Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “software: simulations”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 973 records · Page 54
All sourcesNASA NTRSDOE OSTI
NASA NTRS2007

Potential of VIIRS Data for Regional Monitoring of Gypsy Moth Defoliation: Implications for Forest Threat Early Warning System

A NASA RPC (Rapid Prototyping Capability) experiment was conducted to assess the potential of VIIRS (Visible/Infrared Imager/Radiometer Suite) data for monitoring non-native gypsy moth (Lymantria dispar) defoliation of forests. This experiment compares defoliation detection products computed from simulated VIIRS and from MODIS (Moderate Resolution Imaging Spectroradiometer) time series products as potential inputs to a forest threat EWS (Early Warning System) being developed for the USFS (USDA Forest Service). Gypsy moth causes extensive defoliation of broadleaved forests in the United States and is specifically identified in the Healthy Forest Restoration Act (HFRA) of 2003. The HFRA mandates development of a national forest threat EWS. This system is being built by the USFS and NASA is aiding integration of needed satellite data products into this system, including MODIS products. This RPC experiment enabled the MODIS follow-on, VIIRS, to be evaluated as a data source for EWS forest monitoring products. The experiment included 1) assessment of MODIS-simulated VIIRS NDVI products, and 2) evaluation of gypsy moth defoliation mapping products from MODIS-simulated VIIRS and from MODIS NDVI time series data. This experiment employed MODIS data collected over the approximately 15 million acre mid-Appalachian Highlands during the annual peak defoliation time frame (approximately June 10 through July 27) during 2000-2006. NASA Stennis Application Research Toolbox software was used to produce MODIS-simulated VIIRS data and NASA Stennis Time Series Product Tool software was employed to process MODIS and MODIS-simulated VIIRS time series data scaled to planetary reflectance. MODIS-simulated VIIRS data was assessed through comparison to Hyperion-simulated VIIRS data using data collected during gypsy moth defoliation. Hyperion-simulated MODIS data showed a high correlation with actual MODIS data (NDVI R2 of 0.877 and RMSE of 0.023). MODIS-simulated VIIRS data for the same date showed moderately high correlation with Hyperion-simulated VIIRS data (NDVI R2 of 0.62 and RMSE of 0.035), even though the datasets were collected about a half an hour apart during changing weather conditions. MODIS products (MOD02, MOD09, and MOD13) and MOD02-simulated VIIRS time series data were used to generate defoliation mapping products based on image classification and image differencing change detection techniques. Accuracy of final defoliation mapping products was assessed by image interpreting over 170 randomly sampled locations found on Landsat and ASTER data in conjunction with defoliation map data from the USFS. The MOD02-simulated VIIRS 400-meter NDVI classification produced a similar overall accuracy (87.28 percent with 0.72 Kappa) to the MOD02 250-meter NDVI classification (86.71 percent with 0.71 Kappa). In addition, the VIIRS 400-meter NDVI, MOD02 250-meter NDVI, and MOD02 500-meter NDVI showed good user and producer accuracies for the defoliated forest class (70 percent) and acceptable Kappa values (0.66). MOD02 and MOD02-simulated VIIRS data both showed promise as data sources for regional monitoring of forest disturbance due to insect defoliation.

Spruce, Joseph P.↗
NASA NTRS1983

Development of the functional simulator for the Galileo attitude and articulation control system

A simulation program for verifying and checking the performance of the Galileo Spacecraft's Attitude and Articulation Control Subsystem's (AACS) flight software is discussed. The program, which is called Functional Simulator (FUNSIM), provides a simple method of interfacing user-supplied mathematical models coded in FORTRAN which describes spacecraft dynamics, sensors, and actuators; this is done with the AACS flight software, coded in HAL/S (High-level Advanced Language/Shuttle). It is thus able to simulate the AACS flight software accurately to the HAL/S statement level in the environment of a mainframe computer system. FUNSIM also has a command and data subsystem (CDS) simulator. It is noted that the input/output data and timing are simulated with the same precision as the flight microprocessor. FUNSIM uses a variable stepsize numerical integration algorithm complete with individual error bound control on the state variable to solve the equations of motion. The program has been designed to provide both line printer and matrix dot plotting of the variables requested in the run section and to provide error diagnostics.

Namiri, M. K.↗
NASA NTRS1990

Modeling and simulation of the space platform power system

A comprehensive computer-aided modeling and simulation technique for the space platform power system is described. Large-signal and small-signal modeling is presented for the system components. The component models have been integrated to form the complete power system model. The system model is shown to be a powerful tool in simulating the behavior of the system with variation of illumination level and load. It can be used to study the bus regulation in each mode and to observe mode changes as the solar array is subjected to transitions from sunlight to eclipse and back to sunlight. System simulations show how the bus regulation is maintained by activating the shunt switching unit, the charger, or the discharger, depending on the available illumination level. The system model is suitable for verifying hardware results of for analyzing the performance of a proposed system where hardware testing is not feasible. The EASY5 dynamic analysis program is used as the host software for the modeling and simulation.

Patil, A. R.↗
NASA NTRS2011

Integrated Software Health Management for Aircraft GN and C

Modern aircraft rely heavily on dependable operation of many safety-critical software components. Despite careful design, verification and validation (V&V), on-board software can fail with disastrous consequences if it encounters problematic software/hardware interaction or must operate in an unexpected environment. We are using a Bayesian approach to monitor the software and its behavior during operation and provide up-to-date information about the health of the software and its components. The powerful reasoning mechanism provided by our model-based Bayesian approach makes reliable diagnosis of the root causes possible and minimizes the number of false alarms. Compilation of the Bayesian model into compact arithmetic circuits makes SWHM feasible even on platforms with limited CPU power. We show initial results of SWHM on a small simulator of an embedded aircraft software system, where software and sensor faults can be injected.

Schumann, Johann↗
NASA NTRS2011

iPAS Propulsion Subsystem

The ultimate goal of the Integrated Power, Avionics and Software (iPAS) project is to develop a simulation facility that can be apply to various missions that use common avionics, hardware, and software architecture. The iPAS facility will model several subsystems, the EP4 contribution to the project is to design and build a low fidelity representation of the in-space propulsion system for the iPAS simulation. The system would use a pressurized bottle to provide the gas for the thrusters. Air will be used to perform the simulation to prevent a hazardous environment in the facility. Three cold gas thrusters previously used for the X-38 program will be used for the simulation because they are on hand and available for use. An incremental design-build-test approach will be taken where the X-38 thrusters may be replaced with actual flight thrusters as the flight design is matured. A pressurized system must be designed, built, and tested to reduce the 2,400psi bottle pressure to a reasonable pressure (0-800psig) to minimize the amount of noise created upon thruster activation. Once all the subsystems are completed they will be integrated together for testing.

Sanchez, Rodrigo↗
NASA NTRS2017

Aeroacoustic Simulations of a Nose Landing Gear with FUN3D: A Grid Refinement Study

A systematic grid refinement study is presented for numerical simulations of a partially-dressed, cavity-closed (PDCC) nose landing gear configuration that was tested in the University of Florida's open-jet acoustic facility known as the UFAFF. The unstructured-grid flow solver FUN3D is used to compute the unsteady flow field for this configuration. Mixed-element grids generated using the Pointwise (Registered Trademark) grid generation software are used for numerical simulations. Particular care is taken to ensure quality cells and proper resolution in critical areas of interest in an effort to minimize errors introduced by numerical artifacts. A set of grids was generated in this manner to create a family of uniformly refined grids. The finest grid was then modified to coarsen the wall-normal spacing to create a grid suitable for the wall-function implementation in FUN3D code. A hybrid Reynolds-averaged Navier-Stokes/large eddy simulation (RANS/LES) turbulence modeling approach is used for these simulations. Time-averaged and instantaneous solutions obtained on these grids are compared with the measured data. These CFD solutions are used as input to a FfowcsWilliams-Hawkings (FW-H) noise propagation code to compute the farfield noise levels. The agreement of the computed results with the experimental data improves as the grid is refined.

Vatsa, Veer N.↗
NASA NTRS2010

Designing and Implementing an OVERFLOW Reader for ParaView and Comparing Performance Between Central Processing Units and Graphical Processing Units

In the Applied Aerosciences and CFD branch at Johnson Space Center, computational simulations are run that face many challenges. Two of which are the ability to customize software for specialized needs and the need to run simulations as fast as possible. There are many different tools that are used for running these simulations and each one has its own pros and cons. Once these simulations are run, there needs to be software capable of visualizing the results in an appealing manner. Some of this software is called open source, meaning that anyone can edit the source code to make modifications and distribute it to all other users in a future release. This is very useful, especially in this branch where many different tools are being used. File readers can be written to load any file format into a program, to ease the bridging from one tool to another. Programming such a reader requires knowledge of the file format that is being read as well as the equations necessary to obtain the derived values after loading. When running these CFD simulations, extremely large files are being loaded and having values being calculated. These simulations usually take a few hours to complete, even on the fastest machines. Graphics processing units (GPUs) are usually used to load the graphics for computers; however, in recent years, GPUs are being used for more generic applications because of the speed of these processors. Applications run on GPUs have been known to run up to forty times faster than they would on normal central processing units (CPUs). If these CFD programs are extended to run on GPUs, the amount of time they would require to complete would be much less. This would allow more simulations to be run in the same amount of time and possibly perform more complex computations.

Chawner, David M.↗
NASA NTRS2015

Aeroacoustic Simulations of a Nose Landing Gear Using FUN3D on Pointwise Unstructured Grids

Numerical simulations have been performed for a partially-dressed, cavity-closed (PDCC) nose landing gear configuration that was tested in the University of Florida's open-jet acoustic facility known as the UFAFF. The unstructured-grid flow solver FUN3D is used to compute the unsteady flow field for this configuration. Mixed-element grids generated using the Pointwise(TradeMark) grid generation software are used for these simulations. Particular care is taken to ensure quality cells and proper resolution in critical areas of interest in an effort to minimize errors introduced by numerical artifacts. A hybrid Reynolds-averaged Navier-Stokes/large eddy simulation (RANS/LES) turbulence model is used for these simulations. Solutions are also presented for a wall function model coupled to the standard turbulence model. Time-averaged and instantaneous solutions obtained on these Pointwise grids are compared with the measured data and previous numerical solutions. The resulting CFD solutions are used as input to a Ffowcs Williams-Hawkings noise propagation code to compute the farfield noise levels in the flyover and sideline directions. The computed noise levels compare well with previous CFD solutions and experimental data.

Vatsa, Veer N.↗
NASA NTRS2017

OpenSatKit Enables Quick Startup for CubeSat Missions

The software required to develop, integrate, and operate a spacecraft is substantial regardless of whether its a large or small satellite. Even getting started can be a monumental task. To solve this problem, NASAs Core Flight System (cFS), NASA's 42 spacecraft dynamics simulator, and Ball Aerospaces COSMOS ground system have been integrated together into a kit called OpenSatKit that provides a complete and open source software solution for starting a new satellite mission. Users can have a working system with flight software, dynamics simulation, and a ground command and control system up and running within hours.Every satellite mission requires three primary categories of software to function. The first is Flight Software (FSW) which provides the onboard control of the satellites and its payload(s). NASA's cFS provides a great platform for developing this software. Second, while developing a satellite on earth, it is necessary to simulate the satellites orbit, attitude, and actuators, to ensure that the systems that control these aspects will work correctly in the real environment. NASAs 42 simulator provides these functionalities. Finally, the ground has to be able to communicate with the satellite, monitor its performance and health, and display its data. Additionally, test scripts have to be written to verify the system on the ground. Ball Aerospace's COSMOS command and control system provides this functionality. Once the OpenSatKit is up and running, the next step is to customize the platform and get it running on the end target. Starting from a fully working system makes porting the cFS from Linux to a users platform much easier. An example Raspberry Pi target is included in the kit so users can gain experience working with a low cost hardware target. All users can benefit from OpenSatKit but the greatest impact and benefits will be to SmallSat missions with constrained budgets and small software teams. This paper describes OpenSatKits system design, the steps necessary to run the system to target the Raspberry Pi, and future plans. OpenSatKit is a free fully functional spacecraft software system that we hope will greatly benefit the SmallSat community.

Software↗
NASA NTRS1972

Improvements to information management systems simulator

The performance of personnel in the augmentation and improvement of the interactive IMSIM information management simulation model is summarized. With this augmented model, NASA now has even greater capabilities for the simulation of computer system configurations, data processing loads imposed on these configurations, and executive software to control system operations. Through these simulations, NASA has an extremely cost effective capability for the design and analysis of computer-based data management systems.

Bilek, R. W.↗
NASA NTRS1981

Air Combat Simulator

By adapting COSMIC's One-on-One Adaptive Maneuvering Logic (AML) for two versus one simulation, Link Division was able to reduce software and other design/development costs. Enhancements to the AML program developed by Link for simulation of two-versus one combat, two trainees can simultaneously engage a computer driven target, thereby doubling the training utility of the simulator.

Source record↗
NASA NTRS2016

Human Exploration Spacecraft Testbed for Integration and Advancement (HESTIA)

The proposed paper will cover ongoing effort named HESTIA (Human Exploration Spacecraft Testbed for Integration and Advancement), led at the National Aeronautics and Space Administration (NASA) Johnson Space Center (JSC) to promote a cross-subsystem approach to developing Mars-enabling technologies with the ultimate goal of integrated system optimization. HESTIA also aims to develop the infrastructure required to rapidly test these highly integrated systems at a low cost. The initial focus is on the common fluids architecture required to enable human exploration of mars, specifically between life support and in-situ resource utilization (ISRU) subsystems. An overview of the advancements in both integrated technologies, in infrastructure, in simulation, and in modeling capabilities will be presented, as well as the results and findings of integrated testing,. Due to the enormous mass gear-ratio required for human exploration beyond low-earth orbit, (for every 1 kg of payload landed on Mars, 226 kg will be required on Earth), minimization of surface hardware and commodities is paramount. Hardware requirements can be minimized by reduction of equipment performing similar functions though for different subsystems. If hardware could be developed which meets the requirements of both life support and ISRU it could result in the reduction of primary hardware and/or reduction in spares. Minimization of commodities to the surface of mars can be achieved through the creation of higher efficiency systems producing little to no undesired waste, such as a closed-loop life support subsystem. Where complete efficiency is impossible or impractical, makeup commodities could be manufactured via ISRU. Although, utilization of ISRU products (oxygen and water) for crew consumption holds great promise of reducing demands on life support hardware, there exist concerns as to the purity and transportation of commodities. To date, ISRU has been focused on production rates and purities for propulsion needs. The meshing of requirements between all potential users, producers, and cleaners of oxygen and water is crucial to guiding the development of technologies which will be used to perform these functions. Various new capabilities are being developed as part of HESTIA, which will enable the integrated testing of these technologies. This includes the upgrading of a 20' diameter habitat chamber to eventually support long duration (90+ day) human-in-the-loop testing of advanced life support systems. Additionally, a 20' diameter vacuum chamber is being modified to create Mars atmospheric pressures and compositions. This chamber, designated the Mars Environment Chamber (MEC), will eventually be upgraded to include a dusty environment and thermal shroud to simulate conditions on the surface of Mars. In view that individual technologies will be in geographically diverse locations across NASA facilities and elsewhere in the world, schedule and funding constraints will likely limit the frequency of physical integration. When this is the case, absent subsystems can be either digitally or physically simulated. Using the Integrated Power Avionics and Software (iPAS) environment, HESTIA is able to bring together data from various subsystems in simulated surroundings, insert faults, errors, time delays, etc., and feed data into computer models or physical systems capable of reproducing the output of the absent subsystems for the consumption of a local subsystems. Although imperfect, this capability provides opportunities to test subsystem integration and interactions at a fraction of the cost. When a subsystem technology is too immature for integrated testing, models can be produced using the General-Use Nodal Network Solver (GUNNS) capability to simulate the overall system performance. In doing so, even technologies not yet on the drawing board can be integrated and overall system performance estimated. Through the integrated development of technologies, as well as of the infrastructure to rapidly and at a low cost, model, simulate, and test subsystem technologies early in their development, HESTIA is pioneering a new way of developing the future of human space exploration.

Banker, Brian F.↗
NASA NTRS1992

Code inspection instructional validation

The Shuttle Data Systems Branch (SDSB) of the Flight Data Systems Division (FDSD) at Johnson Space Center contracted with Southwest Research Institute (SwRI) to validate the effectiveness of an interactive video course on the code inspection process. The purpose of this project was to determine if this course could be effective for teaching NASA analysts the process of code inspection. In addition, NASA was interested in the effectiveness of this unique type of instruction (Digital Video Interactive), for providing training on software processes. This study found the Carnegie Mellon course, 'A Cure for the Common Code', effective for teaching the process of code inspection. In addition, analysts prefer learning with this method of instruction, or this method in combination with other methods. As is, the course is definitely better than no course at all; however, findings indicate changes are needed. Following are conclusions of this study. (1) The course is instructionally effective. (2) The simulation has a positive effect on student's confidence in his ability to apply new knowledge. (3) Analysts like the course and prefer this method of training, or this method in combination with current methods of training in code inspection, over the way training is currently being conducted. (4) Analysts responded favorably to information presented through scenarios incorporating full motion video. (5) Some course content needs to be changed. (6) Some content needs to be added to the course. SwRI believes this study indicates interactive video instruction combined with simulation is effective for teaching software processes. Based on the conclusions of this study, SwRI has outlined seven options for NASA to consider. SwRI recommends the option which involves creation of new source code and data files, but uses much of the existing content and design from the current course. Although this option involves a significant software development effort, SwRI believes this option will produce the most effective results.

Orr, Kay↗
NASA NTRSDate not supplied

Certification Considerations for Adaptive Stress Testing of Airborne Software

eduAdaptive Stress Testing (AST) has shown promise in identifying errant corner cases in complex software used in aerospace applications including Flight Management Systems (FMS). The strength of AST is performing test-based verification of complex aerospace software intensive systems at scale in simulated operational environments.Simulating and capturing the realistic operational complexities in integrated verification environments may exposeflaws in the softwareprior to field deployment, whereas the software may perform just fine to traditional requirements-basedunit and component level testing.AST can be used to test the whole system.Individual components may behave safely, but together can result in complex interactions and emergent failures, so it is important to test at the integrated system level.Motivated by the observed benefitsat the prototype proof of concept scale, this paper considers how AST may be integrated into a production workflow and used to generate objective evidence in a processthat delivers certified aerospace software.The research includes evaluation of alignment with both DO-178C and Overarching Properties(OP). The paper addresses questions such as “where should AST fit in the Plan for Software Aspects of Certification (PSAC) and Software Verification Plan (SVP), what aspects of AST do not fit, and what objectives does it satisfy?” The paper concludes that AST is in fact useful at locating errors in complex airborne application software and in doing so provides benefits to suppliers and end users. Furthermore, AST appears appropriate to add value in both DO-178Cbased and Overarching Properties based certification approaches.

certification↗
NASA NTRS2003

Simulation-Based Verification of Livingstone Applications

AI software is viewed as a means to give greater autonomy to automated systems, capable of coping with harsh and unpredictable environments in deep space missions. Autonomous systems pose a serious challenge to traditional test-based verification approaches, because of the enormous space of possible situations that they aim to address. Before these systems are put in control of critical applications, appropriate new verification approaches need to be developed. This article describes Livingstone PathFinder (LPF), a verification tool for autonomous diagnosis applications based on NASA's Livingstone model-based diagnosis system. LPF applies state space exploration algorithms to an instrumented testbed, consisting of the Livingstone diagnosis system embedded in a simulated operating environment. The article describes different facets of LPF and reports some experimental results from applying LPF to a Livingstone model of the main propulsion feed subsystem of the X-34 space vehicle. This paper describes Livingstone PathFinder (LPF), a verification tool for autonomous diagnosis applications based on NASA's Livingstone model-based diagnosis system. LPF applies state space exploration algorithms to an instrumented testbed, consisting of the Livingstone diagnosis system embedded in a simulated operating environment. Section 2 provides an overview of Livingstone; Section 3 describes the LPF architecture; Section 4 discusses its applicability; Section 5 reviews some experimental results; Section 6 compares LPF to related verification approaches; Section 7 draws conclusions and discusses some perspectives.

Lindsey, Anthony E.↗
NASA NTRS1992

Modeling software systems by domains

The Software Architectures Engineering (SAE) Project at the Software Engineering Institute (SEI) has developed engineering modeling techniques that both reduce the complexity of software for domain-specific computer systems and result in systems that are easier to build and maintain. These techniques allow maximum freedom for system developers to apply their domain expertise to software. We have applied these techniques to several types of applications, including training simulators operating in real time, engineering simulators operating in non-real time, and real-time embedded computer systems. Our modeling techniques result in software that mirrors both the complexity of the application and the domain knowledge requirements. We submit that the proper measure of software complexity reflects neither the number of software component units nor the code count, but the locus of and amount of domain knowledge. As a result of using these techniques, domain knowledge is isolated by fields of engineering expertise and removed from the concern of the software engineer. In this paper, we will describe kinds of domain expertise, describe engineering by domains, and provide relevant examples of software developed for simulator applications using the techniques.

Dippolito, Richard↗
NASA NTRS2002

ISS Material Science Research Rack HWIL Interface Simulation

In this paper, the first Material Science Research Rack (MSRR-1) hardware-in-the-loop (HWIL) interface simulation is described. Dynamic Concepts developed this HWIL simulation system with funding and management provided by the Flight Software group (ED14) of NASA-MSFC's Avionics Department. The HWIL system has been used both as a flight software development environment and as a software qualification tool. To fulfill these roles, the HWIL simulator accurately models the system dynamics of many MSRR-1 subsystems and emulates most of the internal interface signals. The modeled subsystems include the Experiment Modules, the Thermal Environment Control System, the Vacuum Access System, the Solid State Power Controller Module, and the Active Rack Isolation Systems. The emulated signals reside on three separate MIL-STD-1553B digital communication buses, the ISS Medium Rate Data Link, and several analog controller and sensor signals. To enhance the range of testing, it was necessary to simulate several off-nominal conditions that may occur in the interfacing subsystems.

Williams, Philip J.↗
NASA NTRS1978

NOVA/IOPS - MDM/SIO - SL/BIU data transfer test software guide

The NOVA/IOPS (Input-Output Processor Simulator) is used to control all interface testing of the MDM (Multiplexer Demultiplexer) Breadboard S10 10M (serial input-output-input module) and the Matra Space Lab Inerface Unit (SL/BIU). The software handles bookkeeping such as word error rates, types of errors, display of error buffers, data display and test identification.

Source record↗