Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “phase estimation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 973 records · Page 54
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

Moessbauer search for ferric oxide phases in lunar materials and simulated lunar materials

Moessbauer studies were carried out on lunar fines and on simulated lunar glasses containing magnetic-like precipitates with the primary objective of determining how much, if any, ferric oxide is present in the lunar soils. Although unambiguous evidence of lunar Fe(3+) phases was not obtained, an upper limit was estimated from different portions of the Moessbauer spectra to be between 0.1 and 0.4 wt.% (as Fe3O4). A smaller than 62 microns fraction of 15021,118 showed 0.5 wt.% ferromagnetic iron at 300 K in as-returned condition. After heating to 650 C in an evacuated, sealed quartz tube for 1400 hours, the same sample exhibited 1 wt.% ferromagnetic iron at room temperature. An accompanying decrease in excess absorption area near zero velocity was noted. Thus, the result of the vacuum heat treatment was to convert fine grained iron to larger particles, apparently without the oxidation effects commonly reported.

Forester, D. W.↗
NASA NTRS1975

Space Shuttle flight control system

The Space Shuttle is a control stabilized vehicle with control provided by an all digital, fly-by-wire flight control system. This paper gives a description of the several modes of flight control which correspond to the Shuttle mission phases. These modes are ascent flight control (including open loop first stage steering, the use of four computers operating in parallel and inertial guidance sensors), on-orbit flight control (with a discussion of reaction control, phase plane switching logic, jet selection logic, state estimator logic and OMS thrust vector control), entry flight control and TAEM (terminal area energy management to landing). Also discussed are redundancy management and backup flight control.

Klinar, W. J.↗
NASA NTRS1981

An error budget for the JPL hydrogen maser receiver

The hydrogen maser receiver is a synthesizer that converts the maser signal, at about 1420 MHz, to a set of output signals at 100, 20, 10, 5, 1, and 0.1 MHz. The contribution of the receiver and its component modules to the frequency instability and phase noise of each of its outputs is estimated, and these results are compared to published measurements of the 100-MHz output of the frequency standard, which consists of a maser plus its receiver. One can then assess how much the receiver degrades the performance of the frequency standard.

Greenhall, C. A.↗
NASA NTRS1982

Interaction of a cumulus cloud ensemble with the large-scale environment. III - Semi-prognostic test of the Arakawa-Schubert cumulus parameterization

The verification of the Arakawa and Schubert (1974) cumulus parameterization is continued using a semiprognostic approach. Observed data from Phase III of GATE are used to provide estimates of the large-scale forcing of a cumulus ensemble at each observation time. Instantaneous values of the precipitation and the warming and drying due to cumulus convection are calculated using the parameterization. The results show that the calculated precipitation agrees very well with estimates from the observed large-scale moisture budget and from radar observations. The calculated vertical profiles of cumulus warming and drying also are quite similar to the observed. It is shown that the closure assumption adopted in the parameterization (the cloud-work function quasi-equilibrium) results in errors of generally less than 10% in the calculated precipitation. The sensitivity of the parameterization to some assumptions of the cloud ensemble model and the solution method for the cloud-base mass flux is investigated.

Lord, S. J.↗
NASA NTRS1982

Mass estimation and discrimination during brief periods of zero gravity

Under zero gravity, the gravitational cues to mass are removed, but the inertial cues remain. A sensation of heaviness is generated if objects are shaken, and hence given a changing acceleration. A magnitude estimation experiment was conducted during the 0-G phase of parabolic flight and on the ground, and the results suggested that objects felt lighter under 0 G than under 1 G. Mass discrimination was also measured in flight, and yielded Weber fractions of .18 under 0 G, .16 under 1.8 G, and .09 under 1 G. Poor performance under microgravity and macrogravity was probably due mainly to lack of time for adaptation to changed G levels. It is predicted that discrimination should improve during the course of prolonged spaceflight, and that there should be an aftereffect of poor discrimination on return to earth.

Ross, H. E.↗
NASA NTRS1989

Access of energetic particles to storm time ring current through enhanced radial 'diffusion'

It is proposed that the transport of particles with energy of at least approximately 40 keV into the geomagnetic storm time ring current can result from enhanced stochastic radial transport driven by fluctuating electric fields during a storm's main phase. The effects of such electric fields are estimated by applying radial diffusion theory, assuming a preexisting trapped-particle population as the initial condition. The feasibility of explaining observed flux increases of particles of at least approximately 40 keV at no more than approximately 4 earth radii by enhanced radial 'diffusion' is then demonstrated. It is estimated that the at least approximately 40-keV portion of the storm time ring current at approximately 3 earth radii consists of about 50 percent preexisting and about 50 percent new particles. The formation of the storm time ring current is found to be perhaps explainable via a combination of direct radial transport at energies no greater than approximately 40 keV and 'diffusive' radial transport at higher energies.

Lyons, L. R.↗
NASA NTRS1989

Single chip fixed frequency bit synchronizer

A single chip, fixed frequency suboptimum bit synchronizer design which was implemented utilizing a programmable logic device is described. The bit synchronizer is modeled after a digital transition tracking loop for symbol estimation and employs a first-order incremental phase modulator for closed-loop symbol synchronization. The BER and tracking performance is modeled and compared to optimum designs. The bit synchronizer was developed for the Space Shuttle.

Butler, Madeline J.↗
NASA NTRS1990

In-Space technology experiments program. A high efficiency thermal interface (using condensation heat transfer) between a 2-phase fluid loop and heatpipe radiator: Experiment definition phase

Space Station elements and advanced military spacecraft will require rejection of tens of kilowatts of waste heat. Large space radiators and two-phase heat transport loops will be required. To minimize radiator size and weight, it is critical to minimize the temperature drop between the heat source and sink. Under an Air Force contract, a unique, high-performance heat exchanger is developed for coupling the radiator to the transport loop. Since fluid flow through the heat exchanger is driven by capillary forces which are easily dominated by gravity forces in ground testing, it is necessary to perform microgravity thermal testing to verify the design. This contract consists of an experiment definition phase leading to a preliminary design and cost estimate for a shuttle-based flight experiment of this heat exchanger design. This program will utilize modified hardware from a ground test program for the heat exchanger.

Pohner, John A.↗
NASA NTRS1992

Short- and intermediate-period oxygen-rich Miras

Available IR photometry and the period-IR luminosity relationship are used to analyze a nearly complete sample of oxygen-rich Miras at Galactic latitudes with /b/ greater than 30 deg. In agreement with previous kinematic studies, a marked difference is found in the spatial distributions between the stars with periods less than and those with periods greater than 300 d. For stars with periods in the range 300-400 d, the exponential scale height from the Galactic plane is close to 240 pc, the projected surface density is about 100/sq kpc, and the local space density is about 210/cu kpc. The progenitors of the Miras with periods greater than 300 d appear to be disk dwarfs with typical main-sequence masses of between 1.0 and 1.2 solar masses. The masses of the main-sequence progenitors of the short-period Miras are 1.1 solar masses or less. The duration of the Mira phase for the intermediate-period stars is estimated to be about 20,000 yr, somewhat longer than other recent estimates. Both short- and intermediate-period oxygen-rich Miras characteristically lose mass at about 10 exp -7 solar mass/yr.

Jura, M.↗
NASA NTRS1991

In-phase and out-of-phase axial-torsional fatigue behavior of Haynes 188 at 760 C

Isothermal, in-phase and out-of-phase axial-torsional fatigue experiments have been conducted at 760 C on uniform gage section, thin-walled tubular specimens of a wrought cobalt-base superalloy, Haynes 188. Test-control and data acquisition were accomplished with a minicomputer. Fatigue lives of the in- and out-of-phase axial-torsional fatigue tests have been estimated with four different multiaxial fatigue life prediction models that were developed primarly for predicting axial-torsional fatigue lives at room temperature. The models investigated were: (1) the von Mises equivalent strain range; (2) the Modified Multiaxiality Factor Approach; (3) the Modified Smith-Watson-Topper Parameter; and (4) the critical shear plane method of Fatemi, Socie, and Kurath. In general, life predictions by the von Mises equivalent strain range model were within a factor of 2 for a majority of the tests and the predictions by the Modified Multiaxiality Factor Approach were within a factor of 2, while predictions of the Modified Smith-Watson-Topper Parameter and of the critical shear plane method of Fatemi, Socie, and Kurath were unconservative and conservative, respectively, by up to factors of 4. In some of the specimens tested under combined axial-torsional loading conditions, fatigue cracks initiated near extensometer indentations. Two design modifications have been proposed to the thin-walled tubular specimen to overcome this problem.

Kalluri, Sreeramesh↗
NASA NTRS1994

Evaluation of GPS position and attitude determination for automated rendezvous and docking missions

The use of the Global Positioning System for position and attitude determination is evaluated for an automated rendezvous and docking mission. The typical mission scenario involves the chaser docking with the target for resupply or repair purposes, and is divided into three sections. During the homing phase, the chaser utilizes coarse acquisition pseudorange data to approach the target; guidance laws for this stage are investigated. In the second phase, differential carrier phase positioning is utilized. The chaser must maintain a quasiconstant distance from the target, in order to resolve the initial integer ambiguities. Once the ambiguities are determined, the terminal phase is entered, and the rendezvous is completed with continuous carrier phase tracking. Attitude knowledge is maintained in all phases through the use of the carrier phase observable. A Kalman filter is utilized to estimate all states from the noisy measurement data. The effects of selective availability and cycle slips are also investigated.

Diprinzio, Marc D.↗
NASA NTRS1994

Hot gas and the origin of the nebular continuum in novae

A featureless blue continuum (with constant f(sub nu)) is a defining feature of declining classical novae. The fact that f(sub nu) is constant into the infrared, and the absence of a Balmer jump, suggests that this continuum originates in hot tenous gas. The electron temperature and density of the hot gas phase of classical nova QU Vul 1984 are estimated from ground-based optical and IUE ultraviolet observations. This region has a temperature of 10(exp 5) - 10(exp 6), and a density in the range of 2 x 10(exp 4) to 3 x 10(exp 5)/cu cm. In addition, a colder, denser shell composed of many 'clumps' or condensations is present, and it is responsible for most of the optical-to-ultraviolet emission lines. The hot has, however, may be much more massive and could dominate the energetics of the ejecta. The total returned mass could be as high as 10(exp -4) and 4 x 10(exp -3) solar mass, depending on conditions in the hot gas. The large mass of the shell, in combination with the high metallicity found in this nova, supports the idea that novae may be an important contributor to the chemical enrichment of the interstellar medium.

Saizar, Pedro↗
NASA NTRS1995

An a priori model for the reduction of nutation observations: KSV(1994.3) nutation series

We discuss the formulation of a new nutation series to be used in the reduction of modern space geodetic data. The motivation for developing such a series is to develop a nutation series that has smaller short period errors than the IAU 1980 nutation series and to provide a series that can be used with techniques such as the Global Positioning System (GPS) that have sensitivity to nutations but can directly separate the effects of nutations from errors in the dynamical force models that effect the satellite orbits. A modern nutation series should allow the errors in the force models for GPS to be better understood. The series is constructed by convolving the Kinoshita and Souchay rigid Earth nutation series with an Earth response function whose parameters are partly based on geophysical models of the Earth and partly estimated from a long series (1979-1993) of very long baseline interferometry (VLBI) estimates of nutation angles. Secular rates of change of the nutation angles to represent corrections to the precession constant and a secular change of the obliquity of the ecliptic are included in the theory. Time dependent amplitudes of the Free Core Nutation (FCN) that is most likely excited by variations in atmospheric pressure are included when the geophysical parameters are estimated. The complex components of the prograde annual nutation are estimated simultaneously with the geophysical parameters because of the large contribution to the nutation from the S(sub 1) atmospheric tide. The weighted root mean square (WRMS) scatter of the nutation angle estimates about this new model are 0.32 mas and the largest correction to the series when the amplitudes of the ten largest nutations are estimated is 0.18 +/- 0.03 mas for the in phase component of the prograde 18. 6 year nutation.

Herring, T. A.↗
NASA NTRS1995

Evaluation of phase-diversity techniques for solar-image restoration

Phase-diversity techniques provide a novel observational method for overcomming the effects of turbulence and instrument-induced aberrations in ground-based astronomy. Two implementations of phase-diversity techniques that differ with regard to noise model, estimator, optimization algorithm, method of regularization, and treatment of edge effects are described. Reconstructions of solar granulation derived by applying these two implementations to common data sets are shown to yield nearly identical images. For both implementations, reconstructions from phase-diverse speckle data (involving multiple realizations of turbulence) are shown to be superior to those derived from conventional phase-diversity data (involving a single realization). Phase-diverse speckle reconstructions are shown to achieve near diffraction-limited resolution and are validated by internal and external consistency tests, including a comparison with a reconstruction using a well-accepted speckle-imaging method.

Paxman, Richard G.↗
NASA NTRS1996

Application of the pressure sensitive paint technique to steady and unsteady flow

Pressure sensitive paint is a newly-developed optical measurement technique with which one can get a continuous pressure distribution in much shorter time and lower cost than a conventional pressure tap measurement. However, most of the current pressure sensitive paint applications are restricted to steady pressure measurement at high speeds because of the small signal-to-noise ratio at low speed and a slow response to pressure changes. In the present study, three phases of work have been completed to extend the application of the pressure sensitive paint technique to low-speed testing and to investigate the applicability of the paint technique to unsteady flow. First the measurement system using a commercially available PtOEP/GP-197 pressure sensitive paint was established and applied to impinging jet measurements. An in-situ calibration using only five pressure tap data points was applied and the results showed good repeatability and good agreement with conventional pressure tap measurements on the whole painted area. The overall measurement accuracy in these experiments was found to be within 0.1 psi. The pressure sensitive paint technique was then applied to low-speed wind tunnel tests using a 60 deg delta wing model with leading edge blowing slots. The technical problems encountered in low-speed testing were resolved by using a high grade CCD camera and applying corrections to improve the measurement accuracy. Even at 35 m/s, the paint data not only agreed well with conventional pressure tap measurements but also clearly showed the suction region generated by the leading edge vortices. The vortex breakdown was also detected at alpha=30 deg. It was found that a pressure difference of 0.2 psi was required for a quantitative pressure measurement in this experiment and that temperature control or a parallel temperature measurement is necessary if thermal uniformity does not hold on the model. Finally, the pressure sensitive paint was applied to a periodically changing pressure field with a 12.8s time period. A simple first-order pole model was applied to deal with the phase lag of the paint. The unsteady pressure estimated from the time-changing pressure sensitive paint data agreed well with the pressure transducer data in regions of higher pressure and showed the possibility of extending the technique to unsteady pressure measurements. However, the model still needs further refinement based on the physics of the oxygen diffusion into the paint layer and the oxygen quenching on the paint luminescence.

Shimbo, Y.↗
NASA NTRS2002

Cloud Algorithm Design and Performance for the 2002 Geoscience Laser Altimeter System Mission

A satellite borne lidar instrument, the Geoscience Laser Altimeter System (GLAS), is to be launched in late 2002 and will provide continuous profiling of atmospheric clouds and aerosol on a global basis. Data processing algorithms have been developed to provide operational data products in near real time. Basic data products for cloud observations are the height of the top and bottom of single to multiple cloud layers and the lidar calibrated observed backscatter cross section up to the level of signal attenuation. In addition the optical depth and vertical profile of visible extinction cross section of many transmissive cloud layers and most haze layers are to be derived. The optical thickness is derivable in some cases from the attenuation of the molecular scattering below cloud base. In other cases an assumption of the scattering phase function is required. In both cases a estimated correction for multiple scattering is required. The data processing algorithms have been tested in part from aircraft measurements used to simulated satellite data. The GLAS lidar observations will be made from an orbit that will allow inter comparison with all other existing satellite cloud measurements.

Spinhirne, J. D.↗
NASA NTRS1995

Electrochromatographic separation of proteins

We have developed a modified electrochromatography system which minimizes Joule heating at electric field strengths up to 125 V/cm. A non-linear equilibrium model is described which incorporates electrophoretic mobility, hydrodynamic flow velocity, and an electrically induced concentration polarization at the surface of the stationary phase. This model is able to provide useful estimates of protein retention time and velocity in a column packed with Sephadex gel and subjected to an electric field. A correlation of electrophoretic mobility of peptide and proteins with respect to their charge, molecular mass, and asymmetry enables the selection of solute target molecules for electrochromatographic separations. Good separation of protein mixtures have been obtained.

NASA Discipline Life Support Systems↗
NASA NTRS2006

Numerical Modeling of Turbulence Effects within an Evaporating Droplet in Atomizing Sprays

A new approach to account for finite thermal conductivity and turbulence effects within atomizing liquid sprays is presented in this paper. The model is an extension of the T-blob and T-TAB atomization/spray model of Trinh and Chen (2005). This finite conductivity model is based on the two-temperature film theory, where the turbulence characteristics of the droplet are used to estimate the effective thermal diffhsivity within the droplet phase. Both one-way and two-way coupled calculations were performed to investigate the performance of this model. The current evaporation model is incorporated into the T-blob atomization model of Trinh and Chen (2005) and implemented in an existing CFD Eulerian-Lagrangian two-way coupling numerical scheme. Validation studies were carried out by comparing with available evaporating atomization spray experimental data in terms of jet penetration, temperature field, and droplet SMD distribution within the spray. Validation results indicate the superiority of the finite-conductivity model in low speed parallel flow evaporating spray.

Balasubramanyam, M. S.↗