Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “room temperature”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 973 records · Page 54
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

High-Temperature RF Transmission Loss Characteristics of Platinum–Inconel 600 and Platinum–304 Steel Interconnects

Radio frequency (RF) transmission losses that occur at electronic interconnects is currently an important limitation of wireless sensors and other electronic device packages that must operate in high-temperature environments. Herein, in-situ RF transmission losses were measured for two types of interconnects: platinum (Pt) wire bonded to an Inconel 600 coaxial cable; and Pt-wire bonded to a block of 304 steel. Heating the Pt wire/Inconel interconnects at 800 °C for up to 200 hours were found to be very stable with no measurable transmission losses. In contrast, Pt wire/304 steel block interconnects examined over similar test periods at 800 °C exhibited gradual increases in transmission losses leveling off at 10, 38 and 85 mdB at 400 MHz, 700 MHz, and 1 GHz, respectively. Increasing the test temperature to 900 °C caused further elevated transmission losses of 30, 70 and 108 mdB at the same reported frequencies. By comparison, temperature cycling of the Pt wire/304 steel interconnects between room temperature and 900 °C was found to cause more significant degradation. In particular, four thermal cycles from room temperature to 900 °C resulted in losses of 75, 271, and 482 mdB at the same reported frequencies. Parabolic oxidation relative to the RF skin depth in the 304 steel block at the tested frequencies are discussed as possible reasons for the transmission losses during the isothermal soaks, whereas interconnect degradation due to differences in thermal expansion between Pt and 304 steel are primarily responsible for transmission losses caused by high temperature cycling.

304 steel↗
DOE OSTI2025

First-Principles Studies on Sc 2 RuZ (Z = Si, Ge, Sn) Inverse Heusler Alloys: Structural, Electronic, and Transport Properties

The continuous demand for efficient, nontoxic, and thermally stable materials for room-temperature energy conversion motivates the exploration of novel thermoelectric systems beyond the traditional magnetic Heusler alloys. While full and half-Heusler compounds, especially Co-, Ni-, and Mn-based systems, have demonstrated promising thermoelectric properties, their typically high operating temperatures and magnetic complexities limit their applicability in ambient thermal management. In this context, we investigate whether Sc-based inverse Heusler alloys can offer a viable nonmagnetic alternative with competitive thermoelectric performance. In this work, we perform a systematic first-principles study of the inverse Heusler compounds Sc 2 RuZ (Z = Si, Ge, Sn), focusing on their structural, electronic, mechanical, and thermodynamic-thermoelectric properties. Density Functional Theory (DFT) was employed to compute optimized lattice structures and band dispersion, while dynamical stability was assessed via phonon calculations. Thermoelectric transport coefficients, including Seebeck coefficient, electrical conductivity, and thermal conductivity, were estimated using the semiclassical Boltzmann transport theory within the constant relaxation time approximation. Our results show that all Sc 2 RuZ compounds are thermodynamically stable semiconductors with indirect band gaps of 0.12–0.16 eV and exhibit high elastic moduli, especially Sc 2 RuSn, which demonstrates superior stiffness and incompressibility. Importantly, all compounds display promising room-temperature thermoelectric characteristics, including high Seebeck coefficients and power factors. These findings reveal that Sc 2 RuZ alloys represent a rare class of stable, nonmagnetic inverse Heusler semiconductors with intrinsic thermoelectric potential at room temperature, unlike many existing Heusler systems optimized for spintronics or high-temperature operation. This work expands the known design space for Heusler-based thermoelectrics and offers a theoretical basis for experimental realization of efficient, low-temperature, nonmagnetic thermoelectric materials.

alloys↗
DOE OSTI2025

Defect Stability in CdTe Based on Formation Energies and Migration Barriers

Native point defects are thought to play a key role in CdTe, either as compensation centers in intentionally doped material, as a source of conductivity in nominally undoped material, or as electron–hole recombination centers. Here, the discussion of their concentration and impact has often centered only on formation energies and transition levels. Using hybrid density functional calculations, including the effects of spin–orbit coupling (SOC), we discuss the stability of native point defects in CdTe based on their formation energies and migration barriers. We show that although Cd interstitials are the lowest energy donor defects, they are unstable at room temperature due to a low migration barrier. They are important for maintaining charge neutrality during growth or annealing at high temperatures, but once the material is brought to room temperature, they are not frozen in as often assumed and are expected to anneal out, leaving the other more stable defects to determine the conductivity. Taking this into account in the solution of the charge neutrality equation, we are able to predict the conductivity type and carrier concentrations that are in good agreement with experimental observations.

14 SOLAR ENERGY↗
DOE OSTI2021

Combined experimental-theoretical study of electron mobility-limiting mechanisms in SrSnO 3

The discovery and development of ultra-wide bandgap (UWBG) semiconductors is crucial to accelerate the adoption of renewable power sources. This necessitates an UWBG semiconductor that exhibits robust doping with high carrier mobility over a wide range of carrier concentrations. Here we demonstrate that epitaxial thin films of the perovskite oxide Nd x Sr 1 – x SnO 3 (SSO) do exactly this. Nd is used as a donor to successfully modulate the carrier concentration over nearly two orders of magnitude, from 3.7 × 10 18 cm –3 to 2.0 × 10 20 cm –3 . Despite being grown on lattice-mismatched substrates and thus having relatively high structural disorder, SSO films exhibited the highest room-temperature mobility, ~70 cm 2 V –1 s –1 , among all known UWBG semiconductors in the range of carrier concentrations studied. The phonon-limited mobility is calculated from first principles and supplemented with a model to treat ionized impurity and Kondo scattering. This produces excellent agreement with experiment over a wide range of temperatures and carrier concentrations, and predicts the room-temperature phonon-limited mobility to be 76–99 cm 2 V –1 s –1 depending on carrier concentration. This work establishes a perovskite oxide as an emerging UWBG semiconductor candidate with potential for applications in power electronics

36 MATERIALS SCIENCE↗
DOE OSTI2020

Solvent selection for biphasic extraction of 5-hydroxymethylfurfural via multiscale modeling and experiments

We introduce a comprehensive conceptual framework for selecting solvents for reactive extraction in biphasic organic-water systems and demonstrate it for the separation of HMF (5-hydroxylmethylfurfural), a platform chemical produced in the acid-catalyzed dehydration of hexoses. We first perform in silico screening of ~2500 solvents, from the ADFCRS-2018 database using the ADF COSMO-RS implementation, and classification, based on the solvent partition coefficient. We then determine experimentally the partition coefficients for HMF, fructose, and products of HMF rehydration (levulinic acid (LA), and formic acid (FA)), the mutual water-organic solvent solubilities, and the separation factors in >50 select solvents spanning multiple homologous series at room temperature and a typical reaction temperature with in situ sampling. We find that COSMO-RS is excellent for screening purposes (typical error in most cases within a factor of ~2). Increased temperatures lead to significant reduction in partitioning, and room temperature measurements are clearly inadequate for solvent selection. Upon down selecting classes of solvents based on separation performance, we perform experimental thermal stability and reaction compatibility studies of a small set of solvents at relevant reactive-extraction temperatures. We discover that many substituted phenols exhibit an order-of-magnitude increase in partitioning compared to conventional solvents due chiefly to hydrogen bond interactions and show the necessary stability but retain a significant fraction of water and LA, factors that need to be considered in technoeconomic analysis. In contrast, anilines, aldehydes, and acids are good to excellent regarding separation but incompatible with this specific reaction medium. Furthermore, this multifaceted framework can be extended to other biomass-derived products and processes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Evaluation of crystalline quality of traveling heater method (THM) grown Cd0.9Zn0.1Te0.98Se0.02 crystals

Because of its excellent opto-electronic properties, CdZnTe (CZT) has been the material of choice for x- and gamma-ray detectors operable at room temperature. CZT is the leading commercially available room-temperature radiation detector material today. Although much progress has been made over the past three decades, today's CZT crystals still face certain challenges, especially the presence of the performance-limiting materials defects and the associated relatively high production cost. In this regard, CdxZn1−xTeySe1−y (CZTS) is emerging as a next-generation compound semiconductor, which overcomes some of the limitations of CZT technology for the stated applications. Here, we conducted a study to evaluate the crystalline quality of the traveling heater method grown CZTS with an optimized alloy composition, i.e., Cd0.9Zn0.1Te0.98Se0.02. The as-grown samples were evaluated by low-temperature photoluminescence (PL) spectroscopy and high-resolution x-ray diffraction using the synchrotron light source at Brookhaven National Laboratory. The full width at half maximum of both the PL and x-ray rocking curves was observed to be broadened due to the lattice disorder of the quaternary compound, eventually degrading the crystalline quality. This was consistent with density functional theory calculations.

Roy, U. N. (ORCID:0000000282089680)↗
DOE OSTI2020

The Catalytic Activity of TiO 2 Toward a Multicomponent Reaction Depends on its Morphology, Mechanoactivation and Presence of Visible Light

Aims: Test the hypothesis that the catalytic activity of TiO2 nanoparticles towards a liquidphase or mechanoactivated multicomponent reaction can be tuned by visible light and the shape of nanoparticles. Background: Catalytic multicomponent reactions have been proven to be excellent synthetic approaches to a series of biologically relevant compounds including 2-amino-4H-benzo[b]pyrans. However, the potential photocatalytic activity and structural diversity of nanostructured catalysts remained underutilized in the design of new catalytic systems. Objective: Harness the photocatalytic potential and diverse morphology of TiO2 particles as catalysts for the liquid phase and mechanoactivated multicomponent organic reactions. Results: Catalytic activity of TiO2 nanoparticles towards multicomponent synthesis of 2-amino-4Hbenzo[ b]pyrans is increased by visible light. The nanorod-shaped TiO2 nanoparticles have shown substantially higher catalytic activity towards mechanoactivated multicomponent synthesis of 2- amino-4H-benzo[b]pyrans than their spherically-shaped counterparts. Conclusion: : An efficient methodology for the synthesis of 2-amino-4H-benzo[b]pyrans under ambient light condition has been developed using TiO2 nanorods (high aspect ratio anatase nanocrystals) as photocatalyst. This simple method furnished the corresponding terahydrobenzopyrans in high yields via three component reaction of aldehyde, malononitrile, and dimidone under solvent free reaction conditions at room temperature. The reaction takes 8-10 min at room temperature under ambient light condition and the catalyst can be reused multiple times. Utilization of light and the nanorod morphology of the catalyst through mechanoactivation has been applied for the -first time to the synthetic technique of multicomponent reactions. The synthetic procedures for 2-amino-4Hbenzo[ b]pyrans have been improved.

Thirumeni, Subramanian↗
NASA NTRS1972

Carbon fiber composites for cryogenic filament-wound vessels

Advanced unidirectional and bidirectional carbon fiber/epoxy resin composites were evaluated for physical and mechanical properties over a cryogenic to room temperature range for potential application to cryogenic vessels. The results showed that Courtaulds HTS carbon fiber was the superior fiber in terms of cryogenic strength properties in epoxy composites. Of the resin systems tested in ring composites, CTBN/ERLB 4617 exhibited the highest composite strengths at cryogenic temperatures, but very low interlaminar shear strengths at room temperature. Tests of unidirectional and bidirectional composite bars showed that the Epon 828/Empol 1040 resin was better at all test temperatures. Neither fatigue cycling nor thermal shock had a significant effect on composite strengths or moduli. Thermal expansion measurements gave negative values in the fiber direction and positive values in the transverse direction of the composites.

Larsen, J. V.↗
NASA NTRS1986

Annealing of electron damage in mid-IR transmitting fluoride glass

Damage in ZrF4-BaF2-LaF3 glass induced by high-energy electrons was studied by ESR and optical spectroscopy. An optical absorption band at 314 nm in the irradiated glass annealed rapidly above about 50 C, probably by a second-order reaction at room temperature; the ESR lines annealed very slowly at room temperature.

Bansal, Narottam P.↗
NASA NTRS2007

Strain Gauges Indicate Differential-CTE-Induced Failures

A method of detecting mechanical failure induced by variation in temperature at an adhesive bond between two materials that have different coefficients of thermal expansion (CTEs) involves monitoring of strain-gauge readings. This method can be regarded as an exploitation of the prior observation that the readings of strain gauges commonly used in tensile and compressive testing of material specimens include features indicative of incremental failures in the specimens. In this method, one or more strain gauges are bonded to either or both of the two materials near the bond between the materials. (The adhesive used to bond the strain gauges would not ordinarily be the same as the one used to bond the two materials). Then strain-gauge readings are recorded as the temperature of the materials is varied through a range of interest. Any significant discontinuity in the slope of the resulting strain-versus-temperature curve(s) is taken to be a qualitative indication of a failure of the bond between the two materials and/or a failure within one of the materials in the vicinity of the bond. The method has been demonstrated in experiments on specimens consisting of polyacrylonitrile-fiber/epoxy-matrix laminated composite plates bonded by epoxy to smaller plates made, variously, of aluminum, titanium, and a low-CTE nickel/iron alloy. In preparation for each experiment, strain gauges were bonded, by use of cryogenic-rated adhesives, to the composite plate near the corners of the metal plate (see Figure 1). In each experiment, strain-gauge and temperature readings were taken as the specimen was cooled from room temperature to 20 K. The specimens were then returned to room temperature and ultrasonically inspected for damage in the bond region. No failure events were detectable in the strain-gauge readings from the composite/ titanium and composite/low-thermalexpansion- alloy specimens, and ultrasonic inspection of these specimens revealed no damage. However, failure events were seen in the strain-gauge readings from the composite/aluminum specimens (see Figure 2), and ultrasonic inspection confirmed that there was damage in the bond regions of these specimens.

Harris, Brian↗
DOE OSTI2020

Instrumentation and experimental procedures for robust collection of X-ray diffraction data from protein crystals across physiological temperatures

Traditional X-ray diffraction data collected at cryo-temperatures have delivered invaluable insights into the three-dimensional structures of proteins, providing the backbone of structure–function studies. While cryo-cooling mitigates radiation damage, cryo-temperatures can alter protein conformational ensembles and solvent structure. Furthermore, conformational ensembles underlie protein function and energetics, and recent advances in room-temperature X-ray crystallography have delivered conformational heterogeneity information that can be directly related to biological function. Given this capability, the next challenge is to develop a robust and broadly applicable method to collect single-crystal X-ray diffraction data at and above room temperature. This challenge is addressed herein. The approach described provides complete diffraction data sets with total collection times as short as ~5 s from single protein crystals, dramatically increasing the quantity of data that can be collected within allocated synchrotron beam time. Its applicability was demonstrated by collecting 1.09–1.54 Å resolution data over a temperature range of 293–363 K for proteinase K, thaumatin and lysozyme crystals at BL14-1 at the Stanford Synchrotron Radiation Lightsource. Here, the analyses presented here indicate that the diffraction data are of high quality and do not suffer from excessive dehydration or radiation damage.

36 MATERIALS SCIENCE↗
NASA NTRS1993

A method to remove intercalates from bromine and iodine intercalated carbon fibers

Upon exposure to room-temperature fluorine, intercalated carbon fibers (containing either bromine alone or iodine and bromine together) become heavier and less stable. For Amoco P-100 graphitized carbon fibers which were intercalated with 18 percent bromine by weight, 1 hr of fluorine exposure results in a large weight increase, but causes only a small decrease in thermal stability. More than l hr of fluorine exposure time results in small additional increases in fiber weight, but significant further decreases in fiber thermal stability. Such phenomena do not occur if the fluorine exposure is at 250 C. These observations suggest the mechanism that at room temperature, fluorine is absorbed quickly by the intercalated fibers and intercalated slowly into the fibers. Most of the original intercalates are replaced by fluorine in the process of fluorine intercalation. Under an inert environment, the bromine intercalated fibers are much more thermally stable. After 800 C vacuum heating for two weeks, the brominated fibers lost about 45 percent of their bromine, and their resistivity increased from 64 omega-cm to a range of 95 to 170 micro omega-cm. This is still much lower than the 300 micro omega-cm value for pristine P-100. For practical purposes, in order to preserve their thermal stability, brominated fibers need to be protected from exposure to fluorine at room temperature, or to any intercalate at a temperature where, upon direct contact to graphite, an intercalation compound can easily be formed.

Hung, Ching-Cheh↗
DOE OSTI2020

Structural and Thermoelectric Properties of Black Arsenic–Phosphorus

Here, we report the structural and temperature dependent transport properties of As x P 1-x (x = 0, 0.2, 0.5, 0.83, 1) alloys. It is observed that black phosphorous (BP)-related phonon modes in the alloy samples are red-shifted with increasing arsenic concentration, while black arsenic-related modes in these samples are blue-shifted with increasing phosphorus concertation. As the arsenic concentration, x increases from 0 to 1, the 4-probe resistance of the As x P 1-x alloys is found to decrease by more than 3 orders of magnitude. The transport studies reveal that samples with the highest arsenic concentration (x = 1 and 0.83) show metallic behavior in the temperature dependence of resistance with a small thermopower at room temperature with an anomalous temperature dependence. In contrast, the samples with high phosphorus concentration (x = 0, 0.2, and 0.5) show very large thermopower values at room temperature reaching a value as high as 803 μV/k for x = 0.2. The temperature dependence of the thermopower of these samples can be well described by the variable range hopping (VRH) mechanism in two-dimensions (2-d), S ~ T 1/3 . Similarly, their 4-probe resistance (R) values can be fitted with 2-d VRH mechanism, R ~ exp(T -1/3 ).

36 MATERIALS SCIENCE↗
NASA NTRS2017

Mechanism of Supercooled Water Droplet Breakup near the Leading Edge of an Airfoil

This work presents the results of an experimental study on supercooled droplet deformation and breakup near the leading edge of an airfoil. The results are compared to prior room temperature droplet deformation results to explore the effects of droplet supercooling. The experiments were conducted in the Adverse Environment Rotor Test Stand (AERTS) at The Pennsylvania State University. An airfoil model placed at the end of the rotor blades mounted onto the hub in the AERTS chamber was moved at speeds ranging between 50 and 80 m/sec. The temperature of the chamber was set at -20˚C. A monotonic droplet generator was used to produce droplets that fell from above, perpendicular to the path of the airfoil. The supercooled state of the droplets was determined by measurement of the temperature of the drops at various locations below the droplet generator exit. A temperature prediction code was also used to estimate the temperature of the droplets based on vertical velocity and the distance traveled by droplets from the droplet generator to the airfoil stagnation line. High speed imaging was employed to observe the interaction between the droplets and the airfoil. The high speed imaging provided droplet deformation information as the droplet approached the airfoil near the stagnation line. A tracking software program was used to measure the horizontal and vertical displacement of the droplet against time. It was demonstrated that to compare the effects of water supercooling on droplet deformation, the ratio of the slip velocity and the initial droplet velocity must be equal. A case with equal slip velocity to initial velocity ratios was selected for room temperature and supercooled droplet conditions. The airfoil velocity was 60 m/s and the slip velocity for both sets of data was 40 m/s. In these cases, the deformation of the weakly supercooled and warm droplets did not present different trends. The similar behavior for both environmental conditions indicates that water supercooling has no effect on particle deformation for the limited range of the weak supercooling of the droplets tested and the selected impact velocity. The assumption of a constant surface tension value was further supported by the equal trend of the Bond number obtained for supercooled and room temperature droplets.

in-flight icing↗
NASA NTRS2011

Sub-Shot Noise Power Source for Microelectronics

Low-current, high-impedance microelectronic devices can be affected by electric current shot noise more than they are affected by Nyquist noise, even at room temperature. An approach to implementing a sub-shot noise current source for powering such devices is based on direct conversion of amplitude-squeezed light to photocurrent. The phenomenon of optical squeezing allows for the optical measurements below the fundamental shot noise limit, which would be impossible in the domain of classical optics. This becomes possible by affecting the statistical properties of photons in an optical mode, which can be considered as a case of information encoding. Once encoded, the information describing the photon (or any other elementary excitations) statistics can be also transmitted. In fact, it is such information transduction from optics to an electronics circuit, via photoelectric effect, that has allowed the observation of the optical squeezing. It is very difficult, if not technically impossible, to directly measure the statistical distribution of optical photons except at extremely low light level. The photoelectric current, on the other hand, can be easily analyzed using RF spectrum analyzers. Once it was observed that the photocurrent noise generated by a tested light source in question is below the shot noise limit (e.g. produced by a coherent light beam), it was concluded that the light source in question possess the property of amplitude squeezing. The main novelty of this technology is to turn this well-known information transduction approach around. Instead of studying the statistical property of an optical mode by measuring the photoelectron statistics, an amplitude-squeezed light source and a high-efficiency linear photodiode are used to generate photocurrent with sub-Poissonian electron statistics. By powering microelectronic devices with this current source, their performance can be improved, especially their noise parameters. Therefore, a room-temperature sub-shot noise current source can be built that will be beneficial for a very broad range of low-power, low-noise electronic instruments and applications, both cryogenic and room-temperature. Taking advantage of recent demonstrations of the squeezed light sources based on optical micro-disks, this sub-shot noise current source can be made compatible with the size/power requirements specific of the electronic devices it will support.

Strekalov, Dmitry V.↗
NASA NTRS1992

Carbon/Carbon Fasteners For Use At High Temperatures

Fasteners made of advanced carbon/carbon material perform well at ambient and high temperatures. Exhibit shear strengths of more than 10 kpsi at room temperature and 13 kpsi at temperature of 2,700 degrees F. However, fasteners exhibited poor tensile strength at room temperature. Best suited to applications in which exposed to shear loads with minimal tension loads. Parts reused after thermal cycling.

Bohlmann, Frank J.↗
NASA NTRS2006

Chemical, Physical, and Mechanical Characterization of Isocyanate Cross-linked Amine-Modified Silica Aerogels

We describe a new mechanically strong lightweight porous composite material obtained by encapsulating the skeletal framework of amine-modified silica aerogels with polyurea. The conformal polymer coating preserves the mesoporous structure of the underlying silica framework and the thermal conductivity remains low at 0.041 plus or minus 0.001 W m(sup -1 K(sup -1). The potential of the new cross-linked silica aerogels for load-carrying applications was determined through characterization of their mechanical behavior under compression, three-point bending, and dynamic mechanical analysis (DMA). A primary glass transition temperature of 130 C was identified through DMA. At room temperature, results indicate a hyperfoam behavior where in compression cross-linked aerogels are linearly elastic under small strains (less than 4%) and then exhibit yield behavior (until 40% strain), followed by densification and inelastic hardening. At room temperature the compressive Young's modulus and the Poisson's ratio were determined to be 129 plus or minus 8 MPa and 0.18, respectively, while the strain at ultimate failure is 77% and the average specific compressive stress at ultimate failure is 3.89 x 10(exp 5) N m kg(sup -1). The specific flexural strength is 2.16 x 10(exp 4) N m kg(sup -1). Effects on the compressive behavior of strain rate and low temperature were also evaluated.

Katti, Atul↗