusion operator. Weak penalty procedures are derived for implementing both boundary conditions and parallel diffusion operator obtained by field line tracing. We prove that the fully-discrete approximation is unconditionally stable. Discrete energy estimates are shown to match the continuous energy estimate given the correct choice of penalty parameters. A nonlinear penalty parameter is shown to provide an effective method for tuning the parallel diffusion penalty and significantly minimises rounding errors. Several numerical experiments, using manufactured solutions, the “NIMROD benchmark” problem and a single island problem, are presented to verify numerical accuracy, convergence, and asymptotic preserving properties of the method. Finally, we present a magnetic field with chaotic regions and islands and show the contours of the anisotropic diffusion equation reproduce key features in the field.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2024

Alkaloids are associated with increased microbial diversity and metabolic function in poison frogs

Shifts in host-associated microbiomes can impact both host and microbes. It is of interest to understand how perturbations, like the introduction of exogenous chemicals, impact microbiomes. In poison frogs (family Dendrobatidae), the skin microbiome is exposed to alkaloids that the frogs sequester for defense. These alkaloids are antimicrobial; however, their effect on the frogs’ skin microbiome is unknown. To test this, we characterized microbial communities from field-collected dendrobatid frogs. Then, we conducted a laboratory experiment to monitor the effect of the alkaloid decahydroquinoline (DHQ) on the microbiome of two frog species with contrasting alkaloid loads in nature. In both datasets, we found that alkaloid-exposed microbiomes were more phylogenetically diverse, with an increase in diversity among rare taxa. Further, to better understand the isolate-specific response to alkaloids, we cultured microbial isolates from poison frog skin and found that many isolates exhibited enhanced growth or were not impacted by the addition of DHQ. To further explore the microbial response to alkaloids, we sequenced the metagenomes from high- and low-alkaloid frogs and observed a greater diversity of genes associated with nitrogen and carbon metabolism in high-alkaloid frogs. From these data, we hypothesized that some strains may metabolize the alkaloids. We used stable isotope tracing coupled to nanoSIMS (nanoscale secondary ion mass spectrometry), which supported the idea that some of these isolates are able to metabolize DHQ. Together, these data suggest that poison frog alkaloids open new niches for skin-associated microbes with specific adaptations, such as alkaloid metabolism, that enable survival in this environment.

59 BASIC BIOLOGICAL SCIENCES↗

DOE OSTI2026

Discovery of additional ancient genome duplications in yeasts

Whole-genome duplication (WGD) has had profound macroevolutionary impacts on diverse lineages, preceding adaptive radiations in vertebrates, teleost fish, and angiosperms. In contrast to the many known ancient WGDs in animals, and especially plants, we are aware of evidence for only four WGDs in fungi. The oldest of these occurred ∼100 million years ago (mya) and is shared by ∼60 extant Saccharomycetales species, including the baker’s yeast Saccharomyces cerevisiae. Notably, this is the only known ancient WGD event in the yeast subphylum Saccharomycotina. The dearth of ancient WGD events in fungi remains a mystery. Some studies have suggested that fungal lineages that experience chromosome and genome duplication quickly go extinct, leaving no trace in the genomic record, while others contend that the lack of known WGDs is due to an absence of data. Under the second hypothesis, additional sampling and deeper sequencing of fungal genomes should lead to the discovery of more WGD events. Coupling hundreds of recently published genomes from nearly every described Saccharomycotina species, with three additional long-read assemblies, we discovered three novel WGD events. Although the functions of retained duplicate genes originating from these events are broad, they bear similarities to the well-known WGD that occurred in the Saccharomycetales. In conclusion, our results suggest that WGD may be a more common evolutionary force in fungi than previously believed.

convergent evolution↗

DOE OSTI2021

A census of the lung: CellCards from LungMAP

The human lung plays vital roles in respiration, host defense, and basic physiology. Recent technological advancements such as single-cell RNA sequencing and genetic lineage tracing have revealed novel cell types and enriched functional properties of existing cell types in lung. The time has come to take a new census. Initiated by members of the NHLBI-funded LungMAP Consortium and aided by experts in the lung biology community, we synthesized current data into a comprehensive and practical cellular census of the lung. Identities of cell types in the normal lung are captured in individual cell cards with delineation of function, markers, developmental lineages, heterogeneity, regenerative potential, disease links, and key experimental tools. This publication will serve as the starting point of a live, up-to-date guide for lung research at https://www.lungmap.net/cell-cards/. We hope that Lung CellCards will promote the community-wide effort to establish, maintain, and restore respiratory health.

COVID↗

DOE OSTI2020

Optical measure of disorder: Why Urbach analysis works for amorphous silicon but fails for amorphous carbon

We investigate the basis for the Paradox where the Urbach-slope disorder parameter disagrees with the Raman width in amorphous diamond-like carbon (DLC) materials (lower Urbach-Eo yet greater Raman width). We examined the bandgap and Urbach-slope measurement issues. While significant errors are identified, ultimately these cannot resolve the Paradox. This resolution involves large changes in shape of DLC's absorption band resulting from large energy shifts. To solidify the understanding of band energy shifts, we examined their properties using a-Si:H, well known for its agreement between Raman and Urbach-slope disorder parameters. Using Tauc-Lorentz (T-L) dispersion functions, the Urbach method works for a-Si:H because small changes in shape occur, as measured by (i) peak position, (ii) peak width, (iii) peak amplitude, and (iv) and gap energies. Moreover, for a-Si:H, a 5th condition (v) there is no other feature below the principal band to interfere with its fall. All 5 of these conditions fail for DLCs. Because T-L dispersions accommodate asymmetry, we traced the Paradox to a steepening of the band shape as it pushes toward lower energy. This steepening is unrelated to disorder, but to a boundary value problem where energy cannot be negative. We conclude that Urbach analysis is invalid for DLC materials, but the T-L width is a good measure instead. We also examined another disorder measure, where π bonds should be considered as disorder relative to the σ bonds in an idealized “amorphous diamond” sp 3 network: superconvergence can be used to quantify these π transitions. Finally, further molecular orbital calculations are needed to properly interpret the changes in T-L widths.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Determination of impurities in cubic boron nitride (cBN) by inductively coupled plasma mass spectrometry (ICPMS)

The phase stability of cBN is critically dependent on the content and amount of impurities present. While studies have shown qualitatively that the addition of certain impurities can either increase or decrease the cBN-hBN phase transition temperature, studies have yet to show this effect quantitatively. This is because analytical methods to characterize minor and trace impurities in cBN are currently lacking. To this end, we present flux fusion methods capable of fully digesting cBN samples for ICPMS analyses. The materials used in this study are commercially available cBN powders in three different sizes. Two types of fluxes (LiOH and NaOH·H 2 O) are utilized so that both Li and Na impurities can be determined. To ensure the accuracy of Si measurements, a column chromatography method has been developed to purify Si from flux materials in order to increase the amount of dissolved sample sent to the ICP. Detection limits have been determined using procedural blanks and are found to be below 20 μg/g for all 58 elements analyzed except for Si, for which the detection limit is 312 μg/g. Nonetheless, all cBN powders studied are found to have high Si impurity levels that are above detection limit. This study provides a much-needed analytical protocol to enable comprehensive screening of impurities in cBN.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Linking habitat suitability with a longleaf pine-hardwood model: Building a species-predictive fire-land management framework

Active management of fire-dependent ecosystems for specific species leads to complex tradeoffs, which affect conservation outcomes to other species. Therefore a multi-species evaluation of management actions is required. Habitat Suitability Models (HSMs) can help in predicting the likelihood of species occurrence using corresponding environmental variables and empirical relationships that link occurrence with specific environmental conditions. Incorporating multiple species into HSMs and relating them to habitat dynamics is crucial for ecosystems that require active management with prescribed fire. To address this issue, we developed multi-species HSM driven within an existing population model of the longleaf pine-hardwood ecosystem to assess the suitability of an ecosystem given different fire management strategies and environmental conditions. The population model used in this study provides spatial and temporal changes of longleaf pine-hardwood habitat structure in response to fire. These habitat values are used by the HSM to calculate habitat suitability for three threatened and endangered faunal species of this ecosystem, which all thrive with frequent fire, but have unique habitat requirements. Transient habitat conditions are traced to predict longleaf pine ecosystem trajectories under various management strategies, thereby evaluating current land management actions, such as thinning or prescribed fire frequencies. We tested a suite of environmental conditions to emphasize the sensitivity of the species to different fire management actions. The results of our modeling suggest that maximum suitable habitat for all three species can be achieved with fire frequency occurring at approximately once every three years. The modeling results support current management actions and provide a new habitat assessment tool that incorporates ecological factors for multiple species, thus providing for habitat optimization.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2020

Interface stability of LiCl-rich argyrodite Li 6 PS 5 Cl with propylene carbonate boosts high-performance lithium batteries

In solid-state lithium (Li)-metal batteries (SSLMBs), sulfide-based Li-ion conductors represent one of the most popular solid electrolytes (SEs). However, the development of sulfide-based SSLMBs is significantly hampered by interfacial issues including large solid-solid contact resistance and serious side reactions at the SE/electrode interface. To address these issues, here, we demonstrated a simple and efficient strategy by using LiCl-rich argyrodite Li 6 PS 5 Cl (Li 6 PS 5 Cl-LiCl) SE and trace amount of propylene carbonate (PC) at the SE/electrode interface to facilitate the formation of stable and robust solid electrolyte interphase (SEI). Additionally, the formed SEI not only serves as a buffer layer to passivate the interfacial reactions and suppress Li dendrite growth, but also acts as a bridge for Li-ion conduction to reduce the contact resistance. As a result, the Li||Li symmetric cell exhibited long-term electrochemical cycling stability over 1000 h at a current density of 0.2 mA cm -2 . Furthermore, the assembled Li||Li 4 Ti 5 O 12 (LTO) batteries delivered a specific capacity of 175 mAh g–1 at 0.2 C, and remained an excellent specific capacity of 116 mAh g –1 after 200 cycles at a high current rate of 1 C. These features indicate a feasible strategy to enhance the interfacial property of high-performance SSLMBs.

25 ENERGY STORAGE↗

DOE OSTI2022

Understanding the p-doping of spiroOMeTAD by tris(pentafluorophenyl)borane

The solid-state organization of photoabsorber, hole and electron transporting layers, and interfaces between them plays an important role in governing the performance and stability of emerging optoelectronic devices such as perovskite solar cells (PSCs). The molecular organic semiconductor (OSC) 2,2' ,7,7' -tetrakis [N,N-di(4-methoxyphenyl)amino]-9,9'-spirobifluorene (spiroOMeTAD) is a promising hole-transporting material (HTM) for PSCs, which is p-doped by molecular dopants to augment the charge carrier mobility. Here, the p-type doping of spiroOMeTAD by tris(pentafluorophenyl)borane (BCF) is investigated by a combination of techniques including optical spectroscopy, X-ray diffraction, Fourier transform infrared (FTIR), solid-state (ss)NMR, and electron paramagnetic resonance (EPR) spectroscopy. BCF molecules interact with traces of water molecules to form BCF-water complexes. Optical spectroscopy analysis suggests that the BCF/BCF-water complexes oxidize spiroOMeTAD molecules and facilitate p-type doping of spiroOMeTAD molecules. The different distributions of BCF and BCF-water molecules in doped spiroOMeTAD are characterized by FTIR and 11B NMR spectroscopy. An NMR crystallography approach which combines two-dimensional (2D) ssNMR and crystallography modeling is employed to unravel the packing interactions in spiroOMeTAD, and this analysis is extended to probe the morphological and structural changes in spiroOMeTAD:BCF blends. The hyperfine interactions are characterized by 2D hyperfine sub-level correlation (HYSCORE) spectroscopy. In this way, insight into the complex spiroOMeTAD:BCF blend morphology is obtained and compared for different dopant concentrations. Further, molecular-level analysis of doped HTMs enabled by this study has much wider relevance for further investigation, for example, chemical design and interfacial engineering of p-type doped HTMs for stable and efficient hybrid perovskite photovoltaics.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2021

Theory of subcycle time-resolved photoemission: Application to terahertz photodressing in graphene

Here, motivated by recent experimental progress we revisit the theory of pump–probe time- and angle-resolved photoemission spectroscopy (trARPES), which is one of the most powerful techniques to trace transient pump-driven modifications of the electronic properties. The pump-induced dynamics can be described in different gauges for the light–matter interaction. Standard minimal coupling leads to the velocity gauge, defined by linear coupling to the vector potential. In the context of tight-binding (TB) models, the Peierls substitution is the commonly employed scheme for single-band models. Multi-orbital extensions – including the coupling of the dipole moments to the electric field – have been introduced and tested recently. In this work, we derive the theory of time-resolved photoemission within both gauges from the perspective of nonequilibrium Green’s functions. This approach naturally incorporates the photoelectron continuum, which allows for a direct calculation of the observable photocurrent. Following this route we introduce gauge-invariant expressions for the time-resolved photoemission signal. The theory is applied to graphene pumped with short terahertz pulses, which we treat within a first-principles TB model. We investigate the gauge invariance and discuss typical effects observed in subcycle time-resolved photoemission. Our formalism is an ideal starting point for realistic trARPES simulations including scattering effects.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

DOE OSTI2026

Hierarchical semi-Markov models with duration-aware dynamics for activity sequences

Residential electricity demand at granular scales is driven by what people do and for how long. Accurately forecasting this demand for applications like microgrid management and demand response therefore requires generative models for activities that can produce realistic daily activity sequences, capturing both the timing and duration of human behavior. This paper develops a generative model of human activity sequences using nationally representative time-use diaries at a 10-min resolution. We use this model to quantify which demographic factors are most critical for improving predictive performance. We propose a hierarchical semi-Markov framework that addresses two key modeling challenges. First, a time-inhomogeneous Markov router learns the patterns of “which activity comes next.” Second, a semi-Markov hazard component explicitly models activity durations, capturing “how long” activities realistically last. To ensure statistical stability when data are sparse, the model pools information across related demographic groups and time blocks. The entire framework is trained and evaluated using survey design weights to ensure our findings are representative of the U.S. population. On a held-out test set, we demonstrate that explicitly modeling durations with the hazard component provides a substantial and statistically significant improvement over purely Markovian models. Furthermore, our analysis reveals a clear hierarchy of demographic factors: Sex, Day-Type, and Household Size provide the largest predictive gains, while Region and Season, though important for energy calculations, contribute little to predicting the activity sequence itself. The result is an interpretable and robust generator of synthetic activity traces, providing a high-fidelity foundation for downstream energy systems modeling.

24 POWER TRANSMISSION AND DISTRIBUTION↗

DOE OSTI2021

A first and second law analysis of a thermoresponsive polymer desiccant dehumidification and cooling cycle

Herein, we present a theoretical description for a new desiccant air conditioning cycle that uses thermoresponsive polymers instead of traditional desiccants. We use a combined first and second law analysis to demonstrate that this new cycle has three major advantages relative to the traditional case: (i) it can regenerate at lower temperatures, (ii) it can harvest liquid water and (iii) it has significantly higher coefficients of performance (COPs). For example, this new cycle can achieve a COP of 5.1 when regenerated at 95 degrees C, whereas the traditional desiccant cycle is limited to a COP of ~ 1. The fundamental origins of these advantages can be traced to the method of regeneration. The traditional desiccant cycle regenerates by flowing hot air over the desiccant, which provides a medium for gaseous water desorption. However, this also generates entropy and places a minimum temperature constraint on the hot air. In contrast, the thermoresponsive polymer cycle regenerates through a polymer phase transition. The polymer absorbs water vapor in humid air, and then it expels liquid water when raised above its transition temperature. This regeneration method generates liquid water that can be harvested and relaxes constraints on entropy generation and minimum temperature. The minimum regeneration temperature of the thermoresponsive cycle is only limited by the transition temperature of the polymer, which can be tuned through materials science. Due to its liquid water harvesting capability, the new cycle potentially eliminates water consumption when used with evaporative cooling, or it can be directly used for atmospheric water harvesting.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

DOE OSTI2020

The direct and indirect effects of copper on vector-borne disease dynamics

Metal pollution is a growing concern that affects the health of humans and animals globally. Copper is an essential insect micronutrient required for respiration, pigmentation and oxidative stress protection but can also act as a potentially toxic trace element. While several studies have focused on the negative fitness effects of copper on the aquatic larvae of mosquitoes, the effects of larval copper exposure on adult mosquito fitness (i.e., survival and fecundity) and their ability to transmit parasites (i.e., vector competence) remains unclear. Here, using a well-studied model vector-parasite system, the mosquito Aedes aegypti and parasite Dirofilaria immitis, we show that sublethal copper exposure in larval mosquitoes alters adult female fecundity and vector competence. Specifically, mosquitoes exposed to copper had a hormetic fecundity response and mosquitoes exposed to 600 μg/L of copper had significantly fewer infective parasite larvae than control mosquitoes not exposed to copper. Therefore, exposure of mosquito larvae to copper levels far below EPA-mandated safe drinking water limits (1300 μg/L) can impact vector-borne disease dynamics not only by reducing mosquito abundance (through increased larval mortality), but also by reducing parasite transmission risk. Our results also demonstrated that larval copper is retained through metamorphosis to adulthood in mosquitoes, indicating that these insects could transfer copper from aquatic to terrestrial foodwebs, especially in urban areas where they are abundant. To our knowledge this is the first study to directly link metal exposure with vector competence (i.e., ability to transmit parasites) in any vector-parasite system. Additionally, it also demonstrates unequivocally that mosquitoes can transfer contaminants from aquatic to terrestrial ecosystems. These results have broad implications for public health because they directly linking contaminants and vector-borne disease dynamics, as well as linking mosquitoes and contaminant dynamics.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2021

The evolution of seafloor venting from hydrate-sealed gas reservoirs

Here we use 3D seismic data to show that three rows of seafloor gas mounds can be traced downward to leak points that lie at the hydrate-gas contact within three individual dipping coarse-grained sand bodies in the Terrebonne Basin, Walker Ridge block 313, northern Gulf of Mexico. We predict the overpressure within the sand bodies by assuming that the gas pressure at the vent points equal the least principal stress. We interpret that free gas accumulates at the base of the hydrate stability zone, trapped by the overlying sand which has a high methane hydrate saturation. The free gas accumulates until the gas pressure at the base of the hydrate stability zone reaches the least principal stress in the overlying mudrock, whereupon hydraulic fractures form and fluids are vented to the surface. The warm rising fluids and perhaps localized exothermic formation of hydrate raise the local salinity and temperature. This process progressively shifts the base of the hydrate stability zone to shallower depths and dissociates the hydrate seal within the sand, which creates new leak points and results in the observed migration of the seafloor vents. Within the southwest corner of the Terrebonne Basin, this process has repeated multiple times within the Blue, Orange, and Green sands. Here this study shows how the hydrate stability zone can influence the location of fluid expulsion and in turn be affected by the warm, rising, saline fluids sealed by hydrate.

58 GEOSCIENCES↗