SEARCH · Engineering Papers

Results for “performance contracting”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 973 records · Page 54

All sources NASA NTRS DOE OSTI

NASA NTRS2002

Rocket-Based Combined Cycle Flowpath Testing for Modes 1 and 4

Under sponsorship of the NASA Glenn Research Center (NASA GRC), the Johns Hopkins University Applied Physics Laboratory (JHU/APL) designed and built a five-inch diameter, Rocket-Based Combined Cycle (RBCC) engine to investigate mode 1 and mode 4 engine performance as well as Mach 4 inlet performance. This engine was designed so that engine area and length ratios were similar to the NASA GRC GTX engine is shown. Unlike the GTX semi-circular engine design, the APL engine is completely axisymmetric. For this design, a traditional rocket thruster was installed inside of the scramjet flowpath, along the engine centerline. A three part test series was conducted to determine Mode I and Mode 4 engine performance. In part one, testing of the rocket thruster alone was accomplished and its performance determined (average Isp efficiency = 90%). In part two, Mode 1 (air-augmented rocket) testing was conducted at a nominal chamber pressure-to-ambient pressure ratio of 100 with the engine inlet fully open. Results showed that there was neither a thrust increment nor decrement over rocket-only thrust during Mode 1 operation. In part three, Mode 4 testing was conducted with chamber pressure-to-ambient pressure ratios lower than desired (80 instead of 600) with the inlet fully closed. Results for this testing showed a performance decrease of 20% as compared to the rocket-only testing. It is felt that these results are directly related to the low pressure ratio tested and not the engine design. During this program, Mach 4 inlet testing was also conducted. For these tests, a moveable centerbody was tested to determine the maximum contraction ratio for the engine design. The experimental results agreed with CFD results conducted by NASA GRC, showing a maximum geometric contraction ratio of approximately 10.5. This report details the hardware design, test setup, experimental results and data analysis associated with the aforementioned tests.

Rice, Tharen↗

NASA NTRS2003

Functional Flight Test Report for Positive Systems' ADAR System 5500 Sensor SN8 Linear

This report describes results of the functional flight test conducted with the Positive Systems' ADAR 5500 sensor system (serial number 8, linear configuration) near Winslow, Arizona on June 30 and July 1, 1999. The in-flight test is one component of the NASA Scientific Data Purchase (SDP) Validation and Verification (V&V) process. It allows to measure characteristics of the entire sensor system affected by both performance of the sensor during a flight and post-flight image processing. The following characteristics were analyzed: changes of dark digital numbers (DN's), radiometric linearity, signal-to-noise ratio (SNR), spatial resolution, and geolocation accuracy. The measured characteristics were compared with the image product specifications defined in the Positive Systems' SDP contract. Dependence of the dark DN's on several factors was analyzed, but no significant correlation was found. However, the observed changes in dark DN's were relatively small, which justifies usage of a constant value in the dark DN subtraction procedure during post-processing. Dependence of measured at-sensor, in-band radiance (in arbitrary units) on measured in-band ground reflectance is very well described by a linear function - The sensor fulfills the linearity requirement. Measured SNR values lower than the contract specifications, but accuracy of that test was possibly affected by non-uniformity of the employed gray-scale panels. The SNR values are generally sufficiently high for most applications. SNR can also be improved during standard flights by using longer exposure times. Full width at half maximum (FWHM) of an edge response derived line spread function was used as a measure of spatial resolution. FWHM was generally smaller than twice the ground sample distance (GSD), in agreement with the contract specifications. Accuracy of the geolocation information, which is provided for the particular images in a metadata file, was found to meet contract requirements as well.

Stanley, Tom↗

NASA NTRS1995

Concept Designed and Developed for Distortion- Tolerant, High-Stability Engine Control

Engine Control Future aircraft turbine engines, both commercial and military, must be able to successfully accommodate expected increased levels of steady-state and dynamic engine-face distortion. Advanced tactical aircraft are likely to use thrust vectoring to enhance their maneuverability. As a result, the engines will see more extreme aircraft angles-of-attack and sideslip levels than are currently encountered with present-day aircraft. Also, the mixed-compression inlets needed for the High Speed Civil Transport will likely encounter disturbances similar to those seen by tactical aircraft, in addition to planar pulse, inlet buzz, and high distortion levels at low flight speed and off-design operation. The current approach of incorporating a sufficient component design stall margin to tolerate these increased levels of distortion would significantly reduce performance. The objective of the High Stability Engine Control (HISTEC) program is to design, develop, and flight demonstrate an advanced, high-stability, integrated engine-control system that uses measurement-based, real-time estimates of distortion to enhance engine stability. The resulting distortion-tolerant control reduces the required design stall margin, with a corresponding increase in performance and decrease in fuel burn. The HISTEC concept has been designed and developed, and the software implementing the concept has successfully accommodated time-varying distortion. The NASA Lewis Research Center is currently overseeing the development and validation of the hardware and software necessary to flight test the HISTEC concept. HISTEC is a contracted effort with Pratt & Whitney of West Palm Beach, Florida. The HISTEC approach includes two major systems: A Distortion Estimation System (DES) and Stability Management Control (SMC). DES is an aircraft-mounted, high-speed processor that estimates the amount and type of distortion present and its effect on the engine. It uses high-response pressure measurements at the engine face to calculate indicators of the type and extent of distortion in real time. From these indicators, DES determines the effects of distortion on the propulsion systems and the corresponding engine match point necessary to accommodate it. DES output consists of fan and compressor pressure ratio trim commands that are passed to the SMC. In addition, DES uses maneuver information, consisting of angle-of-attack and sideslip from the flight control, to anticipate high inlet distortion conditions. The SMC, which is contained in the engine-mounted, Improved Digital Electronic Engine Control (IDEEC), includes advanced control laws to directly control the fan and compressor transient operating line (pressure ratio). These advanced control laws, with a multivariable design, have the potential for higher bandwidth and the resulting more precise control of engine match. The ability to measure and assess the distortion effects in real time coupled with a high-response controller improves engine stability at high levels of distortion. The software algorithms implementing DES have been designed, developed, and demonstrated, and integration testing of the DES and SMC software has been completed. The results show that the HISTEC system will be able to sense inlet distortion, determine the effect on engine stability, and accommodate distortion by maintaining an adequate margin for engine surge. The Pratt &Whitney Comprehensive Engine Diagnostic Unit was chosen as the DES processor. An instrumented inlet case for sensing distortion was designed and fabricated. HISTEC is scheduled for flight test on the ACTIVE F-15 aircraft at the NASA Dryden Flight Research Center in Edwards, California, in late 1996.

Source record↗

NASA NTRS2018

High-Performance Spaceflight Computing (HPSC) Project Overview

The High Performance Spaceflight Computing (HPSC) multi-core processor Chiplet will provide a nearly two orders-of-magnitude improvement above the current state of the art for spaceflight processors, while also providing an unprecedented flexibility to tailor performance, power consumption, and fault tolerance to meet widely varying mission needs. These advancements will provide game changing improvements in computing performance, power efficiency, and flexibility, which will significantly improve the onboard processing capabilities of future NASA and Air Force space missions. HPSC is funded by NASA's Space Technology Mission Directorate (STMD), Science Mission Directorate (SMD), and the United States Air Force. The HPSC project is managed by Jet Propulsion Laboratory, and the HPSC contract is managed by NASA Goddard Space Flight Center (GSFC). Within the HPSC project, Boeing is under contract to NASA to develop prototype Chiplets, system software, and evaluation boards. As another development within the project, NASA Goddard Space Flight Center (GSFC) and the Jet Propulsion Laboratory (JPL) are developing middleware that will simplify application development for HPSC-based onboard processors.

multi-core processor↗

NASA NTRS2019

Maturation of Dynamic Power Convertors for Radioisotope Power Systems

Dynamic Radioisotope Power Systems (DRPS) are being developed by NASA's RPS Program in collaboration with the U.S. Department of Energy (DOE) for space science and exploration missions. A development effort is currently underway to mature dynamic power convertors for infusion into a potential future flight generator. This convertor maturation effort was formulated by the RPS Program at NASA Headquarters based on successful maturation models and utilizes expertise from agency technology and mission centers to support requirements development and technology assessments. The effort is being executed by Glenn Research Center's Dynamic Radioisotope Power Systems (DRPS) project and the Thermal Energy Conversion Branch. The Dynamic Power Convertor (DPC) contracts consist of three phases to enable design, fabrication, and independent assessment after delivery to the government. The contracts are intended to gather data on candidate dynamic conversion technologies to fill knowledge gaps, support assessments of dynamic conversion technologies, and elicit generator requirements. The SRG-110 (Stirling Radioisotope Generator) and ASRG (Advanced Stirling Radioisotope Generator) flight development projects provided Stirling convertor demonstration units and engineering models to verify and validate convertors against performance specifications and mission requirements. These units utilize temperature resistance materials and non-contacting bearings to demonstrate wear-free, long-life operation. This maturation effort builds on past lessons learned and new requirements focused on demonstrating convertor robustness to critical environments meant to stress key aspects of each convertor within the margins of the design. This effort seeks to realize the full potential of dynamic power conversion technologies for NASA's space science and exploration missions.

Wilson, Scott↗

NASA NTRS1989

Comparison of conceptual designs for 25 kWe advanced Stirling conversion systems for dish electric application

The Advanced Stirling Conversion System (ASCS) Project is managed by NASA Lewis Research Center through a cooperative interagency agreement with DOE. Conceptual designs for the ASCS's were completed under parallel contracts in 1987 by Mechanical Technology Inc. (MTI) of Latham, NY, and Stirling Technology Company (STC) of Richland, WA. Each design features a free-piston Stirling engine, a liquid metal heat pipe receiver, and a means to provide about 25 kW of electric power to a utility grid while meeting DOE's long term performance and cost goals. An independent assessment showed that both designs are manufacturable and have the potential to easily meet DOE's long term cost goals.

Shaltens, Richard K.↗

NASA NTRS1989

Comparison of conceptual designs for 25 kWe advanced Stirling conversion systems for dish electric applications

Shaltens, Richard K.↗

NASA NTRS1993

Software For Analyzing Performances Of Wind Tunnels

Subsonic Wind Tunnel Performance Analysis computer program developed as aid in design and analysis of subsonic wind tunnels. Brings together and refines previously scattered and oversimplified techniques used for design of, and prediction of losses in, components of subsonic wind tunnels. Implements system of equations for determining total pressure losses and provides general guidelines for design of diffusers, contractions, corners, and inlets and exits of nonreturn tunnels. Written in FORTRAN and BASIC.

Decker, C.↗

NASA NTRS1999

The Effect of Shared Information on Pilot/Controller And Controller/Controller Interactions

In order to respond to the increasing demand on limited airspace system resources, a number of applications of information technology have been proposed, or are under investigation, to improve the efficiency, capacity and reliability of ATM (Asynchronous Transfer Mode) operations. Much of the attention in advanced ATM technology has focused on advanced automation systems or decision aiding systems to improve the performance of individual Pilots or Controllers. However, the most significant overall potential for information technology appears to he in increasing the shared information between human agents such as Pilots, Controllers or between interacting Controllers or traffic flow managers. Examples of proposed shared information systems in the US include; Controller Pilot Databank Communication (CPDLC), Traffic Management Advisor (TMA); Automatic Dependent Surveillance (ADS); Collaborative Decision Making (CDM) and NAS Level Common Information Exchange. Air Traffic Management is fundamentally a human centered process consisting of the negotiation, execution and monitoring of contracts between human agents for the allocation of limited airspace, runway and airport surface resources. The decision processes within ATM tend to be Semistructured. Many of the routine elements in ATM decision making on the part of the Controllers or Pilots are well Structured and can be represented by well defined rules or procedures. However in disrupted conditions, the ATM decision processes are often Unstructured and cannot be reduced to a set of discrete rules. As a consequence, the ability to automate ATM processes will be limited and ATM will continue to be a human centric process where the responsibility and the authority for the negotiation will continue to rest with human Controllers and Pilots. The use of information technology to support the human decision process will therefore be an important aspect of ATM modernization. The premise of many of the proposed shared information systems is that the performance of ATM operations will improve with an increase in Shared Situation Awareness between agents (Pilots, Controller, Dispatchers). This will allow better informed control decisions and an improved ability to negotiate between agents. A common information basis may reduce communication load and may increase the level of collaboration in the decision process. In general, information sharing is expected to have advantages for all agents within the system. However there are important questions which remain to be,addressed. For example: What shared information is most important for developing effective Shared Situation Awareness? Are there issues of information saturation? Does information parity create ambiguity in control authority? Will information sharing induce undesirable or unstable gaming behavior between agents? This paper will explore the effect of current and proposed information sharing between different ATM agents. The paper will primarily concentrate on bilateral tactical interactions between specific agents (Pilot/Controller; Controller/Controller; Pilot/Dispatcher; Controller/Dispatcher) however it will also briefly discuss multilateral interaction and more strategic interactions.

Hansman, R. John↗

NASA NTRS1978

Transistor screening evaluation SJ6708H

A manufacturer was contracted to screen 125 transistors capable of withstanding the high level inductive voltages obtained when switching inductive loads. Planned differences included a change in die bonding to comply with NASA's desire for hard solder die attachment which further necessitated a change in package to conform to the required die mounting system. Evaluation of the electrical performance and recommended changes were made during the preliminary build phase of the program. The following sections are outlined: (1) narrative outline; (2) customer data summary and X-ray reports; (3) device specification; (4) failure analysis reports; (5) test facilities list; and (6) test measurement data.

Barton, J. L.↗

NASA NTRS1997

Adaptive Full Aperture Wavefront Sensor Study

This grant and the work described was in support of a Seven Segment Demonstrator (SSD) and review of wavefront sensing techniques proposed by the Government and Contractors for the Next Generation Space Telescope (NGST) Program. A team developed the SSD concept. For completeness, some of the information included in this report has also been included in the final report of a follow-on contract (H-27657D) entitled "Construction of Prototype Lightweight Mirrors". The original purpose of this GTRI study was to investigate how various wavefront sensing techniques might be most effectively employed with large (greater than 10 meter) aperture space based telescopes used for commercial and scientific purposes. However, due to changes in the scope of the work performed on this grant and in light of the initial studies completed for the NGST program, only a portion of this report addresses wavefront sensing techniques. The wavefront sensing techniques proposed by the Government and Contractors for the NGST were summarized in proposals and briefing materials developed by three study teams including NASA Goddard Space Flight Center, TRW, and Lockheed-Martin. In this report, GTRI reviews these approaches and makes recommendations concerning the approaches. The objectives of the SSD were to demonstrate functionality and performance of a seven segment prototype array of hexagonal mirrors and supporting electromechanical components which address design issues critical to space optics deployed in large space based telescopes for astronomy and for optics used in spaced based optical communications systems. The SSD was intended to demonstrate technologies which can support the following capabilities: Transportation in dense packaging to existing launcher payload envelopes, then deployable on orbit to form a space telescope with large aperture. Provide very large (greater than 10 meters) primary reflectors of low mass and cost. Demonstrate the capability to form a segmented primary or quaternary mirror into a quasi-continuous surface with individual subapertures phased so that near diffraction limited imaging in the visible wavelength region is achieved. Continuous compensation of optical wavefront due to perturbations caused by imperfections, natural disturbances, and equipment induced vibrations/deflections to provide near diffraction limited imaging performance in the visible wavelength region. Demonstrate the feasibility of fabricating such systems with reduced mass and cost compared to past approaches.

Robinson, William G.↗

NASA NTRS2010

Toolsets Maintain Health of Complex Systems

First featured in Spinoff 2001, Qualtech Systems Inc. (QSI), of Wethersfield, Connecticut, adapted its Testability, Engineering, and Maintenance System (TEAMS) toolset under Small Business Innovation Research (SBIR) contracts from Ames Research Center to strengthen NASA's systems health management approach for its large, complex, and interconnected systems. Today, six NASA field centers utilize the TEAMS toolset, including TEAMS-Designer, TEAMS-RT, TEAMATE, and TEAMS-RDS. TEAMS is also being used on industrial systems that generate power, carry data, refine chemicals, perform medical functions, and produce semiconductor wafers. QSI finds TEAMS can lower costs by decreasing problems requiring service by 30 to 50 percent.

Source record↗

NASA NTRS2007

Traceability of Software Safety Requirements in Legacy Safety Critical Systems

How can traceability of software safety requirements be created for legacy safety critical systems? Requirements in safety standards are imposed most times during contract negotiations. On the other hand, there are instances where safety standards are levied on legacy safety critical systems, some of which may be considered for reuse for new applications. Safety standards often specify that software development documentation include process-oriented and technical safety requirements, and also require that system and software safety analyses are performed supporting technical safety requirements implementation. So what can be done if the requisite documents for establishing and maintaining safety requirements traceability are not available?

Hill, Janice L.↗

NASA NTRS2018

Reconfiguration of NASA GRC's Vacuum Facility 6 for Testing of Advanced Electric Propulsion System (AEPS) Hardware

The NASA Hall Effect Rocket with Magnetic Shielding (HERMeS) 12.5 kW Hall thruster has been the subject of extensive technology maturation in preparation for development into a flight propulsion system. The HERMeS thruster is being developed and tested at NASA GRC and NASA JPL through support of the Space Technology Mission Directorate (STMD) and is intended to be used as the electric propulsion system on the Power and Propulsion Element (PPE) of the recently announced Deep Space Gateway (DSG). The Advanced Electric Propulsion System (AEPS) contract was awarded to Aerojet-Rocketdyne to develop the HERMeS system into a flight system for use by NASA. To address the hardware test needs of the AEPS project, NASA GRC launched an effort to reconfigure Vacuum Facility 6 (VF-6) for high-power electric propulsion testing including upgrades and reconfigurations necessary to conduct performance, plasma plume, and system level integration testing. Results of the verification and validation testing with HERMeS Technology Demonstration Unit (TDU)-1 and TDU-3 Hall thrusters are also included.

Peterson, Peter Y.↗

NASA NTRS2019

Maturation of Dynamic Power Convertors for Radioisotope Power Systems

Dynamic Radioisotope Power Systems (DRPS) are being developed by NASA’s Radioisotope Power Systems (RPS) Program in collaboration with the U.S. Department of Energy (DOE) for space science and exploration missions. A development effort is currently underway to mature dynamic power convertors for infusion into a potential future flight generator. This convertor maturation effort was formulated by the RPS Program at NASA Headquarters based on successful maturation models and utilizes expertise from agency’s technology and mission centers to support requirements development and technology assessments. The effort is being executed by Glenn Research Center’s (GRC) DRPS Project and the Thermal Energy Conversion Branch. The Dynamic Power Convertor (DPC) contracts consist of three phases to enable design, fabrication, and independent assessment of prototypes after delivery to the government. The contracts are intended to gather data on candidate dynamic conversion technologies to fill knowledge gaps, support assessments of dynamic conversion technologies, and elicit generator requirements. The 110-watt Stirling Radioisotope Generator (SRG-110) and Advanced Stirling Radioisotope Generator (ASRG) flight development projects provided Stirling convertor demonstration units and engineering models to verify and validate convertors against performance specifications and mission requirements. These units utilize temperature resistant materials and non-contacting bearings to demonstrate wear-free, long-life operation. This maturation effort builds on past lessons-learned and new requirements focused on demonstrating convertor robustness to critical environments meant to stress key aspects of each convertor within the margins of the design. This effort seeks to realize the full potential of dynamic power conversion technologies for NASA’s space science and exploration missions.

Wilson, Scott↗

NASA NTRS1993

Algorithm and code development for unsteady three-dimensional Navier-Stokes equations

In the last two decades, there have been extensive developments in computational aerodynamics, which constitutes a major part of the general area of computational fluid dynamics. Such developments are essential to advance the understanding of the physics of complex flows, to complement expensive wind-tunnel tests, and to reduce the overall design cost of an aircraft, particularly in the area of aeroelasticity. Aeroelasticity plays an important role in the design and development of aircraft, particularly modern aircraft, which tend to be more flexible. Several phenomena that can be dangerous and limit the performance of an aircraft occur because of the interaction of the flow with flexible components. For example, an aircraft with highly swept wings may experience vortex-induced aeroelastic oscillations. Also, undesirable aeroelastic phenomena due to the presence and movement of shock waves occur in the transonic range. Aeroelastically critical phenomena, such as a low transonic flutter speed, have been known to occur through limited wind-tunnel tests and flight tests. Aeroelastic tests require extensive cost and risk. An aeroelastic wind-tunnel experiment is an order of magnitude more expensive than a parallel experiment involving only aerodynamics. By complementing the wind-tunnel experiments with numerical simulations the overall cost of the development of aircraft can be considerably reduced. In order to accurately compute aeroelastic phenomenon it is necessary to solve the unsteady Euler/Navier-Stokes equations simultaneously with the structural equations of motion. These equations accurately describe the flow phenomena for aeroelastic applications. At Ames a code, ENSAERO, is being developed for computing the unsteady aerodynamics and aeroelasticity of aircraft and it solves the Euler/Navier-Stokes equations. The purpose of this contract is to continue the algorithm enhancements of ENSAERO and to apply the code to complicated geometries. During the last year, the geometric capability of the code was extended to simulate transonic flows, a wing with oscillating control surface. Single-grid and zonal approaches were tested. For the zonal approach, a new interpolation technique was introduced. The key development of the algorithm was an interface treatment between moving zones for a control surface using the virtual-zone concept. The work performed during the period, 1 Apr. 1992 through 31 Mar. 1993 is summarized. Additional details on the various aspects of the study are given in the Appendices.

Obayashi, Shigeru↗

NASA NTRS2010

Do-It-Yourself Additives Recharge Auto Air Conditioning

In planning for a return mission to the Moon, NASA aimed to improve the thermal control systems that keep astronauts comfortable and cool while inside a spacecraft. Goddard Space Flight Center awarded a Small Business Innovation Research (SBIR) contract to Mainstream Engineering Corporation, of Rockledge, Florida, to develop a chemical/mechanical heat pump. IDQ Inc., of Garland, Texas, exclusively licensed the technology and incorporates it into its line of Arctic Freeze products for automotive air conditioning applications. While working on the design, Mainstream Engineering came up with a unique liquid additive called QwikBoost to enhance the performance of the advanced heat pump design.

Source record↗

NASA NTRS1987

Large-scale Advanced Prop-fan (LAP) static rotor test report

Discussed is Static Rotor Testing of the SR-7L Large Scale Advanced Prop-Fan (LAP). The LAP is an advanced 9 foot diameter, 8 bladed propeller designed and built by Hamilton Standard under contract to the NASA Lewis Research Center. The Prop-Fan employs thin swept blades to provide efficient propulsion at flight speeds up to Mach .85. Static Testing was conducted on a 10,000 HP whirl rig at Wright Patterson Air Force Base. The test objectives were to investigate the Prop-Fan static aerodynamic and structural dynamic performance, determine the blade steady state stressers and deflections and to measure steady and unsteady pressures on the SR-7L blade surface. The measured performance of the LAP correlated well with analytical predictions at blade pitch angles below 30 deg. A stall buffet phenomenon was observed at blade pitch angles above 30 deg. This phenomenon manifested itself by elevated blade vibratory stress levels and lower than expected thrust produced and power absorbed by the Prop-Fan for a given speed and blade angle.

Degeorge, Charles L.↗