Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “polymer films”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 973 records · Page 54
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

Evaluations of candidate encapsulation designs and materials for low-cost silicon photovoltaic arrays

Three encapsulation designs for silicon photovoltaic arrays based on cells with silk-screened Ag metallization have been evaluated: transparent polymeric coatings over cells laminated between two films or sheets of polymeric materials; cells adhesively bonded to a glass cover with a polymer pottant and a glass or other substrate component. Silicone and acrylic coatings were assessed, together with acrylic sheet, 0.635 mm fiberglass-reinforced polyester sheet, 0.102 mm polycarbonate/acrylic dual-layer film, 0.127 mm fluorocarbon film, soda-lime glass, borosilicate glass, low-iron glass, and several adhesives. The encapsulation materials were characterized by light transmittance measurements, determination of moisture barrier properties and bond strengths, and by the performance of cells before and after encapsulation. Silicon and acrylic coatings provided inadequate protection. Acrylic and fluorocarbon films displayed good weatherability and acceptable optical transmittance. Borosilicate, low-iron and soda-lime-float glasses were found to be acceptable candidate encapsulants for most environments.

Gaines, G. B.↗
NASA NTRS1975

Fabrication and evaluation of polymeric early-warning fire-alarm devices

The electrical resistivities were investigated of some polymers known to be enhanced by the presence of certain gases. This was done to make a device capable of providing early warning to fire through its response with the gases produced in the early phases of combustion. Eight polymers were investigated: poly(phenyl acetylene), poly(p-aminophenyl acetylene), poly(p-nitrophenyl acetylene), poly(p-formamidophenyl acetylene), poly(ethynyl ferrocene), poly(ethynyl carborane), poly(ethynyl pyridine), and the polymer made from 1,2,3,6 tetramethyl pyridazine. A total of 40 usable thin-film sandwich devices and a total of 70 usable interdigitated-electrode lock-and-key devices were fabricated. The sandwich devices were used for measurements of contact linearity, polymer conductivity, and polymer dielectric constant. The lock-and-key devices were used to determine the response of the polymers to a spectrum of gases that included ammonia, carbon nonoxide, carbon dioxide, sulfur dioxide, ethylene, acrolein, water vapor, and normal laboratory air. Strongest responses were to water vapor, ammonia, and acrolein, and depending on the polymer, weaker responses to carbon dioxide, sulfur dioxide, and carbon monoxide were observed. A quantitative theory of device operation, capable of accounting for observed device leakage current and sensitivity, was developed. A prototype detection/alarm system was designed and built for use in demonstrating sensor performance.

Senturia, S. D.↗
NASA NTRS1992

Chemistry and properties of poly(arylene ether benzoxazole)s

Several new poly(arylene ether benzoxazole)s (PAEBs) were prepared by the nucleophilic displacement reaction of activated aromatic difluorides with two novel bis(hydroxyphenyl benzoxazole), using potassium carbonate. The 6F-containing PAEBs exhibited better solubility and higher Tgs than did the 6,6'-bis-(2-(4-hydroxyphenyl)benzoxazole)-derived polymers. Several of the 6,6'bis(2-(4-hydroxyphenyl)benzoxazole)-derived polymers exhibited crystallinity by DSC and wide-angle X-ray diffraction. Unorientated thin film properties of the 6F-containing PAEBs were comparable to those of other 6F-containing PAEBS that were previously reported. The chemistry and the physical and mechanical properties of the above polymers are discussed.

Smith, J. G., Jr.↗
NASA NTRS2008

All-Organic Actuator Fabricated with Single Wall Carbon Nanotube Electrodes

Compliant electrodes to replace conventional metal electrodes have been required for many actuators to relieve the constraint on the electroactive layer. Many conducting polymers have been proposed for the alternative electrodes, but they still have a problem of poor thermal stability. This article reports a novel all-organic actuator with single wall carbon nanotube (SWCNT) films as the alternative electrode. The SWCNT film was obtained by filtering a SWCNT solution through an anodized alumina membrane. The conductivity of the SWCNT film was about 280 S/cm. The performance of the SWCNT film electrode was characterized by measuring the dielectric properties of NASA Langley Research Center - Electroactive Polymer (LaRC-EAP) sandwiched by the SWCNT electrodes over a broad range of temperature (from 25 C to 280 C) and frequency (from 1 KHz to 1 MHz). The all-organic actuator with the SWCNT electrodes showed a larger electric field-induced strain than that with metal electrodes, under identical measurement conditions.

Lowther, Sharon E.↗
NASA NTRS1995

Gas Sensor Test Chip

A new test chip is being developed to characterize conducting polymers used in gas sensors. The chip, a seven-layer cofired alumina substrate with gold electrodes, contains 11 comb and U- bend test structures. These structures are designed to measure the sheet resistance, conduction anisotropy, and peripheral conduction of spin-coated films that are not subsequently patterned.

conducting polymers gas sensors test chipnd periph↗
NASA NTRS1998

Synthesis of Polymers Containing Covalently Bonded NLO Chromophores

Polymers containing covalently bonded nonlinear optical (NLO) chromophores are expected to possess special properties such as greater stability, better mechanical processing, and easier film formation than their non-polymeric equivalent. For the present work, polymethylmethacrylate (PMMA) was selected as the basic polymer unit on which to incorporate different NLO chromophores. The NLO components were variations of DIVA {[2-methoxyphenyl methylidene]-propanedinitrile} which we prepared from vanillin derivatives and malononitrile. These were esterified with methacrylic acid and polymerized either directly or with methyl methacrylate to form homopolymers or copolymers respectively. Characterization of the polymers and NLO property studies are underway.

Denga, Xiao-Hua↗
DOE OSTI2023

19.32% Efficiency Polymer Solar Cells Enabled by Fine-Tuning Stacking Modes of Y-Type Molecule Acceptors: Synergistic Bromine and Fluorine Substitution of the End Groups

Here, the success of Y6-type nonfullerene small molecule acceptors (NF-SMAs) in polymer solar cells (PSCs) can be attributed to their unique honeycomb stacking style, which leads to favorable thin-film morphologies. The intermolecular interactions related to the crystallization tendency of these NF-SMAs is closely governed by their electron accepting end groups. For example, the high performance Y6 derivative L8-BO (BTP-4F) presents three types of stacking modes in contrast to two stacking modes of Y6. Hence, it is ultimately interesting to obtain more insight on the packing properties and the preferences influenced by chemical modifications such as end group engineering. This work designs and synthesizes asymmetric and symmetric L8-BO derivatives with brominated end groups and explores the stacking preferences in various modes. The asymmetric BTP-3FBr displays an optimized crystallization tendency and thin film morphology, leading to a decent power conversion efficiency (PCE) of 18.34% in binary devices and a top PCE of 19.32% in ternary devices containing 15 wt% IDIC as the second acceptor.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Role of Bottlebrush Additives on the Structure of Block Copolymers in the Bulk and Thin Films

Blending block copolymers (BCP) with additives is a useful approach for controlling BCP morphology and properties. In athermal systems, blends of BCPs with polymer additives having very high molecular (M n ) mass generally result in macrophase separation. Bottlebrush polymers, which consist of a linear backbone and grafted side chains, present an interesting alternative where the overall M n of the system can be very large but the low M n side chains may drive miscibility with the BCP. Here, in this study, a bottlebrush with a polynorbornene backbone and polystyrene (PS) side chains is blended with PS-b-poly(methyl methacrylate) (PS-b-PMMA) of varying M n , and the resulting morphologies are examined in both the bulk and thin films. Two different M n of PS-b-PMMA were used in the bulk study, and the analysis of small-angle X-ray scattering data shows that the blends were miscible and lamellar at all concentrations. This deviates from reference series of both low and high M n linear polymer additives, which either showed morphological transitions from lamellae to cylinders (low M n ) or were immiscible at all mass fractions studied (high M n ). The relative molecular mass of the side chain (N SC ) and the corresponding component in the BCP (N A ) dictate the distribution of the bottlebrush throughout the BCP, analogous to BCP/linear blends or grafted nanoparticles in a homopolymer matrix. The studies on thin films show a thickness dependence for bottlebrush mass fractions at or above 0.17, a behavior which may be driven by conformational changes of the bottlebrush upon confinement.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Polymer-assisted deposition of nanoparticle feedstocks for target fabrication

Traditional polymer-assisted deposition has been shown to produce highly uniform thin films of metal oxides, including actinide oxides. Furthermore, while producing thicker films for nuclear targets is possible through repeated coating application, we exchanged the dissolved metal species with nanoparticles to maximize the thickness that can be achieved with an individual layer. Using CeO 2 nanoparticles in a polyethyleneimine matrix, we produced targets with single-layer areal densities of 0.22 ± 0.01 mg·cm −2 (1σ) and thicknesses of 690 ± 80 nm (1σ). A custom 3D-printed spin coating chuck attachment with an inlay improved target homogeneity and will streamline future work with radioactive materials.

and nuclear chemistry↗
NASA NTRS1998

Development of Polyimides-Based NLO Materials for Electrooptical Applications

Development of thermally stable optical materials for nonlinear optics have recently focused on the covalent incorporation of NLO chromophores into high performance polymers, especially thermally stable and processable polyamides. One key aspect for the incorporation of robust NLO chromophores into high Tg polymers is to sustain poling induced order. Other advantages include high loading level of chromophores, and elimination of possible phase separation as well as chromophore sublimation at processing or working temperature. We have prepared several polyimide based polymers which are covalently linked with thermally stable chromophores that we have developed, since polyamides generally exhibit high Tg and good film transparency. Here, we report the development and subsequent incorporation of indoline based chromophores into polyamides, leading to thermally stable NLO polymers.

Rutherford, Jacqueline↗
NASA NTRS2001

Thin-Film Organic-Based Solar Cells for Space Power

Recent advances in dye-sensitized and organic polymer solar cells have lead NASA to investigate the potential of these devices for space power generation. Dye-sensitaized solar cells were exposed to simulated low-earth orbit conditions and their performance evaluated. All cells were characterized under simulated air mass zero (AM0) illumination. Complete cells were exposed to pressures less than 1 x 10 (exp -7)torr for over a month, with no sign of sealant failure or electrolyte leakage. Cells from Solaronix SA were rapid thermal cycled under simulated low-earth orbit conditions. The cells were cycled 100 times from -80 C to 80 C, which is equivalent to 6 days in orbit. The best cell had a 4.6% loss in efficiency as a result of the thermal cycling. In a separate project, novel -Bridge-Donor-Bridge-Acceptor- (-BDBA-) type conjugated block copolymer systems have been synthesized and characterized by photoluminescence (PL). In comparison to pristine donor or acceptor, the PL emissions of final -B-D-B-A- block copolymer films were quenched over 99%. Effective and efficient photo induced electron transfer and charge separation occurs due to the interfaces of micro phase separated donor and acceptor blocks. The system is very promising for a variety high efficiency light harvesting applications. Under an SBIR contract, fullerene-doped polymer-based photovoltaic devices were fabricated and characterized. The best devices showed overall power efficiencies of approximately 0.14% under white light. Devices fabricated from 2% solids content solutions in chlorobenzene gave the best results. Presently, device lifetimes are too short to be practical for space applications.

Bailey, Sheila G.↗
NASA NTRS2002

Thin-film Organic-based Solar Cells for Space Power

Recent advances in dye-sensitized and organic polymer solar cells have lead NASA to investigate the potential of these devices for space power generation. Dye-sensitized solar cells were exposed to simulated low-earth orbit conditions and their performance evaluated. All cells were characterized under simulated air mass zero (AM0) illumination. Complete cells were exposed to pressures less than 1 x 10(exp -7) torr for over a month, with no sign of sealant failure or electrolyte leakage. Cells from Solaronix SA were rapid thermal cycled under simulated low-earth orbit conditions. The cells were cycled 100 times from -80 C to 80 C, which is equivalent to 6 days in orbit. The best cell had a 4.6 percent loss in efficiency as a result of the thermal cycling. In a separate project, novel -Bridge-Donor-Bridge- Acceptor- (-BDBA-) type conjugated block copolymer systems have been synthesized and characterized by photoluminescence (PL). In comparison to pristine donor or acceptor, the PL emissions of final -B-D-B-A- block copolymer films were quenched over 99 percent. Effective and efficient photo induced electron transfer and charge separation occurs due to the interfaces of micro phase separated donor and acceptor blocks. The system is very promising for a variety high efficiency light harvesting applications. Under an SBIR contract, fullerene-doped polymer-based photovoltaic devices were fabricated and characterized. The best devices showed overall power efficiencies of approx. 0.14 percent under white light. Devices fabricated from 2 percent solids content solutions in chlorobenzene gave the best results. Presently, device lifetimes are too short to be practical for space applications.

Bailey, Sheila G.↗
NASA NTRS1978

Ion beam sputtering of fluoropolymers

Ion beam sputter processing rates as well as pertinent characteristics of etched targets and films are described. An argon ion beam source was used to sputter etch and deposit the fluoropolymers PTFE, FEP, and CTFE. Ion beam energy, current density, and target temperature were varied to examine effects on etch and deposition rates. The ion etched fluoropolymers yield cone or spire-like surface structures which vary depending upon the type of polymer, ion beam power density, etch time, and target temperature. Sputter target and film characteristics documented by spectral transmittance measurements, X-ray diffraction, ESCA, and SEM photomicrographs are included.

Sovey, J. S.↗
NASA NTRS1993

Micro-opto-mechanical devices and systems using epitaxial lift off

The integration of high quality, single crystal thin film gallium arsenide (GaAs) and indium phosphide (InP) based photonic and electronic materials and devices with host microstructures fabricated from materials such as silicon (Si), glass, and polymers will enable the fabrication of the next generation of micro-opto-mechanical systems (MOMS) and optoelectronic integrated circuits. Thin film semiconductor devices deposited onto arbitrary host substrates and structures create hybrid (more than one material) near-monolithic integrated systems which can be interconnected electrically using standard inexpensive microfabrication techniques such as vacuum metallization and photolithography. These integrated systems take advantage of the optical and electronic properties of compound semiconductor devices while still using host substrate materials such as silicon, polysilicon, glass and polymers in the microstructures. This type of materials optimization for specific tasks creates higher performance systems than those systems which must use trade-offs in device performance to integrate all of the function in a single material system. The low weight of these thin film devices also makes them attractive for integration with micromechanical devices which may have difficulty supporting and translating the full weight of a standard device. These thin film devices and integrated systems will be attractive for applications, however, only when the development of low cost, high yield fabrication and integration techniques makes their use economically feasible. In this paper, we discuss methods for alignment, selective deposition, and interconnection of thin film epitaxial GaAs and InP based devices onto host substrates and host microstructures.

Camperi-Ginestet, C.↗
NASA NTRS2002

Fabrication and Electromagnetic Characterization of Novel Self-Metallized Thin Films

Unique, self-metallized films were investigated for deployable reflector antenna applications at L-band. Polyamic acid resins or soluble polyimides were doped with metal complexes, cast into films, and thermally cured. Each resulting film had a metallic layer on one side, adhering unfailingly to the polymer. Metallization was successful for silver or palladium in 3,3',4,4'-benzophenonetetracarboxylic acid dianhydride (BTDA) and 4,4'- oxydianiline and for gold in BTDA and 2,2-bis[4-(4- aminophenoxy)phenyl]hexafluoropropane (4-BDAF) or the space durable polyimide, 2,2-bis(3,4-dicarboxyphenyl)- hexafluoropropane dianhydride and 4-BDAF (LaRCCP1). Reflectivity, transmissivity, and emissivity were determined, using an HP 8510 Vector Network Analyzer, to within 0.001 precision and accuracy. A custom-made test fixture/positioner, a thru-reflect-line calibration, and calculated reflection coefficients were used. The Ag film proved most suitable for further study, with 0.9957 reflectivity and 0.0042 emissivity. The Pd films were 0.89 reflective and 0.11 emissive; both Au films tested entirely transmissive. Transmission and scanning electron micrographs, S-parameters, and power coefficients are shown.

Mackenzie, Anne I.↗
DOE OSTI2023

Effect of Molecular Weight on the Morphology of a Polymer Semiconductor–Thermoplastic Elastomer Blend

Abstract Polymer semiconductors (PSCs) are essential active materials in mechanically stretchable electronic devices. However, many exhibit low fracture strain due to their rigid chain conformation and the presence of large crystalline domains. Here, a PSC/elastomer blend, poly[((2,6‐bis(thiophen‐2‐yl)‐3,7‐bis(9‐octylnonadecyl)thieno[3,2‐b]thieno[2′,3′:4,5]thieno[2,3‐d]thiophene)‐5,5′‐diyl)(2,5‐bis(8‐octyloctadecyl)‐3,6‐di(thiophen‐2‐yl)pyrrolo[3,4‐c]pyrrole‐1,4‐dione)‐5,5′‐diyl]] (P2TDPP2TFT4) and polystyrene‐ block ‐poly(ethylene‐ran‐butylene)‐ block ‐polystyrene (SEBS) are systematically investigated. Specifically, the effects of molecular weight of both SEBS and P2TDPP2TFT4 on the resulting blend morphology, mechanical, and electrical properties are explored. In addition to commonly used techniques, atomic force microscopy‐based nanomechanical images are used to provide additional insights into the blend film morphology. Opposing trends in SEBS‐induced aggregation are observed for the different P2TDPP2TFT4 molecular weights upon increasing the SEBS molecular weight from 87 to 276 kDa. Furthermore, these trends are seen in device performance trends for both molecular weights of P2TDPP2TFT4. SEBS molecular weight also has a substantial influence on the mesoscale phase separation. Strain at fracture increases dramatically upon blending, reaching a maximum value of 640% ± 20% in the blended films measured with film‐on‐water method. These results highlight the importance of molecular weight for electronic devices. In addition, this study provides valuable insights into appropriate polymer selections for stretchable semiconducting thin films that simultaneously possess excellent mechanical and electrical properties.

36 MATERIALS SCIENCE↗
DOE OSTI2020

X-ray photoelectron spectroscopy and rotating disk electrode measurements of smooth sputtered Fe-N-C films

Electrocatalysts for the oxygen reduction reaction (ORR) based on complexes of iron and nitrogen in a carbon matrix (Fe-N-C) are a promising alternative to platinum group metal (PGM) based catalysts in polymer electrolyte membrane (PEM) fuel cells. Further improvements of Fe-N-C catalysts would benefit from model thin film studies of activity and stability of catalytic sites, but synthesis of Fe-N-C model thin films is challenging. Here we report on synthesis and characterization of Fe-N-C thin films produced by co-sputtering iron and carbon in a reactive nitrogen atmosphere onto removable glassy carbon rotating disk electrode (RDE) tips. Scanning electron microscopy (SEM) measurements indicate that the Fe-N-C films deposited at high temperature are smoother than the films annealed at high temperature. Electrocatalytic activity measured on the thin Fe-N-C films is greater for both high-temperature samples than for the room-temperature sample. From the analysis of X-ray photoelectron spectroscopy (XPS) data, exposure of the films to high temperatures results in increased graphitization of the carbon with the Fe-N-C films, and increased relative amount of graphitic and hydrogenated nitrogen species. Overall the results of this study demonstrate the feasibility of a thin film model system approach for studying active sites in PGM-free catalysts.

14 SOLAR ENERGY↗
DOE OSTI2025

Polaron Delocalization and Transport in Doped Graphene Nanoribbon Thin Films

Graphene nanoribbons (GNRs) are quantum-confined π-conjugated monolayer semiconductors with attractive properties for optoelectronic applications. However, the ground- and excited-state properties of charge carriers in GNRs are still poorly understood, particularly with regards to the coupling between charges and the GNR lattice and the degree to which this coupling impacts local and macroscopic charge transport. To address this issue, we systematically correlate carrier density-dependent charge transport with spectroscopic modulations in chemically doped thin films of armchair graphene nanoribbons (9-aGNRs). This study combines Fourier transform infrared (FTIR) and ultraviolet−visible−near-infrared (UV−vis−NIR) spectroscopy with both local and macroscopic conductivity measurements to arrive at a full and self-consistent picture of transport in doped GNR thin films. Using three different molecular p-type dopants (i.e., oxidants), we demonstrate that hole polarons are the dominant quasi-particle determining charge transport in GNRs and that the degree of polaron delocalization depends sensitively on the dopant and the hole density. For all three dopants, the local conductivity probed by microwave spectroscopy substantially exceeds the long-range conductivity obtained by four-point probe measurements. Interestingly, the dopant size substantially influences charge transport at high hole densities. We ascribe this effect to different propensities for forming bipolarons with lower mobilities than polarons. Comparison of GNR transport and spectral properties to other prototypical π-conjugated semiconductors (e.g., semiconducting polymers or carbon nanotubes) benchmark the charge transport properties of GNR thin films for optoelectronic devices and applications.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗