Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “scaled testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 973 records · Page 54
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

Entry heat transfer tests of the 0.006-scale space shuttle orbiter model (50-0) in Langley Research Center freon tunnel at Mach 6 (OH45)

Results are presented of heat transfer tests of a 147B configuration orbiter model (50-0) conducted in the NASA Langley Research Center Freon Tunnel (LRC/CF4). These tests were conducted at a nominal Mach number of 6, and at Reynolds numbers of 0.3 and 0.5 x 1,000,000 per foot. The objectives of the tests were to determine the effects of the low freon specific heat ratio, gamma, on the heating distributions and to determine the impingement of the orbiter bow shock on the wing. The data presented include thin skin heat transfer data (tabulated data and plotted data).

Foust, J. W.↗
NASA NTRSDate not supplied

An Overview of the NASA Lift+Cruise eVTOL Crash Test

Introduction – NASA RVLT Project Impact Dynamics / Crash Safety Task - Task Objective: “To improve the crashworthiness and impact safety of Urban Air Mobility (UAM) vehicle and provide data to simplify the certification process. Efforts will include development of validated computational models of these vehicles, as well as other impacting bodies such as birds and drones. Efforts will also focus on developing and evaluating energy absorbing and crush properties of emerging and non-traditional composite materials and processes. Finally, occupant protection will be addressed using computational models and physical assets as it pertains to all rotorcraft environments.” - Problem Statement: “There currently is a lack of data for requirements regarding the crashworthy performance of UAM vehicles and impact loads generated by a bird strike. To address this technology gap, NASA will develop test guidelines, adopt modeling methodologies demonstrating capability for ‘certification by analysis’, acquire vehicle and occupant data on full-scale representative vehicles, and provide data/guidance to consensus standards organizations and the UAM community.” - 4 Main focus points - The investigation of occupant injury using physical and computational assets - The development of energy absorbing technology - The generation of data from sub- and full-scale crash test data - The execution of advanced finite element modelling techniques

evtol↗
NASA NTRS2002

Design and Test of an Improved Crashworthiness Small Composite Airframe

The purpose of this small business innovative research (SBIR) program was to evaluate the feasibility of developing small composite airplanes with improved crashworthiness. A combination of analysis and half scale component tests were used to develop an energy absorbing airframe. Four full scale crash tests were conducted at the NASA Impact Dynamics Research Facility, two on a hard surface and two onto soft soil, replicating earlier NASA tests of production general aviation airplanes. Several seat designs and restraint systems including both an air bag and load limiting shoulder harnesses were tested. Tests showed that occupant loads were within survivable limits with the improved structural design and the proper combination of seats and restraint systems. There was no loss of cabin volume during the events. The analysis method developed provided design guidance but time did not allow extending the analysis to soft soil impact. This project demonstrated that survivability improvements are possible with modest weight penalties. The design methods can be readily applied by airplane designers using the examples in this report.

Terry, James E.↗
NASA NTRS1975

Wind tunnel tests of an 0.019-scale space shuttle integrated vehicle -2A configuration (model 14-OTS) in the NASA Ames 8 X 7 foot unitary wind tunnel, volume 3

Tests were conducted to determine the effects of cold jet gas plumes on (1) the integrated vehicle longitudinal and lateral-directional force data, (2) exposed wing hinge moment, (3) wing pressure distributions, (4) orbiter MPS external pressure distributions, and (5) model base pressures. An investigation was undertaken to determine the similarity between solid and gaseous plumes; fluorescent oil flow visualization studies were also conducted. Tabulated data listings are included.

Hardin, R. B.↗
NASA NTRS1976

Results from a convective heat transfer rate distribution test on a 0.0175 scale model (22-0) of the Rockwell International vehicle 4 space shuttle configuration in the AEDC-VKF tunnel B (OH49B), volume 1

The tests were conducted in a hypersonic wind tunnel at Mach number 8 to investigate reentry mode convective heat--transfer rates to the vehicle 4 shuttle orbiter. The thin skin thermocouple technique was used to obtain the heat transfer rate measurements. A complete set of tabulated data is presented.

Herrera, B. J.↗
NASA NTRS1985

Rotorcraft research testing in the National Full-Scale Aerodynamics Complex at NASA Ames Research Center

The unique capabilities of the National Full-Scale Aerodynamics Complex (NFAC) for testing rotorcraft systems are described. The test facilities include the 40- by 80-Foot Wind Tunnel, the 80- by 120-Foot Wind Tunnel, and the Outdoor Aerodynamic Research Facility. The Ames 7- by 10-Foot Subsonic Wind Tunnel is also used in support of the rotor research programs conducted in the NFAC. Detailed descriptions of each of the facilities, with an emphasis on helicopter rotor test capability, are presented. The special purpose rotor test equipment used in conducting helicopter research is reviewed. Test rigs to operate full-scale helicopter main rotors, helicopter tail rotors, and tilting prop-rotors are available, as well as full-scale and small-scale rotor systems for use in various research programs. The test procedures used in conducting rotor experiments are discussed together with representative data obtained from previous test programs. Specific examples are given for rotor performance, loads, acoustics, system interactions, dynamic and aeroelastic stability, and advanced technology and prototype demonstration models.

Warmbrodt, W.↗
NASA NTRS1987

Experimental evaluation of small-scale erectable truss hardware

To aid in the prediction of the dynamic behavior of the space station, a one-tenth scale dynamic test model is to be constructed of commercially available, small scale truss hardware. Tests have been performed to determine the axial stiffness characteristics and failure loads of the truss joint. A parametric study has shown that the stiffness of the joint increases as the attachment bolt torque value is increased. Furthermore, at torque values equal to or higher than 250 in-lbs, hysteresis in the load-deflection curve is essentially eliminated. Also, the joint stiffness remained relatively constant between specimens. The effective stiffness of a joint subassembly tested is 76 percent that of the strut. Tensile and compressive failure occurred in the region of the bonded plug, with lower failure loads corresponding to compressive loadings.

Mcgowan, David M.↗
NASA NTRSDate not supplied

Addressing CFM Modeling Gaps for Application into NASA’S Future Cutting Edge Missions

NASA, the US industry, and international partners are crafting frameworks to enable sustaining lunar missions. The ongoing programs, led by the agency, and prominent industry players, encompass plans for the sustained use of cryogenic propellants in lunar landers and in-space propellant refueling depots. NASA’s proactive funding initiatives have fueled the advancement of predictive computational models tailored to enhance the storage and transfer of cryogenic propellant. This paper aims to spotlight the latest advancements in this arena and delve into the collaborative efforts surrounding predictive model development within internal NASA programs as well as current and previous collaborations with industry and international partners. The paper presents an overview of recent advancements in cryogenic fluid management model development, along with their correlation with recent microgravity and large-scale cryogenic ground tests. The tests include key experiments such as the ISS Zero-Boil-Off Tank (ZBOT) series of experiments and the (Robotic Refueling Mission 3) RRM3 test during which liquid methane was stored on-orbit for an extended period of five months. The paper also highlights the anchoring of propellant tank pressurized drain tests involving sloshing that were conducted with liquid methane propellant during the Apollo/Saturn Era. Additionally, the paper discusses model anchoring against more recent sloshing tests carried out with liquid hydrogen propellant. Notable large-scale tests, such as a liquid oxygen propellant transfer test conducted by SpaceX were also used to help correlate a two-phase propellant transfer model using the valuable data measured during the test. The paper further showcases model correlations against a substantial oxygen liquefaction test undertaken by NASA to validate In-Situ-Resource-Utilization (ISRU) technologies that will prove pivotal for a sustained lunar presence.

Low-gravity fluid modeling↗
NASA NTRS2011

Large-Scale Low-Boom Inlet Test Overview

This presentation provides a high level overview of the Large-Scale Low-Boom Inlet Test and was presented at the Fundamental Aeronautics 2011 Technical Conference. In October 2010 a low-boom supersonic inlet concept with flow control was tested in the 8'x6' supersonic wind tunnel at NASA Glenn Research Center (GRC). The primary objectives of the test were to evaluate the inlet stability and operability of a large-scale low-boom supersonic inlet concept by acquiring performance and flowfield validation data, as well as evaluate simple, passive, bleedless inlet boundary layer control options. During this effort two models were tested: a dual stream inlet intended to model potential flight hardware and a single stream design to study a zero-degree external cowl angle and to permit surface flow visualization of the vortex generator flow control on the internal centerbody surface. The tests were conducted by a team of researchers from NASA GRC, Gulfstream Aerospace Corporation, University of Illinois at Urbana-Champaign, and the University of Virginia

Hirt, Stefanie↗
NASA NTRS1984

Hover test of a full-scale hingeless helicopter rotor: Aeroelastic stability, performance and loads data

A hover test of a full-scale, hingeless rotor system was conducted in the NASA Ames 40- by 80-foot wind tunnel. The rotor was tested on the Ames rotor test apparatus. Rotor aeroelastic stability, performance, and loads at various rotational speeds and thrust coefficients were investigated. The primary objective was to determine the inplane stability characteristics of the rotor system. Rotor inplane damping data were obtained for operation between 350 and 425 rpm (design speed), and for thurst coefficients between 0.0 and 0.12. The rotor was stable for all conditions tested. At constant rotor rotational speed, a minimum inplane dampling level was obtained at a thrust coefficient approximately = 0.02. At constant rotor lift, a minimum in rotor inplane damping was measured at 400 rpm.

Peterson, R. L.↗
NASA NTRS2011

The New Era of Precision Cosmology: Testing Gravity at Large Scales

Cosmic acceleration may be the biggest phenomenological mystery in cosmology today. Various explanations for its cause have been proposed, including the cosmological constant, dark energy and modified gravities. Structure formation provides a strong test of any cosmic acceleration model because a successful dark energy model must not inhibit the development of observed large-scale structures. Traditional approaches to studies of structure formation in the presence of dark energy ore modified gravity implement the Press & Schechter formalism (PGF). However, does the PGF apply in all cosmologies? The search is on for a better understanding of universality in the PGF In this talk, I explore the potential for universality and talk about what dark matter haloes may be able to tell us about cosmology. I will also discuss the implications of this and new cosmological experiments for better understanding our theory of gravity.

Prescod-Weinstein, Chanda↗
NASA NTRS1973

Wind tunnel test of the 0.010-scale space shuttle integrated vehicle in the NASA-Ames 3.5 foot hypersonic wind tunnel (IA10)

Experimental aerodynamic investigations were conducted in the NASA Ames Research Center 3.5-Foot Hypersonic Wind Tunnel on a 0.010-scale model of the space shuttle vehicle orbiter and external tank (model no. 32 0T). The purpose of the test was to evaluate the basic hypersonic stability characteristics of the external tank and orbiter and to define orbiter plume effects on aero characteristics using solid plumes. The test was conducted at angles of attack from minus 10 deg to 30 deg and angles of sideslip of minus 10 deg thru 10 deg. Six component force data and static base pressures were recorded during the test.

Fitzgerald, F. F.↗
NASA NTRSDate not supplied

Development of a Full-Scale Finite Element Model of the Fokker F28 Fellowship Aircraft and Crash Simulation Predictions

In June 2019, a full-scale crash test of a Fokker F28 Fellowship aircraft was conducted as part of a joint National Aeronautics and Space Administration/Federal Aviation Administration (NASA/FAA) project to investigate the performance of transport aircraft under realistic crash conditions. The test objectives were to provide data for assessment of transport aircraft crashworthiness under realistic impact conditions and to generate test data for model validation. The test article was loaded with transport aircraft seats in a 3+2 configuration. A total of 24 instrumented ATDs were placed in the seats and restrained. The test article weighed 33,306-lb. (15,107.3-kg) and, during the crash test, impacted a 2-ft. (0.61-m) high soil bed at 65.3-ft/s (19.9-m/s) forward and 31.8-ft/s (9.7-m/s) vertical velocity. The full-scale aircraft crash test was simulated using the commercial nonlinear explicit transient dynamic finite element code, LS-DYNA. This paper will provide a description of the test article and the crash test conditions, document the F28 full-scale model development, and present test-analysis comparisons. The test-analysis comparisons include inertial properties, kinematic responses, structural acceleration responses, and structural deformation and failure.

Karen E Jackson↗
NASA NTRS1975

Wind tunnel tests of an 0.019-scale space shuttle integrated vehicle -2A configuration (model 14-OTS) in the NASA Ames 8 X 7 foot unitary wind tunnel, volume 2

The purpose of the test was to determine the effects of cold jet gas plumes on (1) the integrated vehicle longitudinal and lateral-directional force data, (2) exposed wing hinge moment, (3) wing pressure distributions, (4) orbiter MPS external pressure distributions, and (5) model base pressures. An investigation was undertaken to determine the similarity between solid and gaseous plumes; fluorescent oil flow visualization studies were also conducted. Plotted wing pressure data is tabulated.

Hardin, R. B.↗
NASA NTRS1976

Aerodynamic results of wind tunnel tests on a 0.010-scale model (32-QTS) space shuttle integrated vehicle in the AEDC VKF-40-inch supersonic wind tunnel (IA61)

Plotted and tabulated aerodynamic coefficient data from a wind tunnel test of the integrated space shuttle vehicle are presented. The primary test objective was to determine proximity force and moment data for the orbiter/external tank and solid rocket booster (SRB) with and without separation rockets firing for both single and dual booster runs. Data were obtained at three points (t = 0, 1.25, and 2.0 seconds) on the nominal SRB separation trajectory.

Daileda, J. J.↗
NASA NTRS2012

Material Model Evaluation of a Composite Honeycomb Energy Absorber

A study was conducted to evaluate four different material models in predicting the dynamic crushing response of solid-element-based models of a composite honeycomb energy absorber, designated the Deployable Energy Absorber (DEA). Dynamic crush tests of three DEA components were simulated using the nonlinear, explicit transient dynamic code, LS-DYNA . In addition, a full-scale crash test of an MD-500 helicopter, retrofitted with DEA blocks, was simulated. The four material models used to represent the DEA included: *MAT_CRUSHABLE_FOAM (Mat 63), *MAT_HONEYCOMB (Mat 26), *MAT_SIMPLIFIED_RUBBER/FOAM (Mat 181), and *MAT_TRANSVERSELY_ANISOTROPIC_CRUSHABLE_FOAM (Mat 142). Test-analysis calibration metrics included simple percentage error comparisons of initial peak acceleration, sustained crush stress, and peak compaction acceleration of the DEA components. In addition, the Roadside Safety Verification and Validation Program (RSVVP) was used to assess similarities and differences between the experimental and analytical curves for the full-scale crash test.

Jackson, Karen E.↗
NASA NTRS1976

Results of a landing gear loads test using a 0.0405-scale model (16-0) of the space shuttle orbiter in the Rockwell International NAAL wind tunnel (OA163), volume 1

Experimental aerodynamic investigations were conducted on a sting mounted scale representation of the 140C outer mold line space shuttle orbiter configuration in the low speed wind tunnel. The primary test objectives were to define the orbiter landing gear system pressure loading and to record landing gear door and strut hingemoment levels. Secondary objectives included recording the aerodynamic influence of various landing gear configurations on orbiter force data as well as investigating 40 x 80 ft. Ames Wind Tunnel strut simulation effects on both orbiter landing gear loads and aerodynamic characteristics. Testing was conducted at a Mach number of 0.17, free stream dynamic pressure of 42.5 PSF, and Reynolds number per unit length of 1.2 million per foot. Angle of attack variation was 0 to 20 while yaw angles ranged from -10 to 10 deg.

Mennell, R. C.↗