Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “niobium”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 973 records · Page 54
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Twisted, multifilament Nb3Sn superconductive ribbon

An experimental study of superconductor stabilization has resulted in the successful application of the concepts of filamentary structure and conductor twist to Nb3Sn ribbon. The Nb3Sn is formed in parallel, helical paths, which are continuous around the ribbon. Short lengths (12-18cm) of 1.27 cm wide superconductive ribbon were produced. The filamentary and twist characteristics are incorporated in the ribbon by means of an inert mask formed on the ribbon surface early in the fabrication process. Diffusion reaction of the niobium and tin is prevented at the filament boundaries. Described are the conductor methods of fabrication, and test results obtained. The technology required to adapt the processes for the production of long lengths of ribbon is available.

Coles, W. D.↗
NASA NTRS1972

In-pile and out-of-pile testing of a molybdenum-uranium dioxide cermet fueled themionic diode

The behavior of Mo-UO2 cermet fuel in a diode for thermionic reactor application was studied. The diode had a Mo-0.5 Ti emitter and niobium collector. Output power ranged from 1.4 to 2.8 W/cm squared at emitter and collector temperatures of 1500 deg and 540 C. Thermionic performance was stable within the limits of the instrumentation sensitivity. Through 1000 hours of in-pile operation the emitter was dimensionally stable. However, some fission gases (15 percent) leaked through an inner clad imperfection that occurred during fuel fabrication.

Diianni, D. C.↗
NASA NTRS1972

Liquid metal boiling inception

An experimental study of the inception of boiling in potassium in forced convection is reported. The boiler consisted of a 0.19-inch inside diameter, niobium-1% zirconium boiler tube approximately six feet long. Heating was accomplished by direct electrical tube wall conduction. Experiments were performed with both all-liquid fill and two-phase fill startup sequences and with a range of flow rates, saturation temperatures, inert gas levels, and fill liquid temperatures. Superheat of the liquid above the equilibrium saturation temperature was observed in all the experiments. Incipient boiling liquid superheat ranged from a few degrees to several hundred. Comparisons of these data with other data and with several analytical treatments are presented.

Sabin, C. M.↗
NASA NTRS1971

Design of an external-fueled thermionic diode for in-pile testing.

Description of an external-fueled thermionic diode suitable for in-pile testing in a research reactor. The active electrode area is 94 sq cm. The 10-in. long, 1.5-in.-OD emitter body is tungsten 2% thoria. The fuel is contained in six 0.4-in.-diam holes equally spaced about the 0.5-in. central emitter hole. The collector is niobium-1% zirconium. The expected diode performance is 6 W/sq cm at 2000 K. In addition to following the constraints imposed by the in-pile testing and the electrically heated performance mapping prior to insertion in-pile, the diode will have end configurations prototypical of those anticipated for a flow-through, NaK-cooled, external-fuel thermionic reactor.

Ernst, D. M.↗
NASA NTRS1971

Reactor core length, externally configured thermionic converter.

Results of testing a converter having an external emitter configuration for 190 hours using RF induction heating. The converter was assembled with a rhenium emitter, 25.4 cm long, having a 91.2 sq cm emitting area, and a niobium collector with a molybdenum coating to improve its electronic property. The collector was water-cooled. The test included: static power output measurements, dynamic characteristics, and the effects of the temperature distribution along the emitter. The maximum power output achieved from the converter at an emitter temperature of 1942 K was 178 W at 0.48 V output, with a power density of 1.95 W/sq cm and an efficiency of 5.5%. The static characteristics also indicated that, with a constant power input, the converter power output does not vary with the output voltage as a result of self-adjustment of the emitter temperature. An investigation of the effects of the temperature distribution along the emitter length showed a 33% improvement in the converter output power with a flattening of the emitter temperature.

Shimada, K.↗
NASA NTRS1971

Comparison of computer-acquired performance data from several fixed spaced planar diodes.

Performance data are compared for thermionic diodes with various tungsten or rhenium emitters and niobium or molybdenum collectors. The planar converters have guard-ringed collectors and a fixed space of 10 mils (0.254 mm). The data were acquired using a computer. The parameters are the temperatures of the emitter Te, collector Tc, and cesium reservoir Tr. The composite plots have constant Te and varying Tc or Tr or both. The envelope and composite plots having constant Te are presented. The diodes were tested at increments between 1500 and 2000 K for the emitters, 750 and 1100 K for the collectors, and 520 and 650 K for the reservoirs.

Manista, E. J.↗
NASA NTRS1972

Friction, wear and noise of slip ring and brush contacts for synchronous satellite use.

A program is being conducted for testing of slip rings for synchronous orbit application. Instrumentation systems necessary for monitoring electrical noise, friction, and brush wear at atmospheric pressure and at less than 50 ntorr have been developed. A multiplex scheme necessary for the simultaneous recording of brush displacement, friction, and electrical noise has also been developed. Composite brushes consisting of silver-molybdenum disulfide-graphite and silver-niobium diselenide-graphite have been employed on rings of coin silver and rhodium plate. Four contact combinations have been tested during an ambient condition run-in at 150 rpm and a humidity sequence at 0.1 rpm. The first six months of the two year vacuum test at 0.1 rpm have been completed. Electrical noise, friction and brush wear data recorded during these periods have been analyzed.

Lewis, N. E.↗
NASA NTRS1972

Developmental status of thermionic materials.

Description of the reference materials selected for the major components of the unit cell of a thermionic pile element (TFE), the out-of-pile and in-pile test results, and current efforts for improving the life and performance of thermionic fuel elements. The component materials are required to withstand the fuel burnup and fast neutron fluence dictated by the thermionic reactor system. Tungsten was selected as the cladding material because of its compatibility with both the carbide and the oxide fuel materials. Niobium was selected as the collector material because its thermal expansion coefficient matches closely with that of the thin aluminum oxide layer used to electrically insulate the collector from the TFE sheath. An unfueled converter has performed stably over 41,000 hr. Accelerated irradiation tests have attained burnups equivalent to that for 40,000 hr of the thermionic reactor under consideration.

Yang, L.↗
NASA NTRS1972

High temperature (1200 C) ceramic-to-metal seal development

Two phases have been completed, of a program whose ultimate objective is the development of an alkali metal resistant, thermal shock resistant, leak-tight, and neutron radiation resistant ceramic-to-metal seal capable of operation at 1200 C for three to five years. The first phase involved the screening of platinum-base, vanadium-base and vanadium-niobium base brazes for the joining of Cb-1Zr or T-111 alloys to high purity alumina. The second phase involved studies of the performance of sealed capsule samples during 5000-hour aging tests at 800, 1000, and 1200 C in high vacuum. Sealed capsules which were made using pure vanadium braze, and were brazed at 1850 C for one minute, survived 64 thermal cycles to 1200 C at the heating/cooling rate of 100 C/minute. Vanadium braze samples survived 5000-hour aging tests at 800, 1000, and 1200 C. One thermally cycled sample survived a subsequent 5000-hour aging period at 1000 C, but another, at 1200 C, did not survive. It was concluded that a pure vanadium braze used to bond high purity alumina to Cb-1Zr alloy is the best of the systems studied, but that additional studies must be performed to establish its service temperature limitations for the desired three to five years' service.

Mckisson, R. L.↗
NASA NTRS1973

Measured catalycities of various candidate space shuttle thermal protection system coatings at low temperatures

Atom recombination catalytic rates for surface coatings of various candidate thermal protection system materials for the space shuttle vehicle were obtained from measurements in arc jet, air flow. The coatings, chrome oxides, siliconized carbon/carbon, hafnium/tantalum carbide on carbon/carbon, and niobium silicide, were bonded to the sensitive surface of transient slug calorimeters that measured the heat transfer rates to the coatings. The catalytic rates were inferred from these heat transfer rates Surface temperatures of the calorimeters varied from approximately 300 to 410 K.

Scott, C. D.↗
NASA NTRS1973

Postoperational examination of an externally configured thermionic converter

An externally configured thermionic converter was operated for 200 h. The converter was disassembled and examined to determine internal changes as a result of operation. The metal/ceramic seals and all joints were unaffected by operation. Converter output voltage and operational time were sufficient to produce electrolysis of stabilized zirconia spacers used in the converter. Surface analysis of the electrode surfaces indicated the presence on the tungsten emitter of only oxygen, carbon, and silicon. The niobium collector was, however, 25 to 40% covered with other elements. This coverage represented all elements present within the converter as construction materials other than silicon and tungsten, which were not detected on the collector, and carbon, which was detected only in small amounts.

Phillips, W. M.↗
NASA NTRS1973

Identification of a new lithium oxide, Li3O2

Lithium oxide (Li3O2) was prepared by decomposing anhydrous lithium hydroxide at 360 C in 48 hours and between 640 and 730 C in times up to 1.3 hours and pressures of about 0.00001 torr. Decompositions were done in nickel, molybdenum, niobium, tantalum, and the T-111 tantalum alloy (Ta - 8-wt.% W - 2 wt.% Hf) containers. This oxide probably belongs to the simple orthorhombic system with the following lattice parameters: a = 108.4 + or - 0.4 nm (10.84 + or - 0.04 A), b = 128.4 + or - 0.5 nm (12.84 + or - 0.05 A), and c = 103.6 + or - 0.4 nm (10.36 + or - 0.04 A).

Stecura, S.↗
NASA NTRS1973

Application of diffusion barriers to the refractory fibers of tungsten, columbium, carbon and aluminum oxide

A radio frequency powered ion-plating system was used to plate protective layers of refractory oxides and carbide onto high strength fiber substrates. Subsequent overplating of these combinations with nickel and titanium was made to determine the effectiveness of such barrier layers in preventing diffusion of the overcoat metal into the fibers with consequent loss of fiber strength. Four substrates, five coatings, and two metal matrix materials were employed for a total of forty material combinations. The substrates were tungsten, niobium, NASA-Hough carbon, and Tyco sapphire. The diffusion-barrier coatings were aluminum oxide, yttrium oxide, titanium carbide, tungsten carbide with 14% cobalt addition, and zirconium carbide. The metal matrix materials were IN 600 nickel and Ti 6/4 titanium. Adhesion of the coatings to all substrates was good except for the NASA-Hough carbon, where flaking off of the oxide coatings in particular was observed.

Douglas, F. C.↗
NASA NTRS1973

Fabrication of cermet bearings for the control system of a high temperature lithium cooled nuclear reactor

The techniques used to fabricate cermet bearings for the fueled control drums of a liquid metal cooled reference-design reactor concept are presented. The bearings were designed for operation in lithium for as long as 5 years at temperatures to 1205 C. Two sets of bearings were fabricated from a hafnium carbide - 8-wt. % molybdenum - 2-wt. % niobium carbide cermet, and two sets were fabricated from a hafnium nitride - 10-wt. % tungsten cermet. Procedures were developed for synthesizing the material in high purity inert-atmosphere glove boxes to minimize oxygen content in order to enhance corrosion resistance. Techniques were developed for pressing cylindrical billets to conserve materials and to reduce machining requirements. Finishing was accomplished by a combination of diamond grinding, electrodischarge machining, and diamond lapping. Samples were characterized in respect to composition, impurity level, lattice parameter, microstructure and density.

Yacobucci, H. G.↗
NASA NTRS1973

Friction, wear, and noise of slip ring and brush contacts for synchronous satellite use.

A program is being conducted for testing of slip rings for synchronous orbit application. Instrumentation systems necessary for monitoring electrical noise, friction, and brush wear at atmospheric pressure and at less than 50 nanotorr have been developed. A multiplex scheme necessary for the simultaneous recording of brush displacement, friction, and electrical noise has also been developed. Composite brushes consisting of silver-molybdenum disulfide-graphite and silver-niobium diselenide-graphite have been employed on rings of coin silver and rhodium plate. Brush property measurements made included measurement of density, electrical resistivity, shear strength, and microstructure.

Lewis, N. E.↗
NASA NTRS1973

Determination of work functions near melting points of refractory metals by using a direct-current arc.

A direct-current arc in argon at atmospheric pressure was used to determine effective work functions of refractory metals, including tantalum, tungsten, molybdenum, and niobium. The procedure is experimentally advantageous, because surface cleanliness of the specimen is not critical, high vacuum is not required, and the anode-cathode spacing is not critical. The experimental procedure involves striking an arc to a metal wire cathode to form a melted ball having an emitting area defined by its diameter. The literature melting point of the metal is taken as the emitting temperature. By using these parameters and the known arc current, effective work functions were calculated from the Richardson-Dushman equation. The calculated work functions agree with recommended handbook values to within about 0.1 V and have typical repeatabilities of 0.02 V.

Gordon, W. A.↗
NASA NTRS1973

The activation energy for creep of columbium /niobium/.

The activation energy for creep of nominally pure columbium (niobium) was determined in the temperature range from 0.4 to 0.75 T sub M by measuring strain rate changes induced by temperature shifts at constant stress. A peak in the activation energy vs temperature curve was found with a maximum value of 160 kcal/mole. A pretest heat treatment of 3000 F for 30 min resulted in even higher values of activation energy (greater than 600 kcal/mole) in this temperature range. The activation energy for the heat-treated columbium (Nb) could not be determined near 0.5 T sub M because of unusual creep curves involving negligible steady-state creep rates and failure at less than 5% creep strain. It is suggested that the anomalous activation energy values and the unusual creep behavior in this temperature range are caused by dynamic strain aging involving substitutional atom impurities and that this type of strain aging may be in part responsible for the scatter in previously reported values of activation energy for creep of columbium (Nb) near 0.5 T sub M.

Klein, M. J.↗
NASA NTRS1973

Design and operation of a 1000 C lithium-cesium test system

A 100 kWt cesium-lithium test loop fabricated of niobium-1% zirconium for experiments on erosion and two-phase system operation at temperatures of 980 C and velocities of 150 m/s. Although operated at design temperature for 100 hours, flow instabilities in the two-phase separator interfered with the achievement of the desired mass flow rates. A modified separator was fabricated and installed in the loop to alleviate this problem.

Hays, L. G.↗