Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “linear scaling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 973 records · Page 54

Effects of eddy initial conditions on nonlinear forcing of planetary scale waves by amplifying baroclinic eddies

The previous study of Young and Villere concerning growth of planetary scale waves forced by wave-wave interactions of amplifying intermediate scale baroclinic eddies is extended to investigate effects of different eddy initial conditions. A global, spectral, primitive equation model is used for the calculations. For every set of eddy initial conditions considered, growth rates of planetary modes are considerably greater than growth rates computed from linear instability theory for a fixed zonally independent basic state. However, values of growth rates ranged over a factor of 3 depending on the particular set of eddy initial conditions used. Nonlinear forcing of planetary modes via wave-wave coupling becomes more important than baroclinic growth on the basic state at small values of the intermediate-scale modal amplitudes. The relative importance of direct transfer of kinetic energy from intermediate scales of motion to a planetary mode, compared to baroclinic conversion of available potential energy to kinetic energy within that planetary mode, depends on the individual case. In all cases, however, the transfer of either kinetic or available potential energy to the planetary modes was accomplished principally by wave-wave transfer from intermediate scale eddies, rather than from the zonally averaged state. The zonal wavenumber 2 planetary mode was prominent in all solutions, even in those for which eddy initial conditions were such that a different planetary mode was selectively forced at the start. General characteristics of the structural evolution of the planetary wave components of total heat and momentum flux, and modal structures themselves, were relatively insensitive to variations in eddy initial conditions, even though quantitative details varied from case to case.

Young, Richard E.↗

Advanced turbo-prop airplane interior noise reduction-source definition

Acoustic pressure amplitudes and phases were measured in model scale on the surface of a rigid semicylinder mounted in an acoustically treated wind tunnel near a prop-fan (an advanced turboprop with many swept blades) model. Operating conditions during the test simulated those of a prop-fan at 0.8 Mach number cruise. Acoustic pressure amplitude and phase contours were defined on the semicylinder surface. Measurements obtained without the semi-cylinder in place were used to establish the magnitude of pressure doubling for an aircraft fuselage located near a prop-fan. Pressure doubling effects were found to be 6dB at 90 deg incidence decreasing to no effect at grazing incidence. Comparisons of measurements with predictions made using a recently developed prop-fan noise prediction theory which includes linear and non-linear source terms showed good agreement in phase and in peak noise amplitude. Predictions of noise amplitude and phase contours, including pressure doubling effects derived from test, are included for a full scale prop-fan installation.

Magliozzi, B.↗

Gravity waves in Titan's atmosphere

Scintillations (high frequency variations) observed in the radio signal during the occultation of Voyager 1 by Titan (Hinson and Tyler, 1983) provide information concerning neutral atmospheric density fluctuations on scales on hundreds of meters to a few kilometers. Those seen at altitudes higher than 25 km above the surface were interpreted by Hinson and Tyler as being caused by linear, freely propagating (energy-conserving) gravity waves, but this interpretation was found to be inconsistent with the scintillation data below the 25-km altitude level. Here an attempt is made to interpret the entire scintillation profile between the surface and the 90-km altitude level in terms of gravity waves generated at the surface. Numerical calculations of the density fluctuations caused by two-dimensional, nonhydrostatic, finite-amplitude gravity waves propagating vertically through Titan's atmosphere are performed to produce synthetic scintillation profiles for comparison with the observations. The numerical model accurately treats the effects of wave transience, nonlinearity, and breakdown due to convective instability in the overturned part of the wave. The high-altitude scintillation data were accurately recovered with a freely propagating wave solution, confirming the analytic model of Hinson and Tyler. It is found that the low-altitude scintillation data can be fit by a model where a component of the gravity waves becomes convectively unstable and breaks near the 15 km level. The large-scale structure of the observed scintillation profile in the entire altitude range between 5 and 85 km can be simulated by a model where the freely propagating and breaking waves are forced at the surface simultaneously. Further analysis of the Voyager 1 Titan low-altitude scintillation data, using inversion theory appropriate for strong scattering, could potentially remove some of the ambiguities remaining in this analysis and allow a better determination of the strength and source of the waves.

Friedson, A. James↗

Organized motions underlying turbulent shear flows

The objective of this project is to determine the nature and significance of the organized motions underlying turbulent shear flow. There is considerable experimental evidence for the existence of such motions. In particular, one consistently observes longitudinal streaks with a spacing of about 100 in wall units in the near-wall region of wall-bounded shear flows. Recently, an analysis based on the direct resonance mechanism has predicted the appearance of streaks with precisely such a spacing. Also, the minimum channel simulations of Jimenez and Moin have given a strong dynamical significance to that spanwise length scale. They have shown that turbulent-like flows can not be maintained when the spanwise wavelength of the motion is constrained to be less than about that critical number. A critical review of the direct resonance ideas and the non-linear theory of Benney and Gustavsson is presented first. It is shown how this leads to the later mean flow-first harmonic theory of Benney. Finally, we note that a different type of analysis has led to the prediction streaks with a similar spacing. This latter approach consists of looking for optimum fields and directly provides deep insights into why a particular structure or a particular scale should be preferred.

Waleffe, F.↗

The Large Scale X-Ray Emission from M87

We describe asymmetrical features in a long exposure X-ray map of M87 made with the ROSAT High Resolution Imager (HRI). A bright triangular region is marked by a linear 'spur' along one edge. The structure of this spur suggests an interpretation of a tangential view of a shock front 18 kpc long. None of the brighter features are spatially coincident with radio or optical structures so we concur with earlier investigators that most of the emission arises from thermal processes.

Harris, D. E.↗

On stability of large-scale systems under structural perturbations.

The concept of connective stability of large-scale systems is widened to include arbitrary structural perturbations. Conditions for this broader kind of connective stability are derived by developing 'connective' versions of both the linear and the nonlinear comparison principles.

Siljak, D. D.↗

On stability of large-scale systems under structural perturbations.

The concept of connective stability of large-scale systems is widened to include arbitrary structural perturbations. Conditions for this broader kind of connective stability are derived by developing connective versions of both the linear and the nonlinear comparison principle.

Siljak, D. D.↗

Measurement of the dispersive and refractive indices of germanium using diode lasers

Germanium Fabry-Perot etalons are commonly used in diode laser spectroscopy to establish relative frequency calibration scales for molecular absorption spectra. Typically the channel spectrum of the etalon is recorded simultaneously with the molecular spectrum as the laser injection current is tuned linearly, and the etalon free spectral range (fringe spacing) is used to measure the frequency separations among lines in the molecular spectrum. For this purpose, the etalon free spectral range must be known for the measurement wavelength, and this in turn relies on knowledge of the etalon length and the dispersive index at this wavelength. It is pointed out that the most satisfactory approach is to measure directly the free spectral range or dispersive index of the etalon at the wavelength of interest. A description is presented of measurements of this type, performed near 7.9 and 10.1 micrometers for a 7.7-cm long germanium etalon.

Jennings, D. E.↗

Improving a NASTRAN dynamic model with test data using LINWOOD

The concept of expressing test modes as a linear combination of analytical modes was applied to the prediction of corrective terms in math model mass and stiffness. Test data for the Space Shuttle quarter scale solid rocket booster were analyzed by this method and significant improvements in frequency and mode shap correlation are noted. The applicability of the method is demonstrated.

Ujihara, B. H.↗

On the shock cell structure and noise of supersonic jets

A linear solution modeling the shock cell structure of an axisymmetric supersonic jet operated at off-design conditions is developed by the method of multiple-scales. The model solution takes into account the gradual spatial change of the mean flow in the downstream direction. Turbulence in the mixing layer of the jet has the tendency of smoothing out the sharp velocity and density gradients induced by the shocks. To simulate this effect, eddy viscosity terms are incorporated in the model. It is known that the interaction between the quasi-periodic shock cells and the downstream propagating large turbulence structures in the mixing layer of the jet is responsible for the generation of broadband shock associated noise. Experimentally, the dominant part of this noise has been found to originate from the part of the jet near the end of the potential core. Calculated shock cell spacing at the end of the jet core according to the present model is used to estimate the peak frequencies of the shock associated noise for a range of observation angles. Very favorable agreement with experimental measurements is found.

Tam, C. K. W.↗

Linear prediction filters for linear and nonlinear modeled geomagnetic activity

It is shown that the Faraday loop analog model of geomagnetic activity exhibits both the directly driven and loading-unloading magnetospheric responses to solar wind input. It is further shown that the directly driven component is a linear response to loading while the loading-unloading response is nonlinear. Linear prediction filters which relate model input to output are discussed. By either allowing or suppressing the loading-unloading model response filters that relate to nonlinear or linear dynamics, respectively, have been computed. Filters that described the directly driven response are finite ranged; they asymptote to zero with increasing lag on a time scale that is fixed by the dissipation rate of the model. Filters that describe the nonlinear total response are infinite ranged; they asymptote with increasing lag to large amplitude periodic oscillations. Some implications of these infinite ranged filters are discussed.

Klimas, A. J.↗

Nonlinear symmetric instability and intraseasonal oscillations in the tropical atmosphere

Symmetric inertial instability (SII) is studied as a mechanism for stratospheric and tropospheric phenomena in the equatorial regions. The linear and nonlinear dynamics of SII in a two-layer, zonally symmetric model on an equatorial beta plane, in the presence of a basic flow with horizontal and vertical shear, with and without dissipative effects are investigated. Linear symmetric instabilities are, in accordance with previously published results, purely exponential, that is, nonoscillatory. Nonlinear SII, studied here for the first time on a planetary scale, can produce finite-amplitude oscillatory behavior, periodic or chaotic. The period of oscillations in the inviscid case depends on the initial data. In the presence of dissipative effects, all solutions tend to a limit cycle or to a strange attractor. The dominant period in this case, over a wide range of parameters and whether vertical shear is present or not, is in the intraseasonal, 20-30-day range. It appears therefore that nonlinear SII might be a contributing mechanism to low-frequency oscillations in the tropical atmosphere.

Zhao, J.-X.↗

Non-parallel stability of compressible boundary layers

Linear and nonlinear stability of compressible growing boundary layers is studied using parabolized stability equations (PSE). Linear PSE calculations are performed for Mach 1.6 and 4.5 plate-plate flow, and the results are compared with the predictions of the multiple-scales approach. In general, the nonparallel effect appears to be less significant for oblique waves near the lower neutral branch but it progressively becomes important at higher Reynolds numbers near the upper branch. In contrast, the nonparallel effect is more pronounced near the lower branch for two-dimensional first-mode waves. The PSE and multiple-scales results agree for the first mode waves, but in the first-second mode transition region, the latter approach tends to break down. Comparison with the first (oblique) and second mode growth rate data from Kendall's (1967) experiment shows good agreement; however, the peak second mode growth rate is over-predicted. Similar conclusions are drawn for the second mode experiment of Stetson et al. (1983) for Mach 8 flow past a sharp cone. We conjecture that the lower experimental growth rate is due to nonlinear saturation and provide supporting calculations.

Chang, Chau-Lyan↗

Mesosphere Dynamics with Gravity Wave Forcing: Planetary Waves - 2

We present results from a non-linear, 3D, time dependent numerical spectral model (NSM) which extends from the ground up into the thermosphere and incorporates Hines' Doppler Spread Parameterization for small-scale gravity waves (GW). Our focal point is the mesosphere where wave interactions are playing a dominant role. We discuss planetary waves in the present paper and diurnal and semi-diurnal tides in the companion paper. Without external time dependent energy or momentum sources, planetary waves (PWs) are generated in the model for zonal wavenumbers 1 to 4, which have amplitudes in the mesosphere above 50 km as large as 30 m/s and periods between 2 and 50 days. The waves are generated primarily during solstice conditions, which indicates that the baroclinic instability (associated with the GW driven reversal in the latitudinal temperature gradient) is playing an important role. Results from a numerical experiment show that GWs are also involved directly in generating the PWs. For the zonal wavenumber m = 1, the predominant wave periods in summer are around 4 days and in winter between 6 and 10 days. For m = 2, the periods are in summer and close to 2.5 and 3.5 days respectively For m = 3, 4 the predominant wave periods are in both seasons close to two days. The latter waves have the characteristics of Rossby gravity waves with meridional winds at equatorial latitudes. A common feature of the PWs (m = 1 to 4) generated in summer and winter is that their vertical wavelengths throughout the mesosphere are large which indicates that the waves are not propagating freely but are generated throughout the region. Another common feature is that the PWs propagate preferentially westward in summer and eastward in winter, being launched from the westward and eastward zonal winds that prevail respectively in summer and winter altitudes below 80 km. During spring and fall, for m = 1 and 2 eastward propagating long period PWs are generated that are launched from the smaller eastward zonal winds that prevail in these seasons. PWs generated in the model produce large amplitude modulations of the diurnal tides at altitudes above 80 km and contribute to their seasonal variations.

Mayr, H. G.↗

Channels and Fan-like Features on Titan Surface Imaged by the Cassini RADAR

During two close flybys of Titan on October 26, 2004, and February 15, 2005, the Cassini s radar instrument acquired synthetic-aperture radar (SAR) data revealing Titan s complex surface and intriguing geological features. Fan-like and apparently flow-related features are connected to sinuous and linear features which resemble channels. The fan-like features and channels appear to be relatively SAR-bright and suggest surface roughness properties at the scale and bigger than the Ku-band, and possible volume scattering. A strong correlation between the SAR-bright and radiometric cold regions has been observed. The correlation is consistent with radiometric cold areas being caused by volume scattering at Ku as due to broken low-loss ice and resulting low emissivity as with the surfaces of Europa and Ganymede.

Paganelli, F.↗

The Primordial Inflation Polarization Explorer (PIPER)

The Primordial Inflation Polarization Explorer (PIPER) is it balloon-borne instrument designed to search for the faint signature of inflation in the polarized component of the cosmic microwave background (C-N-113). Each flight will be configured for a single frequency, but in order to aid in the removal of the polarized foreground signal due to Galactic dust, the filters will be changed between flights. In this way, the CMB polarization at a total of four different frequencies (200, 270, 350, and 600 GHz) will be, measured on large angular scales. PIPER consists of a pair of cryogenic telescopes, one for measuring each of Stokes Q and U in the instrument frame. Each telescope receives both linear orthogonal polarizations in two 32 x 40 element planar arrays that utilize Transition-Edge Sensors (TES). The first element in each telescope is a variable-delay polarization modulator (VPM) that fully modulates the linear Stokes parameter to which the telescope is sensitive. There are several advantages to this architecture. First, by modulating at the front of the optics, instrumental polarization is unmodulated and is therefore cleanly separated from source polarization. Second, by implementing this system with the appropriate symmetry, systematic effects can be further mitigated. In the PIPER design, many of the. systematics are manifest in the unmeasured linear Stokes parameter for each telescope and this can be separated from the desired signal. Finally, the modulation cycle never mixes the Q and U linear Stokes parameters, and thus residuals in the modulation do not twist the observed polarization vector. This is advantageous because measuring the angle of linear polarization is critical for separating the inflationary signal from other polarized components.

Chuss, David T.↗

Large Scale Flutter Data for Design of Rotating Blades Using Navier-Stokes Equations

A procedure to compute flutter boundaries of rotating blades is presented; a) Navier-Stokes equations. b) Frequency domain method compatible with industry practice. Procedure is initially validated: a) Unsteady loads with flapping wing experiment. b) Flutter boundary with fixed wing experiment. Large scale flutter computation is demonstrated for rotating blade: a) Single job submission script. b) Flutter boundary in 24 hour wall clock time with 100 cores. c) Linearly scalable with number of cores. Tested with 1000 cores that produced data in 25 hrs for 10 flutter boundaries. Further wall-clock speed-up is possible by performing parallel computations within each case.

Guruswamy, Guru P.↗

Model Validation for Propulsion - On the TFNS and LES Subgrid Models for a Bluff Body Stabilized Flame

This paper summarizes the reacting results of simulating a bluff body stabilized flame experiment of Volvo Validation Rig using a releasable edition of the National Combustion Code (NCC). The turbulence models selected to investigate the configuration are the sub-grid scaled kinetic energy coupled large eddy simulation (K-LES) and the time-filtered Navier-Stokes (TFNS) simulation. The turbulence chemistry interaction used is linear eddy mixing (LEM).

Flame↗