Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “multilayers.”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 973 records · Page 54
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Synthesis of new two-dimensional titanium carbonitride Ti 2 C 0.5 N 0.5 T x MXene and its performance as an electrode material for sodium-ion battery

Two-dimensional (2D) layered transition metal carbides/nitrides, called MXenes, are attractive alternative electrode materials for electrochemical energy storage. Owing to their metallic electrical conductivity and low ion diffusion barrier, MXenes are promising anode materials for sodium-ion batteries (SIBs). Herein, we report on a new 2D carbonitride MXene, viz ., Ti 2 C 0.5 N 0.5 T x (T x stands for surface terminations), and the only second carbonitride after Ti 3 CNT x so far. A new type of in situ HF (HCl/KF) etching condition was employed to synthesize multilayer Ti 2 C 0.5 N 0.5 T x powders from Ti 2 AlC 0.5 N 0.5 . Spontaneous intercalation of tetramethylammonium followed by sonication in water allowed for large-scale delamination of this new titanium carbonitride into 2D sheets. Multilayer Ti 2 C 0.5 N 0.5 T x powders showed higher specific capacities and larger electroactive surface area than those of Ti 2 CT x powders. Multilayer Ti 2 C 0.5 N 0.5 T x powders show a specific capacity of 182 mAh g -1 at 20 mA g -1 , the highest among all reported MXene electrodes as SIBs with excellent cycling stability.

25 ENERGY STORAGE↗
DOE OSTI2023

Pulsed laser ejection of single-crystalline III-V solar cells from GaAs substrates

The best III-V solar cells start out as single-crystalline multilayers on GaAs substrates. Separating these multilayers from their growth substrate enables higher performance and wafer reuse, which are both critical for terrestrial III-V solar cell viability. Here, we remove rigidly bonded, 16 mm 2 x 3.5μm thick devices from a GaAs substrate using an unfocused Nd:YAG laser pulse. The pulse is absorbed by a low-bandgap, lattice-matched layer below the device, driving an ablation event that ejected the crystalline multilayer from the substrate. Minutes of selective wet-chemical etching and device finishing yield a 0.1 cm 2 device with a 17.4% power conversion efficiency and open-circuit voltage of 1.07 V, using AM1.5 direct with no anti-reflection coating. We show that the performance is comparable to similar cells produced via conventional processes. We discuss unique process characteristics, such as the potential to separate wafer-sized solar cells per laser pulse.

14 SOLAR ENERGY↗
DOE OSTI2024

Adsorption Thermodynamics for Process Simulation

Adsorption has rapidly evolved in recent decades and is an established separation technology extensively practiced in gas separation industries and others. However, rigorous thermodynamic modeling of multicomponent adsorption equilibrium remains elusive, and industrial practitioners rely heavily on expensive and time-consuming trial-and-error pilot studies to develop adsorption units. Here, this article highlights the need for rigorous adsorption thermodynamic models and the limitations and deficiencies of existing models such as the extended Langmuir isotherm, dual-process Langmuir isotherm, and adsorbed solution theory. It further presents a series of recent advances in the generalization of the classical Langmuir isotherm of single-component adsorption by deriving an activity coefficient model to account for the adsorbed phase adsorbate–adsorbent interactions, substituting adsorbed phase adsorbate and vacant site concentrations with activities, and extending to multicomponent competitive adsorption equilibrium, both monolayer and multilayer. Requiring a minimum set of physically meaningful model parameters, the generalized Langmuir isotherm for monolayer adsorption and the generalized Brunauer–Emmett–Teller isotherm for multilayer adsorption address various thermodynamic modeling challenges including adsorbent surface heterogeneity, isosteric enthalpies of adsorption, BET surface areas, adsorbed phase nonideality, adsorption azeotrope formation, and multilayer adsorption. Also discussed is the importance of quality adsorption data that cover sufficient temperature, pressure, and composition ranges for reliable determination of the model parameters to support adsorption process simulation, design, and optimization.

09 BIOMASS FUELS↗
DOE OSTI2025

Two-Dimensional Tantalum Carbo-Selenide for Hydrogen Evolution

Herein, we report the synthesis of two-dimensional Ta 2 Se 2 C (2D-Ta 2 Se 2 C) nanosheets using electrochemical lithiation in multilayer Ta 2 Se 2 C followed by sonication in deionized water. Multilayer Ta 2 Se 2 C was obtained via solid-state synthesis of Fe x Ta 2 Se 2 C followed by chemical etching of Fe. 2D-Ta 2 Se 2 C exhibited promising electrocatalytic activity for the hydrogen evolution reaction from water compared to multilayer Ta 2 Se 2 C and 2D-TaSe 2 . 2D-Ta 2 Se 2 C showed an overpotential at 10 mA·cm -2 (η 10 ) of 264 mV, a Tafel slope of 91 mV·dec -1 , and an electrochemically active surface area of 17.61 m ECSA 2 ·g catalyst -1 . The high performance could be attributed to the large surface area of single sheets which hence maximizes the number of exposed catalytic sites and increased density of vacancies, observed with transmission electron microscopy, during synthesis and processing.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Long-Range Charge Transport Facilitated by Electron Delocalization in MoS 2 and Carbon Nanotube Heterostructures

Controlling charge transport at the interfaces of nanostructures is crucial for their successful use in optoelectronic and solar energy applications. Mixed-dimensional heterostructures based on single-walled carbon nanotubes (SWCNTs) and transition metal dichalcogenides (TMDCs) have demonstrated exceptionally long-lived charge-separated states. However, the factors that control the charge transport at these interfaces remain unclear. In this study, we directly image charge transport at the interfaces of single- and multilayered MoS 2 and (6,5) SWCNT heterostructures using transient absorption microscopy. We find that charge recombination becomes slower as the layer thickness of MoS 2 increases. This behavior can be explained by electron delocalization in multilayers and reduced orbital overlap with the SWCNTs, as suggested by nonadiabatic (NA) molecular dynamics (MD) simulations. Dipolar repulsion of interfacial excitons results in rapid density-dependent transport within the first 100 ps. Stronger repulsion and longer-range charge transport are observed in heterostructures with thicker MoS 2 layers, driven by electron delocalization and larger interfacial dipole moments. These findings are consistent with the results from NAMD simulations. Our results suggest that heterostructures with multilayer MoS 2 can facilitate long-lived charge separation and transport, which is promising for applications in photovoltaics and photocatalysis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Substrate-Directed Dimensional and Phase Control of Peptide Assemblies on Two-Dimensional van der Waals Materials

Understanding and controlling biomolecular self-assembly on van der Waals (vdW) materials has the potential to advance hybrid bioelectronic devices by enabling precise tuning of the interface and modulation of the resulting electronic properties of the biomolecule-vdW heterostructure. However, how surface properties of vdW materials direct biomolecule assembly remains poorly understood. To fill this knowledge gap, we investigated the assembly of a peptide known to assemble into two-dimensional (2D) crystalline films on MoS 2 on three representative vdW surfaces: WS 2 , MoS 2 , and highly oriented pyrolytic graphite (HOPG). Using in situ atomic force microscopy (AFM), we find that assembly is substrate-dependent, resulting in multilayers on WS 2 , monolayers on MoS 2 , and multiple coexisting phases on HOPG. WS 2 exhibits a higher negative charge, strong long-range electrostatic interactions, and extensive hydration layering that may promote multilayer stacking. In contrast, MoS 2 has stronger short-range interactions with the peptides but much weaker long-range interactions and hydration structure, which may favor monolayer formation. Molecular dynamics simulations predict a corresponding switch from monolayer to multilayer aggregates of the adsorbed monomers, reflected in their relative mobilities. On hydrophobic HOPG, the peptides bind most strongly and remain as monomers with high surface mobility. The peptide dimers comprising the basic unit of the crystals are more compact on HOPG, which has a smaller lattice constant than WS 2 or MoS 2 , suggesting strain contributes to stabilizing multiple phases. Our results provide mechanistic insights into how surface charge and hydration structure, and the lattice structure of the substrates governs peptide assembly on vdW materials, offering a framework to rationally control the 2D peptide-vdW heterostructures.

Molecular dynamics simulations↗
DOE OSTI2020

Tuning the Chern number in quantum anomalous Hall insulators

A quantum anomalous Hall (QAH) state is a two-dimensional topological insulating state that has a quantized Hall resistance of h/(Ce 2 ) and vanishing longitudinal resistance under zero magnetic field (where h is the Planck constant, e is the elementary charge, and the Chern number C is an integer). The QAH effect has been realized in magnetic topological insulators and magic-angle twisted bilayer graphene. However, the QAH effect at zero magnetic field has so far been realized only for C = 1. Here we realize a well quantized QAH effect with tunable Chern number (up to C = 5) in multilayer structures consisting of alternating magnetic and undoped topological insulator layers, fabricated using molecular beam epitaxy. The Chern number of these QAH insulators is determined by the number of undoped topological insulator layers in the multilayer structure. Moreover, we demonstrate that the Chern number of a given multilayer structure can be tuned by varying either the magnetic doping concentration in the magnetic topological insulator layers or the thickness of the interior magnetic topological insulator layer. We develop a theoretical model to explain our experimental observations and establish phase diagrams for QAH insulators with high, tunable Chern number. Furthermore, the realization of such insulators facilitates the application of dissipationless chiral edge currents in energy-efficient electronic devices, and opens up opportunities for developing multi-channel quantum computing and higher-capacity chiral circuit interconnects.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Dissecting neurofilament tail sequence-phosphorylation-structure relationships with multicomponent reconstituted protein brushes

Neurofilaments (NFs) are multisubunit, bottlebrush-shaped intermediate filaments abundant in the axonal cytoskeleton. Each NF subunit contains a long intrinsically disordered tail domain, which protrudes from the NF core to form a “brush” surrounding each NF. Precisely how the tails’ variable charge patterns and repetitive phosphorylation sites mediate their conformation within the brush remains an open question in axonal biology. We address this problem by grafting recombinant NF tail protein constructs NF-Light, -Medium, and -Heavy (NFL, NFM, and NFH) to surfaces, yielding protein brushes of defined stoichiometry that can be phosphorylated in vitro. Atomic force microscopy measurements reveal that brush height depends on composition monotonically but not always linearly for binary NFL:NFM or NFL:NFH systems, and that NFM-based brushes are highly extended, while brushes incorporating the much larger NFH are surprisingly compact even after multisite phosphorylation. Complementary self-consistent field theory (SCFT) predicts multilayer brush morphologies for NFM and phosphorylated NFH brushes. Further experiments and SCFT analysis with designed mutants reveal that N-terminal negative charges in the NFH tail repel phosphorylated residues to generate the multilayer morphology, while the C-terminal charge-neutral region contributes to multilayer brush morphology but not total brush height. Charge-shuffled NFM variants show that charge segregation promotes brush collapse near physiological ionic strengths. Collectively, this study supports a role for NFM in establishing a dynamic range for NF brush conformation, lending insight into previous in vitro and in vivo findings. More broadly, this work establishes a platform for dissecting contributions of disordered protein sequence to conformation at interfaces.

Science & Technology - Other Topics↗
DOE OSTI2021

Canted standing spin-wave modes of permalloy thin films observed by ferromagnetic resonance

Non-collinear spin structures in materials that combine perpendicular and in-plane magnetic anisotropies are of great technological interest for microwave and spin wave-assisted magnetization switching. [Co/Pt] multilayers are well-known perpendicular anisotropy materials that have the potential to pin the magnetization of a soft magnetic layer, such as permalloy (Py), that has in-plane anisotropy, thereby forming a magnetic exchange spring. Here we report on multilayered [Co/Pt]/Pt/Py films, where an additional ultrathin Pt spacer has been included to control the coupling between the sub-units with in-plane and perpendicular magnetic anisotropy. Vector network analyser (VNA)-ferromagnetic resonance (FMR) measurements were made to obtain a complete picture of the resonant conditions, while the dynamical response of the sub-units was probed by synchrotron-based element- and phase selective x-ray detected FMR (XFMR). For all samples, only slight pinning of the dynamic magnetization of the Py by the [Co/Pt] was noted, and the FMR results were dominated by the 50 nm thick Py layer. Out-of-plane VNA-FMR maps reveal the presence of additional modes, e.g. a perpendicular standing spin-wave (PSSW) state. However, as the magnetic field is reduced below the saturation field, the PSSW state morphs continuously through a series of canted standing spin-wave (CSSW) states into a horizontal standing spin-wave (HSSW) state. The PSSW, CSSW and HSSW states are well described using a multilayer model of the Py film. The observation of CSSW modes is of particular relevance to microwave assisted magnetic recording, where microwave excitation stimulates precession of a soft layer canted out of plane by a pulsed magnetic field.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2022

Plasmon spectroscopy for the determination of Ti 3 C 2 T x MXene few layer stacks architecture

Like many 2D materials, numerous properties of MXene multilayers, and especially the most popular one Ti 3 C 2 T x , have been shown to significantly depend on their architecture, i.e. the number of layers and interlayer distance. These structural parameters are thus key elements to be characterized for the analysis of MXene properties. Focusing on valence electron energy-loss spectroscopy (VEELS) as performed in a transmission electron microscope (TEM), and using density functional theory (DFT) simulations, we here analyze the layer dependent large changes in the VEEL spectra of Ti 3 C 2 T x multilayers as a probe of their total thickness, and emphasize the bulk plasmon energy sensitivity to interlayer distance. Together these findings allow to directly quantify the absolute number of layers in a Ti 3 C 2 T x stack up to ~10 nm thickness and give access to interlayer distance modifications with sub-angström sensitivity, evidencing VEELS as a powerful method for the characterization of MXene multilayers on the nanometer scale. We expect these results to be relevant for the study of structure/properties correlations in this class of materials, especially with the development of in situ or environmental TEM experiments.

Materials Science↗
DOE OSTI2021

Prospects for the expansion of standing wave ambient pressure photoemission spectroscopy to reactions at elevated temperatures

Standing wave ambient pressure photoemission spectroscopy (SWAPPS) is a promising method to investigate chemical and potential gradients across solid-vapor and solid-liquid interfaces under close-to-realistic environmental conditions, far away from high vacuum. Until now, these investigations have been performed only near room temperature, but for a wide range of interfacial processes, chief among them being heterogeneous catalysis, measurements at elevated temperatures are required. One concern in these investigations is the temperature stability of the multilayer mirrors, which generate the standing wave field. At elevated temperatures, degradation of the multilayer mirror due to, for example, interdiffusion between the adjacent layers, decreases the modulation of the standing wave field, thus rendering SWAPPS experiments much harder to perform. Here, we show that multilayer mirrors consisting of alternate B4C and W layers are stable at temperatures exceeding 600 °C and are, thus, promising candidates for future studies of surface and subsurface species in heterogeneous catalytic reactions using SWAPPS.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1982

X-ray and extreme ultraviolet imaging using layered synthetic microstructures

Up to now designers of X-ray optical instruments such as microscopes and telescopes have been compelled to use mirrors operating at small glancing angles. However, using vapor deposition techniques, it is now possible to build multilayered thin film structures in which the individual layers have thicknesses comparable with a wavelength of X-rays. These devices operate in a manner exactly analogous to multilayer dielectric coatings at visible wavelengths and can be used to increase the X-ray and extreme ultraviolet reflectivity of surfaces at large glancing angles. These X-ray mirrors have numerous potential applications in X-ray optics. Attention is given to X-ray images with a normal incidence mirror, and applications of multilayer optics. Single-mirror telescopes for solar/stellar astronomy are discussed, taking into account solar corona and transition region studies, and X-ray and extreme ultraviolet astronomy. Hybrid X-ray telescopes are also considered.

Underwood, J. H.↗
NASA NTRS1984

Solar corona studies using normal-incidence X-ray optics

The progress which has been made in constructing a new type of X-ray telescope, which operates at normal incidence in the soft X-ray region by the use of multilayer coatings is described. The principles involved in state-of-the-art multilayer technology and some high-resolution imaging results are discussed. A rocket payload incorporating a multilayer X-ray mirror is presently being constructed. It is of Ritchey-Chretien design and the expected spatial resolution is 1/4 arcsec. The scientific program for solar-coronal studies and future instrumental developments are also discussed.

Golub, L.↗
NASA NTRS1988

Development of sputter coatings for the gravity probe B gyroscope housings

Cu/Ti coatings have been applied by sputter deposition to fused quartz housings to serve as the electrodes and lands of electrostatically supported gyroscopes. Niobium-coated fused quartz gyro rotors have been successfully suspended and spun up in those housings. The Cu/Ti bilayer coating and alternative multilayer coatings (Cu/Mo, Mo/Cu/Ti and Mo/Cu/Mo) with 2-micron thickness produced by sputter deposition on flat, fused quartz substrates have been examined with scanning electron microscopy, X-ray diffraction, X-ray photoelectron spectroscopy, and four-point resistivity measurement techniques. The multilayer coatings with a molybdenum bonding layer appear to produce smoother surfaces than those with a titanium bonding layer. All multilayer coatings survived thermal cycling to 77 K without adhesion failure.

Zhou, P.↗
NASA NTRS1988

Soft X-ray images of the solar corona using normal incidence optics

A solar coronal loop system has been photographed in soft X-rays using a normal incidence telescope based on multilayer mirror technology. The telescope consisted of a spherical objective mirror of 4 cm aperture and 1 m focal length, a film cassette, and a focal plane shutter. A metallized thin plastic film filter was used to exclude visible light. The objective mirror was covered with a multilayer coating consisting of alternating layers of tungsten and carbon whose combined thicknesses satisfied the Bragg diffraction condition for 44 A radiation. The image was recorded during a rocket flight on October 25, 1985 and was dominated by emission lines arising from the Si XII spectrum. The rocket also carried a high resolution soft X-ray spectrograph that confirmed the presence of Si XII line radiation in the source. This image represents the first successful use of multilayer technology for astrophysical observations.

Bruner, M. E.↗
NASA NTRS1995

Low earth orbit durability of protected silicone for refractive photovoltaic concentrator arrays

Photovoltaic power systems with novel refractive silicone solar concentrators are being developed for use in low Earth orbit (LEO). Because of the vulnerability of silicones to atomic oxygen and ultraviolet radiation, these lenses are coated with a multilayer metal oxide protective coating. The objective of this work was to evaluate the effects of atomic oxygen and thermal exposures on multilayer coated silicone. Samples were exposed to high-fluence ground-laboratory and low-fluence in-space atomic oxygen. Ground testing resulted in decreases in both total and specular transmittance, while in-space exposure resulted in only small decreases in specular transmittance. A contamination film, attributed to exposed silicone at coating crack sites, was found to cause transmittance decreases during ground testing. Propagation of coating cracks was found to be the result of sample heating during exposure. The potential for silicone exposure, with the resulting degradation of optical properties from silicone contamination, indicates that this multilayer coated silicone is not durable for LEO space applications where thermal exposures will cause coating crack development and propagation.

McCollum, Timothy A.↗
NASA NTRS2001

Cloud Overlapping Detection Algorithm Using Solar and IR Wavelengths With GOSE Data Over ARM/SGP Site

One of the most perplexing problems in satellite cloud remote sensing is the overlapping of cloud layers. Although most techniques assume a 1-layer cloud system in a given retrieval of cloud properties, many observations are affected by radiation from more than one cloud layer. As such, cloud overlap can cause errors in the retrieval of many properties including cloud height, optical depth, phase, and particle size. A variety of methods have been developed to identify overlapped clouds in a given satellite imager pixel. Baum el al. (1995) used CO2 slicing and a spatial coherence method to demonstrate a possible analysis method for nighttime detection of multilayered clouds. Jin and Rossow (1997) also used a multispectral CO2 slicing technique for a global analysis of overlapped cloud amount. Lin et al. (1999) used a combination infrared, visible, and microwave data to detect overlapped clouds over water. Recently, Baum and Spinhirne (2000) proposed 1.6 and 11 microns. bispectral threshold method. While all of these methods have made progress in solving this stubborn problem, none have yet proven satisfactory for continuous and consistent monitoring of multilayer cloud systems. It is clear that detection of overlapping clouds from passive instruments such as satellite radiometers is in an immature stage of development and requires additional research. Overlapped cloud systems also affect the retrievals of cloud properties over the ARM domains (e.g., Minnis et al 1998) and hence should identified as accurately as possible. To reach this goal, it is necessary to determine which information can be exploited for detecting multilayered clouds from operational meteorological satellite data used by ARM. This paper examines the potential information available in spectral data available on the Geostationary Operational Environmental Satellite (GOES) imager and the NOAA Advanced Very High Resolution Radiometer (AVHRR) used over the ARM SGP and NSA sites to study the capability of detecting overlapping clouds

Kawamoto, Kazuaki↗
NASA NTRS2001

Cloud Overlapping Detection Algorithm Using Solar and IR Wavelengths with GOES Data Over ARM/SGP Site

One of the most perplexing problems in satellite cloud remote sensing is the overlapping of cloud layers. Although most techniques assume a one layer cloud system in a given retrieval of cloud properties, many observations are affected by radiation from more than one cloud layer. As such, cloud overlap can cause errors in the retrieval of many properties including cloud height, optical depth, phase, and particle size. A variety of methods have been developed to identify overlapped clouds in a given satellite imager pixel. Baum et al used CO2 slicing and a spatial coherence method to demonstrate a possible analysis method for nighttime detection of multilayered clouds. Jin and Rossow also used a multispectral CO2 slicing technique for a global analysis of overlapped cloud amount. Lin et al. used a combination infrared (IR), visible (VIS), and microwave data to detect overlapped clouds over water. Recently, Baum and Spinhirne proposed a 1.6 and 11 micron bispectral threshold method. While all of these methods have made progress in solving this stubborn problem none have yet proven satisfactory for continuous and consistent monitoring of multilayer cloud systems. It is clear that detection of overlapping clouds from passive instruments such as satellite radiometers is in an immature stage of development and requires additional research. Overlapped cloud systems also affect the retrievals of cloud properties over the Atmospheric Radiation Measurement (ARM) domains and hence should be identified as accurately as possible. To reach this goal, it is necessary to determine which information can be exploited for detecting multilayered clouds from operational meteorological satellite data used by ARM. This paper examines the potential information available in spectral data available on the Geostationary Operational Environmental Satellite (GOES) imager and the National Oceanic Atmospheric Administration (NOAA) Advanced Very High Resolution Radiometer (AVHRR) used over the ARM Program's Southern Great Plains (SGP), and North Slope of Alaska (NSA) sites to study the capability of detecting overlapping clouds.

Kawamoto, K.↗