Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “phase transformations”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 973 records · Page 54
All sourcesNASA NTRSDOE OSTI
NASA NTRS2015

On the Recovery Stress of a Ni50.3Ti29.7Hf20 High Temperature Shape Memory Alloy

Recovery stress in shape memory alloys (SMAs), also known as blocking stress, is an important property generally obtained during heating under a dimensional constraint as the material undergoes the martensitic phase transformation. This property has been instinctively utilized in most SMA shape-setting procedures, and has been used in numerous applications such as fastening and joining, rock splitting, safety release mechanisms, reinforced composites, medical devices, and many other applications. The stress generation is also relevant to actuator applications where jamming loads (e.g., in case the actuator gets stuck and is impeded from moving) need to be determined for proper hardware sizing. Recovery stresses in many SMA systems have been shown to reach stresses in the order of 800 MPa, achieved via thermo-mechanical training such as pre-straining, heat treatments or other factors. With the advent of high strength, high temperature SMAs, recovery stress data has been rarely probed, and there is no information pertinent to the magnitudes of these stresses. Thus, the purpose of this work is to investigate the recovery stress capability of a precipitation strengthened, Ni50.3Ti29.7Hf20 (at.) high temperature SMA in uniaxial tension and compression. This material has been shown to exhibit outstanding strength and stability during constant-stress, thermal cycling, but no data exists on constant-strain thermal cycling. Several training routines were implemented as part of this work including isothermal pre-straining, isobaric thermal cycling, and isothermal cyclic training routines. Regardless of the training method used, the recovery stress was characterized using constant-strain (strain-controlled condition) thermal cycling between the upper and lower cycle temperatures. Preliminary results indicate recovery stresses in excess of 1.5 GPa were obtained after a specific training routine. This stress magnitude is significantly higher than conventional NiTi stress generation capability.

Recovery Stress↗
NASA NTRS2016

Recommended Maximum Temperature For Mars Returned Samples

The Returned Sample Science Board (RSSB) was established in 2015 by NASA to provide expertise from the planetary sample community to the Mars 2020 Project. The RSSB's first task was to address the effect of heating during acquisition and storage of samples on scientific investigations that could be expected to be conducted if the samples are returned to Earth. Sample heating may cause changes that could ad-versely affect scientific investigations. Previous studies of temperature requirements for returned mar-tian samples fall within a wide range (-73 to 50 degrees Centigrade) and, for mission concepts that have a life detection component, the recommended threshold was less than or equal to -20 degrees Centigrade. The RSSB was asked by the Mars 2020 project to determine whether or not a temperature requirement was needed within the range of 30 to 70 degrees Centigrade. There are eight expected temperature regimes to which the samples could be exposed, from the moment that they are drilled until they are placed into a temperature-controlled environment on Earth. Two of those - heating during sample acquisition (drilling) and heating while cached on the Martian surface - potentially subject samples to the highest temperatures. The RSSB focused on the upper temperature limit that Mars samples should be allowed to reach. We considered 11 scientific investigations where thermal excursions may have an adverse effect on the science outcome. Those are: (T-1) organic geochemistry, (T-2) stable isotope geochemistry, (T-3) prevention of mineral hydration/dehydration and phase transformation, (T-4) retention of water, (T-5) characterization of amorphous materials, (T-6) putative Martian organisms, (T-7) oxidation/reduction reactions, (T-8) (sup 4) He thermochronometry, (T-9) radiometric dating using fission, cosmic-ray or solar-flare tracks, (T-10) analyses of trapped gasses, and (T-11) magnetic studies.

Beaty, D. W.↗
NASA NTRS2016

Parallel Grand Canonical Monte Carlo (ParaGrandMC) Simulation Code

This report provides an overview of the Parallel Grand Canonical Monte Carlo (ParaGrandMC) simulation code. This is a highly scalable parallel FORTRAN code for simulating the thermodynamic evolution of metal alloy systems at the atomic level, and predicting the thermodynamic state, phase diagram, chemical composition and mechanical properties. The code is designed to simulate multi-component alloy systems, predict solid-state phase transformations such as austenite-martensite transformations, precipitate formation, recrystallization, capillary effects at interfaces, surface absorption, etc., which can aid the design of novel metallic alloys. While the software is mainly tailored for modeling metal alloys, it can also be used for other types of solid-state systems, and to some degree for liquid or gaseous systems, including multiphase systems forming solid-liquid-gas interfaces.

Vesselin I Yamakov↗
NASA NTRS2016

Ab Initio Simulations of Temperature Dependent Phase Stability and Martensitic Transitions in NiTi

For NiTi based alloys, the shape memory effect is governed by a transition from a low-temperature martensite phase to a high-temperature austenite phase. Despite considerable experimental and computational work, basic questions regarding the stability of the phases and the martensitic phase transition remain unclear even for the simple case of binary, equiatomic NiTi. We perform ab initio molecular dynamics simulations to describe the temperature-dependent behavior of NiTi and resolve several of these outstanding issues. Structural correlation functions and finite temperature phonon spectra are evaluated to determine phase stability. In particular, we show that finite temperature, entropic effects stabilize the experimentally observed martensite (B19') and austenite (B2) phases while destabilizing the theoretically predicted (B33) phase. Free energy computations based on ab initio thermodynamic integration confirm these results and permit estimates of the transition temperature between the phases. In addition to the martensitic phase transition, we predict a new transition between the B33 and B19' phases. The role of defects in suppressing these phase transformations is discussed.

nickel titanium↗
NASA NTRS2016

Ab Initio Simulations of Phase Stability and Martensitic Transitions in NiTi

For NiTi based alloys, the shape memory effect is governed by a transition from a low-temperature martensite phase to a high-temperature austenite phase. Despite considerable experimental and computational work, basic questions regarding the stability of the phases and the martensitic phase transition remain unclear even for the simple case of binary, equiatomic NiTi. We perform ab initio molecular dynamics simulations to describe the temperature-dependent behavior of NiTi and resolve several of these outstanding issues. Structural correlation functions and finite temperature phonon spectra are evaluated to determine phase stability. We show that finite temperature, entropic effects stabilize the experimentally observed martensite (B19') and austenite (B2) phases while destabilizing the theoretically predicted (B33) phase. Free energy computations based on ab initio thermodynamic integration confirm these results and permit estimates of the transition temperature between the phases. In addition to the martensitic phase transition, we predict a new transition between the B33 and B19' phases. The role of defects in suppressing phase transformation temperatures is discussed.

Simulations↗
NASA NTRS2020

Producing Next Generation Superalloys Through Advanced Characterization and Manufacturing Techniques

NASA is currently working towards developing the next generation high temperature alloys for various aerospace and energy applications. Through advanced microscopy and computational insights, a novel atomic scale strengthening mechanism was discovered in Ni-base superalloys. This new local phase transformation strengthening technique has been successfully implemented resulting in new disk alloys with substantial improvements in creep strength over current state-of-the-art. Furthermore, additive manufacturing has been leveraged to produce dispersion strengthened (DS), multi-principal element alloys (MPEA) without the use of traditional mechanical alloying or chemical reactions. This new processing technique has successfully resulted in 99.9% dense oxide dispersion strengthened NiCoCr alloy parts. High temperature mechanical testing of the DS alloys showed significant improvements in strength and ductility over the baseline NiCoCr. As a result, this recently discovered processing route opens a new alloy design and production path that is synergistic between additive manufacturing and dispersion strengthening, possibly enabling a new generation of high-performance alloys.

Smith, Timothy M.↗
NASA NTRSDate not supplied

TPSAS-NF1676L-17800-DND

Currently, there are two national challenge problems that guide much of the research in durability and damage tolerance at NASA Langley. The first, Airframe Digital Twin, is a concept that combines as-built vehicle components, as-experienced loads and environments, and other vehicle-specific characteristics to enable ultrahigh fidelity modeling of aircraft and spacecraft throughout their service lives. The second, Materials Genome Initiative, is an analog to the Human Genome Project, and is intended to improve the rate at which materials scientists can discover, understand fundamental physics, and improve material systems. This presentation will highlight several research projects ongoing at NASA Langley that are in support of the above challenge problems. Two of those topics will be the subject of detailed discussion. First, investigations of microstructurally-small fatigue cracking (MSFC) in Al-2Cu and Al-4Cu, fabricated in-house, will be presented. Single- and oligo-crystals of Al-Cu specimens were loaded in uniaxial fatigue, while high-resolution in-situ measurements of deformation were made using image correlation (IC) in a scanning-electron microscope (SEM). The Al-Cu specimens were then replicated as crystal plasticity finite element models (CPFEM), where evolution of slip localization near grain boundaries was computed. Comparison among experiment and CPFEM is made. In addition, XRay diffraction measurements of the as-fabricated specimens were carried out, where direct measurements of the embedded copper precipitates were made, and their influence on growing MSFCs were directly observed. The second main topic will illustrate ongoing work in the area of so-called damage-sensing particles. In this work, shape-memory alloys are embedded in an aluminum alloy matrix. Upon the propagation of a fatigue crack, these particles undergo a strain-induced phase transformation which is detected using an acoustic sensor, providing real-time information on propagating cracks. Experiments and simulations regarding the development of this system will also be detailed.

Jacob Hochhalter↗
NASA NTRSDate not supplied

Investigation of Ionic Liquids Isolated Iron for Ductile Iron Castings

As research continues for missions beyond low-Earth orbit, in-situ resource utilization (ISRU) methods are critical. To colonize the Lunar or Martian surface, the ability to manufacture mechanical and structural components with local resources is essential. Ionic liquids are being studied at NASA Marshall Space Flight Center (MSFC) to harvest elemental metals from meteorites and oxides in regolith. In this investigation, the viability of casting ductile iron using ionic liquids sourced iron and nickel was explored given ductile iron’s range of applications and performance as an as-cast alloy. Small ingots were produced using commercial silicon, manganese, and magnesium with carbon sourced from the by-products of a life support system currently being tested at MSFC. Samples were cast and compared to commercial ductile iron with phase transformation diagrams, microstructures, and hardness. Results showed ionic liquids sourced elements are a viable source of elemental alloying materials for a range of ductile iron alloys.

Blake Stewart↗
NASA NTRS2021

Investigation of Ionic Liquids Isolated Iron for Ductile Iron Castings

As research continues for missions beyond low-Earth orbit, in-situ resource utilization (ISRU) methods are critical. For Lunar and Martian colonization, the ability to manufacture mechanical and structural components with local resources is essential. Ionic liquids (IL) are being studied at NASA Marshall Space Flight Center (MSFC) to harvest elemental metals from meteorites and regolith oxides. In this investigation, the viability of casting ductile iron using ionic liquids sourced iron and nickel was explored given ductile iron’s range of applications and performance as an as-cast alloy. Ingots were produced using commercial elements to simulate the use of IL iron with carbon sourced from the by-products of a life support system currently tested at MSFC. Samples were cast and compared to commercial ductile iron with phase transformation diagrams,microstructures, and hardness. Results showed ionic liquids sourced elements are a viable source of elemental alloying materials for a range of ductile iron alloys.

Ionic Liquids↗
NASA NTRSDate not supplied

Composition-property correlations in NiTi-based shape memory alloys from the first principles

Development of shape memory alloys (SMA) has been traditionally accomplished by means of extensive empirical efforts, with a very limited support from phenomenological models and related tools. We present a theoretical framework based on the Hamiltonian formalism, which connects important thermodynamic properties directly to the relative energies (the eigenvalues of the Hamiltonian), computed from the first principles using density functional theory. The estimates based on this formalism allow to establish correlations between composition and physical properties, such as relative energies, phase transition temperatures, hysteresis, thermal expansion, and other thermodynamic information. Importantly, estimates and correlations not only provide a fast answer, but also elucidate underpinning of thermodynamic features in terms of the electronic structure. Using this framework, we consider phase transformations and correlations between the selected properties and composition in the NiTi-based ternary and multicomponent shape memory alloys. Our theoretical guidance facilitates design and development of future alloys.

shape memory alloys↗
NASA NTRSDate not supplied

Guided Design of Alloys, Strengthened via Precipitation

Using theoretical and computational guidance, we are designing stronger middle and high-entropy alloys and superalloys for the airspace applications. We focus on improving mechanical properties of materials at cryogenic and elevated temperatures. Here we discuss basic science and fundamental theory that are being used for guided design of next-generation alloys. As examples, we consider the medium-entropy NiCoCr alloy and precipitated superalloys with a local phase transformation strengthening. This research is funded by NASA’s Aeronautics Research Mission Directorate (ARMD) via Transformational Tools and Technologies (TTT) Project.

Alloys↗
NASA NTRS2022

Parallel Grand-Canonical Monte Carlo (ParaGrandMC) User’s Manual Version 2.0

This manual describes the commands and command line options for the Parallel Grand Canonical Monte Carlo version 2.0 (ParaGrandMC.2.0) simulation code. This is a highly scalable parallel FORTRAN 2003 code for simulating the thermodynamic evolution of materials at the atomic level, and predicting their thermodynamic state, phase diagram, chemical composition and mechanical properties. The code is specifically designed to simulate multi-component alloy systems, predict solid-state phase transformations such as austenite-martensite transformations, precipitate formation, recrystallization, capillary effects at interfaces, surface absorption, etc., which can aid the design of novel metallic alloys. While the software is mainly tailored for modeling metal alloys, it can also be used for other types of solid-state systems, and to some degree for liquid or gaseous systems, including multiphase systems forming solid-liquid-gas interfaces. In addition to performing Monte Carlo (MC) simulations, the code can also perform Molecular Dynamics (MD) and Langevin Dynamics (LD) simulations, which can be combined and interchanged with MC for faster and more efficient system evolution. A detailed description of the MC part of the code is provided in the NASA ParaGrandMC report: NASA/CR–2016-219202; http://www.sti.nasa.gov.

High performance computing↗
NASA NTRSDate not supplied

Guided Design of Alloys

Using multiscale materials modeling, we are designing stronger alloys for the airspace applications. We focus on improving mechanical properties of materials at operating temperature. We employ basic science and fundamental theory for guided design of the next-generation alloys. Among the examples, we consider precipitated superalloys with a local phase transformation strengthening. We acknowledge funding by NASA’s Aeronautics Research Mission Directorate (ARMD) via Transformational Tools and Technologies (TTT) Project.

multiscale↗
NASA NTRS2022

Laser Patterning Assisted Devitrification and Domain Engineering of Amorphous and Nanocrystalline Alloys

We have investigated laser-patterning and devitrification as a novel method to realize emergent properties in modified regions at the ribbon surface consisting of periodic localized laser spots thermally treated under rapid heating and cooling conditions. Fe-based amorphous ribbons were annealed for systematically varied laser power. Extremely high heating and cooling rates on the order of 10(exp 8)-10(exp 10)K/s have been estimated by finite element analysis simulations. Observations suggest surface melting followed by rapid solidification fast enough to quench and form an amorphous structure upon cooling. Diffusion of heat occurs from the laser irradiated surface region so that a finite volume of material surrounding this region rises in temperature above the crystallization temperature relevant for conventional isothermal annealing experiments. The underlying mechanism of laser annealing and consequences of heat transients involved are discussed in terms of impacts upon micro/nanostructure, residual stresses, and magnetic domain structure surrounding the laser irradiated region. The study illustrates the potential to exploit spatially optimized phase transformations in a scalable manufacturing process of amorphous and nanocrystalline alloys to locally access otherwise inaccessible extreme heating and cooling rates.

Amorphous ribbons↗
NASA NTRSDate not supplied

Guided Design of Alloys: Part 2

Using multiscale materials modeling, we are designing stronger alloys for the airspace applications. We focus on improving mechanical properties of materials at operating temperature. We employ basic science and fundamental theory for guided design of the next-generation alloys. Among the examples, we consider precipitated superalloys with a local phase transformation strengthening. We acknowledge funding by NASA’s Aeronautics Research Mission Directorate (ARMD) via Transformational Tools and Technologies (TTT) Project.

Multiscale↗
NASA NTRS2021

An evolutionary system of mineralogy, Part IV: Planetesimal differentiation and impact mineralization (4566 to 4560 Ma)

The fourth installment of the evolutionary system of mineralogy considers two stages of planetesimal mineralogy that occurred early in the history of the solar nebula, commencing by 4.566 Ga and lasting for at least 5 million years: (1) primary igneous minerals derived from planetesimal melting and differentiation into core, mantle, and basaltic components and (2) impact mineralization resulting in shock-induced deformation, brecciation, melting, and high-pressure phase transformations. We tabulate 90 igneous differentiated asteroidal minerals, including the earliest known occurrences of minerals with Ba, Cl, Cu, F, and V as essential elements, as well as the first appearances of numerous phosphates, quartz, zircon, and amphibole group minerals. We also record 40 minerals formed through high-pressure impact alteration, commencing with the period of asteroid accretion and differentiation. These stages of mineral evolution thus mark the first time that high pressures, both static and dynamic, played a significant role in mineral paragenesis.

Shaunna M. Morrison↗
NASA NTRSDate not supplied

Influence of Microstructural Features on Austenite-Martensite Interfaces in NiTi Shape Memory Alloys

Shape memory alloys (SMAs) exhibit several unique thermomechanical properties due to a reversible martensitic phase transformation. A key aspect of this transformation is the austenite-martensite interface. Here we present a molecular dynamics (MD) simulation methodology to study the atomic-scale features of austenite-martensite interface migration under near-equilibrium conditions. In single crystals, the interfaces migrate rapidly with only a small thermodynamic driving force. In polycrystals, however, interface migration is significantly impeded due to the change in orientation relationship at grain boundaries and the stored elastic energy resulting from microstructural constraints. This behavior can be linked to several mechanisms associated with transformation width and hysteresis in SMAs, properties of great importance for applications involving actuation. Additionally, we will present preliminary MD simulation results on the influence of precipitates on the formation and migration of austenite-martensite interfaces.

Gabriel Plummer↗
NASA NTRSDate not supplied

Influence of Microstructural Features on Austenite-Martensite Interfaces in NiTi Shape Memory Alloys

Shape memory alloys (SMAs) exhibit several unique thermomechanical properties due to a reversible martensitic phase transformation. A key aspect of this transformation is the austenite-martensite interface. Here we present a molecular dynamics (MD) simulation methodology to study the atomic-scale features of austenite-martensite interface migration under near-equilibrium conditions. In single crystals, the interfaces migrate rapidly with only a small thermodynamic driving force. In polycrystals, however, interface migration is significantly impeded due to the change in orientation relationship at grain boundaries and the stored elastic energy resulting from microstructural constraints. This behavior can be linked to several mechanisms associated with transformation width and hysteresis in SMAs, properties of great importance for applications involving actuation. Additionally, we will present preliminary MD simulation results on the influence of precipitates on the formation and migration of austenite-martensite interfaces.

Gabriel Plummer↗